works fine...now i`m thinking about experimenting with mang`s custom fw i understand it has a different interface?is it better?:)
(Last edited by LocoMatt on 7 Sep 2011, 20:39)
The content of this topic has been archived between 12 Apr 2018 and 7 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
works fine...now i`m thinking about experimenting with mang`s custom fw i understand it has a different interface?is it better?:)
(Last edited by LocoMatt on 7 Sep 2011, 20:39)
hi
i had a problem with mr3420 i upgraded my firmware with open wrt and know i want to go back to original tp link firmware how can i do that tell me an easy way
thanks
i thin that when i connect my tp link with computer it is not connected plz help me
i stuck at password and i do not set it plz tell me what to do
plz help me hurry thanks when i login through winscp it ask me pasword which i dont khow and i didnot set it i did not set default password knoe how to know the password plz tell me in details thanks
plz help me hurry thanks when i login through winscp it ask me pasword which i dont khow and i didnot set it i did not set default password knoe how to know the password plz tell me in details thanks
you must set password first, you can using putty login telnet
# passwd <enter>
enter new password twice
now, you can login with Winscp
http://mangkaning.0fees.net/image/setwinscp.jpg
http://mangkaning.0fees.net/image/winscpwin.jpg
I have racked network config and now cannot get access with putty or telnet.
Router works, but something wrong with ip addreses.
Can I somehow launch router with default configs?
-----
Problem solved. I was able to connect by telnet in safe mode
(Last edited by jimmy364 on 17 Sep 2011, 19:51)
very very thanks mang now i had copy the firmware file to tmp folder now what to do next
run Putty
type:
cd /tmp
mtd -r write /tmp/code.bin firmware
now it should install the new firmawre, you just need to wait untill it reboots.
now where to write that so that router install firware ?
very very thanks again
very very thanks mang now i had copy the firmware file to tmp folder now what to do next
run Putty
type:
cd /tmp
mtd -r write /tmp/code.bin firmware
now it should install the new firmawre, you just need to wait untill it reboots.now where to write that so that router install firware ?
very very thanks again
after place file image to folder "/tmp" you need rename that... example rename "code.bin"
you copy command below to putty:
cd /tmp
mtd -e firmware -r write code.bin firmware
reboot
but if you copy sysupgrade.bin to /tmp, that command:
cd /tmp
sysupgrade code.bin
reboot
Help With My TL-MR3220 v2.0
Has Bricked
With Putty Show This:
U-Boot 1.1.4 (Jul 3 2012 - 16:08:01)
AP121 (ar9330) U-boot
DRAM: 32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... Too big uncompressed streamLZMA ERROR 1 - must RESET
Is a Loop
Hello!
I have an M3420 V2 Tp_link router and i want to restore original firmware.
I have uploaded it with WinSCP, logged in with putty.
When I enter the mtd command - (mtd -r write /tmp/original.bin firmware) - I receive a "Failed to erase block) If i choose not to check the blocks, then I got an "Error writing image" error.
Any idea?
BR,
Batka
The discussion might have continued from here.