Topic: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Hi I have an asus wl-520gu with x-wrt kamikaze 8.09.2 brcm-2.4.xx how to get working this modem the big problem is I'm newbies on linux

2

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Tried usb-modeswitch?

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Dogge wrote:

Tried usb-modeswitch?

I note that (most) *trunk* builds of OpenWRT are now using the 2.6.32 kernel, and at least for my Huawei E176, special commands (huaweitkbbo, usb-modeswitch, etc.) no longer seem to be required to access the device.

After bootup, the /dev/ttyUSB devices appear magically, and the SCSI interface for the built-in SD card reader also appears simultaneously with no effort. (This wasn't the case with the previous 2.6.30 kernel.)

For trunk, all I needed to do was to install the right packages (kmod-usb-serial, kmod-usb-serial-option, comgt and chat), and I then set up the appropriate '3g' interface in /etc/config/network.

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

There's an excellent tutorial at http://josefsson.org/openwrt/dongle.html which will hopefully be applicable. Good luck!

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

yes I try with this how to  http://josefsson.org/openwrt/dongle.html and I have one problem" timeout for checking pin.failed to set up pincode"I dont understend where is the mistake

6 (edited by staylo 2010-02-08 14:01:38)

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Really sorry - didn't notice your post. I've subscribed to this topic so I'll be able to give a response quicker this time!

This part of the code is quite badly written; that's basically a generic error (the problem could be pretty much anything). Please post the console output of the following:

cat /etc/config/network

ifup your_3g_interface_name

logread (after doing the 'ifup' line above)

ls /dev/ | grep ttyUSB

Thanks!

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Thank's for your answer but now I lose my huawei e1750 device in the weekend,today I get another but not huawei its a option icon 225 hsdpa modem and now I must to starting again with my new device if somebody could write an largest tutorial for this device with 2.4.xx kernel because I need the wireless interface I will gonn be verry happy

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

no body else could help me with this device?

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

hello!

there's a dd-wrt build for broadcom routers here:
http://dd-wrt.com/phpBB2/viewtopic.php?t=50531&start=90
maybe it will hep you - try it.

10

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

maurer wrote:

there's a dd-wrt build for broadcom routers here:
http://dd-wrt.com/phpBB2/viewtopic.php?t=50531&start=90
maybe it will hep you - try it.

This is not a DD-WRT forum. Discuss about DD-WRT somewhere else...

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Thanks for your answeare but the problem its with the option icon 225 3g usb modem openwrt its not so beautiful like dd-wrt but better and easy to use and more else.Now i got work a 3g usb broadband with asus wl520gu (: (huawei e220) work verry well  only now i have to modems
If sombody could helpme with  option icon 225 I will be gonabe verry happy  Thankyou

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Hi all!

I have a TP-Link WR1043ND and this f**** E1750 usb modem.
I tried to get it working, but my router does not recognize the modem, just the SCSI stuffs.
I tried to switch modes with usb_modeswitch and also with huaweiaktbbo (which says not supported).
So I'm stucked at the moment.
Here is dmesg:
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
usb-storage: device scan complete
scsi 1:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete

And here is the lsusb result:
Bus 001 Device 002: ID 12d1:1446 Huawei Technologies Co., Ltd.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

I know the correct VID, PID is 0x12d1  and 0x1001 for the modem. Checked on PC...

So it seems to me that somehow the stick is not recognized correctly.

Can somebody help me?

Regards,
Begi

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

Check: http://www.it-slav.net/blogs/2010/06/12/howto-use-3g-dongle-huawei-e1750-in-openwrt/
I did it 10 minutes ago (1043+e1750) succesfully

14 (edited by Begi 2011-04-03 22:37:13)

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

JaromirN wrote:

Check: http://www.it-slav.net/blogs/2010/06/12/howto-use-3g-dongle-huawei-e1750-in-openwrt/
I did it 10 minutes ago (1043+e1750) succesfully

Thanks a lot!

It turned out that I missed the installation of kmod-usb-serial-option.
After installing it everything works fine.

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

essdz wrote:
Dogge wrote:

Tried usb-modeswitch?

I note that (most) *trunk* builds of OpenWRT are now using the 2.6.32 kernel, and at least for my Huawei E176, special commands (huaweitkbbo, usb-modeswitch, etc.) no longer seem to be required to access the device.

After bootup, the /dev/ttyUSB devices appear magically, and the SCSI interface for the built-in SD card reader also appears simultaneously with no effort. (This wasn't the case with the previous 2.6.30 kernel.)

For trunk, all I needed to do was to install the right packages (kmod-usb-serial, kmod-usb-serial-option, comgt and chat), and I then set up the appropriate '3g' interface in /etc/config/network.

Looking not. I have BF 10.3.1 = 2.6.32.16  and should be used flip-flop switching here.

Re: Huawei E1750 3g usb modem aka T-mobile web'n'walk V in Hungary Help

dude,

i have another question.. my E1750 not accepting CPIN or CARDLOCK commands at all.. (reporting +CME  operation not permitted  or something like this)

Do you have some experience with this case?