Hi
i buy this modem routuer via my ISP club internet its a dedicate box cant find manufacture
i open it end plug a serial cable after he load his setting to acces he ask me a username end password
any suggestion ? a way to change the password ? thanks
CFE version 1.0.37-0.6 for BCM96348 (32bit,SP,BE)
Build Date: ¥| 3¤ë 3 18:53:59 CST 2005 (root@hp)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena.
Initializing Devices.
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory used by CFE: 0x80401000 - 0x80522C60 (1186912)
Initialized Data: 0x8041ADB0 - 0x8041C600 (6224)
BSS Area: 0x8041C600 - 0x80420C60 (18016)
Local Heap: 0x80420C60 - 0x80520C60 (1048576)
Stack Area: 0x80520C60 - 0x80522C60 (8192)
Text (code) segment: 0x80401000 - 0x8041ADB0 (105904)
Boot area (physical): 0x00523000 - 0x00563000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id Name :
Psi size in KB : 24
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:03:c9:9e:04:af
Ethernet PHY Type : Internal
Memory size in MB : 16
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80188018
Decompression OK!
Entry at 0x80188018
Closing network.
Starting program at 0x80188018
Linux version 2.6.8.1 (root@hp) (gcc version 3.4.2) #1 Thu Dec 7 17:03:53 CST 20
06
Flash device ID:22a7
MXIC FLASH FAMILY
Total Flash size: 4096K with 71 sectors
***Board is not initialized****: Using the default PSI size: 24
96348GW prom init
CPU revision is: 00029107
mpi: No Card is in the PCMCIA slot
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 14112k/16000k available (1303k kernel code, 1868k reserved, 196k data, 7
2k init, 0k highmem)
Calibrating delay loop... 253.44 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 801547cc
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=1 sec (nowa
yout= 0)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
bcm963xx_serial driver v2.0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET: Registered protocol family 1
NET: Registered protocol family 17
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2006.12.07-09:06+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2006.12.07-09:06+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348A2 Ethernet Network Device v0.3 Dec 7 2006 17:02:47
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:03:C9:9E:04:AF
Broadcom BCM6348A2 Ethernet Network Device v0.3 Dec 7 2006 17:02:47
Config External PHY Through MDIO
Correct Ext PHY address: 17
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth1: MAC Address: 00:03:C9:9E:04:B0
Broadcom BCM6348A2 USB Network Device v0.4 Dec 7 2006 17:02:48
usb0: MAC Address: 00 03 C9 9E 04 B1
usb0: Host MAC Address: 00 03 C9 9E 04 B2
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl0: Broadcom BCM4318 802.11 Wireless Controller 3.91.23.0
Endpoint: endpoint_init entry
BOS: Enter bosInit
BOS: Enter bosAppInit
BOS: Exit bosAppInit
BOS: Exit bosInit
Endpoint: endpoint_init COMPLETED
BcmAdsl_Initialize=0xC00521C8, g_pFnNotifyCallback=0xC00665E4
AdslCoreHwReset: AdslOemDataAddr = 0xA0FFB2E4
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
==> Bcm963xx Software Version: AH4021.01.2.01.300L01.V44-08.mgcp.dspApp3341_fx
o.LE9500 A2pB019b11.d16m <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device eth1 entered promiscuous mode
br0: port 3(eth1) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1) entering forwarding state
Key Input : TECOM-AH4021-9E04AF
Key Output: 4F B7 76 46 9D 15 3B CC 08 31 DB BE 39 45 6B 6F DB B0 E9 32
Setting country code "FR"
channel selected 11
channel selected 11
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
br0: port 4(wl0) entering disabled state
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device eth1 left promiscuous mode
br0: port 3(eth1) entering disabled state
device eth1 entered promiscuous mode
br0: port 3(eth1) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1) entering forwarding state
device wl0 left promiscuous mode
br0: port 4(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
Starting the MGCP application with the following parameters:
Call Agent IP address/FQDN: rtp.voip.club-internet.fr
Gateway name: ci10557432
Interface name: any
Preferred codec: auto
kernel::endpoint_open
kernel::endpoint_open COMPLETED
BOS: Enter bosInit
BOS: Enter bosAppInit
BOS: Exit bosAppInit
BOS: Exit bosInit
00:00:38 Calling callClient
try to probe the DNS server
app: /bin/dnsprobe &
00:00:38 ERROR resolving address rtp.voip.club-internet.fr by DNS Server.
=====================================================
Broadcom Canada, E-MTA CallClient.
Version: 1.1.
Build Date: Dec 7 2006 17:05:31.
=====================================================
00:00:39 GWCONFIG Data:
00:00:39 CA_#1 Name - ca@rtp.voip.club-internet.fr
00:00:39 CA_#2 Name - ca@rtp.voip.club-internet.fr
00:00:39 CA_#3 Name - ca@rtp.voip.club-internet.fr
00:00:39 GW Name - ci10557432
00:00:39 Interface name - any
00:00:39 Preferred Codec - auto
00:00:39 Country - FRA
00:00:39 AALN - 1
00:00:39 CA Port - 2427
00:00:39 MGC Port - 2427
00:00:39 TX Gain - 0
00:00:39 RX Gain - 0
00:00:39 PSTN Access Code - ##
00:00:39 Heartbeat Timer - 60
00:00:39 Emergency List -
Created queue HDSP
dnsprobe: Can not open /etc/resolv.conf
00:00:39 CALLCLIENT: Initializing endpoints
app: echo 0 > /var/telephone0_status
app: echo 0 > /var/telephone1_status
app: echo 0 > /var/mgcpstats
00:00:39 CALLCLIENT: Initializing endpoints
00:00:39 Endpoint will be initialized for country FRA (country code = 5)
00:00:39 Endpoint will be initialized for TX Gain: 0 dB, RX Gain: 0 dB
00:00:39 Endpoint Event task started with pid 518...
BOS: Created task eptEvent
00:00:39 Endpoint Packet task started with pid 519 ...
BOS: Created task eptPacket
BOS: Enter bosStartApp
BOS: bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
BOS: Enter TaskCreate aoAP
BOS: TaskCreate - spawn new task aoAP
bcmOsTaskCreate:
TASK NAME = aoAP
TASK_PRIORITY = 1
BOS: Exit TaskCreate
BOS: AppResetDetectionEnable() - Enabled reset detection.
bcmOsTaskCreate:
TASK NAME = aoRT
TASK_PRIORITY = 1
BOS: Exit bosStartApp
Reseting the 3341
voipResetGpio = 6
PASS: mmr
PASS: chipCtl
PASS: mspi
PASS: scratchSram
PASS: apmregs
PASS: apm0
PASS: apm1
PASS: hvg
PASS: slic
PASS: vpm
PASS: mbox
3341 diagnostics passed!
Reseting the 3341
voipResetGpio = 6
Initializing 3341 drivers
-------------- TDM DMA setup strt --------------
SAMPLESIZE = 8
DESCRIPTORP = 0xb7fe6300 INGRESSP = 0xb7fe6310 EGRESSP = 0xb7fe6330
Initializing Memory: 8 (16-bit locations)
Priming TX FIFO....
Completed TDM3341 init!!!!
MSPI driver init SUCCESSFUL
MSPI driver registers update SUCCESSFUL
BOARDHAL Enabling relays
Loading 3341 Zsp with Hausware app.
BOS: Enter TaskCreate 3341_ASSERT_IST
BOS: TaskCreate - spawn new task 3341_ASSERT_IST
bcmOsTaskCreate:
TASK NAME = 3341_ASSERT_IST
TASK_PRIORITY = 1
BOS: Exit TaskCreate
DSP Handshake. Hausware ZSP app initialized properly.
bosMsgQCreate: Created message queue VRGEVQ at address 0x8001
BOS: Enter TaskCreate VRGEVPR
BOS: TaskCreate - spawn new task VRGEVPR
bcmOsTaskCreate:
TASK NAME = VRGEVPR
TASK_PRIORITY = 1
BOS: Exit TaskCreate
BOS: Enter TaskCreate HCAS
BOS: TaskCreate - spawn new task HCAS
bcmOsTaskCreate:
TASK NAME = HCAS
TASK_PRIORITY = 1
BOS: Exit TaskCreate
ENDPT: Creating hausware task
BOS: Enter TaskCreate HTSK
BOS: TaskCreate - spawn new task HTSK
bcmOsTaskCreate:
TASK NAME = HTSK
TASK_PRIORITY = 1
BOS: Exit TaskCreate
DAA DBG: MSPI Hdl = 0x500
DAA DBG: GPIO Hdl = 0xb
DAA DBG: Successful READ!!!! count = 0
DAA DBG: ISOCAP lock count = 0
Si3050 SLAC Initialised, Line side device = Si: 3018 (0x1)
System dev rev: 0x4, Line dev rev: 0x3
Line dev status: FDT:0x1, LCS: 0x0
Si3050 Registers Values
Reg 0x1. Control 1 - 0x0 (Res 0xba)
Reg 0x2. Control 2 - 0x7 (Res 0xdf)
Reg 0x3. Int Mask - 0x0 (Res 0xff)
Reg 0x4. Int Source - 0x28 (Res 0xff)
Reg 0x5. DAA Ctrl 1 - 0x0 (Res 0x6d)
Reg 0x6. DAA Ctrl 2 - 0x0 (Res 0x18)
Reg 0x7. Smp Rate - 0x0 (Res 0x8)
Reg 0x8. Reserved - 0x0 (Res 0x0)
Reg 0x9. Reserved - 0x0 (Res 0x0)
Reg 0xa. DAA Ctrl 3 - 0x0 (Res 0x1)
Reg 0xb. S/LSD Rev - 0x14 (Res 0xff)
Reg 0xc. LSD Status - 0x40 (Res 0x5f)
Reg 0xd. LSD Rev - 0x4c (Res 0x3c)
Reg 0xe. DAA Ctrl 4 - 0x0 (Res 0x2)
Reg 0xf. T/R Gain 1 - 0x0 (Res 0x88)
Reg 0x10. Int Ctrl 1 - 0x0 (Res 0x53)
Reg 0x11. Int Ctrl 2 - 0x0 (Res 0xff)
Reg 0x12. Int Ctrl 3 - 0x0 (Res 0x2)
Reg 0x13. Int Ctrl 4 - 0x2 (Res 0x7)
Reg 0x14. CP Rx Atte - 0x0 (Res 0xff)
Reg 0x15. CP Tx Atte - 0x0 (Res 0xff)
Reg 0x16. Rg Ctrl 1 - 0x16 (Res 0xff)
Reg 0x17. Rg Ctrl 2 - 0x12 (Res 0xff)
Reg 0x18. Rg Ctrl 3 - 0x99 (Res 0xbf)
Reg 0x19. Res Calib - 0xe (Res 0xef)
Reg 0x1a. DC Ctrl - 0xc0 (Res 0xf3)
Reg 0x1b. Reserved - 0x7 (Res 0x0)
Reg 0x1c. Loop Sta - 0x0 (Res 0xff)
Reg 0x1d. Line V Sta - 0x0 (Res 0xff)
Reg 0x1e. AC Ctrl - 0x0 (Res 0xf)
Reg 0x1f. DAA Ctrl 5 - 0x20 (Res 0xeb)
Reg 0x20. Gd Sta Ctl - 0x3 (Res 0x7)
Reg 0x21. PCM/SPI Md - 0x38 (Res 0xfb)
Reg 0x22. PCM T St L - 0x0 (Res 0xff)
Reg 0x23. PCM T St H - 0x0 (Res 0x3)
Reg 0x24. PCM R St L - 0x0 (Res 0xff)
Reg 0x25. PCM R St H - 0x0 (Res 0x3)
Reg 0x26. T Gain 2 - 0x5 (Res 0x1f)
Reg 0x27. R Gain 2 - 0x3 (Res 0x1f)
Reg 0x28. T Gain 3 - 0x0 (Res 0x1f)
Reg 0x29. R Gain 3 - 0x0 (Res 0x1f)
Reg 0x2a. GCI Ctrl - 0x0 (Res 0xf)
Reg 0x2b. LV T Int - 0x0 (Res 0xff)
Reg 0x2c. LV T IntC - 0x0 (Res 0xf)
Reg 0x2d. Prg Hyb 1 - 0x0 (Res 0xff)
Reg 0x2e. Prg Hyb 2 - 0x0 (Res 0xff)
Reg 0x2f. Prg Hyb 3 - 0x0 (Res 0xff)
Reg 0x30. Prg Hyb 4 - 0x0 (Res 0xff)
Reg 0x31. Prg Hyb 5 - 0x0 (Res 0xff)
Reg 0x32. Prg Hyb 6 - 0x0 (Res 0xff)
Reg 0x33. Prg Hyb 7 - 0x0 (Res 0xff)
Reg 0x34. Prg Hyb 8 - 0x0 (Res 0xff)
Reg 0x35. Reserved - 0x0 (Res 0x0)
Reg 0x36. Reserved - 0x0 (Res 0x0)
Reg 0x37. Reserved - 0x0 (Res 0x0)
Reg 0x38. Reserved - 0xf (Res 0x0)
Reg 0x39. Reserved - 0x0 (Res 0x0)
Reg 0x3a. Reserved - 0x0 (Res 0x0)
Reg 0x3b. SQC - 0x0 (Res 0x50)
DAA Device Init completed
DAA init successful
bosMsgQCreate: Created message queue PSTN_CTL_EVQ at address 0x10002
BOS: Enter TaskCreate PSTN
BOS: TaskCreate - spawn new task PSTN
bcmOsTaskCreate:
TASK NAME = PSTN
TASK_PRIORITY = 0
BOS: Exit TaskCreate
pstnCtlInit successful
vrgendptCreate: capabilities.endptType = 0
ENDPT: 'HAPI_RM_OPEN_VHD_EVT' (0x80c1), hdl:0x30, op1:0x50, op2:0x1
ENDPT: hdspVhdOpen Primary Connection VHD success. VHD (0x50) of type: 0x0
ENDPT: 'HAPI_RM_OPEN_VHD_EVT' (0x80c1), hdl:0x30, op1:0x51, op2:0x1
ENDPT: hdspVhdOpen Endpt VHD success. VHD (0x51) of type: 0x2
ENDPT: TX Gain set to 1000
ENDPT: RX Gain set to 1000
ENDPT: 'HAPI_ECAN_STATE_EVT' (0x3ac0), hdl:0x0, op1:0x7, op2:0x0
boardHalCasGetDriver: chan = 0
Default value for provItemId '41' did not exist
ENDPT: Initialization completed successfully for endpt 0
vrgendptCreate: capabilities.endptType = 0
ENDPT: 'HAPI_RM_OPEN_VHD_EVT' (0x80c1), hdl:0x30, op1:0x52, op2:0x1
ENDPT: hdspVhdOpen Primary Connection VHD success. VHD (0x52) of type: 0x0
ENDPT: 'HAPI_RM_OPEN_VHD_EVT' (0x80c1), hdl:0x30, op1:0x53, op2:0x1
ENDPT: hdspVhdOpen Endpt VHD success. VHD (0x53) of type: 0x2
ENDPT: TX Gain set to 1000
ENDPT: RX Gain set to 1000
ENDPT: 'HAPI_ECAN_STATE_EVT' (0x3ac0), hdl:0x1, op1:0x7, op2:0x0
boardHalCasGetDriver: chan = 1
Default value for provItemId '41' did not exist
ENDPT: Initialization completed successfully for endpt 1
vrgendptCreate: capabilities.endptType = 1
ENDPT: 'HAPI_RM_OPEN_VHD_EVT' (0x80c1), hdl:0x30, op1:0x54, op2:0x1
ENDPT: hdspVhdOpen PSTN VHD success. VHD (0x54) of type: 0x6
ENDPT: TX Gain set to 1000
ENDPT: RX Gain set to 1000
ENDPT: 'HAPI_ECAN_STATE_EVT' (0x3ac0), hdl:0x2, op1:0x7, op2:0x0
Default value for provItemId '41' did not exist
ENDPT: Initialization completed successfully for endpt 2
00:00:44 Waiting for interface any to go up before proceeding with voice app...
DAA: Going OnHook
DAA: Going OnHook
00:00:44 EVENT: endpt 2, event ONHOOK, cnxid -1
app: echo 0 > /var/telephone2_status
br0: port 2(eth0) entering disabled state
br0: port 3(eth1) entering disabled state
br0: port 1(usb0) entering disabled state