Hello!
First off all I would like to appologize for my bad english.
kamikaze 8.09.1 (openwrt-brcm-2.4-squashfs.trx)
+
kmod-usb2_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-usb-core_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-usb-serial_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-usb-storage_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-usb-uhci_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-scsi-core_2.4.35.4-brcm-2.4-1_mipsel.ipk
kmod-scsi-generic_2.4.35.4-brcm-2.4-1_mipsel.ipk
chat_2.4.3-11.1_mipsel.ipk
comgt_0.32-1.1_mipsel.ipk
wifi - work
usb - work
3G (Huawei E220) - work
lan - not work
root@OpenWrt:~# lspci
00:00.0 FLASH memory: Broadcom Corporation Sentry5 Chipcommon I/O Controller (rev 03)
00:01.0 Ethernet controller: Broadcom Corporation Sentry5 Ethernet Controller (rev 03)
00:02.0 MIPS: Broadcom Corporation BCM3302 Sentry5 MIPS32 CPU (rev 03)
00:03.0 USB Controller: Broadcom Corporation Device 471a (rev 03)
00:03.1 USB Controller: Broadcom Corporation Device 471a (rev 03)
00:04.0 RAM memory: Broadcom Corporation Sentry5 DDR/SDR RAM Controller (rev 03)
00:05.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 03)
00:06.0 Network controller: Broadcom Corporation BCM47xx/53xx RoboSwitch Core (rev 03)root@OpenWrt:~# dmesg
CPU revision is: 00029029
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Linux version 2.4.35.4 (andy@stable-sandbox) (gcc version 3.4.6 (OpenWrt-2.0)) #12 Mon Jun 1 21:52:49 UTC 2009
Setting the PFC to its default value
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM5354 rev 3 at 240 MHz
Using 120.000 MHz high precision timer.
Calibrating delay loop... 237.56 BogoMIPS
Memory: 30468k/32768k available (1425k kernel code, 2300k reserved, 100k data, 84k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: no core
PCI: Fixing up bus 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:01.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1e:10:23:a4:fc
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x181cc9
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000bb000-0x00240000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x00240000-0x003f0000 : "rootfs_data"
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
diag: Router model not detected.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
jffs2.bbc: SIZE compression mode activated.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
SCSI subsystem driver Revision: 1.00
eth0.0: add 01:00:5e:00:00:01 mcast address to master interface
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device eth0.0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:05.0 to 64
PCI/DMA
wl0: wlc_attach: chiprev 3 coreunit 0 corerev 13 cccap 0x104007ea maccap 0x30482205 band 2.4G, phy_type 5 phy_rev 0 ana_rev 6
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.5
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 360 bytes per conntrack
SB USB20H init
SB COREREV: 2
SB USB20H resetting
USB20H fcr: 0x64
USB20H shim cr: 0x8f7
PCI: Setting latency timer of device 00:03.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
usb-ohci.c: usb-00:03.0, PCI device 14e4:471a
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
SB USB20H init
SB COREREV: 2
USB20H fcr: 0x64
USB20H shim cr: 0x8f7
PCI: Setting latency timer of device 00:03.1 to 64
ehci_hcd 00:03.1: PCI device 14e4:471a
ehci_hcd 00:03.1: irq 6, pci mem b8003800
usb.c: new USB bus registered, assigned bus number 2
ehci_hcd 00:03.1: illegal capability!
ehci_hcd 00:03.1: USB 0.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
hub.c: connect-debounce failed, port 1 disabled
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: new USB device 00:03.0-1, assigned address 2
usbserial.c: Generic converter detected
usbserial.c: Generic converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
usbserial.c: Generic converter detected
usbserial.c: Generic converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
usbserial.c: Generic converter detected
usbserial.c: Generic converter now attached to ttyUSB2 (or usb/tts/2 for devfs)
device wl0 entered promiscuous mode
wl0: attempt to add interface with same source address.
br-lan: port 2(wl0) entering learning state
br-lan: port 2(wl0) entering forwarding state
br-lan: topology change detected, propagatingroot@OpenWrt:~# ifconfig
br-lan Link encap:Ethernet HWaddr 00:1E:10:23:A4:FC
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4858 errors:0 dropped:0 overruns:0 frame:0
TX packets:5393 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:784082 (765.7 KiB) TX bytes:3774764 (3.5 MiB)
eth0 Link encap:Ethernet HWaddr 00:1E:10:23:A4:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:87 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:10687 (10.4 KiB)
Interrupt:4
eth0.0 Link encap:Ethernet HWaddr 00:1E:10:23:A4:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:87 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:10201 (9.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:318 (318.0 B) TX bytes:318 (318.0 B)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.123.31.175 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:3596 errors:0 dropped:0 overruns:0 frame:0
TX packets:3618 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2190302 (2.0 MiB) TX bytes:721326 (704.4 KiB)
wl0 Link encap:Ethernet HWaddr 00:1E:10:23:A4:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4857 errors:0 dropped:0 overruns:0 frame:81
TX packets:5475 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:852074 (832.1 KiB) TX bytes:3827869 (3.6 MiB)
Interrupt:2 Base address:0x5000On PC (lan) ping to 192.168.1.1 not response (wifi it's ok).
Help me ;-)
(Last edited by Irek on 10 Sep 2009, 07:34)