OpenWrt Forum Archive

Topic: MI424WR Upgrade

The content of this topic has been archived on 3 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Linux version 2.6.28.7 (heji@heji-desktop) (gcc version 4.3.3 (GCC) ) #2 Thu Feb 26 17:21:23 CST 2009
CPU: XScale-IXP42x Family [690541c1] revision 1 (ARMv5TE), cr=000039ff
CPU: VIVT data cache, VIVT instruction cache
Machine: Actiontec MI424WR
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c0209250, node_mem_map c4000000
  DMA zone: 128 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16256 pages, LIFO batch:3
  Normal zone: 128 pages used for memmap
  Normal zone: 16256 pages, LIFO batch:3
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 127688KB available (1852K code, 182K data, 96K init)
Calibrating delay loop... 532.48 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 480 bytes
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
pci 0000:00:0d.0: reg 20 io port: [0xfce0-0xfcff]
pci 0000:00:0d.0: supports D1 D2
pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0d.0: PME# disabled
pci 0000:00:0d.1: reg 20 io port: [0xfce0-0xfcff]
pci 0000:00:0d.1: supports D1 D2
pci 0000:00:0d.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0d.1: PME# disabled
pci 0000:00:0d.2: reg 10 32bit mmio: [0x000000-0x0000ff]
pci 0000:00:0d.2: supports D1 D2
pci 0000:00:0d.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0d.2: PME# disabled
pci 0000:00:0e.0: reg 10 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:0f.0: reg 10 io port: [0xaf0-0xaff]
pci 0000:00:0f.0: reg 14 io port: [0xa70-0xa7f]
pci 0000:00:0f.0: reg 18 io port: [0x1f0-0x1ff]
pci 0000:00:0f.0: reg 1c io port: [0x170-0x17f]
pci 0000:00:0f.0: reg 20 io port: [0xcc00-0xcc1f]
pci 0000:00:0f.0: reg 24 io port: [0x8c00-0x8cff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:0d.0: dmabounce: registered device
pci 0000:00:0d.1: dmabounce: registered device
pci 0000:00:0d.2: dmabounce: registered device
pci 0000:00:0e.0: dmabounce: registered device
pci 0000:00:0f.0: dmabounce: registered device
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
IXP4xx Queue Manager initialized.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 249
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
eth0: MII PHY 1 on NPE-C
eth0: MII PHY 2 on NPE-C
eth0: MII PHY 3 on NPE-C
eth0: MII PHY 4 on NPE-C
eth1: MII PHY 17 on NPE-B
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=128
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
5 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 5 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00060000 : "RedBoot"
0x00060000-0x00160000 : "linux"
0x00160000-0x00fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=480000, len=B60000 
0x00480000-0x00fe0000 : "rootfs_data"
0x00fe0000-0x00fff000 : "FIS directory"
0x00fff000-0x01000000 : "RedBoot config"
i2c /dev entries driver
IXP4xx Watchdog Timer: heartbeat 60 sec
Registered led device: moca-wan
Registered led device: power-alarm
Registered led device: power-ok
Registered led device: wireless
Registered led device: inet-down
Registered led device: inet-up
Registered led device: moca-lan
Registered led device: wan-alarm
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 96K
Please be patient, while OpenWrt loads ...
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
net eth0: firmware: requesting NPE-C
NPE-C: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-C: firmware functionality 0x5, revision 0x2:1
eth0: link down
device eth0 entered promiscuous mode
net eth1: firmware: requesting NPE-B
NPE-B: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-B: firmware functionality 0x2, revision 0x2:1
eth1: link down
eth1: link down
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
libata version 3.00 loaded.
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
Driver 'sd' needs updating - please use bus_type methods
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: enabling device 0000:00:0d.2 (0140 -> 0142)
ehci_hcd 0000:00:0d.2: EHCI Host Controller
ehci_hcd 0000:00:0d.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0d.2: irq 25, io mem 0x48010000
ehci_hcd 0000:00:0d.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
sata_via 0000:00:0f.0: version 2.4
PCI: enabling device 0000:00:0f.0 (0000 -> 0001)
sata_via 0000:00:0f.0: routed to hard irq line 7
sata_via 0000:00:0f.0: enabling SATA channel native mode (0xd1)
scsi0 : sata_via
scsi1 : sata_via
scsi2 : sata_via
ata1: SATA max UDMA/133 port i16@0x1460 bmdma 0x1440 irq 23
ata2: SATA max UDMA/133 port i16@0x1470 bmdma 0x1448 irq 23
ata3: PATA max UDMA/133 port i16@0x1480 bmdma 0x1450 irq 23
ata1: SATA link down (SStatus 0 SControl 310)
ata2: SATA link down (SStatus 0 SControl 310)
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
Micrel/Kendin KS8995 Ethernet switch SPI driver version 0.1.1
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:0d.0: UHCI Host Controller
uhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:0d.0: HCRESET not completed yet!
uhci_hcd 0000:00:0d.0: irq 25, io base 0x00001400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 0 ports detected
uhci_hcd 0000:00:0d.1: UHCI Host Controller
uhci_hcd 0000:00:0d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:0d.1: HCRESET not completed yet!
uhci_hcd 0000:00:0d.1: irq 25, io base 0x00001420
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 0 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
eth0: link up
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state

root@OpenWrt:~# df
Filesystem           1k-blocks      Used Available Use% Mounted on
rootfs                    3200      3200         0 100% /
/dev/root                 3200      3200         0 100% /rom
/dev/mtdblock3           11648       604     11044   5% /jffs
mini_fo:/jffs             3200      3200         0 100% /

root@OpenWrt:~# free
              total         used         free       shared      buffers
  Mem:       127872        15604       112268            0         1724
Swap:            0            0            0
Total:       127872        15604       112268

root@OpenWrt:~# lspci
00:0d.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:0d.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:0d.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
00:0e.0 Network controller: Atheros Communications, Inc. AR5416 802.11a/b/g/n Wireless PCI Adapter (rev 01)
00:0f.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID Controller (rev 50)
root@OpenWrt:~#

Hi there!

Mmmm.... nice to see this....

as I have a lot of those MI424WR.... I'm wondering.... the upgrade.... what exactly did you do?

- Changed the RAM chips? (to have 128MB) - any trace routing/wire-soldering?
- SATA, USB... added some sort of miniPCI card?

...or is this some "new version/model" of the mi424wr?

Would you mind sharing a little bit more information? pictures? wink

kind regards,
M.Culibrk

mculibrk wrote:

Hi there!

Mmmm.... nice to see this....

as I have a lot of those MI424WR.... I'm wondering.... the upgrade.... what exactly did you do?

- Changed the RAM chips? (to have 128MB) - any trace routing/wire-soldering?
- SATA, USB... added some sort of miniPCI card?

...or is this some "new version/model" of the mi424wr?

Would you mind sharing a little bit more information? pictures? wink

kind regards,
M.Culibrk

bump realy interesting news

....yeah, "nice to see" but the author is not responding in any way...
so, this could also be just a "myth"....  wink

The discussion might have continued from here.