i searched a lot to find the right way to do. I'm using a WRTG3G-2.4-squashfs.bin Firmware with my UMTS CARD. Actually i think the card is not supported yet i tried to fix it anyway.
I installed all steps descibed on http://josefsson.org/grisslan/internet.html. Also i changed the /etc/modules.d/60-usb-serial file and put in the Vendor ID from my card like that.
usbserial vendor=0xaf0 product=0x7001
But when i start ifup wan it comes:
ifconfig: SIOCGIFFLAGS: No such device
Can't open device ppp0.
wan(3g): Failed to set the PIN code.
root@OpenWrt:~#
My Card is an Option Model: GEO301
SNR: EE487732D2
IMEI: 356301010109553
FCC ID: NCM0GE0301
Firmware: 2.7.1.Hd
is it possible to make this run ?
root@OpenWrt:/etc# dmesg
CPU revision is: 00029007
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, linesize 16 bytes.
Linux version 2.4.34 (nbd@ds10) (gcc version 3.4.6 (OpenWrt-2.0)) #3 Sun Sep 30 20:33:21 CEST 2007
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM4712 rev 1 at 200 MHz
Using 100.000 MHz high precision timer.
Calibrating delay loop... 197.42 BogoMIPS
Memory: 14224k/16384k available (1462k kernel code, 2160k reserved, 100k data, 80k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:02.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1c:10:87:62:6f
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x2000,blocks=8
1: offset=0x10000,size=0x10000,blocks=63
Using word write method
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x121cc8
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000be400-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x001f0000-0x003f0000 : "rootfs_data"
sflash: found no supported devices
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 360 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 80k freed
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'Linksys WRT54G3G'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Probing device eth0: found!
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
jffs2.bbc: SIZE compression mode activated.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
device eth0.0 entered promiscuous mode
eth0.0: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: port 1(eth0.0) entering forwarding state
br-lan: topology change detected, propagating
PCI: Setting latency timer of device 00:01.0 to 64
wl0: Broadcom BCM4320 802.11 Wireless Controller 4.80.53.0
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus]
PCI: Enabling device 01:01.0 (0000 -> 0002)
Yenta ISA IRQ mask 0x06f8, PCI irq 2
Socket status: 30000820
cs: cb_alloc(bus 2): vendor 0x1131, device 0x1561
PCI: Enabling device 02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 00:04.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
usb-ohci.c: usb-00:04.0, PCI device 14e4:4716
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 02:00.0 to 64
usb-ohci.c: USB OHCI at membase 0xc01b5000, IRQ 2
usb-ohci.c: usb-02:00.0, PCI device 1131:1561
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
hub.c: new USB device 02:00.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0xaf0/0x7011) is not claimed by any active driver.
(Last edited by magglite on 10 Jan 2009, 21:53)