I am running KAMIKAZE (bleeding edge, r13003) on Netgear DG834gv2. The problem is that the PPP0 interface is not appearing on the ifconfig. My ISP uses PPPoE to connect.
Logread says:
Jan 1 00:51:27 OpenWrt daemon.warn pppd[1607]: Timeout waiting for PADO packets
Jan 1 00:51:27 OpenWrt daemon.err pppd[1607]: Unable to complete PPPoE Discovery
Jan 1 00:52:12 OpenWrt daemon.warn pppd[1607]: Timeout waiting for PADO packets
Jan 1 00:52:12 OpenWrt daemon.err pppd[1607]: Unable to complete PPPoE Discovery
Jan 1 00:52:57 OpenWrt daemon.warn pppd[1607]: Timeout waiting for PADO packets
Jan 1 00:52:57 OpenWrt daemon.err pppd[1607]: Unable to complete PPPoE Discovery
Here is my network config file:
root@OpenWrt:~# cat /etc/config/network
config 'interface' 'loopback'
option 'ifname' 'lo'
option 'proto' 'static'
option 'ipaddr' '127.0.0.1'
option 'netmask' '255.0.0.0'
config 'interface' 'lan'
option 'type' 'bridge'
option 'ifname' 'eth0'
option 'proto' 'static'
option 'netmask' '255.255.255.0'
option 'nat' '1'
option 'macaddr' ''
option 'ip6addr' ''
option 'gateway' ''
option 'ip6gw' ''
option 'ipaddr' '192.168.0.1'
config 'atm-bridge'
option 'unit' '0'
option 'payload' 'bridged'
config 'interface' 'wan'
option 'ifname' 'nas0'
option 'proto' 'pppoe'
option 'encaps' 'llc'
option 'vpi' '0'
option 'vci' '103'
option 'username' 'secret'
option 'password' 'secret'
option 'type' 'bridged'
option 'macaddr' ''
option 'mtu' ''
option 'keepalive' ''
option 'defaultroute' '1'
option 'ppp_redial' 'persist'
option 'ipaddr' ''
option 'ip6addr' ''
option 'netmask' ''
option 'gateway' ''
option 'ip6gw' ''Here is the dmesg output
root@OpenWrt:~# dmesg
Linux version 2.6.26.5 (travis@localhost.localdomain) (gcc version 4.1.2) #1 Sun Oct 19 01:33:42 CDT 2008
console [early0] enabled
CPU revision is: 00018448 (MIPS 4KEc)
Clocks: prediv: 1, postdiv: 1, mul: 10
TI AR7 (TNETD7300), ID: 0x0005, Revision: 0x02
Determined physical RAM map:
memory: 01000000 @ 14000000 (usable)
Entering add_active_range(0, 81920, 86016) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 81920 -> 86016
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 81920 -> 86016
On node 0 totalpages: 4096
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: init=/etc/preinit rootfstype=squashfs,jffs2, console=ttyS0,115200n8
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 12564k/16384k available (1998k kernel code, 3820k reserved, 420k data, 124k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 149.91 BogoMIPS (lpj=749568)
Mount-cache hash table entries: 512
net_namespace: 644 bytes
NET: Registered protocol family 16
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 24
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
console handover: boot [early0] -> real [ttyS0]
serial8250: ttyS1 at MMIO 0x8610f00 (irq = 16) is a TI-AR7
Fixed MDIO Bus: probed
cpmac-mii: probed
cpmac: device eth0 (regs: 08612800, irq: 41, phy: , mac: 00:0f:b5:c3:54:c1)
cpmac: device eth1 (regs: 08610000, irq: 27, phy: , mac: 00:0f:b5:c3:54:c0)
physmap platform flash device: 00800000 at 10000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
4 ar7part partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x00010000 : "loader"
0x003f0000-0x00400000 : "config"
0x00020000-0x003f0000 : "linux"
0x000e774b-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=1F0000, len=200000
0x001f0000-0x003f0000 : "rootfs_data"
ar7_wdt: disabling watchdog timer
ar7_wdt: timer margin 59 seconds (prescale 65535, change 57180, freq 62500000)
Registered led device: ppp
Registered led device: status
Registered led device: adsl
Registered led device: wifi
Registered led device: power
vlynq0: regs 0x08611800, irq 29, mem 0x04000000
vlynq0: using local clock divisor 8
Found a VLYNQ device: 00000009
vlynq1: regs 0x08611c00, irq 33, mem 0x0c000000
TCP vegas registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
PHY: 0:10 - Link is Down
NET: Registered protocol family 8
NET: Registered protocol family 20
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
registered device TI Avalanche SAR
Sangam detected
requesting firmware image "ar0700xx.bin"
firmware: requesting ar0700xx.bin
avsar firmware released
tn7dsl_set_modulation : Setting mode to 0x0
Creating new root folder avalanche in the proc for the driver stats
Texas Instruments ATM driver: version:[7.03.01.00]
ar7_wdt: enabling watchdog timer
NET: Registered protocol family 24
tn7atm_close: closing 0.0.103.5
tn7sar_teardown_complete called for channel 0
ChannelTeardown returned rc = 0
br-lan: port 1(eth0) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
br2684_create: register_netdev failed
tn7atm_close: closing 0.0.103.5
tn7sar_teardown_complete called for channel 0
ChannelTeardown returned rc = 0Here is lsmod
root@OpenWrt:~# lsmod
Module Size Used by Not tainted
br2684 7920 1
pppoe 11968 0
pppox 2288 1 pppoe
tiatm 151008 0
nf_nat_tftp 1088 0
nf_conntrack_tftp 3760 1 nf_nat_tftp
nf_nat_irc 1856 0
nf_conntrack_irc 4768 1 nf_nat_irc
nf_nat_ftp 2432 0
nf_conntrack_ftp 6880 1 nf_nat_ftp
ipt_MASQUERADE 2080 1
iptable_nat 4848 1
nf_nat 14624 5 nf_nat_tftp,nf_nat_irc,nf_nat_ftp,ipt_MASQUERADE,iptable_nat
xt_state 1600 6
nf_conntrack_ipv4 12064 9 iptable_nat,nf_nat
nf_conntrack 46704 11 nf_nat_tftp,nf_conntrack_tftp,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_state,nf_conntrack_ipv4
ipt_REJECT 3008 2
xt_TCPMSS 3936 1
ipt_LOG 6880 0
xt_multiport 2528 0
xt_mac 1312 0
xt_limit 2016 1
iptable_mangle 2080 0
iptable_filter 2080 1
ip_tables 10864 3 iptable_nat,iptable_mangle,iptable_filter
xt_tcpudp 2624 3
x_tables 11504 11 ipt_MASQUERADE,iptable_nat,xt_state,ipt_REJECT,xt_TCPMSS,ipt_LOG,xt_multiport,xt_mac,xt_limit,ip_tables,xt_tcpudp
ppp_async 10944 0
ppp_generic 26080 3 pppoe,pppox,ppp_async
slhc 5952 1 ppp_generic
crc_ccitt 1440 1 ppp_async
atm 48912 4 br2684,tiatmHere are the packages that i have installed
root@OpenWrt:~# opkg list_installed
base-files-ar7 - 13-r13003 -
br2684ctl - 20040226-1 -
bridge - 1.4-1 -
busybox - 1.11.2-1 -
dnsmasq - 2.45-1 -
dropbear - 0.51-2 -
firewall - 1-1 -
haserl - 0.9.24-1 -
hotplug2 - 0.9+r102-2 -
iptables - 1.4.0-1 -
iptables-mod-conntrack - 1.4.0-1 -
iptables-mod-nat - 1.4.0-1 -
kernel - 2.6.26.5-ar7-1 -
kmod-atm - 2.6.26.5-ar7-1 -
kmod-ipt-conntrack - 2.6.26.5-ar7-1 -
kmod-ipt-core - 2.6.26.5-ar7-1 -
kmod-ipt-nat - 2.6.26.5-ar7-1 -
kmod-ipt-nathelper - 2.6.26.5-ar7-1 -
kmod-ppp - 2.6.26.5-ar7-1 -
kmod-pppoe - 2.6.26.5-ar7-1 -
kmod-sangam-atm-annex-a - 2.6.26.5+D7.03.01.00-ar7-R2 -
libgcc - 4.1.2-13 -
libuci - 0.6.2-1 -
linux-atm - 2.4.1-1 -
mtd - 8 -
opkg - 4564-1 -
ppp - 2.4.3-10 -
ppp-mod-pppoe - 2.4.3-10 -
uci - 0.6.2-1 -
uclibc - 0.9.29-13 -
udevtrigger - 106-1 -
webif - 0.3-4520 -I have posted my problem on another thread but it has become quite cluttered so i decided to start a new one :-)
(Last edited by symbiansucks on 20 Oct 2008, 13:09)