Hello

i try to use kamikaze7.07 in Z-Com 3121P (xscale be arm platform, ixp425 intel processor)
with minipci device "AG-621" (Atheros AR5212A chip)

Almost all works good, but madwifi driver starts, i configure it, and device cannot see AP.
Or if configured as AP - cannot see by another devices (stations)

The range to AP - 5 meters (this is a Z-com XG580 Plus with factory firmware).
This AP associated if I upload to ixp425 device the factory firmware (instead my own compiled firmware with madwifi).

For clean experiments - i set both (AP and Station) to 1th channel (2.412 GHz)
Also i try to swap settings on ap an station - anyway nothing happens - on ixp425 device "cannot see" another device.

Also i have found Atheros PCI card, and install to my computer with UBUNTU linux - and madwifi driver work fine, as station, or as AP, and fine connect to Z-com XG580.
But "cannot see" ixp425 device too.

Also i mark contact as here: http://www.minipci.biz/pin7.jpg - (rfkill)
"No scan results" too

Here logs:

root@OpenWrt:/# dmesg
Linux version 2.6.21.6 (mib@mib) (gcc version 4.1.2) #13 Tue Aug 7 13:21:01 EEST 2007
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
Machine: Intel IXDP425 Development Platform
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 4096
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,9600 init=/etc/preinit
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 16MB = 16MB total
Memory: 14164KB available (1792K code, 167K data, 76K init)
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
PCI: bus0: Fast back to back transfers enabled
dmabounce: registered device 0000:00:01.0 on pci bus
Time: OSTS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Non-volatile memory driver v1.2
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
IXP4XX Q Manager 0.2.1 initialized.
IXP4XX NPE driver Version 0.3.0 initialized
ixp4xx_crypto 0.0.1 registered successfully
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=64
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x7e0000
7 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 7 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00060000 : "RedBoot"
0x00060000-0x00160000 : "kernel"
0x00160000-0x00780000 : "rootfs"
0x00260000-0x00780000 : "rootfs_data"
0x00780000-0x007c0000 : "unallocated"
0x007c0000-0x007c1000 : "RedBoot config"Also i mark contact as here: http://www.minipci.biz/pin7.jpg -
>>"No scanresults" too
0x007c1000-0x007c2000 : "Config backup"
mtd: partition "Config backup" doesn't start on an erase block boundary -- force read-only
0x007e0000-0x00800000 : "FIS directory"
i2c /dev entries driver
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP westwood registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
ixp4xx_mac driver 0.3.1: eth0 on NPE-B with PHY[0] initialized
ixp4xx_mac driver 0.3.1: eth1 on NPE-C with PHY[1] initialized
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 76K
Warning: unable to open an initial console.
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
eth0: NPE-B not running
eth0: NPE-B not running
eth0: NPE-B not running
eth0: NPE-B not running
wlan: 0.8.4.2 (svn r2568)
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, REGOPS_FUNC)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (svn r2568)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_pci: 0.9.4.5 (svn r2568)
PCI: enabling device 0000:00:01.0 (0340 -> 0342)
ath_pci: switching rfkill capability off
ath_pci: switching per-packet transmit power control off
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.6 phy 4.1 radio 3.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0x48000000, irq=28

root@OpenWrt:/# lsmod
Module                  Size  Used by    Tainted: P 
ath_pci                81896  0
wlan_xauth               448  0
wlan_wep                4064  0
wlan_tkip               9440  0
wlan_ccmp               5472  0
wlan_acl                1952  0
ath_rate_minstrel       7936  1
ath_hal               241240  3 ath_pci,ath_rate_minstrel
wlan_scan_sta           7968  1
wlan_scan_ap            2464  0
wlan                  155724  10 ath_pci,wlan_xauth,wlan_wep,wlan_tkip,wlan_ccmp,wlan_acl,ath_rate_minstrel,wlan_scan_sta,wlan_scan_ap

root@OpenWrt:/# wlanconfig ath0 destroy
root@OpenWrt:/# wlanconfig ath0 create wlandev wifi0 wlanmode sta
ath0
root@OpenWrt:/# ifconfig ath0 10.2.2.2 netmask 255.255.255.0 up
root@OpenWrt:/# iwconfig ath0 channel 1
root@OpenWrt:/# iwconfig ath0 essid "LIFE"

root@OpenWrt:/# ifconfig
ath0      Link encap:Ethernet  HWaddr 00:60:B3:C7:A1:A6 
          inet addr:10.2.2.2  Bcast:10.2.2.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wifi0     Link encap:UNSPEC  HWaddr 00-60-B3-C7-A1-A6-00-08-00-00-00-00-00-00-00-00 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:10430 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:199
          RX bytes:0 (0.0 B)  TX bytes:459410 (448.6 KiB)    (rx bytes 0.0 ???)
          Interrupt:28

root@OpenWrt:/# iwconfig ath0
ath0      IEEE 802.11a  ESSID:"LIFE"  Nickname:""
          Mode:Managed  Frequency:5.2 GHz  Access Point: Not-Associated   
          Bit Rate:0 kb/s   Tx-Power:17 dBm   Sensitivity=1/1 
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/70  Signal level=-256 dBm  Noise level=-256 dBm   <----- ???
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

root@OpenWrt:/# iwlist ath0 channel
ath0      46 channels in total; available frequencies :
          Channel 01 : 2.412 GHz
          Channel 02 : 2.417 GHz
          Channel 03 : 2.422 GHz
          Channel 04 : 2.427 GHz
          Channel 05 : 2.432 GHz
          Channel 06 : 2.437 GHz
          Channel 07 : 2.442 GHz
          Channel 08 : 2.447 GHz
          Channel 09 : 2.452 GHz
          Channel 10 : 2.457 GHz
          Channel 11 : 2.462 GHz
          Channel 36 : 5.18 GHz
          Channel 40 : 5.2 GHz
          Channel 42 : 5.21 GHz
          Channel 44 : 5.22 GHz
          Channel 48 : 5.24 GHz
          Channel 50 : 5.25 GHz
          Channel 52 : 5.26 GHz
          Channel 56 : 5.28 GHz
          Channel 58 : 5.29 GHz
          Channel 60 : 5.3 GHz
          Channel 64 : 5.32 GHz
          Channel 149 : 5.745 GHz
          Channel 152 : 5.76 GHz
          Channel 153 : 5.765 GHz
          Channel 157 : 5.785 GHz
          Channel 160 : 5.8 GHz
          Channel 161 : 5.805 GHz
          Channel 165 : 5.825 GHz
          Current Frequency:2.437 GHz (Channel 6)

root@OpenWrt:/# wlanconfig ath0 list active
Channel   1 : 2412  Mhz 11g          Channel  48 : 5240  Mhz 11a Dynamic 
Channel   2 : 2417  Mhz 11g          Channel  50 : 5250  Mhz 11a Static   
Channel   3 : 2422  Mhz 11g          Channel  52 : 5260  Mhz 11a         
Channel   4 : 2427  Mhz 11g          Channel  56 : 5280  Mhz 11a Dynamic 
Channel   5 : 2432  Mhz 11g          Channel  58 : 5290  Mhz 11a Static   
Channel   6 : 2437  Mhz 11g Dynamic  Channel  60 : 5300  Mhz 11a         
Channel   7 : 2442  Mhz 11g          Channel  64 : 5320  Mhz 11a         
Channel   8 : 2447  Mhz 11g          Channel 149 : 5745  Mhz 11a         
Channel   9 : 2452  Mhz 11g          Channel 152 : 5760  Mhz 11a Static   
Channel  10 : 2457  Mhz 11g          Channel 153 : 5765  Mhz 11a Dynamic 
Channel  11 : 2462  Mhz 11g          Channel 157 : 5785  Mhz 11a         
Channel  36 : 5180  Mhz 11a          Channel 160 : 5800  Mhz 11a Static   
Channel  40 : 5200  Mhz 11a Dynamic  Channel 161 : 5805  Mhz 11a Dynamic 
Channel  42 : 5210  Mhz 11a Static   Channel 165 : 5825  Mhz 11a         
Channel  44 : 5220  Mhz 11a         

root@OpenWrt:/# iwlist ath0 scan
ath0      No scan results

I think, rf part does not work (not receive signal) with madwifi on ixp 425, why ?

also i remove 200-no_debug.patch from ./package/madwifi/patches and compile madwifi with athdebug tool
root@OpenWrt:/# athdebug 0xffffffff
dev.wifi0.debug: 0x00000000 => 0xffffffff<xmit,xmit_desc,recv,recv_desc,rate,reset,mode,beacon,watchdog,intr,xmit_proc,recv_proc,beacon_proc,calibrate,keycach>
Details:
        xmit + 0x00000001 - transmission of packets before out to HW
   xmit_desc + 0x00000002 - transmit descriptors
        recv + 0x00000004 - received packets directly from HW
   recv_desc + 0x00000008 - recv descriptors
        rate + 0x00000010 - rate control modules
       reset + 0x00000020 - reset processing and initialization
        mode + 0x00000040 - mode initialization and changes
      beacon + 0x00000080 - beacon handling
    watchdog + 0x00000100 - watchdog timer
        intr + 0x00001000 - interrupt processing
   xmit_proc + 0x00002000 - processing of transmit descriptors
   recv_proc + 0x00004000 - processing of receive descriptors
beacon_proc + 0x00008000 - beacon processing
   calibrate + 0x00010000 - periodic re-calibration
    keycache + 0x00020000 - key cache management
       state + 0x00040000 - 802.11 state transitions
        node + 0x00080000 - node management
         led + 0x00100000 - led management
          ff + 0x00200000 - fast frame handling
       turbo + 0x00400000 - dynamic turbo handling
       uapsd + 0x00800000 - WME/UAPSD handling
        doth + 0x01000000 - 802.11h handling
       fatal + 0x80000000 - fatal errors

root@OpenWrt:/# wlanconfig ath0 create wlandev wifi0 wlanmode sta
ath_rate_minstrel: ath_rate_ctl_reset 00:00:00:00:00:00 no rates (fixed -1)
ath_node_alloc: an c0373800
ath0

root@OpenWrt:/# ifconfig ath0 10.2.2.2 netmask 255.255.255.0 up
ath_init: mode 1
ath_stop_locked: invalid 0 flags 0x1002
ath_startrecv: mtu 1500 cachelsz 32 rxbufsize 3104
ath_mode_init: RX filter 0x17, MC filter 00000000:00000000
ath_mode_init: RX filter 0x117, MC filter 00000000:00000000
ath_newstate: wifi0: INIT -> SCAN
ath_newstate: RX filter 0x117 bssid 00:00:00:00:00:00 aid 0x0
ath_scan_start: RX filter 0x117 bssid ff:ff:ff:ff:ff:ff aid 0
ath_chan_set: 6 (2437 MHz) -> 1 (2412 MHz)
ath_draintxq: beacon queue 0x0
ath_tx_stopdma: tx queue [0] 0x0, link 00000000
ath_tx_stopdma: tx queue [1] 0x0, link 00000000
ath_tx_stopdma: tx queue [2] 0x0, link 00000000
ath_tx_stopdma: tx queue [3] 0x0, link 00000000
ath_tx_stopdma: tx queue [4] 0x0, link 00000000
ath_tx_stopdma: tx queue [7] 0x0, link 00000000
ath_tx_stopdma: tx queue [8] 0x0, link 00000000
ath_stoprecv: rx queue 0x997300, link ffc10ea0
R (ffc10000 997000) 00997060 00a79020 00000000 00000c40 11fd0045 3db90003 *
R (ffc10060 997060) 009970c0 00a78020 00000000 00000c40 122d0045 4dba0003 *
R (ffc100c0 9970c0) 00997120 00967020 00000000 00000c40 120d0045 5dba0003 *
R (ffc10120 997120) 00997180 00966020 00000000 00000c40 125d0045 6dba0003 *
R (ffc10180 997180) 009971e0 00965020 00000000 00000c40 121d0045 7dba0003 *
R (ffc101e0 9971e0) 00997240 00964020 00000000 00000c40 122d0045 0dba0005 !
R (ffc10240 997240) 009972a0 009e3020 00000000 00000c40 121d0045 1dbb0003 *
R (ffc102a0 9972a0) 00997300 009e2020 00000000 00000c40 122d0045 2dbb0003 *
R (ffc10300 997300) 00997360 008dd020 00000000 00000c40 00000000 00000000 
<skiped>
ath_startrecv: mtu 1500 cachelsz 32 rxbufsize 3104
ath_mode_init: RX filter 0x17, MC filter 00000000:00000000
ath_tx_start: skb c08e3820 [data c084ee10 len 42] skbaddr 84ee10
NODS 00:60:b3:c7:a1:a6->ff:ff:ff:ff:ff:ff(ff:ff:ff:ff:ff:ff) probe_req 1M

40 00 00 00 ff ff ff ff  ff ff 00 60 b3 c7 a1 a6 
ff ff ff ff ff ff 00 00  00 00 01 08 82 84 8b 96 
0c 12 18 24 32 04 30 48  60 6c

ath_tx_start: Q1: (ds)ffc1a480 (lk)00000000 (d)0084ee10 (c0)0336002e (c1)0700002a 000b0000 0000001b
ath_tx_txqaddbuf: txq depth = 1
ath_tx_txqaddbuf: TXDP[1] = 9f9480 (ffc1a480)
ath_mode_init: RX filter 0x117, MC filter 00000000:00000000
ath_mode_init: RX filter 0x117, MC filter 00000000:00000040
ath_mode_init: RX filter 0x117, MC filter 00000000:00000040
ath_chan_set: 1 (2412 MHz) -> 6 (2437 MHz)
ath_draintxq: beacon queue 0x0
ath_tx_stopdma: tx queue [0] 0x0, link 00000000
ath_tx_stopdma: tx queue [1] 0x9f9480, link ffc1a480
ath_tx_stopdma: tx queue [2] 0x0, link 00000000
ath_tx_stopdma: tx queue [3] 0x0, link 00000000
ath_tx_stopdma: tx queue [4] 0x0, link 00000000
ath_tx_stopdma: tx queue [7] 0x0, link 00000000
ath_tx_stopdma: tx queue [8] 0x0, link 00000000
T (ffc1a480 9f9480) 00000000 0084ee10 0336002e 0700002a 000b0000 0000001b 02f40001 00086001 *
ath_stoprecv: rx queue 0x997540, link ffc10ea0
R (ffc10000 997000) 00997060 00a79020 00000000 00000c40 237d0045 3dc60003 *
R (ffc10060 997060) 009970c0 00a78020 00000000 00000c40 237d0045 4dc60003 *
R (ffc100c0 9970c0) 00997120 00967020 00000000 00000c40 142d0045 5dc60003 *
R (ffc10120 997120) 00997180 00966020 00000000 00000c40 141d0045 6dc70003 *
R (ffc10180 997180) 009971e0 00965020 00000000 00000c40 23dd0045 7dc70003 *
R (ffc101e0 9971e0) 00997240 00964020 00000000 00000c40 143d0045 0dc70003 *
R (ffc10240 997240) 009972a0 009e3020 00000000 00000c40 141d0037 54440003 *
R (ffc102a0 9972a0) 00997300 009e2020 00000000 00000c40 14ad0045 1dc80003 *
R (ffc10300 997300) 00997360 008dd020 00000000 00000c40 145d0045 2dc80003 *
R (ffc10360 997360) 009973c0 008d1020 00000000 00000c40 147d0045 3dc80003 *
R (ffc103c0 9973c0) 00997420 00fb2020 00000000 00000c40 23cd0045 4dc90003 *
R (ffc10420 997420) 00997480 00a06020 00000000 00000c40 144d0045 5dc90003 *
R (ffc10480 997480) 009974e0 00a05020 00000000 00000c40 237d0045 6dc90003 *
R (ffc104e0 9974e0) 00997540 00a04020 00000000 00000c40 142d0045 7dca0003 *
R (ffc10540 997540) 009975a0 00a03020 00000000 00000c40 00000000 00000000 
etc etc etc,
maybe this fatals make hints ?

If the additional information is necessary to solve my problem - write about it please.

List problems because of which, the driver can work, but not see an AP or stations ?

On this device 2 mini-pci a socket.
I have replaced wifi device in other socket - and it has completely worked!!!
At loading there are differences:
wlan: 0.8.4.2 (svn r2568)
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, REGOPS_FUNC)
ath_rate_sample: 1.2 (svn r2568)
ath_pci: 0.9.4.5 (svn r2568)
PCI: enabling device 0000:00:02.0 (0340 -> 0342)  <---- instead  0000:00:01.0
ath_pci: switching rfkill capability off
ath_pci: switching per-packet transmit power control off
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.6 phy 4.1 radio 3.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0x48000000, irq=27  <--instead   irq=28

root@OpenWrt:/# iwlist ath0 scan
ath0      Scan completed :
          Cell 01 - Address: 00:60:B3:8E:40:94
                    ESSID:"LIFE"
                    Mode:Master
                    Frequency:2.412 GHz (Channel 1)
                    Quality=71/70  Signal level=-24 dBm  Noise level=-95 dBm
                    Encryption key:off
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
YEAP!!!

(Last edited by J-Nox on 16 Aug 2007, 13:01)