Hello all!
I just installed Lede 17.01.0 from this page https://lede-project.org/toh/hwdata/zyxel/zyxel_omni to my old Zyxel Keenetic Omni like this, but after device rebooted ehternet ports are not working.
I can connect to device via serial port and configure Wifi to Enable state. Now I can connect to router by ssh or http via wifi, but can't via ethernet. No one port (WAN or any one LAN) not working. Link leds are flashing right, in switch configuration I can see link status of ethernet ports. But them not working.
Al so not work odhcpd, I can't get IP addres via DHCP on wifi too. Only static address on clients.
my current dmesg output
[ 0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ZyXEL Keenetic Omni
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8035a4b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007fef0
[ 0.000000] Readback ErrCtl register=0007fef0
[ 0.000000] Memory: 60960K/65536K available (3012K kernel code, 144K rwdata, 384K rodata, 164K init, 208K bss, 4576K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015453] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080605] pid_max: default: 32768 minimum: 301
[ 0.089917] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102939] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122070] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.141595] pinctrl core: initialized pinctrl subsystem
[ 0.153127] NET: Registered protocol family 16
[ 0.178982] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.189998] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.203579] clocksource: Switched to clocksource systick
[ 0.215246] NET: Registered protocol family 2
[ 0.224808] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.238581] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.251170] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.263889] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.275428] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.288123] NET: Registered protocol family 1
[ 0.296703] PCI: CLS 0 bytes, default 32
[ 0.300443] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.313057] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.325148] Crashlog allocated RAM at address 0x3f00000
[ 0.351157] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.362663] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.384694] io scheduler noop registered
[ 0.392335] io scheduler deadline registered (default)
[ 0.402812] ralink-usb-phy usbphy: invalid resource
[ 0.412952] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.428935] console [ttyS0] disabled
[ 0.435975] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.455652] console [ttyS0] enabled
[ 0.469471] bootconsole [early0] disabled
[ 0.491759] spi spi0.0: force spi mode3
[ 0.499987] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.509603] 4 ofpart partitions found on MTD device spi0.0
[ 0.520534] Creating 4 MTD partitions on "spi0.0":
[ 0.530099] 0x000000000000-0x000000030000 : "u-boot"
[ 0.541751] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.554251] 0x000000040000-0x000000050000 : "factory"
[ 0.566155] 0x000000050000-0x000000800000 : "firmware"
[ 1.226105] 2 uimage-fw partitions found on MTD device firmware
[ 1.237939] 0x000000050000-0x000000178070 : "kernel"
[ 1.249452] 0x000000178070-0x000000800000 : "rootfs"
[ 1.261139] mtd: device 5 (rootfs) set to be root filesystem
[ 1.272613] 1 squashfs-split partitions found on MTD device rootfs
[ 1.284945] 0x0000003c3000-0x000000800000 : "rootfs_data"
[ 1.300293] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex)
[ 1.318739] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.331335] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.348344] rt2880_wdt 10000120.watchdog: Initialized
[ 1.359840] NET: Registered protocol family 10
[ 1.373073] NET: Registered protocol family 17
[ 1.382073] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.407218] 8021q: 802.1Q VLAN Support v1.8
[ 1.429907] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.444903] Freeing unused kernel memory: 164K (80377000 - 803a0000)
[ 3.932238] init: Console is alive
[ 3.939348] init: - watchdog -
[ 5.676547] usbcore: registered new interface driver usbfs
[ 5.687630] usbcore: registered new interface driver hub
[ 5.698342] usbcore: registered new device driver usb
[ 5.714274] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.728609] ehci-platform: EHCI generic platform driver
[ 5.749364] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.761166] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.770049] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.781542] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.797456] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.814662] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.828251] hub 1-0:1.0: USB hub found
[ 5.836131] hub 1-0:1.0: 1 port detected
[ 5.846724] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.860351] ohci-platform: OHCI generic platform driver
[ 5.871076] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 5.884670] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 5.900539] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 5.935585] hub 2-0:1.0: USB hub found
[ 5.943527] hub 2-0:1.0: 1 port detected
[ 5.953031] leds-gpio: probe of gpio-leds failed with error -2
[ 5.969212] init: - preinit -
[ 6.974211] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.189084] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 8.206790] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.333862] procd: - early -
[ 8.339775] procd: - watchdog -
[ 8.686529] procd: - ubus -
[ 8.904144] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 8.922957] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 8.941380] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 8.959382] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 8.980835] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 8.998820] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 9.016887] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 9.034957] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 9.053228] procd: - init -
[ 9.469634] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.490213] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 9.505364] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 9.573958] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.594155] nf_conntrack version 0.5.0 (955 buckets, 3820 max)
[ 9.649121] xt_time: kernel timezone is -0000
[ 9.669739] PPP generic driver version 2.4.2
[ 9.681097] NET: Registered protocol family 24
[ 9.707171] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 9.721644] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[ 9.737093] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 9.751459] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.057603] random: jshn: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 11.138904] random: jshn: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 17.186726] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 17.246222] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 17.259478] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 21.135623] 8021q: adding VLAN 0 to HW filter on device eth0
[ 21.203056] device eth0.2 entered promiscuous mode
[ 21.212684] device eth0 entered promiscuous mode
[ 21.312323] br-lan: port 1(eth0.2) entered forwarding state
[ 21.323527] br-lan: port 1(eth0.2) entered forwarding state
[ 23.313689] br-lan: port 1(eth0.2) entered forwarding state
[ 76.533727] random: nonblocking pool is initialized
[ 89.088850] done.
[ 89.092729] jffs2: notice: (868) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 138.102756] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 138.115464] br-lan: port 1(eth0.2) entered disabled state
[ 138.762787] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[ 138.778668] br-lan: port 1(eth0.2) entered forwarding state
[ 138.789838] br-lan: port 1(eth0.2) entered forwarding state
[ 139.648789] br-lan: port 1(eth0.2) entered forwarding state
[ 148.470667] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 148.487137] device wlan0 entered promiscuous mode
[ 148.511147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 148.524028] br-lan: port 2(wlan0) entered forwarding state
[ 148.535045] br-lan: port 2(wlan0) entered forwarding state
[ 149.300595] br-lan: port 2(wlan0) entered forwarding state
[ 152.066459] device wlan0 left promiscuous mode
[ 152.075487] br-lan: port 2(wlan0) entered disabled state
[ 152.537419] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 152.553714] device wlan0 entered promiscuous mode
[ 152.563252] br-lan: port 2(wlan0) entered forwarding state
[ 152.574237] br-lan: port 2(wlan0) entered forwarding state
[ 152.602496] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 153.346698] br-lan: port 2(wlan0) entered forwarding state
~# ifconfig
br-lan Link encap:Ethernet HWaddr EC:43:F6:D7:30:0E
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fd02:3b82:5bae::1/60 Scope:Global
inet6 addr: fe80::ee43:f6ff:fed7:300e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:883 errors:0 dropped:0 overruns:0 frame:0
TX packets:180 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:196041 (191.4 KiB) TX bytes:31759 (31.0 KiB)
eth0 Link encap:Ethernet HWaddr EC:43:F6:D7:30:0E
inet6 addr: fe80::ee43:f6ff:fed7:300e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:334 errors:0 dropped:0 overruns:0 frame:0
TX packets:1120 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:34628 (33.8 KiB) TX bytes:317565 (310.1 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr EC:43:F6:D7:30:0F
inet6 addr: fe80::ee43:f6ff:fed7:300f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:356 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:114443 (111.7 KiB)
eth0.2 Link encap:Ethernet HWaddr EC:43:F6:D7:30:0E
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:750 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:195997 (191.4 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:727 errors:0 dropped:0 overruns:0 frame:0
TX packets:727 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:47584 (46.4 KiB) TX bytes:47584 (46.4 KiB)
wlan0 Link encap:Ethernet HWaddr EC:43:F6:D7:30:0E
inet6 addr: fe80::ee43:f6ff:fed7:300e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:882 errors:0 dropped:0 overruns:0 frame:0
TX packets:905 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:208383 (203.4 KiB) TX bytes:241456 (235.7 KiB)