I have ZBT-Z800AX with quactel 5g modem i reinstalled the official firmware from zbt and now modem doesn't work.
i've done echo "2c7c 0801" >/sys/bus/usb/dri
vers/qmi_wwan/new_id but unsure what to do here is this
Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2c7c ProdID=0801 Rev= 5.04
S: Manufacturer=Quectel
S: Product=RM520N-GL
S: SerialNumber=876e386e
C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#=12 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#=13 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
anyone have a clue?
do you have any log before openwrt? try to flash the same.
you flashed the modem, find the right firmware to flash back
And this is relevant for OpenWrt because?
sorry if its not allowed. Just can't figure this out
okay i'll ask them about it
It's not about allowed or not as far as I am concerned - it's about directing questions to those who can answer them
the modem is
Quectel RM520N-GL if that helps i'm sure it's to do with AT commands who do i ask about this?
don't ask me about that i'm not an expert at all of 4g/lte modems drivers and config
sorry that was for the other dude i clicked reply to him tho
the modem is
Quectel RM520N-GL if that helps i'm sure it's to do with AT commands who do i ask about this?
Which firmware do you have? The vendor sends me the firmware; if you want to try it, let me know.
Please get in contact with ZBT then.