[ 0.000000] Linux version 4.4.92 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3101-bce140e) ) #0 Tue Oct 17 14:59:45 2017
[ 0.000000] MyLoader: sysp=95fcfcd3, boardp=9fe0f7fd, parts=7f33ddd3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803d04d0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=SR3200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125328K/131072K available (3076K kernel code, 160K rwdata, 412K rodata, 312K init, 205K bss, 5744K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008207] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.071017] pid_max: default: 32768 minimum: 301
[ 0.075981] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082958] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092339] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.102743] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.110076] NET: Registered protocol family 16
[ 0.115886] MIPS: machine is YunCore SR3200
[ 0.339434] registering PCI controller with io_map_base unset
[ 0.345820] Can't analyze schedule() prologue at 800670fc
[ 0.359407] PCI host bridge to bus 0000:00
[ 0.363731] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.371013] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.376883] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.384043] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.392421] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 0.392448] pci 0000:00:00.0: invalid calibration data
[ 0.397898] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.397950] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.398008] pci 0000:00:00.0: supports D1
[ 0.398020] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.398198] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.398226] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.405937] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.413579] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.419392] clocksource: Switched to clocksource MIPS
[ 0.425654] NET: Registered protocol family 2
[ 0.430999] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.438353] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.445098] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.451880] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.458041] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.464882] NET: Registered protocol family 1
[ 0.469532] PCI: CLS 0 bytes, default 32
[ 0.473113] Crashlog allocated RAM at address 0x3f00000
[ 0.490471] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.496614] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.508955] io scheduler noop registered
[ 0.513129] io scheduler deadline registered (default)
[ 0.518715] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.527634] console [ttyS0] disabled
[ 0.551487] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.560578] console [ttyS0] enabled
[ 0.568120] bootconsole [early0] disabled
[ 0.580835] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.586423] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.591340] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.597446] Creating 4 MTD partitions on "spi0.0":
[ 0.602419] 0x000000000000-0x000000040000 : "u-boot"
[ 0.609333] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.616156] 0x000000050000-0x000000ff0000 : "firmware"
[ 0.648499] 2 uimage-fw partitions found on MTD device firmware
[ 0.654644] 0x000000050000-0x000000190000 : "kernel"
[ 0.660872] 0x000000190000-0x000000ff0000 : "rootfs"
[ 0.667274] mtd: device 4 (rootfs) set to be root filesystem
[ 0.673201] 1 squashfs-split partitions found on MTD device rootfs
[ 0.679595] 0x000000410000-0x000000ff0000 : "rootfs_data"
[ 0.686525] 0x000000ff0000-0x000001000000 : "art"
[ 0.704967] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 1.366103] libphy: ag71xx_mdio: probed
[ 1.961011] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.972509] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII
[ 1.980299] NET: Registered protocol family 10
[ 1.987651] NET: Registered protocol family 17
[ 1.992348] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.005469] 8021q: 802.1Q VLAN Support v1.8
[ 2.015795] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.024822] Freeing unused kernel memory: 312K
[ 2.848482] init: Console is alive
[ 2.852228] init: - watchdog -
[ 3.778553] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.807314] usbcore: registered new interface driver usbfs
[ 3.813107] usbcore: registered new interface driver hub
[ 3.818665] usbcore: registered new device driver usb
[ 3.828069] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.836016] ehci-platform: EHCI generic platform driver
[ 3.841547] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.847699] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.858147] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.879427] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 3.886816] hub 1-0:1.0: USB hub found
[ 3.891002] hub 1-0:1.0: 1 port detected
[ 3.895357] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.901548] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.912001] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.929412] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 3.936753] hub 2-0:1.0: USB hub found
[ 3.940972] hub 2-0:1.0: 1 port detected
[ 3.945684] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.963542] init: - preinit -
[ 4.778803] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.803606] random: procd: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[ 6.140996] eth0: link up (1000Mbps/Full duplex)
[ 6.145969] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.160057] jffs2: notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.179904] mount_root: switching to jffs2 overlay
[ 8.197130] urandom-seed: Seeding with /etc/urandom.seed
[ 8.313713] eth0: link down
[ 8.333222] procd: - early -
[ 8.336277] procd: - watchdog -
[ 8.941929] procd: - watchdog -
[ 8.945396] procd: - ubus -
[ 9.045464] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.057028] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.066734] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.076075] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.085685] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.095024] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.104831] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.114282] random: ubusd: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 9.123922] procd: - init -
[ 9.675141] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.687931] l2tp_core: L2TP core driver, V2.0
[ 9.693864] l2tp_netlink: L2TP netlink interface
[ 9.713925] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.727987] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 9.736304] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 9.921042] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 9.927052] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 10.144363] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 10.155457] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 10.338989] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 10.541468] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[ 10.551037] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 10.564038] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00016 api 5 features no-p2p,raw-mode,mfp crc32 0c5668f8
[ 10.575026] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 10.585821] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 10.665054] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 10.686295] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 11.890267] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 12.002831] ath: EEPROM regdomain: 0x0
[ 12.002847] ath: EEPROM indicates default country code should be used
[ 12.002854] ath: doing EEPROM country->regdmn map search
[ 12.002870] ath: country maps to regdmn code: 0x3a
[ 12.002878] ath: Country alpha2 being used: US
[ 12.002885] ath: Regpair used: 0x3a
[ 12.137875] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.150182] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
[ 12.191259] xt_time: kernel timezone is -0000
[ 12.257363] PPP generic driver version 2.4.2
[ 12.263838] NET: Registered protocol family 24
[ 12.283697] ath: EEPROM regdomain: 0x0
[ 12.283713] ath: EEPROM indicates default country code should be used
[ 12.283720] ath: doing EEPROM country->regdmn map search
[ 12.283737] ath: country maps to regdmn code: 0x3a
[ 12.283745] ath: Country alpha2 being used: US
[ 12.283752] ath: Regpair used: 0x3a
[ 12.293467] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 12.298299] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47
[ 12.325071] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 12.409032] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.243626] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 19.977774] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.993334] device eth0.1 entered promiscuous mode
[ 19.998286] device eth0 entered promiscuous mode
[ 20.025934] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.067666] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 20.287596] eth0: link up (1000Mbps/Full duplex)
[ 20.320065] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.367403] br-lan: port 1(eth0.1) entered forwarding state
[ 20.373242] br-lan: port 1(eth0.1) entered forwarding state
[ 20.379072] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 20.483508] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.246217] ath10k_pci 0000:00:00.0: DFS region 0x0 not supported, will trigger radar for every pulse
[ 22.369449] br-lan: port 1(eth0.1) entered forwarding state
[ 24.876265] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.892953] device wlan0 entered promiscuous mode
[ 25.342533] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 25.349658] br-lan: port 2(wlan0) entered forwarding state
[ 25.355355] br-lan: port 2(wlan0) entered forwarding state
[ 27.349533] br-lan: port 2(wlan0) entered forwarding state
[ 46.009259] random: nonblocking pool is initialized
I'm aware of:
[ 10.144363] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
and
[ 10.575026] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2