Xiaomi WiFi Router 3G

Yes, I released the rest buton right after led started blinking yellow.
Bot now I have done it 2nd time exactly the same and it worked :slight_smile:
On LEDE at the moment and trying to make my Huawei 3372 hilink to work :slight_smile:

Hey. I used this firmware back in december but 2.4 Wifi was really low range and it was always crashing, disconnecting devices. Is this firmware good now with wireless stability and overal stability? Thanks.

Hello, thank you very much for answering, as I told you, I did the process, updating without problems, the current situation is: I can enter by failsafe mode ethernet, putting a 192.168.1.x address I can enter by ssh but all in read mode .
if I enter by common mode, I have internet, and dhcp but I do not have access by web or by SSH. Will there be any way to enable the luci (web) being in safe?
thanks I await solutions.

Hello, I did the whole process, when I try step 15 it does not enter.
I can only enter via failsafe mode (via ssh) and only read mode
If the computer starts normally it gives me IP via dhcp and raises an internet connection, but I can not enter via SSH or telnet or anything, everything says REFUSE CONECTION.
some help?
Thank you

Have you found a fix to the random freezes? I'm start thinking that we have a faulty unit...

The system does not see the hard drive in the docking station. On the PC is determined without problems. Docking station Maiwo K308 on the chipset JMS567. On my second LinkSys EA6350 router, the docking station with a hard drive is determined correctly. Is there any idea how to solve the problem?
dmesg

[   20.792019] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   21.417722] random: crng init done
[   21.501727] pppoe-wan: renamed from ppp0
[   21.756351] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   33.215174] scsi 0:0:0:0: tag#0 uas_eh_abort_handler 0 uas-tag 1 inflight: CM                                                                                                                                                             D IN
[   33.222740] scsi 0:0:0:0: tag#0 CDB: opcode=0x12 12 00 00 00 24 00
[   33.229041] xhci-mtk 1e1c0000.xhci: Mismatch between completed Set TR Deq Ptr                                                                                                                                                              command & xHCI internal state.
[   33.238831] xhci-mtk 1e1c0000.xhci: ep deq seg = 8f038800, deq ptr = af060010
[   34.305150] scsi host0: uas_eh_device_reset_handler FAILED to get lock err -1                                                                                                                                                             6
[   34.312368] scsi 0:0:0:0: Device offlined - not ready after error recovery

lsusb

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 152d:0567 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

lsusb -t

/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/1p, 5000M
    |__ Port 1: Dev 2, If 0, Class=Mass Storage, Driver=uas, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/2p, 480M

In failsafe check /etc/config/beardrop
I'm pretty sure it's corrupt as mine was.

it should be:

config dropbear
	option PasswordAuth 'on'
	option RootPasswordAuth 'on'
	option Port '22'

Hi,

Currently I cannot access the ssh.bin the web service is down, I assume only temporary?

I have flashed the the dev bin Ok, currently running 2.25.122 according the the web ui

For me i had to replace the "http" with "https" on every new request to fix this problem...

thanks, getting there now.

Yes, have a root shell

:smiley:

um I have openwrt-ramips-mt7621-mir3g-squashfs-kernel1.bin and not lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1

does it matter? if so where is the lede bin?

Hmmm I have no web ui. I thought it might be a clash between my existing asus RT68U wifi unit and openwrt's choice on the xiaomi 3g of 192.168.1.1 so I ssh'd in and changed the network to 192.168.31.0 and 31.1 I can ssh into the xiaomi OK but there is no web ui on 192.168.31.1 so what can I do about this?

thanks

LEDE is now OpenWRT!

Snapshot builds did not include LUCI web interface.

opkg update
opkg install luci

Ah ok, so I have the wrong build? is there a stable build I should be on?

I

ah that worked perfectly thankyou, i have web ui and am logged in....time for bed I think....thanks for your help.

:slight_smile:

Its a random reboot. Problem persists.
It worked fine in stock rom.

Hi Flipz, is this a reply to me? ie openwrt isnt stable on the xiaomi 3g hence its only available in the developer branch?

And have you been able to solve it?
as?

So again have problems with usb. Usb2 (active hub, modem, hdd, usb stick) only and 5G radio only enabled.

On modem I have regular down/up of eth1 and hdd is visible after restart (power off/on on hdd) and after time stops. It was working for some time very good. I don't know after which commit its broke.

Anyone have problems with it?

 cdc_ether 1-1.4:1.0 eth1: register 'cdc_ether' at usb-1e1c0000.xhci-1.4, CDC Ethernet Device, 58:2c:80:13:92:63
[63148.217235] cdc_ether 1-1.4:1.0 eth1: kevent 12 may have been dropped
[63148.311900] usb 1-1.5: new high-speed USB device number 46 using xhci-mtk
[63153.481872] usb 1-1.5: device descriptor read/64, error -145
[63165.801809] usb 1-1.5: device descriptor read/64, error -145
[63166.021867] usb 1-1.5: new high-speed USB device number 47 using xhci-mtk
[63171.161865] usb 1-1.5: device descriptor read/64, error -145
[63186.521781] usb 1-1.5: device descriptor read/64, error -145
[63186.641849] usb 1-1-port5: attempt power cycle
[63187.301840] usb 1-1.5: new high-speed USB device number 48 using xhci-mtk
[63189.332315] usb 1-1: USB disconnect, device number 44
[63192.341905] xhci-mtk 1e1c0000.xhci: Timeout while waiting for setup device command
[63192.561824] xhci-mtk 1e1c0000.xhci: ERROR: unexpected setup address command completion code 0x11.
[63192.781779] usb 1-1.5: device not accepting address 48, error -22
[63192.788121] usb 1-1.4: USB disconnect, device number 45
[63192.793724] cdc_ether 1-1.4:1.0 eth1: unregister 'cdc_ether' usb-1e1c0000.xhci-1.4, CDC Ethernet Device
[63193.251834] usb 1-1: new high-speed USB device number 50 using xhci-mtk
[63193.453842] hub 1-1:1.0: USB hub found
[63193.457837] hub 1-1:1.0: 7 ports detected
[63193.781825] usb 1-1.4: new high-speed USB device number 51 using xhci-mtk
[63193.919429] cdc_ether 1-1.4:1.0 eth1: register 'cdc_ether' at usb-1e1c0000.xhci-1.4, CDC Ethernet Device, 58:2c:80:13:92:63
[63193.921058] cdc_ether 1-1.4:1.0 eth1: kevent 12 may have been dropped
[63194.061861] usb 1-1.5: new high-speed USB device number 52 using xhci-mtk
[63199.241917] usb 1-1.5: device descriptor read/64, error -145

I can not find the path, and the dropbear configuration does not appear anywhere, my firmware is not installed correctly?
any ideas?

I can not find the path, and the dropbear configuration does not appear anywhere, my firmware is not installed correctly?