hello, can anyone give me an idea on how to enable/add MediaTek MT7915E 802.11ac/ax/n 5G wireless on official 24.10.5 firmware?
after flash, only 2.4G (radio0) is available.
dmesh -
root@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.119 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r29087-d9c5716d1d) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Wed Dec 17 21:08:22 2025
[ 0.000000] Machine model: Xiaomi Redmi Router AX6S
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] percpu: Embedded 18 pages/cpu s35112 r8192 d30424 u73728
[ 0.000000] pcpu-alloc: s35112 r8192 d30424 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 swiotlb=512 ubi.block=0,fit root=/dev/fit0
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 2.
[ 0.000000] software IO TLB: mapped [mem 0x000000004f900000-0x000000004fa00000] (1MB)
[ 0.000000] Memory: 242900K/262144K available (9152K kernel code, 952K rwdata, 1624K rodata, 448K init, 312K bss, 19244K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc080010000
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.008265] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[ 0.018663] pid_max: default: 32768 minimum: 301
[ 0.026060] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.033318] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.043649] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[ 0.053037] rcu: Hierarchical SRCU implementation.
[ 0.057847] rcu: Max phase no-delay instances is 1000.
[ 0.063486] smp: Bringing up secondary CPUs ...
[ 0.068437] Detected VIPT I-cache on CPU1
[ 0.068511] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.068575] smp: Brought up 1 node, 2 CPUs
[ 0.083258] SMP: Total of 2 processors activated.
[ 0.087974] CPU features: detected: 32-bit EL0 Support
[ 0.093130] CPU features: detected: CRC32 instructions
[ 0.098310] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.106696] CPU: All CPU(s) started at EL2
[ 0.110800] alternatives: applying system-wide alternatives
[ 0.120750] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.130640] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.138700] pinctrl core: initialized pinctrl subsystem
[ 0.145192] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.151422] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.158529] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.166317] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.174669] thermal_sys: Registered thermal governor 'fair_share'
[ 0.174673] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.180785] thermal_sys: Registered thermal governor 'step_wise'
[ 0.186815] thermal_sys: Registered thermal governor 'user_space'
[ 0.192895] ASID allocator initialised with 65536 entries
[ 0.205081] pstore: Using crash dump compression: deflate
[ 0.210503] pstore: Registered ramoops as persistent store backend
[ 0.216702] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.230110] Modules: 29616 pages in range for non-PLT usage
[ 0.230122] Modules: 521136 pages in range for PLT usage
[ 0.236782] cryptd: max_cpu_qlen set to 1000
[ 0.247412] SCSI subsystem initialized
[ 0.251258] libata version 3.00 loaded.
[ 0.256443] clocksource: Switched to clocksource arch_sys_counter
[ 0.264686] NET: Registered PF_INET protocol family
[ 0.269761] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.278224] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.286620] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.294397] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.302186] TCP bind hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.309406] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.316080] MPTCP token hash table entries: 256 (order: 1, 6144 bytes, linear)
[ 0.323423] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.329988] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.337165] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.342879] PCI: CLS 0 bytes, default 64
[ 0.347923] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.359001] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.364857] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.428819] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.436992] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"
[ 0.455217] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.468426] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.478135] printk: console [ttyS0] disabled
[ 0.502881] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 118, base_baud = 1562500) is a ST16650V2
[ 0.512212] printk: console [ttyS0] enabled
[ 0.520592] printk: bootconsole [uart8250] disabled
[ 0.531518] mtk_rng 1020f000.rng: registered RNG driver
[ 0.531664] random: crng init done
[ 0.543101] loop: module loaded
[ 0.546882] mtk-ecc 1100e000.ecc: probed
[ 0.552112] spi-nand spi0.0: ESMT SPI NAND was found.
[ 0.557199] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.565312] mtk-snand 1100d000.spi: ECC strength: 4 bits per 512 bytes
[ 0.573133] [BBT] BMT.v2 is found at 0x3ff
[ 0.577816] 10 fixed-partitions partitions found on MTD device spi0.0
[ 0.584275] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.590560] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.597040] Creating 10 MTD partitions on "spi0.0":
[ 0.601912] 0x000000000000-0x000000080000 : "Preloader"
[ 0.608020] 0x000000080000-0x0000000c0000 : "ATF"
[ 0.613264] 0x0000000c0000-0x000000140000 : "u-boot"
[ 0.619025] 0x000000140000-0x000000180000 : "u-boot-env"
[ 0.624845] 0x000000180000-0x0000001c0000 : "bdata"
[ 0.630269] 0x0000001c0000-0x000000240000 : "factory"
[ 0.636142] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.642606] 0x000000240000-0x000000280000 : "crash"
[ 0.648111] 0x000000280000-0x0000002c0000 : "crash_log"
[ 0.653869] 0x0000002c0000-0x000000340000 : "ubi-loader"
[ 0.660001] 0x000000340000-0x0000075c0000 : "ubi"
[ 0.784949] ubi0: default fastmap pool size: 45
[ 0.789488] ubi0: default fastmap WL pool size: 22
[ 0.794270] ubi0: attaching mtd9
[ 1.047522] ubi0: scanning is finished
[ 1.055294] ubi0: attached mtd9 (name "ubi", size 114 MiB)
[ 1.060792] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.067663] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.074443] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.081402] ubi0: good PEBs: 916, bad PEBs: 0, corrupted PEBs: 0
[ 1.087404] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.094617] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1766005702
[ 1.103744] ubi0: available PEBs: 1, total reserved PEBs: 915, PEBs reserved for bad PEB handling: 19
[ 1.112965] ubi0: background thread "ubi_bgt0d" started, PID 285
[ 1.113436] block ubiblock0_0: created from ubi0:0(fit)
[ 1.260709] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc0814e0000, irq 123
[ 1.270493] i2c_dev: i2c /dev entries driver
[ 1.276104] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.285794] NET: Registered PF_INET6 protocol family
[ 1.291672] Segment Routing with IPv6
[ 1.295353] In-situ OAM (IOAM) with IPv6
[ 1.299379] NET: Registered PF_PACKET protocol family
[ 1.304457] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.317708] 8021q: 802.1Q VLAN Support v1.8
[ 1.343152] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 1.349775] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 1.355605] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.622998] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 1.629216] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.634699] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 1.641583] pci_bus 0000:00: scanning bus
[ 1.645772] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
[ 1.651959] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
[ 1.662076] pci_bus 0000:00: fixups for bus
[ 1.666269] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.672973] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.681048] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.688142] pci_bus 0000:01: scanning bus
[ 1.692299] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
[ 1.698486] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.705812] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.713140] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.721113] pci 0000:01:00.0: supports D1 D2
[ 1.725378] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.732017] pci 0000:01:00.0: PME# disabled
[ 1.736549] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.776677] pci_bus 0000:01: fixups for bus
[ 1.780868] pci_bus 0000:01: bus scan returning with max=01
[ 1.786473] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.793107] pci_bus 0000:00: bus scan returning with max=01
[ 1.798722] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
[ 1.806387] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
[ 1.814390] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
[ 1.821183] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
[ 1.829007] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
[ 1.836833] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
[ 1.844652] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.849620] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
[ 1.856542] pcieport 0000:00:00.0: assign IRQ: got 127
[ 1.861682] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 1.867791] pcieport 0000:00:00.0: enabling bus mastering
[ 1.873239] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44ecd0c0
[ 1.880620] pcieport 0000:00:00.0: PME: Signaling with IRQ 127
[ 1.886527] pcieport 0000:00:00.0: save config 0x00: 0x325814c3
[ 1.892441] pcieport 0000:00:00.0: save config 0x04: 0x00100006
[ 1.898363] pcieport 0000:00:00.0: save config 0x08: 0x06040000
[ 1.904276] pcieport 0000:00:00.0: save config 0x0c: 0x00010000
[ 1.910194] pcieport 0000:00:00.0: save config 0x10: 0x0000000c
[ 1.916106] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[ 1.922024] pcieport 0000:00:00.0: save config 0x18: 0x40010100
[ 1.927941] pcieport 0000:00:00.0: save config 0x1c: 0x04200000
[ 1.933854] pcieport 0000:00:00.0: save config 0x20: 0x20102000
[ 1.939770] pcieport 0000:00:00.0: save config 0x24: 0x00000000
[ 1.945684] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[ 1.951600] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[ 1.957521] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[ 1.963435] pcieport 0000:00:00.0: save config 0x34: 0x00000050
[ 1.969352] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[ 1.975265] pcieport 0000:00:00.0: save config 0x3c: 0x0002017f
[ 1.981857] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 1.989894] FIT: Detected U-Boot 2024.10-OpenWrt-r29087-d9c5716d1d
[ 1.996078] FIT: Selected configuration: "config-1" (OpenWrt xiaomi_redmi-router-ax6s)
[ 2.004014] FIT: kernel sub-image 0x00001000..0x00569612 "kernel-1" (ARM64 OpenWrt Linux-6.6.119)
[ 2.013856] FIT: flat_dt sub-image 0x0056a000..0x00571314 "fdt-1" (ARM64 OpenWrt xiaomi_redmi-router-ax6s device tree blob)
[ 2.025865] FIT: filesystem sub-image 0x00572000..0x00a13fff "rootfs-1" (ARM64 OpenWrt xiaomi_redmi-router-ax6s rootfs)
[ 2.037655] block ubiblock0_0: mapped 1 uImage.FIT filesystem sub-image as /dev/fit0
[ 2.117459] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 2.126572] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 2.137865] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=129)
[ 2.160068] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=130)
[ 2.182057] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=131)
[ 2.204039] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=132)
[ 2.215266] mtk_soc_eth 1b100000.ethernet eth0: entered promiscuous mode
[ 2.222014] DSA: tree 0 setup
[ 2.225353] clk: Disabling unused clocks
[ 2.232504] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 2.239843] Freeing unused kernel memory: 448K
[ 2.244330] Run /sbin/init as init process
[ 2.248424] with arguments:
[ 2.251382] /sbin/init
[ 2.254080] with environment:
[ 2.257221] HOME=/
[ 2.259571] TERM=linux
[ 2.434824] init: Console is alive
[ 2.438440] init: - watchdog -
[ 2.775751] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.799878] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.809704] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.825001] init: - preinit -
[ 3.182038] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 3.190899] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 3.206350] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 5.222410] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 7.449902] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 7.455646] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 769
[ 7.473336] UBIFS (ubi0:1): recovery needed
[ 7.557590] UBIFS (ubi0:1): recovery completed
[ 7.562129] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 7.569980] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.579901] UBIFS (ubi0:1): FS size: 100945920 bytes (96 MiB, 795 LEBs), max 806 LEBs, journal size 5079040 bytes (4 MiB, 40 LEBs)
[ 7.591648] UBIFS (ubi0:1): reserved for root: 4767925 bytes (4656 KiB)
[ 7.598266] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID A41B1588-D8EA-4A26-A36B-4D9A7DC58279, small LPT model
[ 7.614254] mount_root: switching to ubifs overlay
[ 7.624423] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 7.637937] urandom-seed: Seeding with /etc/urandom.seed
[ 7.745267] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 7.755446] procd: - early -
[ 7.758439] procd: - watchdog -
[ 8.327250] procd: - watchdog -
[ 8.331944] procd: - ubus -
[ 8.489025] procd: - init -
[ 8.836772] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.872643] Loading modules backported from Linux version v6.12.61-0-gdcbeffaf66d0
[ 8.880258] Backport generated by backports.git v6.1.110-1-35-g410656ef
[ 8.953169] mt7622-wmac 18000000.wmac: registering led 'mt76-phy0'
[ 8.988057] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.040077] urngd: v1.0.2 started.
[ 9.055406] mt7915e 0000:01:00.0: assign IRQ: got 127
[ 9.060545] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
[ 9.066638] mt7915e 0000:01:00.0: enabling bus mastering
[ 9.098662] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[ 9.098662]
[ 9.202650] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44ecd0c0
[ 9.234141] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834
[ 9.299054] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20240429200716a
[ 9.299054]
[ 9.434562] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20240429200752
[ 9.495388] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20240429200812
[ 9.610985] mt7915e 0000:01:00.0: registering led 'mt76-phy1'
[ 9.691963] PPP generic driver version 2.4.2
[ 9.698105] NET: Registered PF_PPPOX protocol family
[ 9.711835] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 9.719788] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 9.732997] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.038812] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 13.054778] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 13.063568] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 13.079909] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 13.087999] br-lan: port 1(lan1) entered blocking state
[ 13.093239] br-lan: port 1(lan1) entered disabled state
[ 13.098557] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 13.104836] mtk_soc_eth 1b100000.ethernet eth0: entered allmulticast mode
[ 13.115295] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 13.144300] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 13.163150] br-lan: port 2(lan2) entered blocking state
[ 13.168531] br-lan: port 2(lan2) entered disabled state
[ 13.173849] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 13.191237] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 13.211691] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 13.220229] br-lan: port 3(lan3) entered blocking state
[ 13.225473] br-lan: port 3(lan3) entered disabled state
[ 13.230809] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
[ 13.239122] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
[ 13.258747] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 14.889062] mt7530-mdio mdio-bus:1f lan2: Link is Up - 10Mbps/Full - flow control off
[ 14.957294] br-lan: port 2(lan2) entered blocking state
[ 14.962545] br-lan: port 2(lan2) entered forwarding state
[ 14.970658] br-lan: port 4(wl1-ap0) entered blocking state
[ 14.976183] br-lan: port 4(wl1-ap0) entered disabled state
[ 14.981732] mt7915e 0000:01:00.0 wl1-ap0: entered allmulticast mode
[ 14.988228] mt7915e 0000:01:00.0 wl1-ap0: entered promiscuous mode
[ 14.998438] mt7915e 0000:01:00.0 wl1-ap0: left allmulticast mode
[ 15.004480] mt7915e 0000:01:00.0 wl1-ap0: left promiscuous mode
[ 15.010547] br-lan: port 4(wl1-ap0) entered disabled state
[ 15.238896] br-lan: port 4(wl0-ap0) entered blocking state
[ 15.244422] br-lan: port 4(wl0-ap0) entered disabled state
[ 15.250006] mt7622-wmac 18000000.wmac wl0-ap0: entered allmulticast mode
[ 15.256941] mt7622-wmac 18000000.wmac wl0-ap0: entered promiscuous mode
[ 15.263695] br-lan: port 4(wl0-ap0) entered blocking state
[ 15.269191] br-lan: port 4(wl0-ap0) entered forwarding state
[ 16.026600] br-lan: port 4(wl0-ap0) entered disabled state
[ 16.741297] mt7530-mdio mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control off
[ 19.343618] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 19.343668] br-lan: port 1(lan1) entered blocking state
[ 19.356827] br-lan: port 1(lan1) entered forwarding state
[ 22.229783] br-lan: port 4(wl0-ap0) entered blocking state
[ 22.235284] br-lan: port 4(wl0-ap0) entered forwarding state
