I have a wrt3200acm with OpenWrt on both partitions.
I would like OEM f/w on one partition.
I tried 3 flash methods :
- Flash from GUI,
- Transfer to tmp and sysupgrade.
- Tftp flash with serial output.
I tried 3 different OEM f/w builds.
OEM f/w write is ok but boot sequence hangs at "Starting smbd ..."
Flashing OpenWrt works with all 3 methods, from either partition.
Here's the full boot sequence.....
BootROM - 1.73
Booting from NAND flash
General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0
Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 6 | SATA0 |
| 1 | 5 | PCIe0 |
| 2 | 6 | SATA1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe1 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01 (Apr 08 2016 - 15:47:50) Marvell version: 2015_T1.QA.0p16
Boot version : v0.0.4
Board: RD-NAS-88F6820-DDR3
SoC: MV88F6820 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1866 [MHz]
L2 @ 933 [MHz]
TClock @ 200 [MHz]
DDR3 @ 933 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 512 MiB
NAND: 256 MiB
MMC: mv_sdh: 0
DEVINFO offset == 0x7e0000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
S-ENV offset == 0x220000
#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3
S-ENV offset == 0x220000
[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:0, next_record:55
[boot_count_write] erase:0, auto_recovery->block_offset:0x220000 offset=0x23B800
Updating boot_count ...
[boot_count_write] offset:0x23B800 , length:2048
done
PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode
Map: Code: 0x1feab000:0x1ff75a20
BSS: 0x1ffef164
Stack: 0x1f9aaf20
Heap: 0x1f9ab000:0x1feab000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
U-Boot Environment: 0x00200000:0x00220000 (NAND)
Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x01 |
| egiga1 | SGMII | 0x00 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linksys WRT3200 Router
Created: 2016-09-26 0:58:08 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4640547 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.70 (root@build-vm) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Sun Sep 25 17:57:52 PDT 2016
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Development Board
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c1151000 s7488 r8192 d12992 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
allocated 1048576 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 512MB = 512MB total
Memory: 508768k/508768k available, 15520k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc08417c0 (8422 kB)
.init : 0xc0842000 - 0xc0883d40 ( 264 kB)
.data : 0xc0884000 - 0xc08d81e0 ( 337 kB)
.bss : 0xc08d81e0 - 0xc099f04c ( 796 kB)
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
NR_IRQS:16 nr_irqs:16 16
LSP version: linux-3.10.70-2015_T1.1p7
sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
Console: colour dummy device 80x30
Calibrating delay loop... 3726.54 BogoMIPS (lpj=18632704)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys memory
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Calibrating local timer... 933.29MHz.
Setting up static identity map for 0xc0642fd8 - 0xc0643030
mvebu-pmsu: Initializing Power Management Service Unit
Initializing CPU Reset module
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (7453.08 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
xor: measuring software checksum speed
arm4regs : 3309.200 MB/sec
8regs : 2234.400 MB/sec
32regs : 1905.600 MB/sec
xor: using function: arm4regs (3309.200 MB/sec)
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated
bio: create slab <bio-0> at 0
raid6: int32x1 232 MB/s
raid6: int32x2 344 MB/s
raid6: int32x4 437 MB/s
raid6: int32x8 444 MB/s
raid6: using algorithm int32x8 (444 MB/s)
raid6: using intx1 recovery algorithm
mvebu-pcie pcie-controller.6: PCIe0.0: link up
mvebu-pcie pcie-controller.6: PCIe1.0: link up
mvebu-pcie pcie-controller.6: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers disabled
PCI: bus2: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe02fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
pci 0000:00:02.0: PCI bridge to [bus 02]
pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe06fffff]
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
PCI: enabling device 0000:00:02.0 (0140 -> 0143)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource armada_370_xp_clocksource
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 993
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060800.xor: freeing 1 in use descriptors!
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060900.xor: freeing 1 in use descriptors!
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi0 : ahci_mv_platform
scsi1 : ahci_mv_platform
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
11 cmdlinepart partitions found on MTD device armada-nand
Creating 11 MTD partitions on "armada-nand":
0x000000000000-0x000000200000 : "uboot"
0x000000200000-0x000000220000 : "u_env"
0x000000220000-0x000000260000 : "s_env"
0x0000007e0000-0x000000820000 : "devinfo"
0x000000820000-0x000000a00000 : "sysdiag"
0x000000a00000-0x000005a00000 : "kernel"
0x000001000000-0x000005a00000 : "rootfs"
0x000005a00000-0x00000aa00000 : "alt_kernel"
0x000006000000-0x00000aa00000 : "alt_rootfs"
0x000000a00000-0x00000aa00000 : "ubifs"
0x00000aa00000-0x000010000000 : "syscfg"
bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
SoC: model = 0x6820, revision = 0x4
mvPncVirtBase = 0xe0c00000, pncTcamSize = 1024
o 3 Giga ports supported
o SKB recycle supported for SWF (Disabled)
o NETA acceleration mode 4
o BM supported for CPU: 4 BM pools
o PnC supported (Enabled)
o RX Queue support: 8 Queues * 256 Descriptors
o TX Queue support: 8 Queues * 532 Descriptors
o GSO supported
o GRO supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Driver DEBUG statistics enabled
port #0: is_sgmii=0, is_rgmii=1, phy_addr=0
o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800
o Port 0 is connected to Linux netdevice
o eth0, ifindex = 3, GbE port = 0
giga p=0: mtu=1500, mac=60:38:e0:bd:5a:68 (hw config)
port #2: is_sgmii=1, is_rgmii=0, phy_addr=1
o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048
o Port 2 is connected to Linux netdevice
o eth1, ifindex = 4, GbE port = 2
giga p=2: mtu=1500, mac=3e:30:2b:d8:83:c4 (random)
(error) mv_switch_probe(5780) (rc=-22): read switch fdt file failed
mv_soho_switch: probe of switch.3 failed with error 1
o Loading Switch QuarterDeck driver
o Device ID : 0x352
o No. of Ports : 7
o CPU Port : 5
o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC
o Setting Switch Port #6 connected to GMAC port for 1000 Full with FC
Switch driver init:
o preset mode = Transparent
o tag mode = No Tag
port #0 establish switch connection
libphy: orion_mdio_bus: probed
mdio_bus f1072004.mdio-mi: cannot get PHY at address 0
mdio_bus f1072004.mdio-mi: cannot get PHY at address 1
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
PPP generic driver version 2.4.2
PPP BSD Compression module registered
ata1: SATA link down (SStatus 0 SControl 300)
PPP Deflate Compression module registered
ata2: SATA link down (SStatus 0 SControl 300)
NET: Registered protocol family 24
PPTP driver version 0.8.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
i2c /dev entries driver
armada_thermal f10e4078.thermal: Overheat threshold between 92..107
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
usbcore: registered new interface driver bcm203x
usbcore: registered new interface driver bpa10x
usbcore: registered new interface driver bfusb
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: new high speed SDIO card at address 0001
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1)
armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xfffff
mvCesaInit: channels=2, session=640, queue=256
armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
cesadev_init(c085f288)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Loading Marvell spi device
NET: Registered protocol family 26
u32 classifier
Netfilter messages via NETLINK v0.30.
Port 3: Link-up, Full-duplex, Speed-1000Mbps.
nfnl_acct: registering with nfnetlink.
nf_conntrack version 0.5.0 (7949 buckets, 31796 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.7 loading
ipip: IPv4 over IPv4 tunneling driver
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
nf_nat_rtsp v0.7 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
regulator-dummy: disabling
input: gpio_keys.4 as /devices/soc.0/internal-regs.1/gpio_keys.4/input/input0
mvebu-rtc f10a3800.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)
Waiting 1sec before mounting root device...
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140000: 0x4c2e instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140004: 0x534b instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140008: 0x302e instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0214000c: 0x3030 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140010: 0x5742 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140014: 0x3233 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140018: 0x4341 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0214001c: 0x2020 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140020: 0x4535 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02140024: 0x4430 instead
jffs2: Further such events for this erase block will not be printed
VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
devtmpfs: mounted
Freeing unused kernel memory: 260K (c0842000 - c0883000)
*********************************************************************************
_ _ __ _ __ _____ __ __ _____
| | | || \ | | / // ____]\ \ / // ____]TM
| | | || \ | | / /| (___ \ V /| (____
| | | || |\ \| |\ \ \____ \ \ / \____ \
| |_____ | || | \ | \ \ ____) | | | ____) |
|_______||_||_| \__| \_\[____ / |_| [_____/
(c) 2014 Belkin International, Inc. and/or its affiliates. All rights reserved.
Booting rango (firmware version 1.0.5.175944)
*********************************************************************************
[utopia][init] System Initialization
[utopia][init] Creating /proc
[utopia][init] Creating /sys
[utopia][init] Creating /dev
[utopia][init] Creating /tmp
[utopia][init] Allocating 100M for /tmp
[utopia][init] Prepairing /dev/pts
[utopia][init] Setting /tmp and /var permissions
[utopia][init] Starting udev..
orion_wdt: Initial timeout 171 sec
Attempting mount of ubifs syscfg partition
UBI device number 0, total 680 LEBs (86343680 bytes, 82.3 MiB), available 8 LEBs (1015808 bytes, 992.0 KiB), LEB size 126976 bytes (124.0 KiB)
[utopia][init] Using persistent syscfg data from /var/config/syscfg
[utopia][init] Starting system logging
[utopia][init] Starting sysevent subsystem
net.netfilter.nf_conntrack_acct = 1
watchdog running
[utopia][init] Setting any unset system values to default
[utopia][init] no persistence config file (/var/config/pstcfg) found
mac_setup.sh, setting up MAC addresses for all interfaces based on 60:38:E0:BD:5A:68
NTP Servers do not need to be updated
configuring switch port to router mode
checking for interactive script start up...
Updating BootCount Page[56]:1C000 ... Done
attempting to sync sysinfo.cgi auth credentials
cpu temp monitor created
Tue Nov 14 15:34:00 UTC 2023
wan, sysevent received: wan-start
wdev0 no private ioctls.
wdev1 no private ioctls.
Bad argument `br0'
Error occurred at line: 15
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
â–’,â–’â–’Bad argument `br0'
Error occurred at line: 15
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
â–’,â–’â–’Lighttpd Model Base: WRT3200ACM
Generating Rainier lighttpd config
wdev0ap0 no private ioctls.
wdev0ap1 no private ioctls.
wdev0ap2 no private ioctls.
wdev0ap3 no private ioctls.
wdev1ap0 no private ioctls.
wdev1ap1 no private ioctls.
wdev1ap2 no private ioctls.
Build temporary www configuration directory:
$1$NPzFsEQj$yQdK.cYHa.gHE7zI49sYs/
wifi, sysevent received: lan-started (Tue Nov 14 16:34:05 CET 2023)
wifi, service_start()
Registering Service myrouter._http._tcp.local port 80
Got a reply for myrouter._http._tcp.local.: Name now registered and active
Bad argument `br0'
Error occurred at line: 15
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
[utopia] Not setting ppp_clamp_mtu
Not ready for JNAP. Sleeping for 15 seconds...
â–’,â–’â–’wifi, EEPROM powertables support
wifi, wdev0 regioncode: wdev0 getregioncode:16
wifi, wdev0 powertable: wdev0 gettxpower:0x00
wifi, wdev1 regioncode: wdev1 getregioncode:16
wifi, wdev1 powertable: wdev1 gettxpower:0x00
wifi, wifi_physical_start(wdev0)
wifi, wl1_state=down, do not start physical wdev0
wifi, wifi_virtual_start(wdev0)
wifi, wl1_state=down, do not start virtual wdev0ap0
wifi, wifi_physical_start(wdev1)
wifi, wl0_state=down, do not start physical wdev1
wifi, wifi_virtual_start(wdev1)
wifi, wl0_state=down, do not start virtual wdev1ap0
wifi, start_hostapd()
Bad argument `br0'
Error occurred at line: 15
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
â–’,â–’â–’[utopia] Not setting ppp_clamp_mtu on dslite protocol
wan, sysevent received: phylink_wan_state
Bad argument `br0'
Error occurred at line: 15
Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information.
â–’,â–’â–’Restarting nfqrecv service...
Starting smbd ...
