Upgraded cleanly from OpenWRT.
My 5ghz is working just fine.
When i had OpenWRT my laptop and LEDwifi could not connect to my ssid wich had the same name, upgraded to LEDE and the problem still existed.
So basic troubleshooting, named the ssid different and now i can see my 5ghz but my 2.4 wont show.
Aslo in the config page:
Signal 0dBm and Bitrate 0.0
Tried various settings "Legacy/N" Different channels and ecryptions. Same result always.
Systemlog
Sun Apr 9 15:49:54 2017 kern.info kernel: [12474.691511] device wlan1 left promiscuous mode
Sun Apr 9 15:49:54 2017 kern.info kernel: [12474.696029] br-lan: port 2(wlan1) entered disabled state
Sun Apr 9 15:49:54 2017 daemon.notice hostapd: wlan1: interface state ENABLED->DISABLED
Sun Apr 9 15:49:54 2017 daemon.notice hostapd: wlan1: AP-DISABLED
Sun Apr 9 15:49:54 2017 daemon.notice hostapd: wlan1: CTRL-EVENT-TERMINATING
Sun Apr 9 15:49:54 2017 daemon.notice hostapd: nl80211: deinit ifname=wlan1 disabled_11b_rates=0
Sun Apr 9 15:49:54 2017 daemon.notice hostapd: nl80211: Failed to remove interface wlan1 from bridge br-lan: Invalid argument
Sun Apr 9 15:49:54 2017 kern.debug kernel: [12474.777610] ieee80211 phy1: change: 0x40
Sun Apr 9 15:49:54 2017 kern.debug kernel: [12474.828466] ieee80211 phy1: change: 0x100
Sun Apr 9 15:49:55 2017 daemon.info odhcpd[1203]: Initial RA router lifetime 0, 1 address(es) available on br-lan
Sun Apr 9 15:49:55 2017 daemon.notice netifd: radio1 (24829): command failed: Not supported (-95)
Sun Apr 9 15:49:55 2017 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Sun Apr 9 15:49:55 2017 kern.debug kernel: [12476.215386] ieee80211 phy1: change: 0xffffffff
Sun Apr 9 15:49:55 2017 kern.info kernel: [12476.278595] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Apr 9 15:49:55 2017 kern.info kernel: [12476.285499] device wlan1 entered promiscuous mode
Sun Apr 9 15:49:55 2017 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Apr 9 15:50:00 2017 daemon.err hostapd: Using interface wlan1 with hwaddr 62:38:e0:0c:37:c8 and ssid "nerdinternatet1"
Sun Apr 9 15:50:00 2017 kern.debug kernel: [12481.351138] ieee80211 phy1: change: 0x100
Sun Apr 9 15:50:00 2017 kern.debug kernel: [12481.363316] ieee80211 phy1: change: 0x40
Sun Apr 9 15:50:01 2017 kern.info kernel: [12481.484342] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Sun Apr 9 15:50:01 2017 kern.info kernel: [12481.490796] br-lan: port 2(wlan1) entered forwarding state
Sun Apr 9 15:50:01 2017 kern.info kernel: [12481.496327] br-lan: port 2(wlan1) entered forwarding state
Sun Apr 9 15:50:01 2017 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Sun Apr 9 15:50:01 2017 daemon.notice hostapd: wlan1: AP-ENABLED
Sun Apr 9 15:50:01 2017 daemon.notice netifd: Network device 'wlan1' link is up
Sun Apr 9 15:50:03 2017 kern.info kernel: [12483.488279] br-lan: port 2(wlan1) entered forwarding state
Sun Apr 9 15:50:15 2017 daemon.notice odhcpd[1203]: Got DHCPv6 request
Kernellog (lower part)
[ 15.581333] urandom-seed: Seeding with /etc/urandom.seed
[ 15.627079] procd: - early -
[ 15.629994] procd: - watchdog -
[ 16.257526] procd: - ubus -
[ 16.312437] procd: - init -
[ 16.597815] tun: Universal TUN/TAP device driver, 1.6
[ 16.602909] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.609928] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.616750] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 16.624366] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 16.638184] <<Marvell 802.11ac Wireless Network Driver version 10.3.2.0-20170110>>
[ 16.645816] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 16.651564] ieee80211 phy0: priv->iobase0 = e0e80000
[ 16.651577] ieee80211 phy0: priv->iobase1 = e1000000
[ 16.651612] ieee80211 phy0: priv->pcmd_buf = dd87c000 priv->pphys_cmd_buf = 1d87c000
[ 16.679241] ieee80211 phy0: fw download start
[ 16.796114] ieee80211 phy0: FwSize = 118776 downloaded Size = 118776 curr_iteration 65496
[ 17.767201] ieee80211 phy0: fw download complete
[ 17.768208] ieee80211 phy0: pcmd = dd87c000
[ 17.786204] ieee80211 phy0: firmware version: 0x702091a
[ 18.138300] ieee80211 phy0: firmware region code: 30
[ 18.166873] ieee80211 phy0: 2G disabled, 5G enabled
[ 18.171791] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 18.177179] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 18.182920] ieee80211 phy1: priv->iobase0 = e1180000
[ 18.182932] ieee80211 phy1: priv->iobase1 = e1300000
[ 18.182966] ieee80211 phy1: priv->pcmd_buf = dd544000 priv->pphys_cmd_buf = 1d544000
[ 18.199881] ieee80211 phy1: fw download start
[ 18.283439] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 18.320128] ieee80211 phy1: FwSize = 118776 downloaded Size = 118776 curr_iteration 65511
[ 19.067244] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
[ 19.277199] ieee80211 phy1: fw download complete
[ 19.278192] ieee80211 phy1: pcmd = dd544000
[ 19.296197] ieee80211 phy1: firmware version: 0x702091a
[ 19.648203] ieee80211 phy1: firmware region code: 30
[ 19.674878] ieee80211 phy1: 2G enabled, 5G disabled
[ 19.679779] ieee80211 phy1: 4 TX antennas, 4 RX antennas
[ 19.702949] Bridge firewalling registered
[ 19.707483] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.714202] nf_conntrack version 0.5.0 (8025 buckets, 32100 max)
[ 19.815119] xt_time: kernel timezone is -0000
[ 19.821408] PPP generic driver version 2.4.2
[ 19.825995] NET: Registered protocol family 24
[ 20.900158] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[ 20.907135] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 20.915374] device eth0 entered promiscuous mode
[ 20.920904] br-lan: port 1(eth0) entered forwarding state
[ 20.926344] br-lan: port 1(eth0) entered forwarding state
[ 20.939113] mvneta f1070000.ethernet eth1: configuring for fixed link mode
[ 20.946441] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 20.952408] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 20.962162] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.921210] br-lan: port 1(eth0) entered forwarding state
[ 23.285290] ieee80211 phy1: change: 0xffffffff
[ 23.349571] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 23.479334] ieee80211 phy0: change: 0xffffffff
[ 23.557526] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.563997] device wlan1 entered promiscuous mode
[ 23.571514] device wlan0 entered promiscuous mode
[ 28.569445] ieee80211 phy1: change: 0x100
[ 28.581226] ieee80211 phy1: change: 0x40
[ 28.585438] ieee80211 phy0: change: 0x100
[ 28.598256] ieee80211 phy0: change: 0x60
[ 28.741197] ieee80211 phy1: change: 0x40
[ 28.771193] ieee80211 phy0: change: 0x40
[ 28.901191] ieee80211 phy1: change: 0x40
[ 28.941195] ieee80211 phy0: change: 0x60
[ 29.009224] ieee80211 phy0: change: 0x100
[ 29.021227] ieee80211 phy0: change: 0x100
[ 29.034268] ieee80211 phy0: change: 0x62
[ 29.061194] ieee80211 phy1: change: 0x40
[ 29.104236] ieee80211 phy0: change: 0x40
[ 29.221200] ieee80211 phy1: change: 0x40
[ 29.381196] ieee80211 phy1: change: 0x40
[ 29.541190] ieee80211 phy1: change: 0x40
[ 29.701193] ieee80211 phy1: change: 0x40
[ 29.861199] ieee80211 phy1: change: 0x40
[ 30.021194] ieee80211 phy1: change: 0x40
[ 30.181204] ieee80211 phy1: change: 0x40
[ 30.341206] ieee80211 phy1: change: 0x40
[ 30.501198] ieee80211 phy1: change: 0x40
[ 30.661198] ieee80211 phy1: change: 0x40
[ 30.720216] ieee80211 phy1: change: 0x100
[ 30.788853] ieee80211 phy1: change: 0x100
[ 30.801195] ieee80211 phy1: change: 0x42
[ 30.959767] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 30.966239] br-lan: port 2(wlan1) entered forwarding state
[ 30.971789] br-lan: port 2(wlan1) entered forwarding state
[ 32.971187] br-lan: port 2(wlan1) entered forwarding state
[ 89.281108] ieee80211 phy0: change: 0x40
[ 89.350121] ieee80211 phy0: change: 0x100
[ 89.435428] ieee80211 phy0: change: 0x100
[ 89.448122] ieee80211 phy0: change: 0x42
[ 89.517135] ieee80211 phy0: change: 0x40
[ 89.701212] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 89.707722] br-lan: port 3(wlan0) entered forwarding state
[ 89.713274] br-lan: port 3(wlan0) entered forwarding state
[ 91.711090] br-lan: port 3(wlan0) entered forwarding state
[ 265.625639] device wlan1 left promiscuous mode
[ 265.630179] br-lan: port 2(wlan1) entered disabled state
[ 265.729011] ieee80211 phy1: change: 0x40
[ 265.778807] ieee80211 phy1: change: 0x100
[ 267.278786] ieee80211 phy1: change: 0xffffffff
[ 267.343767] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 267.351165] device wlan1 entered promiscuous mode
[ 272.359966] ieee80211 phy1: change: 0x100
[ 272.373030] ieee80211 phy1: change: 0x40
[ 272.529687] ieee80211 phy1: change: 0x40
[ 272.689689] ieee80211 phy1: change: 0x40
[ 272.849693] ieee80211 phy1: change: 0x40
[ 273.009690] ieee80211 phy1: change: 0x40
[ 273.169715] ieee80211 phy1: change: 0x40
[ 273.329683] ieee80211 phy1: change: 0x40
[ 273.489682] ieee80211 phy1: change: 0x40
[ 273.649683] ieee80211 phy1: change: 0x40
[ 273.819684] ieee80211 phy1: change: 0x40
[ 273.979681] ieee80211 phy1: change: 0x40
[ 274.139680] ieee80211 phy1: change: 0x40
[ 274.299675] ieee80211 phy1: change: 0x40
[ 274.459696] ieee80211 phy1: change: 0x40
[ 274.514678] ieee80211 phy1: change: 0x100
[ 274.583116] ieee80211 phy1: change: 0x100
[ 274.596171] ieee80211 phy1: change: 0x42
[ 274.722136] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 274.728588] br-lan: port 2(wlan1) entered forwarding state
[ 274.734131] br-lan: port 2(wlan1) entered forwarding state
[ 276.729635] br-lan: port 2(wlan1) entered forwarding state
[ 343.694561] device wlan1 left promiscuous mode
[ 343.699091] br-lan: port 2(wlan1) entered disabled state
[ 343.788132] ieee80211 phy1: change: 0x40
[ 343.844000] ieee80211 phy1: change: 0x100
[ 347.930939] ieee80211 phy1: change: 0xffffffff
[ 347.995112] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 348.002266] device wlan1 entered promiscuous mode
[ 353.010908] ieee80211 phy1: change: 0x100
[ 353.023845] ieee80211 phy1: change: 0x40
[ 353.178827] ieee80211 phy1: change: 0x40
[ 353.338826] ieee80211 phy1: change: 0x40
[ 353.498838] ieee80211 phy1: change: 0x40
[ 353.658821] ieee80211 phy1: change: 0x40
[ 353.818816] ieee80211 phy1: change: 0x40
[ 353.978815] ieee80211 phy1: change: 0x40
[ 354.138818] ieee80211 phy1: change: 0x40
[ 354.298821] ieee80211 phy1: change: 0x40
[ 354.458818] ieee80211 phy1: change: 0x40
[ 354.618837] ieee80211 phy1: change: 0x40
[ 354.778814] ieee80211 phy1: change: 0x40
[ 354.938818] ieee80211 phy1: change: 0x40
[ 355.098854] ieee80211 phy1: change: 0x40
[ 355.152857] ieee80211 phy1: change: 0x100
[ 355.221632] ieee80211 phy1: change: 0x100
[ 355.233350] ieee80211 phy1: change: 0x42
[ 355.355840] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 355.362326] br-lan: port 2(wlan1) entered forwarding state
[ 355.367865] br-lan: port 2(wlan1) entered forwarding state
[ 357.358769] br-lan: port 2(wlan1) entered forwarding state
[ 7106.126395] conntrack: generic helper won't handle protocol 47. Please consider loading the specific helper module.
[10883.177658] device wlan1 left promiscuous mode
[10883.182221] br-lan: port 2(wlan1) entered disabled state
[10883.304864] ieee80211 phy1: change: 0x40
[10883.364732] ieee80211 phy1: change: 0x100
[10884.832666] ieee80211 phy1: change: 0xffffffff
[10884.895905] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[10884.902922] device wlan1 entered promiscuous mode
[10889.908280] ieee80211 phy1: change: 0x100
[10889.921026] ieee80211 phy1: change: 0x40
[10890.075630] ieee80211 phy1: change: 0x40
[10890.235591] ieee80211 phy1: change: 0x40
[10890.395591] ieee80211 phy1: change: 0x40
[10890.555618] ieee80211 phy1: change: 0x40
[10890.715584] ieee80211 phy1: change: 0x40
[10890.875587] ieee80211 phy1: change: 0x40
[10891.035578] ieee80211 phy1: change: 0x40
[10891.195580] ieee80211 phy1: change: 0x40
[10891.355586] ieee80211 phy1: change: 0x40
[10891.515576] ieee80211 phy1: change: 0x40
[10891.675569] ieee80211 phy1: change: 0x40
[10891.835573] ieee80211 phy1: change: 0x40
[10891.995573] ieee80211 phy1: change: 0x40
[10892.048607] ieee80211 phy1: change: 0x100
[10892.115260] ieee80211 phy1: change: 0x100
[10892.128325] ieee80211 phy1: change: 0x42
[10892.251605] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[10892.258055] br-lan: port 2(wlan1) entered forwarding state
[10892.263589] br-lan: port 2(wlan1) entered forwarding state
[10894.255599] br-lan: port 2(wlan1) entered forwarding state
[10962.328902] ieee80211 phy1: change: 0x40
[10962.380725] ieee80211 phy1: change: 0x100
[10962.411928] br-lan: port 2(wlan1) entered disabled state
[10980.560510] ieee80211 phy1: change: 0xffffffff
[10980.623556] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[10980.648047] ieee80211 phy1: change: 0x100
[10980.661100] ieee80211 phy1: change: 0x42
[10980.786556] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[10980.793004] br-lan: port 2(wlan1) entered forwarding state
[10980.798542] br-lan: port 2(wlan1) entered forwarding state
[10982.794456] br-lan: port 2(wlan1) entered forwarding state
[10993.412641] ieee80211 phy1: change: 0x40
[10993.464342] ieee80211 phy1: change: 0x100
[10993.498171] br-lan: port 2(wlan1) entered disabled state
[10999.158287] ieee80211 phy1: change: 0xffffffff
[10999.222354] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[10999.246824] ieee80211 phy1: change: 0x100
[10999.259291] ieee80211 phy1: change: 0x42
[10999.382309] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[10999.388774] br-lan: port 2(wlan1) entered forwarding state
[10999.394324] br-lan: port 2(wlan1) entered forwarding state
[11001.394236] br-lan: port 2(wlan1) entered forwarding state
[12268.530645] device wlan1 left promiscuous mode
[12268.535161] br-lan: port 2(wlan1) entered disabled state
[12268.549836] ieee80211 phy1: change: 0x40
[12268.600516] ieee80211 phy1: change: 0x100
[12270.003505] ieee80211 phy1: change: 0xffffffff
[12270.067694] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[12270.074598] device wlan1 entered promiscuous mode
[12275.136179] ieee80211 phy1: change: 0x100
[12275.149227] ieee80211 phy1: change: 0x40
[12275.270438] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[12275.276877] br-lan: port 2(wlan1) entered forwarding state
[12275.282413] br-lan: port 2(wlan1) entered forwarding state
[12277.280399] br-lan: port 2(wlan1) entered forwarding state
[12407.919346] device wlan1 left promiscuous mode
[12407.923860] br-lan: port 2(wlan1) entered disabled state
[12408.008319] ieee80211 phy1: change: 0x40
[12408.062597] ieee80211 phy1: change: 0x100
[12409.451507] ieee80211 phy1: change: 0xffffffff
[12409.515305] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[12409.522212] device wlan1 entered promiscuous mode
[12414.584793] ieee80211 phy1: change: 0x100
[12414.597858] ieee80211 phy1: change: 0x40
[12414.718042] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[12414.724488] br-lan: port 2(wlan1) entered forwarding state
[12414.730025] br-lan: port 2(wlan1) entered forwarding state
[12416.728985] br-lan: port 2(wlan1) entered forwarding state
[12430.632441] br-lan: port 2(wlan1) entered disabled state
[12430.637817] br-lan: port 3(wlan0) entered disabled state
[12430.643192] br-lan: port 1(eth0) entered disabled state
[12430.656929] device eth0 left promiscuous mode
[12430.661372] br-lan: port 1(eth0) entered disabled state
[12430.673817] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[12430.681216] device wlan0 left promiscuous mode
[12430.685729] br-lan: port 3(wlan0) entered disabled state
[12430.691757] device wlan1 left promiscuous mode
[12430.696259] br-lan: port 2(wlan1) entered disabled state
[12432.251978] ieee80211 phy0: change: 0x40
[12432.318831] ieee80211 phy0: change: 0x100
[12432.340911] ieee80211 phy1: change: 0x40
[12432.393835] ieee80211 phy1: change: 0x100
[12432.461419] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[12432.468393] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[12432.476918] device eth0 entered promiscuous mode
[12432.482783] br-lan: port 1(eth0) entered forwarding state
[12432.488223] br-lan: port 1(eth0) entered forwarding state
[12432.501687] mvneta f1070000.ethernet eth1: configuring for fixed link mode
[12432.508649] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[12432.514621] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[12432.522845] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[12434.151898] ieee80211 phy1: change: 0xffffffff
[12434.217452] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[12434.229557] device wlan1 entered promiscuous mode
[12434.372904] ieee80211 phy0: change: 0xffffffff
[12434.452223] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[12434.460288] device wlan0 entered promiscuous mode
[12434.465086] br-lan: port 3(wlan0) entered forwarding state
[12434.470644] br-lan: port 3(wlan0) entered forwarding state
[12434.478828] br-lan: port 1(eth0) entered forwarding state
[12435.218828] br-lan: port 3(wlan0) entered disabled state
[12439.481219] ieee80211 phy0: change: 0x100
[12439.493836] ieee80211 phy0: change: 0x40
[12439.518886] ieee80211 phy1: change: 0x100
[12439.531933] ieee80211 phy1: change: 0x40
[12439.654799] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[12439.661275] br-lan: port 2(wlan1) entered forwarding state
[12439.666808] br-lan: port 2(wlan1) entered forwarding state
[12439.668785] ieee80211 phy0: change: 0x40
[12439.838776] ieee80211 phy0: change: 0x100
[12439.906440] ieee80211 phy0: change: 0x100
[12439.918778] ieee80211 phy0: change: 0x42
[12439.988765] ieee80211 phy0: change: 0x40
[12440.132820] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[12440.139274] br-lan: port 3(wlan0) entered forwarding state
[12440.144803] br-lan: port 3(wlan0) entered forwarding state
[12441.658735] br-lan: port 2(wlan1) entered forwarding state
[12442.138733] br-lan: port 3(wlan0) entered forwarding state
[12474.691511] device wlan1 left promiscuous mode
[12474.696029] br-lan: port 2(wlan1) entered disabled state
[12474.777610] ieee80211 phy1: change: 0x40
[12474.828466] ieee80211 phy1: change: 0x100
[12476.215386] ieee80211 phy1: change: 0xffffffff
[12476.278595] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[12476.285499] device wlan1 entered promiscuous mode
[12481.351138] ieee80211 phy1: change: 0x100
[12481.363316] ieee80211 phy1: change: 0x40
[12481.484342] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[12481.490796] br-lan: port 2(wlan1) entered forwarding state
[12481.496327] br-lan: port 2(wlan1) entered forwarding state
[12483.488279] br-lan: port 2(wlan1) entered forwarding state
ifconfig
br-lan Link encap:Ethernet HWaddr 62:38:E0:0C:37:C7
inet addr:10.0.0.1 Bcast:10.255.255.255 Mask:255.0.0.0
inet6 addr: fe80::6038:e0ff:fe0c:37c7/64 Scope:Link
inet6 addr: fd17:1d32:4ab2::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:64290 errors:0 dropped:77 overruns:0 frame:0
TX packets:72099 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9624036 (9.1 MiB) TX bytes:186983172 (178.3 MiB)
eth0 Link encap:Ethernet HWaddr 62:38:E0:0C:37:C7
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1379910 errors:0 dropped:0 overruns:0 frame:0
TX packets:616507 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:793371683 (756.6 MiB) TX bytes:2025303471 (1.8 GiB)
Interrupt:35
eth1 Link encap:Ethernet HWaddr 60:38:E0:0C:37:C7
inet addr:###### Bcast:####### Mask:255.255.255.0
inet6 addr: fe80::6238:e0ff:####:37c7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2741030 errors:0 dropped:0 overruns:0 frame:0
TX packets:3337512 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:1681574708 (1.5 GiB) TX bytes:3130086026 (2.9 GiB)
Interrupt:37
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:5449 errors:0 dropped:0 overruns:0 frame:0
TX packets:5449 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:1189375 (1.1 MiB) TX bytes:1189375 (1.1 MiB)
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:1325719 errors:0 dropped:0 overruns:0 frame:0
TX packets:1506809 errors:0 dropped:4058 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:797798155 (760.8 MiB) TX bytes:1480978279 (1.3 GiB)
wlan0 Link encap:Ethernet HWaddr 62:38:E0:0C:37:C9
inet6 addr: fe80::6038:e0ff:fe0c:37c9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:31107 errors:0 dropped:0 overruns:0 frame:0
TX packets:54712 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6916366 (6.5 MiB) TX bytes:56252443 (53.6 MiB)
wlan1 Link encap:Ethernet HWaddr 62:38:E0:0C:37:C8
inet6 addr: fe80::6038:e0ff:fe0c:37c8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2697 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:462734 (451.8 KiB)
cat /etc/config/wireless
config wifi-device 'radio0'
option type 'mac80211'
option hwmode '11a'
option path 'soc/soc:pcie-controller/pci0000:00/0000:00:01.0/0000:01:00.0'
option channel '104'
option htmode 'VHT40'
option country 'SE'
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'lan'
option mode 'ap'
option macaddr '62:38:e0:0c:37:c9'
option encryption 'psk-mixed'
option key '#########'
option ssid 'geekinternatet'
config wifi-device 'radio1'
option type 'mac80211'
option hwmode '11g'
option path 'soc/soc:pcie-controller/pci0000:00/0000:00:02.0/0000:02:00.0'
option country 'SE'
option channel '8'
option distance '10'
config wifi-iface 'default_radio1'
option device 'radio1'
option network 'lan'
option mode 'ap'
option macaddr '62:38:e0:0c:37:c8'
option key '#######'
option encryption 'psk2'
option ieee80211w '0'
option ssid 'nerdinternatet'
opkg list-installed | grep mwlwifi
kmod-mwlwifi - 4.4.50+10.3.2.0-20170110-1
Anyone got a clue?