Hi @varu, thanks for the patch.
After a while I'm comming back to this project.
I flashed a firmware with it but I get no wan connectivity.
Did it finally work for you?
I finally made WAN work.
It seems the patch has some outdated dts properties and was not working correctly in master.
I sent a PR upstream to include the device in master.[
1 Like
Pleas can you upload the files to flash a new unit I recently bought?
@ogry, I uploaded the bin in the release of my repository
Can you test it and report.
Installation:
- Set host computer's ip to 192.168.10.100
- save sysupgrade image file as 'firmware.bin'
- setup tftp server on computer, serving the file from root
- connect your computer to the LAN port of the WAVLINK router via an Ethernet cable
- press and hold the reset button while powering on the router
- keep it pressed for ten seconds
- wait for firmware to be uploaded
Well, I don't know what else to do. I request help.
I have connected my PC with Debain 12 via a standard Ethernet cable to the LAN port of the router (I have also tried connecting it to the WAN port) The router is loaded with firmware M72HP3_V230525
I have configured the connection on the corresponding interface (enp0s31f6) with IPV4 at the fixed address 192.168.10.100/255.255.0.0 and without a gateway (it takes 192.168.10.1 by default)
I have configured a tftpd server to serve files from srv/tftp
I have copied to that directory the file that I have downloaded from the indicated repository (https://github.com/ianchi/openwrt/releases/download/wavlink1200-v0.1/openwrt-ramips-mt7620-wavlink_wl-wn572hg3-squashfs- sysupgrade.bin) by copying it with the name 'firmware.bin' to srv/tftp
I have also tried it with (https://downloads.openwrt.org/releases/23.05.4/targets/ramips/mt7621/openwrt-23.05.4-ramips-mt7621-wavlink_ws-wn572hp3-4g-initramfs-kernel.bin) , thinking it was an initial step.
I have verified that I can connect and download that file from the root with $ tftp 192.168.10.100 -c get firmware.bin
I initialize the router by keeping the reset button pressed for exactly 10 seconds after turning it on (I have tried from releasing it as soon as the lights come on to leaving it until they come back on for the second time).
I can't get Openwrt to load, it doesn't seem to change anything, after a couple of minutes, the WAVLINK-AC and WAVLINK-N SSIDs appear and I can only access the WAVLINK configuration page at https://192.168.10.1 to perform the initial configuration. Sometimes I have seen other SSIDs (WAVLINK, WAVLINK-MESH, and others)
What I can be doing wrong?
En domingo, 21 de abril de 2024, 04:38:39 CEST, AdriĆ”n Panella via OpenWrt Forum mail@forum.openwrt.org escribiĆ³:
| AdriƔn Panella ianchi
April 21 |
- | - |
@ogry, I uploaded the bin in the release of my repository
Can you test it and report.
Installation:- Set host computer's ip to 192.168.10.100
- save sysupgrade image file as 'firmware.bin'
- setup tftp server on computer, serving the file from root
- connect your computer to the LAN port of the WAVLINK router via an Ethernet cable
- press and hold the reset button while powering on the router
- keep it pressed for ten seconds
- wait for firmware to be uploaded
Definitely desperate, I renamed the firmware kernel file following the manufacturer's regulations, as WINSTAR_WN572HP3-A-R2-M72HP3_V230526-WO-4611b6e-GD_BY_FM and uploaded it to the corresponding interface. After restarting the status LED it keeps flashing very fast for quite some time. But nothing else happens, I'm afraid it has been blocked.
Frustrated, I'm already at the stage where I grab screwdrivers and socket wrenches and take everything apart.
Once I have the board, I reconnect the antennas, I don't want the delicate final amplifiers to be damaged.
I have soldered a connector to the serial port. In my experience it is the best way to be sure that the tracks will survive the many tests that lie ahead.
I am using a simple USB Serial with the everlasting PL2303 chip
Using TX-TX, RX-RX and connecting GND and +3.3V I get some lights to turn on, but it does not do the same as when it is turned on from the POE
In PuTTY, I connect it following the documentation. I only see garbage.
When it is connected and I turn on from POE I see that the converter heats up and disappears from the PC device list.
I remove the 3.3V connection, and leave only the data lines and ground.
Now, when I turn it on from the POE it initializes completely (well, at least some light turns on)
I change the configuration to 115200, 8n1
In the PuTTY console I finally see something I understand.
U-Boot SPL 2018.09-g4066fd9-dirty (Oct 19 2022 - 11:00:39 +0800)
Trying to boot from NOR
U-Boot 2018.09-g5ebaf91 (Oct 07 2023 - 09:29:04 +0800)
CPU: MediaTek MT7621AT ver 1, eco 3
Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz
Model: MediaTek MT7621 reference board
DRAM: 128 MiB
Loading Environment from SPI Flash... SF: Detected FM25Q128 with page size 256 B ytes, erase size 64 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
In: uartlite0@1e000c00
Out: uartlite0@1e000c00
Err: uartlite0@1e000c00
Net:
Warning: eth@1e100000 (eth0) using random MAC address - 5e:69:c8:f8:cf:5b
eth0: eth@1e100000
Hit any key to stop autoboot: 0
572HP3
gpio: pin 16 (gpio 16) value is 1
gpio: pin 17 (gpio 17) value is 1
gpio: pin 3 (gpio 3) value is 1
gpio: pin 17 (gpio 17) value is 0
gpio: pin 16 (gpio 16) value is 0
gpio: pin 3 (gpio 3) value is 0
gpio: pin 4 (gpio 4) value is 0
Timeout , no need to upgrade
do_winstar_upgrade lookup of <NULL> failed, check setup
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade bootloader
4. Upgrade bootloader (advanced mode)
5. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select
SF: Detected FM25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Reading from flash 0x50000 to mem 0x80010000, size 0x57f8b8 ...
## Loading kernel from FIT Image at 80010000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.15.162
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x800100e4
Data Size: 5752085 Bytes = 5.5 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Hash algo: crc32
Hash value: 78fb29c5
Hash algo: sha1
Hash value: 9cfd49f69cb3fe0c43668ff7f2e5768603e568ce
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 80010000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: MIPS OpenWrt wavlink_ws-wn572hp3-4g device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8058c744
Data Size: 11304 Bytes = 11 KiB
Architecture: MIPS
Hash algo: crc32
Hash value: a61515d8
Hash algo: sha1
Hash value: c895b8e6d8c488d9375f2c0e94810fcbd6db600d
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8058c744
Uncompressing Kernel Image ... OK
Loading Device Tree to 87e87000, end 87e8cc27 ... OK
[ 0.000000] Linux version 5.15.162 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU ld (GNU Bi nutils) 2.40.0) #0 SMP Mon Jul 15 22:14:18 2024
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Wavlink WS-WN572HP3 4G
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s17808 r8192 d23152 u49152
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00020e0e
[ 0.000000] Readback ErrCtl register=00020e0e
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 116388K/131072K available (7317K kernel code, 628K rwdata, 884K rodata, 4088K init, 225K bss, 14684K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008046] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066205] pid_max: default: 32768 minimum: 301
[ 0.071608] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.078822] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090302] rcu: Hierarchical SRCU implementation.
[ 0.095752] smp: Bringing up secondary CPUs ...
[ 0.101119] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101147] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.101161] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101205] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160495] Synchronize counters for CPU 1: done.
[ 0.192492] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.192515] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.192528] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.192558] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.251745] Synchronize counters for CPU 2: done.
[ 0.282415] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282439] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.282451] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282485] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.336946] Synchronize counters for CPU 3: done.
[ 0.366809] smp: Brought up 1 node, 4 CPUs
[ 0.375915] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.385714] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.392785] pinctrl core: initialized pinctrl subsystem
[ 0.399621] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.406241] thermal_sys: Registered thermal governor 'step_wise'
[ 0.431341] clocksource: Switched to clocksource GIC
[ 0.437754] NET: Registered PF_INET protocol family
[ 0.442805] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.450939] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.459260] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.466946] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.474557] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.481549] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.487983] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.494483] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.501794] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.507406] PCI: CLS 0 bytes, default 32
[ 0.522508] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.537243] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.543048] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.554845] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.018566] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.024756] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.030822] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.037158] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.043973] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.052776] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 1.060929] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.421430] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.428362] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.433231] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.438058] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.445303] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.451650] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.457061] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.463920] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.470076] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.476056] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.482298] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.488550] pci 0000:00:00.0: supports D1
[ 1.492507] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.499134] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.505143] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.511370] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.517634] pci 0000:00:01.0: supports D1
[ 1.521597] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.529094] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.537078] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.545315] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.551278] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.557672] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.565219] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.570382] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.576475] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.583214] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.590345] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.597325] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
[ 1.603354] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.610504] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.617720] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.625020] pci 0000:02:00.0: supports D1 D2
[ 1.629205] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.635846] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.652230] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.657397] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.663499] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.670199] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.677427] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.684043] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.690563] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.697587] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.704236] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.711142] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.717934] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.725145] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.731884] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref]
[ 1.739018] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
[ 1.745823] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
[ 1.752569] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.758577] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.764691] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 1.771439] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.776320] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.782431] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.789127] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.796356] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref]
[ 1.804066] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref]
[ 1.811774] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref]
[ 1.819440] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.824405] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.830418] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.837207] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
[ 1.846730] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.857446] printk: console [ttyS0] disabled
[ 1.861834] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.870831] printk: console [ttyS0] enabled
[ 1.870831] printk: console [ttyS0] enabled
[ 1.879137] printk: bootconsole [early0] disabled
[ 1.879137] printk: bootconsole [early0] disabled
[ 1.957410] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 1.964306] spi-nor spi0.0: unrecognized JEDEC id bytes: a1 40 18 a1 40 18
[ 1.971207] spi-nor: probe of spi0.0 failed with error -2
[ 2.103362] i2c_dev: i2c /dev entries driver
[ 2.110238] NET: Registered PF_INET6 protocol family
[ 2.117543] Segment Routing with IPv6
[ 2.121426] In-situ OAM (IOAM) with IPv6
[ 2.125483] NET: Registered PF_PACKET protocol family
[ 2.130706] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.144328] 8021q: 802.1Q VLAN Support v1.8
[ 2.413674] clk: Disabling unused clocks
[ 4.512089] Freeing unused kernel image (initmem) memory: 4088K
[ 4.518039] This architecture does not have kernel memory protection.
[ 4.524495] Run /init as init process
[ 5.042828] init: Console is alive
[ 5.046654] init: - watchdog -
[ 5.060615] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.075878] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.091280] init: - preinit -
[ 5.297860] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.379587] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.415067] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.768118] procd: - early -
[ 7.771242] procd: - watchdog -
[ 8.327272] procd: - watchdog -
[ 8.331165] procd: - ubus -
[ 8.341843] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.384174] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.391042] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.401480] procd: - init -
Please press Enter to activate this console.
[ 8.763732] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.824440] PPP generic driver version 2.4.2
[ 8.830256] NET: Registered PF_PPPOX protocol family
[ 8.842650] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 9.902384] urngd: v1.0.2 started.
[ 9.963929] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.073531] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.120148] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.799563] random: crng init done
[ 10.803096] random: 37 urandom warning(s) missed due to ratelimiting
^CPlease press Enter to activate this console.
BusyBox v1.36.1 (2024-07-15 22:14:18 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.4, r24012-d8dd03c46f
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ^C
root@OpenWrt:/# ^C
root@OpenWrt:/# ls -l
drwxr-xr-x 2 root root 1220 Jul 15 22:14 bin
drwxr-xr-x 3 root root 860 Jul 15 22:14 dev
drwxr-xr-x 23 root root 1260 Jul 15 22:14 etc
-rwxr-xr-x 1 root root 276 Jul 15 22:14 init
drwxr-xr-x 10 root root 520 Jul 15 22:14 lib
drwxr-xr-x 2 root root 40 Jul 15 22:14 mnt
drwxr-xr-x 2 root root 40 Jul 15 22:14 overlay
dr-xr-xr-x 118 root root 0 Jan 1 1970 proc
drwxr-xr-x 2 root root 60 Jul 15 22:14 rom
drwxr-xr-x 2 root root 40 Jul 15 22:14 root
drwxr-xr-x 2 root root 1180 Jul 15 22:14 sbin
dr-xr-xr-x 11 root root 0 Jan 1 1970 sys
drwxrwxrwt 15 root root 400 Jul 15 22:14 tmp
drwxr-xr-x 7 root root 140 Jul 15 22:14 usr
lrwxrwxrwx 1 root root 3 Jan 1 1970 var -> tmp
drwxr-xr-x 4 root root 100 Jul 15 22:14 www
root@OpenWrt:/# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:640 errors:0 dropped:0 overruns:0 frame:0
TX packets:640 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:49920 (48.7 KiB) TX bytes:49920 (48.7 KiB)
root@OpenWrt:/#ls www
cgi-bin index.html luci-static
root@OpenWrt:/#
I still have to get it to fully charge and communicate with the network, but the road is promising.
I have the same problem, I can't put the
OPENWRT for nothing I've been trying for a few hours.
I just successfully tftpbooted and flashed this pre-release on my WL-572HG3 REV.A router. Following the steps noted above it booted just fine, although only ssh worked in the tftpbooted image. LuCI only worked after flashing. Keep in mind that you need v0.2 because in v0.1 you cannot ssh into the router as it does not allow empty passwords.
Here is how I did it:
- Downloaded
v0.2 - Renamed to
firmware.bin - set static IP (IP:
192.168.10.100, Netmask:24Gateway:192.168.10.1) - served over tftp using tftpd-hpa
- held reset button for more than 10 seconds while powering on and serving over tftp
- waited a minute while serving image over tftp after releasing reset button
- changed static IP (IP:
192.168.1.100, Netmask:24Gateway:192.168.1.1) - disconnected and reconnected the computer
- was able to
ping 192.168.1.1now - was able to
ssh root@192.168.1.1now - used ssh to transfer the image using command
cat firmware.bin | ssh root@192.168.1.1 -C "cat > /tmp/firmware.bin" - campared md5sum (
md5sum firmware.binon the Computer has to give the same output asmd5sum /tmp/firmware.binon the ssh command line on OpenWRT), in my cased4b30e1f70189a74bd3a8b6f1b159778 /tmp/firmware.bin - flashed with
sysupgrade -n /tmp/firmware.binwhich immediately closes all connections and takes quite a while, the power was on while the highest wifi signal led was blinking - As soon as more LEDs lighted up again I could reconnect to my flashed OpenWRT router where not only ssh but also LuCI was working
EDIT: I have not jet tested if everything works, just successfully flashed and booted it, used ssh and LuCI. Be careful as this is a pre-release, it is still work in progress.
I recently received a WL-WN572HP3, and I was wondering if anyone has successfully installed OpenWRT on this model. I know this discussion is about WL-WN572HG3, and it seems like they might be similar, but I canāt confirm the exact hardware specs at the moment
Unfortunately, I donāt have physical access to the device right now to open it up and check the chipset, but as soon as I can, I will do that. In the meantime, has anyone tried flashing OpenWRT on WN572HP3?
P.S. I just contacted Wavlink support and asked them directly about the technical differences between WL-WN572HP3 and WL-WN572HG3, specifically regarding the processor, flash memory, RAM, and other hardware details. As soon as they reply, Iāll be able to confirm or disprove whether the two versions are identical
Hereās what they told me:
-
Chipset:
- WN572HP3: MT7621A
- WN572HG3: MT7620
-
Flash Memory:
- WN572HP3: 128MB
- WN572HG3: 64MB
-
Ethernet Ports:
- WN572HP3: Two gigabit Ethernet ports
- WN572HG3: One gigabit WAN + one 100Mbps LAN
-
Operating Modes:
- WN572HP3: AP, repeater, router, and mesh mode
- WN572HG3: AP, repeater, and router mode
So it looks like there are some significant differences between the two models. I'm going to check chip specifications to find out if there is a compatible model that already supports OpenWRT, to try to build the firmware.
P.S.: I found a discussion specifically about my model: OpenWRT support for WL-WN572HP3.
From what I understand, WS-WN572HP3 4G and WL-WN572HP3 are almost identical, except that the WS-WN572HP3 4G version has an LTE modem, which my model doesnāt have
Since OpenWRT is already available for WS-WN572HP3 4G, it might be possible to use the same firmware on WL-WN572HP3. To free up space, unnecessary 4G-related packages like:
kmod-usb3kmod-usb-net-rndiscomgt-ncm
Do you still have it easily available? I currently have it attached using the stock firmware to a managed switch but was thinking of adding it to my mesh network, but canāt figure out if it has 802.1s mesh capabilities once the correct WPAD is installed or 802.1r for fast roaming. If you can easily access the device still I was wondering if you might have a look first before I have a go with your instructions. I donāt think unencrypted meshes need any specific WPAD but havenāt ever had a look before installing WPAD-Mesh-SSH instead of the basic one used by default in OpenWRT.
Are You working on this project, any update in the future?
I have 2 Wavlink successfully flashed with Your posted method and all worked OK except software manager, here is not possible to update or install any package.
Thanks