Thank you a lot for all the information. I do some more research if I am inside 
I proudly present:
1 Like
OK I got it running!
I simply took a random firmware with the same CPU from:
and flashed it with UART and uBoot:
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
I works without 5 GHz WiFi because the firmware simply does not cover the MT7612EN.
This might be a perfect start for somebody who knows what to do next. 
Is there somebody to direct me in the right direction?
The documentation is a bit better in the Wiki now and this could help too.
That's awesome! Let me setup a builder machine and we can get that 5g resolved.
Post the UART boot log please.
Nevermind I see it in the WIKI
No that are yours. Just a second. I create one just now.
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
4 3 2 1 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.195
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1565650 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:17e3d2
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.195 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11208-ce6496d796)) #0 Sun Sep 6 16:19:39 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Asus RP-N53
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from 0x80481740 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000002
[ 0.000000] Readback ErrCtl register=00000002
[ 0.000000] Memory: 58808K/65536K available (3918K kernel code, 185K rwdata, 500K rodata, 1212K init, 215K bss, 6728K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015487] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087729] pid_max: default: 32768 minimum: 301
[ 0.097144] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110174] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130474] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149953] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.162125] pinctrl core: initialized pinctrl subsystem
[ 0.173724] NET: Registered protocol family 16
[ 0.440794] PCI host bridge /pcie@10140000 ranges:
[ 0.450196] MEM 0x0000000020000000..0x000000002fffffff
[ 0.460567] IO 0x0000000010160000..0x000000001016ffff
[ 0.488319] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.499364] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.511959] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.522960] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.536056] PCI host bridge to bus 0000:00
[ 0.544056] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.557769] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.569502] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.583002] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.599224] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.615795] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.628856] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.642664] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.656165] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.670529] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.684037] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.698583] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.712930] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.722785] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.736297] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.754967] clocksource: Switched to clocksource systick
[ 0.766656] NET: Registered protocol family 2
[ 0.776210] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.789988] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.802579] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.815349] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.826872] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.839551] NET: Registered protocol family 1
[ 0.850849] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.863589] Crashlog allocated RAM at address 0x3f00000
[ 0.875662] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.894377] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.905879] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.935642] io scheduler noop registered
[ 0.943286] io scheduler deadline registered (default)
[ 0.954473] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.969879] console [ttyS0] disabled
[ 0.976940] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.996609] console [ttyS0] enabled
[ 0.996609] console [ttyS0] enabled
[ 1.010422] bootconsole [early0] disabled
[ 1.010422] bootconsole [early0] disabled
[ 1.034141] spi spi0.0: force spi mode3
[ 1.044465] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 1.053769] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.066438] Creating 4 MTD partitions on "spi0.0":
[ 1.076002] 0x000000000000-0x000000030000 : "u-boot"
[ 1.086832] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.098358] 0x000000040000-0x000000050000 : "factory"
[ 1.109329] 0x000000050000-0x000000800000 : "firmware"
[ 1.123329] 2 uimage-fw partitions found on MTD device firmware
[ 1.135196] Creating 2 MTD partitions on "firmware":
[ 1.145109] 0x000000000000-0x00000017e412 : "kernel"
[ 1.155915] 0x00000017e412-0x0000007b0000 : "rootfs"
[ 1.166666] mtd: device 5 (rootfs) set to be root filesystem
[ 1.179524] 1 squashfs-split partitions found on MTD device rootfs
[ 1.191912] 0x0000003c0000-0x0000007b0000 : "rootfs_data"
[ 1.204392] libphy: Fixed MDIO Bus: probed
[ 1.221365] gsw: setting port4 to ephy mode
[ 1.229776] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
[ 1.248012] mtk_soc_eth 10100000.ethernet: generated random MAC address 82:66:bd:c8:ad:04
[ 1.264395] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.276888] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.293913] rt2880_wdt 10000120.watchdog: Initialized
[ 1.305437] NET: Registered protocol family 10
[ 1.318377] Segment Routing with IPv6
[ 1.325861] NET: Registered protocol family 17
[ 1.334760] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.360606] 8021q: 802.1Q VLAN Support v1.8
[ 1.386598] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.407325] Freeing unused kernel memory: 1212K
[ 1.416373] This architecture does not have kernel memory protection.
[ 2.774939] random: fast init done
[ 3.064455] init: Console is alive
[ 3.071576] init: - watchdog -
[ 4.713656] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.799785] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.818370] init: - preinit -
[ 6.365611] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.224911] jffs2: notice: (386) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[ 8.258511] mount_root: switching to jffs2 overlay
[ 8.297348] overlayfs: upper fs does not support tmpfile.
[ 8.318055] urandom-seed: Seeding with /etc/urandom.seed
[ 8.455690] procd: - early -
[ 8.461549] procd: - watchdog -
[ 8.805379] procd: - watchdog -
[ 8.812080] procd: - ubus -
[ 9.054095] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.138902] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.152200] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.166077] procd: - init -
Please press Enter to activate this console.
[ 9.994021] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.164090] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.202976] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6
[ 10.218317] Backport generated by backports.git v4.19.137-1-0-g60c3a249
[ 10.268958] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.303420] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 10.441369] xt_time: kernel timezone is -0000
[ 10.494945] urngd: jent-rng init failed, err: 2
[ 10.543181] PPP generic driver version 2.4.2
[ 10.554655] NET: Registered protocol family 24
[ 10.597067] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 10.611530] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 10.627000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 10.738852] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 22.899192] 8021q: adding VLAN 0 to HW filter on device eth0
[ 22.953430] device eth0 entered promiscuous mode
[ 22.981263] br-lan: port 1(eth0.1) entered blocking state
[ 22.992101] br-lan: port 1(eth0.1) entered disabled state
[ 23.003259] device eth0.1 entered promiscuous mode
[ 23.112101] br-lan: port 1(eth0.1) entered blocking state
[ 23.122931] br-lan: port 1(eth0.1) entered forwarding state
[ 23.134282] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 23.906854] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 19.07.4, r11208-ce6496d796
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# greetings to frustro
1 Like
I am pretty sure I have enough rest to think better than 20 hours ago.
Since the RP-N53 boots, I'm am going to use the builder tool on v19.07.3 Less errors with slower maintained packages.
So we will have a builder@ap-builder made N53 image. Then we need to verify it boots and is limited to just the 2.4 radio.
Then I/you/we can modify that template and throw all of the the MT76X and RT/RA28XX drivers, firmware and everything. Hopefully we get the 5g working!
From there we can figure out what we do and do not need and tune/optimize,
What do you think of that @muebau?
virgin no modification template build for that asus is Here
I'm building all the other raMT targets right now with no mods changes to the template.
I'm also getting one of these device back in the shop soon so I can help devel more than just building .
mt7620 variety are complete.
wow very impressive
What do you think of that @muebau?
Yes I thought the same.
result: boot loop
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a_mt7610e-squashfs-sysupgrade.bin
sha256sum firmware.bin
7ea3f658c34024620bef59319e37959b15c9dcab570988c0c04bc1e60afd54ad firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
4 3 2 1 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1593575 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1850e7
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620A evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=000452d2
[ 0.000000] Readback ErrCtl register=000452d2
[ 0.000000] Memory: 58688K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 1196K init, 208K bss, 6848K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015469] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087723] pid_max: default: 32768 minimum: 301
[ 0.097130] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110157] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130097] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149577] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161757] pinctrl core: initialized pinctrl subsystem
[ 0.172607] NET: Registered protocol family 16
[ 0.184170] rt2880-pinmux pinctrl: error claiming hogs: -22
[ 0.195157] rt2880-pinmux pinctrl: could not claim hogs: -22
[ 0.206462] rt2880-pinmux: probe of pinctrl failed with error -22
[ 0.223818] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 0.258287] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.269331] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.285271] clocksource: Switched to clocksource systick
[ 0.296938] NET: Registered protocol family 2
[ 0.306366] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.320145] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.332740] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.345526] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.357050] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.369739] NET: Registered protocol family 1
[ 0.380984] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.393715] Crashlog allocated RAM at address 0x3f00000
[ 0.405796] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.424350] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.435856] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.465374] io scheduler noop registered
[ 0.473019] io scheduler deadline registered (default)
[ 0.484067] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.497380] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 0.517695] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 0.537006] libphy: Fixed MDIO Bus: probed
[ 0.546384] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 0.565710] rt2880_wdt 10000120.watchdog: Initialized
[ 0.577013] NET: Registered protocol family 10
[ 0.596131] Segment Routing with IPv6
[ 0.603359] NET: Registered protocol family 17
[ 0.612214] 8021q: 802.1Q VLAN Support v1.8
[ 0.621034] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 0.639278] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 0.658671] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 0.677349] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 0.697687] Warning: unable to open an initial console.
[ 0.708730] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.723529] Please append a correct "root=" boot option; here are the available partitions:
[ 0.740108] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 0.757377] Rebooting in 1 seconds..
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
\00\00
result: freeze
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a_mt7610e-initramfs-kernel.bin
sha256sum firmware.bin
e03255c67dbe937c330ef9bc6b59e11bd084f592511faaf78aaa039f233794c7 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.10.101) ==:192.168.10.101
Input server IP (192.168.10.100) ==:192.168.10.100
Input Linux Kernel filename (firmware.bin) ==:firmware.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.10.100; our IP address is 192.168.10.101
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Loading: *Got ARP REPLY, set server/gtwy eth addr (00:e0:4c:68:80:7e)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############################
done
Bytes transferred = 3482711 (352457 hex)
LoadAddr=82000000 NetBootFileXferSize= 00352457
raspi_erase_write: offs:50000, count:352457
raspi_erase: offs:50000 len:350000
.....................................................
raspi_write: to:50000 len:350000
.....................................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_read: from:70000 len:10000
raspi_read: from:80000 len:10000
raspi_read: from:90000 len:10000
raspi_read: from:a0000 len:10000
raspi_read: from:b0000 len:10000
raspi_read: from:c0000 len:10000
raspi_read: from:d0000 len:10000
raspi_read: from:e0000 len:10000
raspi_read: from:f0000 len:10000
raspi_read: from:100000 len:10000
raspi_read: from:110000 len:10000
raspi_read: from:120000 len:10000
raspi_read: from:130000 len:10000
raspi_read: from:140000 len:10000
raspi_read: from:150000 len:10000
raspi_read: from:160000 len:10000
raspi_read: from:170000 len:10000
raspi_read: from:180000 len:10000
raspi_read: from:190000 len:10000
raspi_read: from:1a0000 len:10000
raspi_read: from:1b0000 len:10000
raspi_read: from:1c0000 len:10000
raspi_read: from:1d0000 len:10000
raspi_read: from:1e0000 len:10000
raspi_read: from:1f0000 len:10000
raspi_read: from:200000 len:10000
raspi_read: from:210000 len:10000
raspi_read: from:220000 len:10000
raspi_read: from:230000 len:10000
raspi_read: from:240000 len:10000
raspi_read: from:250000 len:10000
raspi_read: from:260000 len:10000
raspi_read: from:270000 len:10000
raspi_read: from:280000 len:10000
raspi_read: from:290000 len:10000
raspi_read: from:2a0000 len:10000
raspi_read: from:2b0000 len:10000
raspi_read: from:2c0000 len:10000
raspi_read: from:2d0000 len:10000
raspi_read: from:2e0000 len:10000
raspi_read: from:2f0000 len:10000
raspi_read: from:300000 len:10000
raspi_read: from:310000 len:10000
raspi_read: from:320000 len:10000
raspi_read: from:330000 len:10000
raspi_read: from:340000 len:10000
raspi_read: from:350000 len:10000
raspi_read: from:360000 len:10000
raspi_read: from:370000 len:10000
raspi_read: from:380000 len:10000
raspi_read: from:390000 len:10000
raspi_read: from:3a0000 len:10000
raspi_erase: offs:3a0000 len:10000
.
raspi_write: to:3a0000 len:10000
.
raspi_read: from:3a0000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3482647 Bytes = 3.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:352417
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620A evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00045282
[ 0.000000] Readback ErrCtl register=00045282
[ 0.000000] Memory: 56832K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 3052K init, 208K bss, 8704K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087728] pid_max: default: 32768 minimum: 301
[ 0.097133] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110160] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130107] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149587] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161766] pinctrl core: initialized pinctrl subsystem
[ 0.172618] NET: Registered protocol family 16
[ 0.184182] rt2880-pinmux pinctrl: error claiming hogs: -22
[ 0.195170] rt2880-pinmux pinctrl: could not claim hogs: -22
[ 0.206476] rt2880-pinmux: probe of pinctrl failed with error -22
[ 0.223829] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 0.258312] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.269355] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.285292] clocksource: Switched to clocksource systick
[ 0.296949] NET: Registered protocol family 2
[ 0.306378] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.320157] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.332752] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.345540] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.357063] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.369753] NET: Registered protocol family 1
[ 2.655292] random: fast init done
[ 3.728490] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 3.741210] Crashlog allocated RAM at address 0x3f00000
[ 3.753204] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 3.771695] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.783197] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.882791] io scheduler noop registered
[ 3.890501] io scheduler deadline registered (default)
[ 3.901468] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 3.914808] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 3.935118] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 3.954416] libphy: Fixed MDIO Bus: probed
[ 3.963782] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 3.983110] rt2880_wdt 10000120.watchdog: Initialized
[ 3.994415] NET: Registered protocol family 10
[ 4.013444] Segment Routing with IPv6
[ 4.020749] NET: Registered protocol family 17
[ 4.029504] 8021q: 802.1Q VLAN Support v1.8
[ 4.038368] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 4.056610] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 4.075998] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 4.094674] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 4.115030] Warning: unable to open an initial console.
[ 4.141917] Freeing unused kernel memory: 3052K
[ 4.150796] This architecture does not have kernel memory protection.
[ 4.177411] init: Console is alive
[ 4.184260] init: - watchdog -
[ 4.214090] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.229249] gpio-keys keys: unable to claim gpio 12, err=-517
[ 4.243111] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.259439] init: - preinit -
[ 6.596356] procd: - early -
[ 6.602798] procd: - watchdog -
[ 6.694743] procd: - watchdog -
[ 6.701123] procd: failed to set stdio: No such device
[ 6.711345] procd: - ubus -
[ 6.723998] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.740710] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.753787] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.767326] procd: - init -
[ 7.234857] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.276924] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.323076] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 7.338228] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 7.382915] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.415745] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.555198] xt_time: kernel timezone is -0000
[ 7.675840] PPP generic driver version 2.4.2
[ 7.701306] NET: Registered protocol family 24
[ 7.774851] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 7.807848] urngd: jent-rng init failed, err: 2
[ 7.820864] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 7.838961] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.903617] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[ 7.918108] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.934852] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.973576] kmodloader: done loading kernel modules from /etc/modules.d/*
0.440138] PCI host bridge /pcie@10140000 ranges:
[ 0.449542] MEM 0x0000000020000000..0x000000002fffffff
[ 0.459911] IO 0x0000000010160000..0x000000001016ffff
in the pastebin of mine and your oem bootlog is what it is missing, need to see that asus one i made boot with debug please
result: boot loop
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a_v22sg-squashfs-sysupgrade.bin
sha256sum firmware.bin
e2d7f2afbadb0b7891c05e32eb89d1ec4228eb364f9f0c0cdb1c7ee62d45b379 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.10.101) ==:192.168.10.101
Input server IP (192.168.10.100) ==:192.168.10.100
Input Linux Kernel filename (firmware.bin) ==:firmware.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.10.100; our IP address is 192.168.10.101
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Loading: *Got ARP REPLY, set server/gtwy eth addr (00:e0:4c:68:80:7e)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############################
done
Bytes transferred = 3482711 (352457 hex)
LoadAddr=82000000 NetBootFileXferSize= 00352457
raspi_erase_write: offs:50000, count:352457
raspi_erase: offs:50000 len:350000
.....................................................
raspi_write: to:50000 len:350000
.....................................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_read: from:70000 len:10000
raspi_read: from:80000 len:10000
raspi_read: from:90000 len:10000
raspi_read: from:a0000 len:10000
raspi_read: from:b0000 len:10000
raspi_read: from:c0000 len:10000
raspi_read: from:d0000 len:10000
raspi_read: from:e0000 len:10000
raspi_read: from:f0000 len:10000
raspi_read: from:100000 len:10000
raspi_read: from:110000 len:10000
raspi_read: from:120000 len:10000
raspi_read: from:130000 len:10000
raspi_read: from:140000 len:10000
raspi_read: from:150000 len:10000
raspi_read: from:160000 len:10000
raspi_read: from:170000 len:10000
raspi_read: from:180000 len:10000
raspi_read: from:190000 len:10000
raspi_read: from:1a0000 len:10000
raspi_read: from:1b0000 len:10000
raspi_read: from:1c0000 len:10000
raspi_read: from:1d0000 len:10000
raspi_read: from:1e0000 len:10000
raspi_read: from:1f0000 len:10000
raspi_read: from:200000 len:10000
raspi_read: from:210000 len:10000
raspi_read: from:220000 len:10000
raspi_read: from:230000 len:10000
raspi_read: from:240000 len:10000
raspi_read: from:250000 len:10000
raspi_read: from:260000 len:10000
raspi_read: from:270000 len:10000
raspi_read: from:280000 len:10000
raspi_read: from:290000 len:10000
raspi_read: from:2a0000 len:10000
raspi_read: from:2b0000 len:10000
raspi_read: from:2c0000 len:10000
raspi_read: from:2d0000 len:10000
raspi_read: from:2e0000 len:10000
raspi_read: from:2f0000 len:10000
raspi_read: from:300000 len:10000
raspi_read: from:310000 len:10000
raspi_read: from:320000 len:10000
raspi_read: from:330000 len:10000
raspi_read: from:340000 len:10000
raspi_read: from:350000 len:10000
raspi_read: from:360000 len:10000
raspi_read: from:370000 len:10000
raspi_read: from:380000 len:10000
raspi_read: from:390000 len:10000
raspi_read: from:3a0000 len:10000
raspi_erase: offs:3a0000 len:10000
.
raspi_write: to:3a0000 len:10000
.
raspi_read: from:3a0000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3482647 Bytes = 3.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:352417
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620A evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00045282
[ 0.000000] Readback ErrCtl register=00045282
[ 0.000000] Memory: 56832K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 3052K init, 208K bss, 8704K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087728] pid_max: default: 32768 minimum: 301
[ 0.097133] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110160] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130107] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149587] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161766] pinctrl core: initialized pinctrl subsystem
[ 0.172618] NET: Registered protocol family 16
[ 0.184182] rt2880-pinmux pinctrl: error claiming hogs: -22
[ 0.195170] rt2880-pinmux pinctrl: could not claim hogs: -22
[ 0.206476] rt2880-pinmux: probe of pinctrl failed with error -22
[ 0.223829] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 0.258312] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.269355] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.285292] clocksource: Switched to clocksource systick
[ 0.296949] NET: Registered protocol family 2
[ 0.306378] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.320157] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.332752] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.345540] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.357063] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.369753] NET: Registered protocol family 1
[ 2.655292] random: fast init done
[ 3.728490] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 3.741210] Crashlog allocated RAM at address 0x3f00000
[ 3.753204] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 3.771695] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.783197] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.882791] io scheduler noop registered
[ 3.890501] io scheduler deadline registered (default)
[ 3.901468] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 3.914808] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 3.935118] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 3.954416] libphy: Fixed MDIO Bus: probed
[ 3.963782] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 3.983110] rt2880_wdt 10000120.watchdog: Initialized
[ 3.994415] NET: Registered protocol family 10
[ 4.013444] Segment Routing with IPv6
[ 4.020749] NET: Registered protocol family 17
[ 4.029504] 8021q: 802.1Q VLAN Support v1.8
[ 4.038368] mt7620-pci 10140000.pcie: could not find pctldev for node /pinctrl/pcie, deferring probe
[ 4.056610] of_serial 10000c00.uartlite: could not find pctldev for node /pinctrl/uartlite, deferring probe
[ 4.075998] spi-rt2880 10000b00.spi: could not find pctldev for node /pinctrl/spi_pins, deferring probe
[ 4.094674] mtk_soc_eth 10100000.ethernet: could not find pctldev for node /pinctrl/ephy, deferring probe
[ 4.115030] Warning: unable to open an initial console.
[ 4.141917] Freeing unused kernel memory: 3052K
[ 4.150796] This architecture does not have kernel memory protection.
[ 4.177411] init: Console is alive
[ 4.184260] init: - watchdog -
[ 4.214090] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.229249] gpio-keys keys: unable to claim gpio 12, err=-517
[ 4.243111] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.259439] init: - preinit -
[ 6.596356] procd: - early -
[ 6.602798] procd: - watchdog -
[ 6.694743] procd: - watchdog -
[ 6.701123] procd: failed to set stdio: No such device
[ 6.711345] procd: - ubus -
[ 6.723998] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.740710] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.753787] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.767326] procd: - init -
[ 7.234857] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.276924] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.323076] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 7.338228] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 7.382915] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.415745] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.555198] xt_time: kernel timezone is -0000
[ 7.675840] PPP generic driver version 2.4.2
[ 7.701306] NET: Registered protocol family 24
[ 7.774851] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 7.807848] urngd: jent-rng init failed, err: 2
[ 7.820864] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 7.838961] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.903617] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[ 7.918108] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.934852] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.973576] kmodloader: done loading kernel modules from /etc/modules.d/*
result: boot loop
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a_v22sg-initramfs-kernel.bin
sha256sum firmware.bin
fe8f971aa6d400d0dacf75dc2185db5a86b2e91342acfbcef6b2b53f7f945284 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.10.101) ==:192.168.10.101
Input server IP (192.168.10.100) ==:192.168.10.100
Input Linux Kernel filename (firmware.bin) ==:firmware.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.10.100; our IP address is 192.168.10.101
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Loading: *Got ARP REPLY, set server/gtwy eth addr (00:e0:4c:68:80:7e)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############################
done
Bytes transferred = 3482717 (35245d hex)
LoadAddr=82000000 NetBootFileXferSize= 0035245d
raspi_erase_write: offs:50000, count:35245d
raspi_erase: offs:50000 len:350000
.....................................................
raspi_write: to:50000 len:350000
.....................................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_read: from:70000 len:10000
raspi_read: from:80000 len:10000
raspi_read: from:90000 len:10000
raspi_read: from:a0000 len:10000
raspi_read: from:b0000 len:10000
raspi_read: from:c0000 len:10000
raspi_read: from:d0000 len:10000
raspi_read: from:e0000 len:10000
raspi_read: from:f0000 len:10000
raspi_read: from:100000 len:10000
raspi_read: from:110000 len:10000
raspi_read: from:120000 len:10000
raspi_read: from:130000 len:10000
raspi_read: from:140000 len:10000
raspi_read: from:150000 len:10000
raspi_read: from:160000 len:10000
raspi_read: from:170000 len:10000
raspi_read: from:180000 len:10000
raspi_read: from:190000 len:10000
raspi_read: from:1a0000 len:10000
raspi_read: from:1b0000 len:10000
raspi_read: from:1c0000 len:10000
raspi_read: from:1d0000 len:10000
raspi_read: from:1e0000 len:10000
raspi_read: from:1f0000 len:10000
raspi_read: from:200000 len:10000
raspi_read: from:210000 len:10000
raspi_read: from:220000 len:10000
raspi_read: from:230000 len:10000
raspi_read: from:240000 len:10000
raspi_read: from:250000 len:10000
raspi_read: from:260000 len:10000
raspi_read: from:270000 len:10000
raspi_read: from:280000 len:10000
raspi_read: from:290000 len:10000
raspi_read: from:2a0000 len:10000
raspi_read: from:2b0000 len:10000
raspi_read: from:2c0000 len:10000
raspi_read: from:2d0000 len:10000
raspi_read: from:2e0000 len:10000
raspi_read: from:2f0000 len:10000
raspi_read: from:300000 len:10000
raspi_read: from:310000 len:10000
raspi_read: from:320000 len:10000
raspi_read: from:330000 len:10000
raspi_read: from:340000 len:10000
raspi_read: from:350000 len:10000
raspi_read: from:360000 len:10000
raspi_read: from:370000 len:10000
raspi_read: from:380000 len:10000
raspi_read: from:390000 len:10000
raspi_read: from:3a0000 len:10000
raspi_erase: offs:3a0000 len:10000
.
raspi_write: to:3a0000 len:10000
.
raspi_read: from:3a0000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3482653 Bytes = 3.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:35241d
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620a V22SG High Power evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00045282
[ 0.000000] Readback ErrCtl register=00045282
[ 0.000000] Memory: 56832K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 3052K init, 208K bss, 8704K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015469] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087727] pid_max: default: 32768 minimum: 301
[ 0.097132] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110159] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130184] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149670] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161844] pinctrl core: initialized pinctrl subsystem
[ 0.172691] NET: Registered protocol family 16
[ 0.442721] PCI host bridge /pcie@10140000 ranges:
[ 0.452111] MEM 0x0000000020000000..0x000000002fffffff
[ 0.462498] IO 0x0000000010160000..0x000000001016ffff
[ 0.489845] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.500885] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.513964] PCI host bridge to bus 0000:00
[ 0.521963] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.535683] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.547416] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.560915] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.577147] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.593692] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.606749] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.620567] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.634068] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.648432] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.661942] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.676491] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.690835] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.700680] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.714199] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.732260] clocksource: Switched to clocksource systick
[ 0.743938] NET: Registered protocol family 2
[ 0.753384] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.767165] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.779757] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.792544] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.804068] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.816746] NET: Registered protocol family 1
[ 2.722276] random: fast init done
[ 4.176183] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 4.188893] Crashlog allocated RAM at address 0x3f00000
[ 4.200910] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 4.219402] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.230906] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.330434] io scheduler noop registered
[ 4.338145] io scheduler deadline registered (default)
[ 4.349138] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 4.362800] console [ttyS0] disabled
[ 4.369793] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 4.389565] console [ttyS0] enabled
[ 4.389565] console [ttyS0] enabled
[ 4.403352] bootconsole [early0] disabled
[ 4.403352] bootconsole [early0] disabled
[ 4.421143] libphy: Fixed MDIO Bus: probed
[ 4.439912] gsw: setting port4 to gmac mode
[ 4.448328] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
[ 4.466571] mtk_soc_eth 10100000.ethernet: generated random MAC address e2:76:97:4a:df:57
[ 4.483060] libphy: mdio: probed
[ 4.513601] mdio_bus mdio-bus: MDIO device at address 5 is missing.
[ 4.526438] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=001cc916, driver=Generic PHY]
[ 4.547550] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 4.560016] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 4.577019] rt2880_wdt 10000120.watchdog: Initialized
[ 4.588482] NET: Registered protocol family 10
[ 4.601604] Segment Routing with IPv6
[ 4.609101] NET: Registered protocol family 17
[ 4.618035] 8021q: 802.1Q VLAN Support v1.8
[ 4.645402] Freeing unused kernel memory: 3052K
[ 4.654466] This architecture does not have kernel memory protection.
[ 4.680917] init: Console is alive
[ 4.688133] init: - watchdog -
[ 4.718278] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.736491] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.752783] init: - preinit -
[ 4.953491] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.965209] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.976992] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.149793] CPU 0 Unable to handle kernel paging request at virtual address 0000017c, epc == 8024f9a4, ra == 8023c358
[ 5.170943] Oops[#1]:
[ 5.175464] CPU: 0 PID: 122 Comm: kworker/0:1 Not tainted 4.14.180 #0
[ 5.188312] Workqueue: events_power_efficient phy_state_machine
[ 5.200100] task: 83986d00 task.stack: 839da000
[ 5.209110] $ 0 : 00000000 00000001 8049c584 00000000
[ 5.219519] $ 4 : 00000024 8049c570 00000000 00000000
[ 5.229926] $ 8 : 839dbfe0 0000a400 00000000 004c79ad
[ 5.240335] $12 : 00000000 5fef1a53 00000000 00000000
[ 5.250743] $16 : 00000005 8381bd48 8381b800 00000064
[ 5.261150] $20 : 000003e8 00000001 0000000a 8381bc60
[ 5.271557] $24 : 8047d040 8024f938
[ 5.281965] $28 : 839da000 839dbe10 80480000 8023c358
[ 5.292377] Hi : 004c79ad
[ 5.298099] Lo : bb8d6c1c
[ 5.303853] epc : 8024f9a4 fe_phy_link_adjust+0x6c/0x198
[ 5.314774] ra : 8023c358 phy_state_machine+0x3f8/0x5c0
[ 5.325688] Status: 1100a402 KERNEL EXL
[ 5.333498] Cause : 00800008 (ExcCode 02)
[ 5.341472] BadVA : 0000017c
[ 5.347196] PrId : 00019650 (MIPS 24KEc)
[ 5.355167] Modules linked in: leds_gpio gpio_button_hotplug
[ 5.366446] Process kworker/0:1 (pid: 122, threadinfo=839da000, task=83986d00, tls=00000000)
[ 5.383245] Stack : 00000000 00000000 00000000 8023e4bc 00000000 8393b5b4 8393b400 8393b5e8
[ 5.399894] 8108c500 00000000 00000000 80490000 fffffffe 8023c358 00000001 8392d880
[ 5.416543] 00000000 8003b308 8393b5b4 8392d880 00000000 8108c500 00000000 8003bcd4
[ 5.433191] 80485314 80485198 80490000 80485314 80490000 fffffffe 8392d880 80485184
[ 5.449841] 8392d898 80485198 80490000 80485314 80490000 8003c1a0 807a0000 804957c0
[ 5.466490] ...
[ 5.471351] Call Trace:
[ 5.476216] [<8024f9a4>] fe_phy_link_adjust+0x6c/0x198
[ 5.486449] [<8023c358>] phy_state_machine+0x3f8/0x5c0
[ 5.496697] [<8003bcd4>] process_one_work+0x26c/0x418
[ 5.506754] [<8003c1a0>] worker_thread+0x320/0x56c
[ 5.516297] [<80041574>] kthread+0x128/0x13c
[ 5.524804] [<80005a98>] ret_from_kernel_thread+0x14/0x1c
[ 5.535554] Code: 10600028 00000000 8c430000 <8c65017c> 10a00009 8c64016c 8c470060 8c660170 14e60007
[ 5.554986]
[ 5.558015] ---[ end trace d1d38da08fbdddfa ]---
[ 5.568755] Kernel panic - not syncing: Fatal exception
[ 5.580154] Rebooting in 1 seconds..
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:FFFF ID1:1C!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
4 3 2 \00\00
result: boot loop
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a-squashfs-sysupgrade.bin
sha256sum firmware.bin
c791fd12fdd7513592f6a6dd7482b7db0f65ed4f3a8f16ef02cf95c1aa2b9b64 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
4
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.10.101) ==:192.168.10.101
Input server IP (192.168.10.100) ==:192.168.10.100
Input Linux Kernel filename (firmware.bin) ==:firmware.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.10.100; our IP address is 192.168.10.101
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Loading: *Got ARP REPLY, set server/gtwy eth addr (00:e0:4c:68:80:7e)
Got it
#################################################################
--- snip ---
#################################################################
##
done
Bytes transferred = 3670776 (3802f8 hex)
LoadAddr=82000000 NetBootFileXferSize= 003802f8
raspi_erase_write: offs:50000, count:3802f8
raspi_erase: offs:50000 len:380000
........................................................
raspi_write: to:50000 len:380000
........................................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
--- snip ---
raspi_erase: offs:3d0000 len:10000
.
raspi_write: to:3d0000 len:10000
.
raspi_read: from:3d0000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1593597 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1850fd
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620a + MT7610e evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=000517e2
[ 0.000000] Readback ErrCtl register=000517e2
[ 0.000000] Memory: 58684K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 1196K init, 208K bss, 6852K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087720] pid_max: default: 32768 minimum: 301
[ 0.097125] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110152] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130179] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149666] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161839] pinctrl core: initialized pinctrl subsystem
[ 0.172684] NET: Registered protocol family 16
[ 0.442935] PCI host bridge /pcie@10140000 ranges:
[ 0.452340] MEM 0x0000000020000000..0x000000002fffffff
[ 0.462711] IO 0x0000000010160000..0x000000001016ffff
[ 0.490205] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.501246] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.514321] PCI host bridge to bus 0000:00
[ 0.522322] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.536039] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.547774] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.561273] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.577499] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.594060] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.607117] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.620935] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.634436] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.648800] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.662310] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.676859] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.691203] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.701049] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.714567] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.732622] clocksource: Switched to clocksource systick
[ 0.744304] NET: Registered protocol family 2
[ 0.753747] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.767530] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.780122] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.792910] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.804431] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.817130] NET: Registered protocol family 1
[ 0.828450] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.841188] Crashlog allocated RAM at address 0x3f00000
[ 0.853257] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.871827] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.883330] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.912914] io scheduler noop registered
[ 0.920559] io scheduler deadline registered (default)
[ 0.931659] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.945309] console [ttyS0] disabled
[ 0.952305] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.972081] console [ttyS0] enabled
[ 0.972081] console [ttyS0] enabled
[ 0.985862] bootconsole [early0] disabled
[ 0.985862] bootconsole [early0] disabled
[ 1.006988] spi spi0.0: force spi mode3
[ 1.017269] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 1.026575] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.039249] Creating 4 MTD partitions on "spi0.0":
[ 1.048817] 0x000000000000-0x000000030000 : "u-boot"
[ 1.059672] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.071200] 0x000000040000-0x000000050000 : "factory"
[ 1.082180] 0x000000050000-0x000000800000 : "firmware"
[ 1.096276] 2 uimage-fw partitions found on MTD device firmware
[ 1.108142] Creating 2 MTD partitions on "firmware":
[ 1.118060] 0x000000000000-0x00000018513d : "kernel"
[ 1.128862] 0x00000018513d-0x0000007b0000 : "rootfs"
[ 1.139630] mtd: device 5 (rootfs) set to be root filesystem
[ 1.152522] 1 squashfs-split partitions found on MTD device rootfs
[ 1.164914] 0x000000366000-0x0000007b0000 : "rootfs_data"
[ 1.177402] libphy: Fixed MDIO Bus: probed
[ 1.194403] gsw: setting port4 to gmac mode
[ 1.202814] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
[ 1.221056] mtk_soc_eth 10100000.ethernet: generated random MAC address 4e:8d:27:b8:66:59
[ 1.237550] libphy: mdio: probed
[ 1.244932] mdio_bus mdio-bus: MDIO device at address 5 is missing.
[ 1.257776] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=001cc916, driver=Generic PHY]
[ 1.278888] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.291370] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.308402] rt2880_wdt 10000120.watchdog: Initialized
[ 1.319822] NET: Registered protocol family 10
[ 1.333030] Segment Routing with IPv6
[ 1.340444] NET: Registered protocol family 17
[ 1.349413] 8021q: 802.1Q VLAN Support v1.8
[ 1.372785] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.393388] Freeing unused kernel memory: 1196K
[ 1.402407] This architecture does not have kernel memory protection.
[ 2.752567] random: fast init done
[ 3.107512] init: Console is alive
[ 3.114629] init: - watchdog -
[ 4.604563] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.873076] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.889771] init: - preinit -
[ 6.280385] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.292094] 8021q: adding VLAN 0 to HW filter on device eth0
[ 6.303922] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.478961] CPU 0 Unable to handle kernel paging request at virtual address 0000017c, epc == 8024f9a4, ra == 8023c358
[ 6.500112] Oops[#1]:
[ 6.504633] CPU: 0 PID: 123 Comm: kworker/0:1 Not tainted 4.14.180 #0
[ 6.517480] Workqueue: events_power_efficient phy_state_machine
[ 6.529267] task: 8398ad00 task.stack: 8396a000
[ 6.538279] $ 0 : 00000000 00000001 8049c584 00000000
[ 6.548690] $ 4 : 00000024 8049c570 00000000 00000000
[ 6.559098] $ 8 : 8396bfe0 0000a400 00000000 005fc155
[ 6.569505] $12 : 00000000 aa40bf19 00000000 00000000
[ 6.579913] $16 : 00000005 8381bd48 8381b800 00000064
[ 6.590321] $20 : 000003e8 00000001 0000000a 8381bc60
[ 6.600728] $24 : 8047d040 8024f938
[ 6.611136] $28 : 8396a000 8396be10 80480000 8023c358
[ 6.621548] Hi : 005fc155
[ 6.627271] Lo : 5c9a3293
[ 6.633026] epc : 8024f9a4 fe_phy_link_adjust+0x6c/0x198
[ 6.643949] ra : 8023c358 phy_state_machine+0x3f8/0x5c0
[ 6.654864] Status: 1100a402 KERNEL EXL
[ 6.662674] Cause : 00800008 (ExcCode 02)
[ 6.670648] BadVA : 0000017c
[ 6.676372] PrId : 00019650 (MIPS 24KEc)
[ 6.684342] Modules linked in: leds_gpio gpio_button_hotplug
[ 6.695621] Process kworker/0:1 (pid: 123, threadinfo=8396a000, task=8398ad00, tls=00000000)
[ 6.712420] Stack : 00000000 00000000 00000000 8023e4bc 00000000 839c79b4 839c7800 839c79e8
[ 6.729069] 8108d500 00000000 00000000 80490000 fffffffe 8023c358 5966b8ff 36f2f11a
[ 6.745718] 00000000 83b5fc40 839c79b4 839d5b80 00000000 8108d500 00000000 8003bcd4
[ 6.762366] 80485314 80485198 80490000 80485314 80490000 fffffffe 839d5b80 80485184
[ 6.779018] 839d5b98 80485198 80490000 80485314 80490000 8003c1a0 805d0000 804957c0
[ 6.795666] ...
[ 6.800528] Call Trace:
[ 6.805392] [<8024f9a4>] fe_phy_link_adjust+0x6c/0x198
[ 6.815627] [<8023c358>] phy_state_machine+0x3f8/0x5c0
[ 6.825873] [<8003bcd4>] process_one_work+0x26c/0x418
[ 6.835930] [<8003c1a0>] worker_thread+0x320/0x56c
[ 6.845473] [<80041574>] kthread+0x128/0x13c
[ 6.853979] [<80005a98>] ret_from_kernel_thread+0x14/0x1c
[ 6.864729] Code: 10600028 00000000 8c430000 <8c65017c> 10a00009 8c64016c 8c470060 8c660170 14e60007
[ 6.884161]
[ 6.887181] ---[ end trace 327cadda0aaf51ab ]---
[ 6.898060] Kernel panic - not syncing: Fatal exception
[ 6.909472] Rebooting in 1 seconds..
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:FFFF ID1:1C!!
\00\00
result: boots, with bad ethernet
file: http://82.165.248.139/virgin_mt7620_flavors/openwrt-ramips-mt7620-mt7620a_mt7530-squashfs-sysupgrade.bin
sha256sum firmware.bin
7874f60bbd3caa995a75a1b668c5a9d66b782bdd4b9c71a57592a4b5391deb90 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.10.101) ==:192.168.10.101
Input server IP (192.168.10.100) ==:192.168.10.100
Input Linux Kernel filename (firmware.bin) ==:firmware.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.10.100; our IP address is 192.168.10.101
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x82000000
Loading: *Got ARP REPLY, set server/gtwy eth addr (00:e0:4c:68:80:7e)
Got it
#################################################################
--- snip ---
#################################################################
##
done
Bytes transferred = 3670790 (380306 hex)
LoadAddr=82000000 NetBootFileXferSize= 00380306
raspi_erase_write: offs:50000, count:380306
raspi_erase: offs:50000 len:380000
........................................................
raspi_write: to:50000 len:380000
........................................................
raspi_read: from:50000 len:10000
--- snip ---
raspi_erase: offs:3d0000 len:10000
.
raspi_write: to:3d0000 len:10000
.
raspi_read: from:3d0000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1593547 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1850cb
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Ralink MT7620a + MT7530 evaluation board
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=000557c2
[ 0.000000] Readback ErrCtl register=000557c2
[ 0.000000] Memory: 58688K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 1196K init, 208K bss, 6848K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015469] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087716] pid_max: default: 32768 minimum: 301
[ 0.097123] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110150] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130149] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149633] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161807] pinctrl core: initialized pinctrl subsystem
[ 0.172654] NET: Registered protocol family 16
[ 0.442639] PCI host bridge /pcie@10140000 ranges:
[ 0.452029] MEM 0x0000000020000000..0x000000002fffffff
[ 0.462417] IO 0x0000000010160000..0x000000001016ffff
[ 0.489585] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.500625] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.513706] PCI host bridge to bus 0000:00
[ 0.521706] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.535425] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.547158] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.560657] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.576864] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.593418] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.606476] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.620293] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.633794] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.648158] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.661670] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.676217] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.690562] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.700407] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.713925] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.731980] clocksource: Switched to clocksource systick
[ 0.743654] NET: Registered protocol family 2
[ 0.753086] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.766865] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.779460] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.792257] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.803781] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.816458] NET: Registered protocol family 1
[ 0.827784] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.840511] Crashlog allocated RAM at address 0x3f00000
[ 0.852610] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.871186] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.882692] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.912265] io scheduler noop registered
[ 0.919909] io scheduler deadline registered (default)
[ 0.931016] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.944649] console [ttyS0] disabled
[ 0.951645] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.971421] console [ttyS0] enabled
[ 0.971421] console [ttyS0] enabled
[ 0.985202] bootconsole [early0] disabled
[ 0.985202] bootconsole [early0] disabled
[ 1.006267] spi spi0.0: force spi mode3
[ 1.016560] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 1.025864] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.038540] Creating 4 MTD partitions on "spi0.0":
[ 1.048108] 0x000000000000-0x000000030000 : "u-boot"
[ 1.058970] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.070475] 0x000000040000-0x000000050000 : "factory"
[ 1.081455] 0x000000050000-0x000000800000 : "firmware"
[ 1.095569] 2 uimage-fw partitions found on MTD device firmware
[ 1.107436] Creating 2 MTD partitions on "firmware":
[ 1.117353] 0x000000000000-0x00000018510b : "kernel"
[ 1.128157] 0x00000018510b-0x0000007b0000 : "rootfs"
[ 1.138929] mtd: device 5 (rootfs) set to be root filesystem
[ 1.151808] 1 squashfs-split partitions found on MTD device rootfs
[ 1.164203] 0x000000366000-0x0000007b0000 : "rootfs_data"
[ 1.176706] libphy: Fixed MDIO Bus: probed
[ 1.193255] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
[ 1.211529] mtk_soc_eth 10100000.ethernet: generated random MAC address fe:8a:39:eb:f0:31
[ 1.228023] libphy: mdio: probed
[ 1.235382] mdio_bus mdio-bus: MDIO device at address 1 is missing.
[ 1.248014] mdio_bus mdio-bus: MDIO device at address 2 is missing.
[ 1.260593] mdio_bus mdio-bus: MDIO device at address 3 is missing.
[ 1.273975] mdio_bus mdio-bus: MDIO device at address 31 is missing.
[ 1.286748] mtk_soc_eth 10100000.ethernet: using fixed link parameters
[ 1.300620] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.313120] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.330157] rt2880_wdt 10000120.watchdog: Initialized
[ 1.341566] NET: Registered protocol family 10
[ 1.354897] Segment Routing with IPv6
[ 1.362389] NET: Registered protocol family 17
[ 1.371304] 8021q: 802.1Q VLAN Support v1.8
[ 1.394671] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.415300] Freeing unused kernel memory: 1196K
[ 1.424353] This architecture does not have kernel memory protection.
[ 2.741927] random: fast init done
[ 3.129976] init: Console is alive
[ 3.137095] init: - watchdog -
[ 4.626572] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.894177] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.910647] init: - preinit -
[ 6.286527] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 6.302779] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.314446] 8021q: adding VLAN 0 to HW filter on device eth0
[ 6.326014] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.934395] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 6.975883] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 7.088569] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 7.112453] procd: - early -
[ 7.118310] procd: - watchdog -
[ 7.312017] procd: - watchdog -
[ 7.318647] procd: - ubus -
[ 7.396703] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.410205] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.423516] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.437300] procd: - init -
Please press Enter to activate this console.
[ 8.230872] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.280336] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.317209] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 8.332543] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 8.384563] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.419017] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 8.558445] xt_time: kernel timezone is -0000
[ 8.757710] PPP generic driver version 2.4.2
[ 8.782943] NET: Registered protocol family 24
[ 8.846961] urngd: jent-rng init failed, err: 2
[ 8.863598] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 8.883576] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 8.901806] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 9.134222] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[ 9.148892] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 9.165808] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 9.204392] kmodloader: done loading kernel modules from /etc/modules.d/*
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 19.07.3, r11063-85e04e9f46
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
------------[ cut here ]------------
[ 104.613418] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
[ 104.629903] NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
[ 104.643781] Modules linked in: rt2800soc rt2800pci rt2800mmio rt2800lib pppoe ppp_async rt2x00soc rt2x00pci rt2x00mmio rt2x00lib pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 eeprom_93cx6 leds_gpio gpio_button_hotplug
[ 104.777678] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.180 #0
[ 104.789478] Stack : 804a0000 8045573c 00000000 00000000 8042ef58 83807e34 8047fd2c 8047f947
[ 104.806150] 8042af98 00000000 805d3660 00000140 80493e74 00000001 83807de8 53261655
[ 104.822822] 00000000 00000000 805d0000 000040e0 00000000 000000c8 00000007 00000000
[ 104.839491] 00000000 80480000 000bddce 00000000 00000000 00000009 00000000 8044f9c4
[ 104.856162] 802a7250 00000140 80493e74 80493e34 00000002 80201494 00000000 805d0000
[ 104.872834] ...
[ 104.877714] Call Trace:
[ 104.882604] [<8000af90>] show_stack+0x58/0x100
[ 104.891472] [<80026990>] __warn+0xe4/0x13c
[ 104.899648] [<80026a18>] warn_slowpath_fmt+0x30/0x3c
[ 104.909557] [<802a7250>] dev_watchdog+0x164/0x274
[ 104.918946] [<800603d0>] call_timer_fn.isra.26+0x24/0x84
[ 104.929546] [<800605a4>] run_timer_softirq+0x174/0x1ec
[ 104.939813] [<8039d108>] __do_softirq+0xe8/0x2bc
[ 104.949031] [<80005f90>] except_vec_vi_end+0xb8/0xc4
[ 104.958939] [<8000790c>] r4k_wait_irqoff+0x18/0x24
[ 104.968499] ---[ end trace 2eb802ff6f44741e ]---
[ 104.977716] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[ 104.990046] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:80000067
[ 105.002038] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=03050000, max=1024, ctx=99, dtx=97, fdx=97, next=99
[ 105.022858] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=030b4000, max=1024, calc=1023, drx=0
[ 105.043549] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 105.097887] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 104.604186] ------------[ cut here ]------------
[ 104.613418] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
[ 104.629903] NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
[ 104.643781] Modules linked in: rt2800soc rt2800pci rt2800mmio rt2800lib pppoe ppp_async rt2x00soc rt2x00pci rt2x00mmio rt2x00lib pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 eeprom_93cx6 leds_gpio gpio_button_hotplug
[ 104.777678] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.180 #0
[ 104.789478] Stack : 804a0000 8045573c 00000000 00000000 8042ef58 83807e34 8047fd2c 8047f947
[ 104.806150] 8042af98 00000000 805d3660 00000140 80493e74 00000001 83807de8 53261655
[ 104.822822] 00000000 00000000 805d0000 000040e0 00000000 000000c8 00000007 00000000
[ 104.839491] 00000000 80480000 000bddce 00000000 00000000 00000009 00000000 8044f9c4
[ 104.856162] 802a7250 00000140 80493e74 80493e34 00000002 80201494 00000000 805d0000
[ 104.872834] ...
[ 104.877714] Call Trace:
[ 104.882604] [<8000af90>] show_stack+0x58/0x100
[ 104.891472] [<80026990>] __warn+0xe4/0x13c
[ 104.899648] [<80026a18>] warn_slowpath_fmt+0x30/0x3c
[ 104.909557] [<802a7250>] dev_watchdog+0x164/0x274
[ 104.918946] [<800603d0>] call_timer_fn.isra.26+0x24/0x84
[ 104.929546] [<800605a4>] run_timer_softirq+0x174/0x1ec
[ 104.939813] [<8039d108>] __do_softirq+0xe8/0x2bc
[ 104.949031] [<80005f90>] except_vec_vi_end+0xb8/0xc4
[ 104.958939] [<8000790c>] r4k_wait_irqoff+0x18/0x24
[ 104.968499] ---[ end trace 2eb802ff6f44741e ]---
[ 104.977716] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[ 104.990046] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:80000067
[ 105.002038] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=03050000, max=1024, ctx=99, dtx=97, fdx=97, next=99
[ 105.022858] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=030b4000, max=1024, calc=1023, drx=0
[ 105.043549] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 105.097887] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
[ 127.626506] mtk_soc_eth 10100000.ethernet eth0: transmit timed out
[ 127.638855] mtk_soc_eth 10100000.ethernet eth0: dma_cfg:80000067
[ 127.650855] mtk_soc_eth 10100000.ethernet eth0: tx_ring=0, base=03050000, max=1024, ctx=76, dtx=0, fdx=0, next=76
[ 127.671334] mtk_soc_eth 10100000.ethernet eth0: rx_ring=0, base=03058000, max=1024, calc=1023, drx=0
[ 127.690073] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
[ 127.743971] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
1 Like
but it boots 
I have company here. a friend and a client coming to pick console radio. 24 hour business.
It's not a gig port. I'll look later our you can.
[ 6.286527] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
result: boots, ethernet working, wifi 2.4 working, wifi 5 not working (<= no radio1)
file: http://82.165.248.139/edit-asus-booting-more-wifi-network/openwrt-ramips-mt7620-rp-n53-squashfs-sysupgrade.bin
sha256sum firmware.bin
b94da96643583469b4aa0822908ee069b79e82803bb4fbdfc927135ea4940d73 firmware.bin
U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fa0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c8 40 17 c8 40 (4017c840)
find flash: GD25Q64B
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 13 2018 Time:15:43:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Read PhyID ID0:FFFF ID1:1C!!
Read PhyID ID0:1C ID1:1C!!
RLT Phy2
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
4 3 2 1 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.180
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1593701 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:185165
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@ap-builder) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 Sat May 16 18:32:20 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Asus RP-N53
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 58684K/65536K available (3704K kernel code, 179K rwdata, 864K rodata, 1196K init, 208K bss, 6852K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015469] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087723] pid_max: default: 32768 minimum: 301
[ 0.097128] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110155] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130397] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149879] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.162054] pinctrl core: initialized pinctrl subsystem
[ 0.172899] NET: Registered protocol family 16
[ 0.443627] PCI host bridge /pcie@10140000 ranges:
[ 0.453032] MEM 0x0000000020000000..0x000000002fffffff
[ 0.463403] IO 0x0000000010160000..0x000000001016ffff
[ 0.491484] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.502526] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.515130] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.526139] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.539201] PCI host bridge to bus 0000:00
[ 0.547200] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.560918] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.572652] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.586152] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.602378] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.618950] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.632006] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.645825] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.659326] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.673691] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.687201] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.701749] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.716093] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.725938] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.739457] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.757993] clocksource: Switched to clocksource systick
[ 0.769681] NET: Registered protocol family 2
[ 0.779111] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.792894] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.805485] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.818270] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.829792] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.842489] NET: Registered protocol family 1
[ 0.853827] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.866578] Crashlog allocated RAM at address 0x3f00000
[ 0.878664] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.897229] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.908735] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.938325] io scheduler noop registered
[ 0.945969] io scheduler deadline registered (default)
[ 0.957118] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.970787] console [ttyS0] disabled
[ 0.977784] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.997559] console [ttyS0] enabled
[ 0.997559] console [ttyS0] enabled
[ 1.011341] bootconsole [early0] disabled
[ 1.011341] bootconsole [early0] disabled
[ 1.032506] spi spi0.0: force spi mode3
[ 1.042800] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 1.052107] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.064781] Creating 4 MTD partitions on "spi0.0":
[ 1.074348] 0x000000000000-0x000000030000 : "u-boot"
[ 1.085184] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.096699] 0x000000040000-0x000000050000 : "factory"
[ 1.107713] 0x000000050000-0x000000800000 : "firmware"
[ 1.121753] 2 uimage-fw partitions found on MTD device firmware
[ 1.133620] Creating 2 MTD partitions on "firmware":
[ 1.143537] 0x000000000000-0x0000001851a5 : "kernel"
[ 1.154345] 0x0000001851a5-0x0000007b0000 : "rootfs"
[ 1.165125] mtd: device 5 (rootfs) set to be root filesystem
[ 1.178056] 1 squashfs-split partitions found on MTD device rootfs
[ 1.190413] 0x000000367000-0x0000007b0000 : "rootfs_data"
[ 1.202895] libphy: Fixed MDIO Bus: probed
[ 1.219916] gsw: setting port4 to ephy mode
[ 1.228326] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex)
[ 1.246565] mtk_soc_eth 10100000.ethernet: generated random MAC address ba:1a:b7:67:0e:60
[ 1.262960] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.275475] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.292497] rt2880_wdt 10000120.watchdog: Initialized
[ 1.303905] NET: Registered protocol family 10
[ 1.316749] Segment Routing with IPv6
[ 1.324230] NET: Registered protocol family 17
[ 1.333161] 8021q: 802.1Q VLAN Support v1.8
[ 1.354487] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.375099] Freeing unused kernel memory: 1196K
[ 1.384164] This architecture does not have kernel memory protection.
[ 2.747933] random: fast init done
[ 3.089506] init: Console is alive
[ 3.096521] init: - watchdog -
[ 4.585978] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.856648] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.873001] init: - preinit -
[ 6.251459] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
4
[ 6.658640] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 6.700223] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.825151] procd: Change state 0 -> 1
[ 6.832813] procd: - early -
[ 6.838628] procd: Watchdog handover: fd=3
[ 6.846931] procd: - watchdog -
[ 6.853432] procd: Ping
[ 6.858426] procd: Opened watchdog with timeout 30s
[ 7.004124] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/mem/full","SUBSYSTEM":"mem","SYNTH_UUID":"0","MAJOR":"1","MINOR":"7","DEVNAME":"full","DEVMODE":"0666","SEQNUM":"315"}}
[ 7.037331] procd: Command: makedev
[ 7.044445] procd: /dev/full
[ 7.050494] procd: 0666
[ 7.055606] procd: Message:
[ 7.061387] procd: ACTION=add
[ 7.067544] procd: DEVPATH=/devices/virtual/mem/full
[ 7.077752] procd: SUBSYSTEM=mem
[ 7.084497] procd: SYNTH_UUID=0
[ 7.091137] procd: MAJOR=1
[ 7.096774] procd: MINOR=7
[ 7.102480] procd: DEVNAME=full
[ 7.108979] procd: DEVMODE=0666
[ 7.115545] procd: SEQNUM=315
[ 7.122143] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/mem/urandom","SUBSYSTEM":"mem","SYNTH_UUID":"0","MAJOR":"1","MINOR":"9","DEVNAME":"urandom","DEVMODE":"0666","SEQNUM":"316"}}
[ 7.156127] procd: Command: makedev
[ 7.163234] procd: /dev/urandom
[ 7.169801] procd: 0666
[ 7.174912] procd: Message:
[ 7.180690] procd: ACTION=add
[ 7.186848] procd: DEVPATH=/devices/virtual/mem/urandom
[ 7.197580] procd: SUBSYSTEM=mem
[ 7.204324] procd: SYNTH_UUID=0
[ 7.210965] procd: MAJOR=1
[ 7.216602] procd: MINOR=9
[ 7.222309] procd: DEVNAME=urandom
[ 7.229397] procd: DEVMODE=0666
[ 7.235897] procd: SEQNUM=316
[ 7.242486] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/mem/null","SUBSYSTEM":"mem","SYNTH_UUID":"0","MAJOR":"1","MINOR":"3","DEVNAME":"null","DEVMODE":"0666","SEQNUM":"317"}}
[ 7.275430] procd: Command: makedev
[ 7.282537] procd: /dev/null
[ 7.288517] procd: 0666
[ 7.293693] procd: Message:
[ 7.299475] procd: ACTION=add
[ 7.305632] procd: DEVPATH=/devices/virtual/mem/null
[ 7.315840] procd: SUBSYSTEM=mem
[ 7.322584] procd: SYNTH_UUID=0
[ 7.329085] procd: MAJOR=1
[ 7.334857] procd: MINOR=3
[ 7.340570] procd: DEVNAME=null
[ 7.347069] procd: DEVMODE=0666
[ 7.353635] procd: SEQNUM=317
[ 7.360224] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/mem/random","SUBSYSTEM":"mem","SYNTH_UUID":"0","MAJOR":"1","MINOR":"8","DEVNAME":"random","DEVMODE":"0666","SEQNUM":"318"}}
[ 7.395019] procd: Command: makedev
[ 7.410755] procd: /dev/random
[ 7.417099] procd: 0666
[ 7.422391] procd: Message:
[ 7.428032] procd: ACTION=add
[ 7.434262] procd: DEVPATH=/devices/virtual/mem/random
[ 7.444813] procd: SUBSYSTEM=mem
[ 7.451628] procd: SYNTH_UUID=0
[ 7.458132] procd: MAJOR=1
[ 7.463841] procd: MINOR=8
[ 7.469546] procd: DEVNAME=random
[ 7.476391] procd: DEVMODE=0666
[ 7.483031] procd: SEQNUM=318
[ 7.489648] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/misc/network_latency","SUBSYSTEM":"misc","SYNTH_UUID":"0","MAJOR":"10","MINOR":"62","DEVNAME":"network_latency","SEQNUM":"319"}}
[ 7.524371] procd: Command: makedev
[ 7.531494] procd: /dev/network_latency
[ 7.539457] procd: 0600
[ 7.544567] procd: Message:
[ 7.550350] procd: ACTION=add
[ 7.556508] procd: DEVPATH=/devices/virtual/misc/network_latency
[ 7.568793] procd: SUBSYSTEM=misc
[ 7.575710] procd: SYNTH_UUID=0
[ 7.582349] procd: MAJOR=10
[ 7.588159] procd: MINOR=62
[ 7.594041] procd: DEVNAME=network_latency
[ 7.602515] procd: SEQNUM=319
[ 7.609171] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/misc/memory_bandwidth","SUBSYSTEM":"misc","SYNTH_UUID":"0","MAJOR":"10","MINOR":"60","DEVNAME":"memory_bandwidth","SEQNUM":"320"}}
[ 7.644234] procd: Command: makedev
[ 7.651355] procd: /dev/memory_bandwidth
[ 7.659482] procd: 0600
[ 7.664593] procd: Message:
[ 7.670377] procd: ACTION=add
[ 7.676536] procd: DEVPATH=/devices/virtual/misc/memory_bandwidth
[ 7.688994] procd: SUBSYSTEM=misc
[ 7.695910] procd: SYNTH_UUID=0
[ 7.702549] procd: MAJOR=10
[ 7.708359] procd: MINOR=60
[ 7.714240] procd: DEVNAME=memory_bandwidth
[ 7.722889] procd: SEQNUM=320
[ 7.729603] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/misc/cpu_dma_latency","SUBSYSTEM":"misc","SYNTH_UUID":"0","MAJOR":"10","MINOR":"63","DEVNAME":"cpu_dma_latency","SEQNUM":"321"}}
[ 7.764274] procd: Command: makedev
[ 7.771394] procd: /dev/cpu_dma_latency
[ 7.779331] procd: 0600
[ 7.784458] procd: Message:
[ 7.790239] procd: ACTION=add
[ 7.796398] procd: DEVPATH=/devices/virtual/misc/cpu_dma_latency
[ 7.808683] procd: SUBSYSTEM=misc
[ 7.815599] procd: SYNTH_UUID=0
[ 7.822240] procd: MAJOR=10
[ 7.828049] procd: MINOR=63
[ 7.833931] procd: DEVNAME=cpu_dma_latency
[ 7.842406] procd: SEQNUM=321
[ 7.848970] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000120.watchdog/misc/watchdog","SUBSYSTEM":"misc","SYNTH_UUID":"0","MAJOR":"10","MINOR":"130","DEVNAME":"watchdog","SEQNUM":"322"}}
[ 7.887657] procd: Command: makedev
[ 7.894788] procd: /dev/watchdog
[ 7.901529] procd: 0600
[ 7.906641] procd: Message:
[ 7.912423] procd: ACTION=add
[ 7.918583] procd: DEVPATH=/devices/platform/10000000.palmbus/10000120.watchdog/misc/watchdog
[ 7.935890] procd: SUBSYSTEM=misc
[ 7.942878] procd: SYNTH_UUID=0
[ 7.949458] procd: MAJOR=10
[ 7.955265] procd: MINOR=130
[ 7.961312] procd: DEVNAME=watchdog
[ 7.968506] procd: SEQNUM=322
[ 7.975209] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/misc/network_throughput","SUBSYSTEM":"misc","SYNTH_UUID":"0","MAJOR":"10","MINOR":"61","DEVNAME":"network_throughput","SEQNUM":"323"}}
[ 8.010963] procd: Command: makedev
[ 8.017999] procd: /dev/network_throughput
[ 8.026486] procd: 0600
[ 8.031667] procd: Message:
[ 8.037303] procd: ACTION=add
[ 8.043607] procd: DEVPATH=/devices/virtual/misc/network_throughput
[ 8.056419] procd: SUBSYSTEM=misc
[ 8.063335] procd: SYNTH_UUID=0
[ 8.069974] procd: MAJOR=10
[ 8.075784] procd: MINOR=61
[ 8.081666] procd: DEVNAME=network_throughput
[ 8.090661] procd: SEQNUM=323
[ 8.097257] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000120.watchdog/watchdog/watchdog0","SUBSYSTEM":"watchdog","SYNTH_UUID":"0","MAJOR":"253","MINOR":"0","DEVNAME":"watchdog0","SEQNUM":"324"}}
[ 8.137502] procd: Command: makedev
[ 8.144623] procd: /dev/watchdog0
[ 8.151539] procd: 0600
[ 8.156651] procd: Message:
[ 8.162433] procd: ACTION=add
[ 8.168594] procd: DEVPATH=/devices/platform/10000000.palmbus/10000120.watchdog/watchdog/watchdog0
[ 8.186768] procd: SUBSYSTEM=watchdog
[ 8.194452] procd: SYNTH_UUID=0
[ 8.201032] procd: MAJOR=253
[ 8.207013] procd: MINOR=0
[ 8.212713] procd: DEVNAME=watchdog0
[ 8.220220] procd: SEQNUM=324
[ 8.226852] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/tty/ptmx","SUBSYSTEM":"tty","SYNTH_UUID":"0","MAJOR":"5","MINOR":"2","DEVNAME":"ptmx","DEVMODE":"0666","SEQNUM":"325"}}
[ 8.259803] procd: Command: makedev
[ 8.266829] procd: /dev/ptmx
[ 8.272887] procd: 0666
[ 8.277999] procd: Message:
[ 8.283701] procd: ACTION=add
[ 8.290005] procd: DEVPATH=/devices/virtual/tty/ptmx
[ 8.300220] procd: SUBSYSTEM=tty
[ 8.306894] procd: SYNTH_UUID=0
[ 8.313459] procd: MAJOR=5
[ 8.319092] procd: MINOR=2
[ 8.324864] procd: DEVNAME=ptmx
[ 8.331442] procd: DEVMODE=0666
[ 8.337942] procd: SEQNUM=325
[ 8.344458] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/tty/console","SUBSYSTEM":"tty","SYNTH_UUID":"0","MAJOR":"5","MINOR":"1","DEVNAME":"console","SEQNUM":"326"}}
[ 8.375698] procd: Command: makedev
[ 8.382829] procd: /dev/console
[ 8.389400] procd: 0600
[ 8.394534] procd: Message:
[ 8.400320] procd: ACTION=add
[ 8.406478] procd: DEVPATH=/devices/virtual/tty/console
[ 8.417205] procd: SUBSYSTEM=tty
[ 8.423950] procd: SYNTH_UUID=0
[ 8.430589] procd: MAJOR=5
[ 8.436226] procd: MINOR=1
[ 8.441934] procd: DEVNAME=console
[ 8.448953] procd: SEQNUM=326
[ 8.455635] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000c00.uartlite/tty/ttyS0","SUBSYSTEM":"tty","SYNTH_UUID":"0","MAJOR":"4","MINOR":"64","DEVNAME":"ttyS0","SEQNUM":"327"}}
[ 8.492592] procd: Command: makedev
[ 8.499713] procd: /dev/ttyS0
[ 8.505866] procd: 0660
[ 8.511045] procd: dialout
[ 8.516674] procd: Message:
[ 8.522459] procd: ACTION=add
[ 8.528619] procd: DEVPATH=/devices/platform/10000000.palmbus/10000c00.uartlite/tty/ttyS0
[ 8.545233] procd: SUBSYSTEM=tty
[ 8.552048] procd: SYNTH_UUID=0
[ 8.558551] procd: MAJOR=4
[ 8.564259] procd: MINOR=64
[ 8.570136] procd: DEVNAME=ttyS0
[ 8.576810] procd: SEQNUM=327
[ 8.583583] procd: Command: makedev
[ 8.590720] procd: /dev/ttyS0
[ 8.596872] procd: 0600
[ 8.602050] procd: Message:
[ 8.607686] procd: ACTION=add
[ 8.614001] procd: DEVPATH=/devices/platform/10000000.palmbus/10000c00.uartlite/tty/ttyS0
[ 8.630622] procd: SUBSYSTEM=tty
[ 8.637296] procd: SYNTH_UUID=0
[ 8.643932] procd: MAJOR=4
[ 8.649645] procd: MINOR=64
[ 8.655452] procd: DEVNAME=ttyS0
[ 8.662191] procd: SEQNUM=327
[ 8.668727] procd: {{"ACTION":"add","DEVPATH":"/devices/virtual/tty/tty","SUBSYSTEM":"tty","SYNTH_UUID":"0","MAJOR":"5","MINOR":"0","DEVNAME":"tty","DEVMODE":"0666","SEQNUM":"328"}}
[ 8.701315] procd: Command: makedev
[ 8.708342] procd: /dev/tty
[ 8.714227] procd: 0666
[ 8.719408] procd: Message:
[ 8.725044] procd: ACTION=add
[ 8.731342] procd: DEVPATH=/devices/virtual/tty/tty
[ 8.741384] procd: SUBSYSTEM=tty
[ 8.748058] procd: SYNTH_UUID=0
[ 8.754623] procd: MAJOR=5
[ 8.760397] procd: MINOR=0
[ 8.766034] procd: DEVNAME=tty
[ 8.772432] procd: DEVMODE=0666
[ 8.778932] procd: SEQNUM=328
[ 8.785448] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/serial8250/tty/ttyS1","SUBSYSTEM":"tty","SYNTH_UUID":"0","MAJOR":"4","MINOR":"65","DEVNAME":"ttyS1","SEQNUM":"329"}}
[ 8.818240] procd: Command: makedev
[ 8.825361] procd: /dev/ttyS1
[ 8.831584] procd: 0660
[ 8.836697] procd: dialout
[ 8.842474] procd: Message:
[ 8.848112] procd: ACTION=add
[ 8.854342] procd: DEVPATH=/devices/platform/serial8250/tty/ttyS1
[ 8.866797] procd: SUBSYSTEM=tty
[ 8.873612] procd: SYNTH_UUID=0
[ 8.880191] procd: MAJOR=4
[ 8.885824] procd: MINOR=65
[ 8.891697] procd: DEVNAME=ttyS1
[ 8.898393] procd: SEQNUM=329
[ 8.904993] procd: Command: makedev
[ 8.912121] procd: /dev/ttyS1
[ 8.918274] procd: 0600
[ 8.923451] procd: Message:
[ 8.929086] procd: ACTION=add
[ 8.935393] procd: DEVPATH=/devices/platform/serial8250/tty/ttyS1
[ 8.947858] procd: SUBSYSTEM=tty
[ 8.954601] procd: SYNTH_UUID=0
[ 8.961240] procd: MAJOR=4
[ 8.966877] procd: MINOR=65
[ 8.972757] procd: DEVNAME=ttyS1
[ 8.979501] procd: SEQNUM=329
[ 8.986050] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd4/mtdblock4","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"4","DEVNAME":"mtdblock4","DEVTYPE":"disk","SEQNUM":"330"}}
[ 9.032514] procd: Command: makedev
[ 9.039636] procd: /dev/mtdblock4
[ 9.046480] procd: 0600
[ 9.051658] procd: Message:
[ 9.057293] procd: ACTION=add
[ 9.063599] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd4/mtdblock4
[ 9.085759] procd: SUBSYSTEM=block
[ 9.092918] procd: SYNTH_UUID=0
[ 9.099496] procd: MAJOR=31
[ 9.105302] procd: MINOR=4
[ 9.111003] procd: DEVNAME=mtdblock4
[ 9.118369] procd: DEVTYPE=disk
[ 9.125008] procd: SEQNUM=330
[ 9.131726] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd2/mtdblock2","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"2","DEVNAME":"mtdblock2","DEVTYPE":"disk","SEQNUM":"331"}}
[ 9.177341] procd: Command: makedev
[ 9.184471] procd: /dev/mtdblock2
[ 9.191390] procd: 0600
[ 9.196501] procd: Message:
[ 9.202284] procd: ACTION=add
[ 9.208445] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd2/mtdblock2
[ 9.229803] procd: SUBSYSTEM=block
[ 9.236825] procd: SYNTH_UUID=0
[ 9.243398] procd: MAJOR=31
[ 9.249205] procd: MINOR=2
[ 9.254904] procd: DEVNAME=mtdblock2
[ 9.262412] procd: DEVTYPE=disk
[ 9.268916] procd: SEQNUM=331
[ 9.275567] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd0/mtdblock0","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"0","DEVNAME":"mtdblock0","DEVTYPE":"disk","SEQNUM":"332"}}
[ 9.321173] procd: Command: makedev
[ 9.328208] procd: /dev/mtdblock0
[ 9.335139] procd: 0600
[ 9.340322] procd: Message:
[ 9.345958] procd: ACTION=add
[ 9.352265] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd0/mtdblock0
[ 9.373559] procd: SUBSYSTEM=block
[ 9.380719] procd: SYNTH_UUID=0
[ 9.387222] procd: MAJOR=31
[ 9.393102] procd: MINOR=0
[ 9.398759] procd: DEVNAME=mtdblock0
[ 9.406191] procd: DEVTYPE=disk
[ 9.412835] procd: SEQNUM=332
[ 9.419502] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd5/mtdblock5","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"5","DEVNAME":"mtdblock5","DEVTYPE":"disk","SEQNUM":"333"}}
[ 9.465941] procd: Command: makedev
[ 9.473060] procd: /dev/mtdblock5
[ 9.479976] procd: 0600
[ 9.485088] procd: Message:
[ 9.490870] procd: ACTION=add
[ 9.497033] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd5/mtdblock5
[ 9.519189] procd: SUBSYSTEM=block
[ 9.526350] procd: SYNTH_UUID=0
[ 9.532929] procd: MAJOR=31
[ 9.538736] procd: MINOR=5
[ 9.544436] procd: DEVNAME=mtdblock5
[ 9.551942] procd: DEVTYPE=disk
[ 9.558446] procd: SEQNUM=333
[ 9.565093] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtdblock3","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"3","DEVNAME":"mtdblock3","DEVTYPE":"disk","SEQNUM":"334"}}
[ 9.610698] procd: Command: makedev
[ 9.617733] procd: /dev/mtdblock3
[ 9.624663] procd: 0600
[ 9.629845] procd: Message:
[ 9.635480] procd: ACTION=add
[ 9.641787] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtdblock3
[ 9.663082] procd: SUBSYSTEM=block
[ 9.670242] procd: SYNTH_UUID=0
[ 9.676745] procd: MAJOR=31
[ 9.682625] procd: MINOR=3
[ 9.688259] procd: DEVNAME=mtdblock3
[ 9.695690] procd: DEVTYPE=disk
[ 9.702332] procd: SEQNUM=334
[ 9.708946] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd1/mtdblock1","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"1","DEVNAME":"mtdblock1","DEVTYPE":"disk","SEQNUM":"335"}}
[ 9.754561] procd: Command: makedev
[ 9.761682] procd: /dev/mtdblock1
[ 9.768528] procd: 0600
[ 9.773706] procd: Message:
[ 9.779493] procd: ACTION=add
[ 9.785655] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd1/mtdblock1
[ 9.806945] procd: SUBSYSTEM=block
[ 9.814105] procd: SYNTH_UUID=0
[ 9.820684] procd: MAJOR=31
[ 9.826491] procd: MINOR=1
[ 9.832192] procd: DEVNAME=mtdblock1
[ 9.839698] procd: DEVTYPE=disk
[ 9.846202] procd: SEQNUM=335
[ 9.852850] procd: {{"ACTION":"add","DEVPATH":"/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd6/mtdblock6","SUBSYSTEM":"block","SYNTH_UUID":"0","MAJOR":"31","MINOR":"6","DEVNAME":"mtdblock6","DEVTYPE":"disk","SEQNUM":"336"}}
[ 9.899381] procd: Command: makedev
[ 9.906425] procd: /dev/mtdblock6
[ 9.913336] procd: 0600
[ 9.918448] procd: Message:
[ 9.924229] procd: ACTION=add
[ 9.930467] procd: DEVPATH=/devices/platform/10000000.palmbus/10000b00.spi/spi_master/spi0/spi0.0/mtd/mtd3/mtd6/mtdblock6
[ 9.952687] procd: SUBSYSTEM=block
[ 9.959787] procd: SYNTH_UUID=0
[ 9.966287] procd: MAJOR=31
[ 9.972159] procd: MINOR=6
[ 9.977793] procd: DEVNAME=mtdblock6
[ 9.985296] procd: DEVTYPE=disk
[ 9.991877] procd: SEQNUM=336
[ 10.049160] procd: Coldplug complete
[ 10.056447] procd: Change state 1 -> 2
[ 10.064057] procd: - watchdog -
[ 10.070534] procd: Ping
[ 10.075515] procd: Opened watchdog with timeout 30s
[ 10.085606] procd: - ubus -
[ 10.091409] procd: Create service ubus
[ 10.099018] procd: Start instance ubus::instance1
[ 10.109157] procd: Started instance ubus::instance1[412]
[ 10.131950] procd: running /etc/init.d/ubus running
[ 10.153162] procd: glob failed on /etc/init.d/ubus
[ 10.211534] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.225049] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.238365] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.252180] procd: Connected to ubus, id=0be4fe17
[ 10.261824] procd: Change state 2 -> 3
[ 10.269366] procd: - init -
[ 10.275820] procd: Parsing inittab - ::sysinit:/etc/init.d/rcS S boot
[ 10.289022] procd: Parsing inittab - ::shutdown:/etc/init.d/rcS K shutdown
[ 10.302965] procd: Parsing inittab - ::askconsole:/usr/libexec/login.sh
[ 10.317239] procd: Launched new askconsole action, pid=413
[ 10.378798] procd: running /etc/rc.d/S* boot
Please press Enter to activate this console.
[ 11.126286] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.168960] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.210046] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 11.225357] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 11.272530] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.308342] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 11.453847] xt_time: kernel timezone is -0000
[ 11.655554] PPP generic driver version 2.4.2
[ 11.680650] NET: Registered protocol family 24
[ 11.759713] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.774153] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.789634] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.815215] urngd: jent-rng init failed, err: 2
[ 11.919921] kmodloader: done loading kernel modules from /etc/modules.d/*
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 19.07.3, r11063-85e04e9f46
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# [ 35.129518] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 35.187418] jffs2_build_filesystem(): unlocking the mtd device...
[ 35.187492] done.
[ 35.203712] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 38.825914] 8021q: adding VLAN 0 to HW filter on device eth0
[ 38.954250] br-lan: port 1(eth0.1) entered blocking state
[ 38.965087] br-lan: port 1(eth0.1) entered disabled state
[ 38.976256] device eth0.1 entered promiscuous mode
[ 38.985855] device eth0 entered promiscuous mode
[ 39.109041] br-lan: port 1(eth0.1) entered blocking state
[ 39.119874] br-lan: port 1(eth0.1) entered forwarding state
[ 39.131227] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 39.883202] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
udhcpc: started, v1.30.1
udhcpc: sending discover
udhcpc: no lease, failing
root@OpenWrt:/# wifi config
root@OpenWrt:/# [ 86.078564] done.
[ 86.082441] jffs2: notice: (983) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 86.283306] overlayfs: upper fs does not support tmpfile.
root@OpenWrt:/# cat /etc/config/wireless
config wifi-device 'radio0'
option type 'mac80211'
option channel '11'
option hwmode '11g'
option path 'platform/10180000.wmac'
option htmode 'HT20'
option disabled '1'
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'OpenWrt'
option encryption 'none'
root@OpenWrt:/# [ 89.204606] random: crng init done
[ 89.211394] random: 7 urandom warning(s) missed due to ratelimiting
1 Like