My MT7621 board (WiTi) does not see the ASM1061 SATA controller which is soldered on the board.
Model MQmaker WiTi
Architecture MediaTek MT7621 ver:1 eco:3
Target Platform ramips/mt7621
Firmware Version OpenWrt 21.02.2 r16495-bf0c965af0 / LuCI openwrt-21.02 branch git-22.046.85957-59c3392
Kernel Version 5.4.179
root@OpenWrt:~# lspci -tv
-[0000:00]-+-00.0-[01]----00.0 MEDIATEK Corp. MT7662E 802.11ac PCI Express Wireless Network Adapter
\-01.0-[02]----00.0 MEDIATEK Corp. MT7662E 802.11ac PCI Express Wireless Network Adapter
[ 0.000000] Linux version 5.4.179 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16495-bf0c965af0)) #0 SMP Wed Feb 16 20:29:10 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is MQmaker WiTi
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 576 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00002040
[ 0.000000] Readback ErrCtl register=00002040
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 250792K/262144K available (6095K kernel code, 204K rwdata, 748K rodata, 1260K init, 238K bss, 11352K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x806e5a3c with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000011] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.015555] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.055882] pid_max: default: 32768 minimum: 301
[ 0.065272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.079683] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.098487] rcu: Hierarchical SRCU implementation.
[ 0.108789] smp: Bringing up secondary CPUs ...
[ 7.667000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 7.667015] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 7.667031] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 7.667162] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.146024] Synchronize counters for CPU 1: done.
[ 7.764613] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 7.764622] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 7.764630] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 7.764702] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.240661] Synchronize counters for CPU 2: done.
[ 7.849334] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 7.849341] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 7.849351] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 7.849424] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.328267] Synchronize counters for CPU 3: done.
[ 0.387891] smp: Brought up 1 node, 4 CPUs
[ 0.400838] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.420159] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.434072] pinctrl core: initialized pinctrl subsystem
[ 0.446683] NET: Registered protocol family 16
[ 0.464052] FPU Affinity set after 4688 emulations
[ 0.487528] clocksource: Switched to clocksource GIC
[ 0.499719] thermal_sys: Registered thermal governor 'step_wise'
[ 0.500342] NET: Registered protocol family 2
[ 0.521024] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.536437] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.553057] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.568203] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.582373] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.595127] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.608039] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.622199] NET: Registered protocol family 1
[ 0.630783] PCI: CLS 0 bytes, default 32
[ 0.727433] 4 CPUs re-calibrate udelay(lpj = 1167360)
[ 0.739634] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.755467] random: fast init done
[ 0.768792] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.780298] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.801948] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.818971] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.830366] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.841729] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.853812] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.870857] printk: console [ttyS0] disabled
[ 0.879349] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.897273] printk: console [ttyS0] enabled
[ 0.913798] printk: bootconsole [early0] disabled
[ 0.936239] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.950471] spi-nor spi0.0: gd25q128 (16384 Kbytes)
[ 0.960310] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.972968] Creating 4 MTD partitions on "spi0.0":
[ 0.982520] 0x000000000000-0x000000030000 : "u-boot"
[ 0.994188] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.006576] 0x000000040000-0x000000050000 : "factory"
[ 1.018314] 0x000000050000-0x000001000000 : "firmware"
[ 1.030623] 2 uimage-fw partitions found on MTD device firmware
[ 1.042457] Creating 2 MTD partitions on "firmware":
[ 1.052363] 0x000000000000-0x000000242750 : "kernel"
[ 1.064044] 0x000000242750-0x000000fb0000 : "rootfs"
[ 1.075820] mtd: device 5 (rootfs) set to be root filesystem
[ 1.087325] 1 squashfs-split partitions found on MTD device rootfs
[ 1.099694] 0x0000005b0000-0x000000fb0000 : "rootfs_data"
[ 1.142309] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.158333] mtk_soc_eth 1e100000.ethernet: generated random MAC address ba:12:4a:eb:59:f7
[ 1.175824] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22
[ 1.203478] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-6 addr=0e, data=03
[ 1.218406] rtc-pcf8563 0-0051: pcf8563_probe: write error
[ 1.229359] rtc-pcf8563: probe of 0-0051 failed with error -5
[ 1.240818] i2c-mt7621 1e000900.i2c: clock 100 kHz
[ 1.252229] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 1.265908] NET: Registered protocol family 10
[ 1.276600] Segment Routing with IPv6
[ 1.284059] NET: Registered protocol family 17
[ 1.293018] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.319153] 8021q: 802.1Q VLAN Support v1.8
[ 1.329844] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.356596] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 1.375001] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 1.393257] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 1.411748] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 1.430214] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 1.448398] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.466055] DSA: tree 0 setup
[ 1.472400] rt2880-pinmux pinctrl: pcie is already enabled
[ 1.483533] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 1.498502] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.613275] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.624390] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.735404] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.749274] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.758983] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.768702] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.787460] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.800136] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.813829] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.827525] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.838496] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.850499] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.862989] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[ 1.875555] pci 0000:00:00.0: supports D1
[ 1.883539] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.895468] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.907481] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.919970] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[ 1.932523] pci 0000:00:01.0: supports D1
[ 1.940506] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.953477] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.965515] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.979074] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.992533] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 2.006051] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.016477] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.028616] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.042136] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.056529] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.069958] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[ 2.081991] pci 0000:02:00.0: reg 0x10: [mem 0x60200000-0x602fffff 64bit]
[ 2.095565] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.109016] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.122545] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 2.132975] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 2.145111] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.158630] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 2.173020] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.186252] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.199458] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.213326] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.226498] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.240369] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.253890] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 2.268279] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 2.281801] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 2.296189] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 2.309713] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 2.323237] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 2.336763] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 2.350292] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.364864] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 2.379248] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.389136] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 2.402657] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.416179] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.430570] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[ 2.445142] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[ 2.459527] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.469410] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 2.482928] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.496450] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 2.511624] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 2.512082] hctosys: unable to open rtc device (rtc0)
[ 2.542366] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.563077] Freeing unused kernel memory: 1260K
[ 2.572147] This architecture does not have kernel memory protection.
[ 2.584970] Run /sbin/init as init process
[ 3.588939] init: Console is alive
[ 3.596074] init: - watchdog -
[ 5.166504] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.330265] usbcore: registered new interface driver usbfs
[ 5.341378] usbcore: registered new interface driver hub
[ 5.352133] usbcore: registered new device driver usb
[ 5.372933] SCSI subsystem initialized
[ 5.394527] libata version 3.00 loaded.
[ 5.407843] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 5.425180] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 5.442933] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 5.453571] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 5.475697] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 5.494005] xhci-mtk 1e1c0000.xhci: irq 21, io mem 0x1e1c0000
[ 5.506930] hub 1-0:1.0: USB hub found
[ 5.514567] hub 1-0:1.0: 2 ports detected
[ 5.523234] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 5.533903] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 5.548848] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 5.561765] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.578904] hub 2-0:1.0: USB hub found
[ 5.586504] hub 2-0:1.0: 1 port detected
[ 5.634765] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.655938] init: - preinit -
[ 5.981516] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-mtk
[ 6.019021] random: procd: uninitialized urandom read (4 bytes read)
[ 6.669131] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 6.685406] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6.702289] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.827977] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.901531] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.053594] urandom_read: 3 callbacks suppressed
[ 7.053608] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.103149] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.151258] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.225009] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 7.238701] 8021q: adding VLAN 0 to HW filter on device lan1
[ 11.339992] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.355002] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 11.603504] jffs2: notice: (640) jffs2_build_xattr_subsystem: complete building xattr subsystem, 30 of xdatum (26 unchecked, 4 orphan) and 39 of xref (4 dead, 0 orphan) found.
[ 11.659719] mount_root: loading kmods from internal overlay
[ 11.836064] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 11.921186] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 11.934076] scsi host0: usb-storage 2-1:1.0
[ 11.943968] usbcore: registered new interface driver usb-storage
[ 11.956588] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 12.403816] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.421026] block: extroot: not configured
[ 12.431044] mount_root: switching to jffs2 overlay
[ 12.445976] overlayfs: upper fs does not support tmpfile.
[ 12.462769] urandom-seed: Seeding with /etc/urandom.seed
[ 12.523276] mt7530 mdio-bus:1f lan1: Link is Down
[ 12.568662] procd: - early -
[ 12.574568] procd: - watchdog -
[ 12.587834] crng init done
[ 12.593293] random: 1 urandom warning(s) missed due to ratelimiting
[ 12.973071] scsi 0:0:0:0: Direct-Access Kingston DT microDuo 3C PMAP PQ: 0 ANSI: 6
[ 12.993375] sd 0:0:0:0: [sda] 121110528 512-byte logical blocks: (62.0 GB/57.8 GiB)
[ 13.009806] sd 0:0:0:0: [sda] Write Protect is off
[ 13.019500] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[ 13.020096] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 13.090303] sda: sda1 sda2
[ 13.101293] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 13.603735] procd: - watchdog -
[ 13.612156] procd: - ubus -
[ 13.771935] procd: - init -
[ 14.485053] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.521634] Loading modules backported from Linux version v5.10.85-0-ge4f2aee6612e
[ 14.537069] Backport generated by backports.git v5.10.85-1-0-gf988973f
[ 14.568296] usbcore: registered new interface driver ums-alauda
[ 14.581858] usbcore: registered new interface driver ums-cypress
[ 14.595708] usbcore: registered new interface driver ums-datafab
[ 14.609270] usbcore: registered new interface driver ums-freecom
[ 14.622978] usbcore: registered new interface driver ums-isd200
[ 14.636698] usbcore: registered new interface driver ums-jumpshot
[ 14.650517] usbcore: registered new interface driver ums-karma
[ 14.666424] usbcore: registered new interface driver ums-sddr09
[ 14.680153] usbcore: registered new interface driver ums-sddr55
[ 14.693925] usbcore: registered new interface driver ums-usbat
[ 14.715689] xt_time: kernel timezone is -0000
[ 14.767935] urngd: v1.0.2 started.
[ 14.797613] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=24
[ 14.808480] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 14.819800] mt76x2e 0000:01:00.0: enabling device (0000 -> 0002)
[ 14.832178] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[ 15.240539] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[ 15.258613] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[ 15.269641] mt76x2e 0000:01:00.0: Build: 1
[ 15.277814] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[ 15.303498] mt76x2e 0000:01:00.0: Firmware running!
[ 15.315859] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.321545] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=25
[ 15.332474] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 15.344212] mt76x2e 0000:02:00.0: ASIC revision: 76020044
[ 15.755583] mt76x2e 0000:02:00.0: ROM patch already applied
[ 15.767991] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[ 15.778976] mt76x2e 0000:02:00.0: Build: 1
[ 15.787145] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[ 15.802453] mt76x2e 0000:02:00.0: Firmware running!
[ 15.814794] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 15.846230] PPP generic driver version 2.4.2
[ 15.856720] NET: Registered protocol family 24
[ 15.882392] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 22.756976] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 22.782498] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 22.798850] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 22.806746] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 22.831091] 8021q: adding VLAN 0 to HW filter on device lan1
[ 22.851075] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.864802] br-lan: port 1(lan1) entered blocking state
[ 22.875387] br-lan: port 1(lan1) entered disabled state
[ 22.887758] device lan1 entered promiscuous mode
[ 22.897155] device eth0 entered promiscuous mode
[ 22.939634] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 22.953775] 8021q: adding VLAN 0 to HW filter on device lan2
[ 22.969569] br-lan: port 2(lan2) entered blocking state
[ 22.980110] br-lan: port 2(lan2) entered disabled state
[ 22.992135] device lan2 entered promiscuous mode
[ 23.013188] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 23.027211] 8021q: adding VLAN 0 to HW filter on device lan3
[ 23.042166] br-lan: port 3(lan3) entered blocking state
[ 23.052780] br-lan: port 3(lan3) entered disabled state
[ 23.064922] device lan3 entered promiscuous mode
[ 23.086021] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 23.100461] 8021q: adding VLAN 0 to HW filter on device lan4
[ 23.116461] br-lan: port 4(lan4) entered blocking state
[ 23.127016] br-lan: port 4(lan4) entered disabled state
[ 23.140185] device lan4 entered promiscuous mode
[ 23.175038] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 23.189020] 8021q: adding VLAN 0 to HW filter on device wan
[ 26.923992] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 26.939000] br-lan: port 1(lan1) entered blocking state
[ 26.949442] br-lan: port 1(lan1) entered forwarding state
[ 26.961154] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 27.275998] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 27.290806] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
[ 719.956561] usb 2-1: USB disconnect, device number 2
[11217.684667] usb 2-1: new SuperSpeed Gen 1 USB device number 3 using xhci-mtk
[11217.720247] usb-storage 2-1:1.0: USB Mass Storage device detected
[11217.733485] scsi host0: usb-storage 2-1:1.0
[11218.761771] scsi 0:0:0:0: Direct-Access Kingston DT microDuo 3C PMAP PQ: 0 ANSI: 6
[11218.781801] sd 0:0:0:0: [sda] 121110528 512-byte logical blocks: (62.0 GB/57.8 GiB)
[11218.797490] sd 0:0:0:0: [sda] Write Protect is off
[11218.807080] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
[11218.807480] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[11218.877550] sda: sda1 sda2
[11218.886565] sd 0:0:0:0: [sda] Attached SCSI removable disk
root@OpenWrt:~# opkg list-installed
base-files - 1439-r16495-bf0c965af0
block-mount - 2021-01-04-c53b1882-1
busybox - 1.33.2-2
ca-bundle - 20210119-1
cgi-io - 2021-09-08-98cef9dd-20
dnsmasq - 2.85-8
dropbear - 2020.81-2
firewall - 2021-03-23-61db17ed-1
fstools - 2021-01-04-c53b1882-1
fwtool - 2019-11-12-8f7fe925-1
getrandom - 2020-10-25-9ef88681-2
hdparm - 9.60-1
hostapd-common - 2020-06-08-5a8b3662-39
htop - 3.1.2-1
ip6tables - 1.8.7-1
iptables - 1.8.7-1
iw - 5.9-8fab0c9e-3
iwinfo - 2021-04-30-c45f0b58-2.1
jshn - 2021-05-16-b14c4688-2
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 5.4.179-1-613e7cb33f069740a878d322bb79ae77
kmod-ata-ahci - 5.4.179-1
kmod-ata-core - 5.4.179-1
kmod-ata-via-sata - 5.4.179-1
kmod-cfg80211 - 5.4.179+5.10.85-1-1
kmod-gpio-button-hotplug - 5.4.179-3
kmod-ip6tables - 5.4.179-1
kmod-ipt-conntrack - 5.4.179-1
kmod-ipt-core - 5.4.179-1
kmod-ipt-nat - 5.4.179-1
kmod-ipt-offload - 5.4.179-1
kmod-leds-gpio - 5.4.179-1
kmod-lib-crc-ccitt - 5.4.179-1
kmod-mac80211 - 5.4.179+5.10.85-1-1
kmod-mmc - 5.4.179-1
kmod-mt76-core - 5.4.179+2021-12-03-678071ef-4
kmod-mt76x02-common - 5.4.179+2021-12-03-678071ef-4
kmod-mt76x2 - 5.4.179+2021-12-03-678071ef-4
kmod-mt76x2-common - 5.4.179+2021-12-03-678071ef-4
kmod-nf-conntrack - 5.4.179-1
kmod-nf-conntrack6 - 5.4.179-1
kmod-nf-flow - 5.4.179-1
kmod-nf-ipt - 5.4.179-1
kmod-nf-ipt6 - 5.4.179-1
kmod-nf-nat - 5.4.179-1
kmod-nf-reject - 5.4.179-1
kmod-nf-reject6 - 5.4.179-1
kmod-nls-base - 5.4.179-1
kmod-ppp - 5.4.179-1
kmod-pppoe - 5.4.179-1
kmod-pppox - 5.4.179-1
kmod-scsi-core - 5.4.179-1
kmod-sdhci-mt7620 - 5.4.179-1
kmod-slhc - 5.4.179-1
kmod-usb-core - 5.4.179-1
kmod-usb-ledtrig-usbport - 5.4.179-1
kmod-usb-storage - 5.4.179-1
kmod-usb-storage-extras - 5.4.179-1
kmod-usb3 - 5.4.179-1
libblobmsg-json20210516 - 2021-05-16-b14c4688-2
libc - 1.1.24-3
libevdev - 1.12.0-1
libgcc1 - 8.4.0-3
libip4tc2 - 1.8.7-1
libip6tc2 - 1.8.7-1
libiwinfo-data - 2021-04-30-c45f0b58-2.1
libiwinfo-lua - 2021-04-30-c45f0b58-2.1
libiwinfo20210430 - 2021-04-30-c45f0b58-2.1
libjson-c5 - 0.15-2
libjson-script20210516 - 2021-05-16-b14c4688-2
libkmod - 27-2
liblua5.1.5 - 5.1.5-9
liblucihttp-lua - 2021-06-11-3dc89af4-1
liblucihttp0 - 2021-06-11-3dc89af4-1
libncurses6 - 6.2-3
libnl-tiny1 - 2020-08-05-c291088f-2
libpci - 3.7.0-2
libpthread - 1.1.24-3
librt - 1.1.24-3
libubox20210516 - 2021-05-16-b14c4688-2
libubus-lua - 2021-06-30-4fc532c8-2
libubus20210630 - 2021-06-30-4fc532c8-2
libuci20130104 - 2021-04-14-4b3db117-5
libuclient20201210 - 2021-05-14-6a6011df-1
libudev-zero - 1.0.0-1
libusb-1.0-0 - 1.0.24-4
libustream-wolfssl20201210 - 2022-01-16-868fd881-1
libwolfssl5.1.1.99a5b54a - 5.1.1-stable-1
libxtables12 - 1.8.7-1
logd - 2020-10-25-9ef88681-2
lua - 5.1.5-9
luci - git-20.074.84698-ead5e81
luci-app-firewall - git-22.046.85957-59c3392
luci-app-opkg - git-21.312.69848-4745991
luci-base - git-22.046.85957-59c3392
luci-lib-base - git-20.232.39649-1f6dc29
luci-lib-ip - git-20.250.76529-62505bd
luci-lib-jsonc - git-19.317.29469-8da8f38
luci-lib-nixio - git-20.234.06894-c4a4e43
luci-mod-admin-full - git-19.253.48496-3f93650
luci-mod-network - git-22.046.85061-dd54dce
luci-mod-status - git-22.046.85784-0ac2542
luci-mod-system - git-22.019.40321-7a37d02
luci-proto-ipv6 - git-21.148.49484-14511e5
luci-proto-ppp - git-21.163.64918-6c6559a
luci-ssl - git-20.244.36115-e10f954
luci-theme-bootstrap - git-22.047.35373-cc582eb
mtd - 26
netifd - 2021-10-30-8f82742c-1
odhcp6c - 2021-01-09-53f07e90-16
odhcpd-ipv6only - 2021-07-18-bc9d317f-3
openwrt-keyring - 2021-02-20-49283916-2
opkg - 2021-06-13-1bf042dd-1
pciids - 0.354-1
pciutils - 3.7.0-2
ppp - 2.4.8.git-2020-10-03-3
ppp-mod-pppoe - 2.4.8.git-2020-10-03-3
procd - 2021-03-08-2cfc26f8-1
px5g-wolfssl - 3
rpcd - 2021-03-11-ccb75178-1
rpcd-mod-file - 2021-03-11-ccb75178-1
rpcd-mod-iwinfo - 2021-03-11-ccb75178-1
rpcd-mod-luci - 20210614
rpcd-mod-rrdns - 20170710
terminfo - 6.2-3
ubi-utils - 2.1.2-1
ubox - 2020-10-25-9ef88681-2
ubus - 2021-06-30-4fc532c8-2
ubusd - 2021-06-30-4fc532c8-2
uci - 2021-04-14-4b3db117-5
uclient-fetch - 2021-05-14-6a6011df-1
uhttpd - 2021-03-21-15346de8-2
uhttpd-mod-ubus - 2021-03-21-15346de8-2
urandom-seed - 3
urngd - 2020-01-21-c7f7b6b6-1
usbids - 0.354-1
usbutils - 013-2
usign - 2020-05-23-f1f65026-1
wireless-regdb - 2021.08.28-1
wpad-basic-wolfssl - 2020-06-08-5a8b3662-39
zlib - 1.2.11-4