Wi-Fi is not associated

sharbich · November 26, 2019, 12:03pm

Hi,
i installed the following WLAN cards in my APU 1D4 board:

04:00.0 Network controller: Qualcomm Atheros AR928X Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Qualcomm Atheros Device 3099
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Exit Latency L1 <64us
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
		LnkCtl:	ASPM L1 Enabled; RCB 128 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [90] MSI-X: Enable- Count=1 Masked-
		Vector table: BAR=0 offset=00000000
		PBA: BAR=0 offset=00000000
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		AERCap:	First Error Pointer: 14, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: ath9k

06:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 27
	Region 0: Memory at f7400000 (64-bit, non-prefetchable) [size=2M]
	Expansion ROM at f7600000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
		Address: fee0300c  Data: 4162
		Masking: 00fe00fe  Pending: 00000000
	Capabilities: [70] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
			 AtomicOpsCap: 32bit- 64bit- 128bitCAS-
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
			 AtomicOpsCtl: ReqEn-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
			MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
		HeaderLog: 00000000 00000000 00000000 00000000
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: ath10k_pci

When I boot, I see the following error messages:

root@rome01:~# dmesg | grep ath
[   10.810431] ath10k_pci 0000:06:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.053851] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:06:00.0.bin failed with error -2
[   11.064684] ath10k_pci 0000:06:00.0: Falling back to user helper
[   12.973342] firmware ath10k!pre-cal-pci-0000:06:00.0.bin: firmware_loading_store: map pages failed
[   12.982688] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/cal-pci-0000:06:00.0.bin failed with error -2
[   12.993188] ath10k_pci 0000:06:00.0: Falling back to user helper
[   13.008526] firmware ath10k!cal-pci-0000:06:00.0.bin: firmware_loading_store: map pages failed
[   13.023588] ath10k_pci 0000:06:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[   13.032946] ath10k_pci 0000:06:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.043132] ath10k_pci 0000:06:00.0: firmware ver 10.2.4-1.0-00037 api 6 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
[   13.088707] ath10k_pci 0000:06:00.0: found invalid board magic
[   13.095084] ath10k_pci 0000:06:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.235813] ath10k_pci 0000:06:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   14.352821] ath: EEPROM regdomain: 0x0
[   14.352830] ath: EEPROM indicates default country code should be used
[   14.352833] ath: doing EEPROM country->regdmn map search
[   14.352838] ath: country maps to regdmn code: 0x3a
[   14.352841] ath: Country alpha2 being used: US
[   14.352844] ath: Regpair used: 0x3a
[   14.372804] usbcore: registered new interface driver ath9k_htc
[   14.806642] ath: phy3: ASPM enabled: 0x2
[   14.810656] ath: EEPROM regdomain: 0x0
[   14.810659] ath: EEPROM indicates default country code should be used
[   14.810661] ath: doing EEPROM country->regdmn map search
[   14.810666] ath: country maps to regdmn code: 0x3a
[   14.810669] ath: Country alpha2 being used: US
[   14.810671] ath: Regpair used: 0x3a
[   19.270771] ath: EEPROM regdomain: 0x8114
[   19.274857] ath: EEPROM indicates we should expect a country code
[   19.281005] ath: doing EEPROM country->regdmn map search
[   19.286372] ath: country maps to regdmn code: 0x37
[   19.291195] ath: Country alpha2 being used: DE
[   19.295653] ath: Regpair used: 0x37
[   19.299154] ath: regdomain 0x8114 dynamically updated by user
[   19.305021] ath: EEPROM regdomain: 0x8114
[   19.309085] ath: EEPROM indicates we should expect a country code
[   19.315205] ath: doing EEPROM country->regdmn map search
[   19.320542] ath: country maps to regdmn code: 0x37
[   19.325344] ath: Country alpha2 being used: DE
[   19.329798] ath: Regpair used: 0x37
[   19.333317] ath: regdomain 0x8114 dynamically updated by user

I have installed the following packages:

ath10k-firmware-qca988x	2018-05-12-952afa49-1	
ath9k-htc-firmware	2017-09-06-a61ac5cf-1	
kmod-ath	4.14.131+2017-11-01-10	
kmod-ath10k	4.14.131+2017-11-01-10	
kmod-ath9k	4.14.131+2017-11-01-10	
kmod-ath9k-common	4.14.131+2017-11-01-10	
kmod-ath9k-htc	4.14.131+2017-11-01-10

The following OpenWrt version is installed on my router:

OpenWrt 18.06.4 r7808-ef686b7292 / LuCI openwrt-18.06 branch (git-19.170.32094-4d6d8bc)

Do you have a tip where to look for the bug?
Greeting from Stefan

juppin · November 26, 2019, 12:22pm

Hello,

the errors about loading firmware and the fallback to the user space helper are almost normal for ath10k.

What are your contents in /lib/firmware after the first boot?

Probably you should switch the ath10k firmware to the CT variant as master and 19.07 does also use it for almost all ath10k chips.

Whats your contents of /etc/config/wireless?
If this file is empty, then remove it and call wifi from a shell and post the contents.

Note: For posting config files, use the preformattet text function of the board.

sharbich · November 26, 2019, 12:50pm

/lib/firmware:

/lib/firmware/
/lib/firmware/ath10k
/lib/firmware/ath10k/QCA988X
/lib/firmware/ath10k/QCA988X/hw2.0
/lib/firmware/ath10k/QCA988X/hw2.0/board.bin
/lib/firmware/ath10k/QCA988X/hw2.0/firmware-5.bin
/lib/firmware/ath9k_htc
/lib/firmware/ath9k_htc/htc_7010-1.4.0.fw
/lib/firmware/ath9k_htc/htc_9271-1.4.0.fw
/lib/firmware/regulatory.db
/lib/firmware/rtl_nic
/lib/firmware/rtl_nic/rtl8105e-1.fw
/lib/firmware/rtl_nic/rtl8106e-1.fw
/lib/firmware/rtl_nic/rtl8106e-2.fw
/lib/firmware/rtl_nic/rtl8107e-1.fw
/lib/firmware/rtl_nic/rtl8107e-2.fw
/lib/firmware/rtl_nic/rtl8168d-1.fw
/lib/firmware/rtl_nic/rtl8168d-2.fw
/lib/firmware/rtl_nic/rtl8168e-1.fw
/lib/firmware/rtl_nic/rtl8168e-2.fw
/lib/firmware/rtl_nic/rtl8168e-3.fw
/lib/firmware/rtl_nic/rtl8168f-1.fw
/lib/firmware/rtl_nic/rtl8168f-2.fw
/lib/firmware/rtl_nic/rtl8168g-1.fw
/lib/firmware/rtl_nic/rtl8168g-2.fw
/lib/firmware/rtl_nic/rtl8168g-3.fw
/lib/firmware/rtl_nic/rtl8168h-1.fw
/lib/firmware/rtl_nic/rtl8168h-2.fw
/lib/firmware/rtl_nic/rtl8402-1.fw
/lib/firmware/rtl_nic/rtl8411-1.fw
/lib/firmware/rtl_nic/rtl8411-2.fw

/etc/config/wireless:

root@rome01:~# cat /etc/config/wireless 

config wifi-device 'radio0'
	option type 'mac80211'
	option hwmode '11a'
	option path 'pci0000:00/0000:00:15.0/0000:06:00.0'
	option htmode 'VHT80'
	option legacy_rates '1'
	option channel '44'
	option country 'US'
	option txpower '23'

config wifi-iface
	option device 'radio0'
	option mode 'ap'
	option ssid 'Access-Point-.......'
	option encryption 'psk2+ccmp'
	option key 'decker.......'
	option network 'wlan'

config wifi-device 'radio1'
	option type 'mac80211'
	option path 'virtual/mac80211_hwsim/hwsim0'
	option hwmode '11g'
	option country 'DE'
	option htmode 'HT20'
	option channel '12'
	option txpower '17'

config wifi-device 'radio2'
	option type 'mac80211'
	option channel '36'
	option hwmode '11a'
	option path 'virtual/mac80211_hwsim/hwsim1'
	option htmode 'VHT160'
	option txpower '20'
	option country 'DE'

config wifi-device 'radio3'
	option type 'mac80211'
	option hwmode '11g'
	option path 'pci0000:00/0000:00:07.0/0000:04:00.0'
	option htmode 'HT40'
	option channel '10'
	option legacy_rates '1'
	option country 'US'
	option txpower '21'

config wifi-iface
	option device 'radio3'
	option mode 'ap'
	option ssid 'Access-Point-.......'
	option encryption 'psk2+ccmp'
	option key 'decker.......'
	option network 'wlan'

If this file is empty? No it is not.

The next i installet the CT variant.

mk24 · November 26, 2019, 12:58pm

Does iw dev show devices brought up? You should see the SSID and channel on a fully active AP.

Does the 'wlan' network exist? For initial testing connect them to the existing LAN and also use minimum bandwidth (HT20 or VHT20).

Status is normally "not associated" for a working but idle AP, until a client device connects.

juppin · November 26, 2019, 1:06pm

Seems everything fine from my point of view...
The radio1 and radio3 are your two attached pci wifi cards.

Do you have any bugs or trouble while setting up your new attached cards or you are only confused about the errors/messages in dmesg?

Don't know what radio2 is for...?

sharbich · November 26, 2019, 1:32pm

I deleted the file / etc / config / wireless and created a new file using wifi config
/ Etc / config / wireless:

root@rome01:~# cat /etc/config/wireless 

config wifi-device 'radio0'
	option type 'mac80211'
	option channel '36'
	option hwmode '11a'
	option path 'virtual/mac80211_hwsim/hwsim0'
	option htmode 'VHT20'
	option country 'US'
	option legacy_rates '1'
	option __toggle 'Aktivieren'

config wifi-iface 'default_radio0'
	option device 'radio0'
	option mode 'ap'
	option ssid 'OpenWrt'
	option encryption 'none'
	option network 'wlan'

config wifi-device 'radio1'
	option type 'mac80211'
	option channel '36'
	option hwmode '11a'
	option path 'virtual/mac80211_hwsim/hwsim1'
	option htmode 'VHT20'
	option disabled '1'

config wifi-iface 'default_radio1'
	option device 'radio1'
	option network 'lan'
	option mode 'ap'
	option ssid 'OpenWrt'
	option encryption 'none'

config wifi-device 'radio2'
	option type 'mac80211'
	option channel '36'
	option hwmode '11a'
	option path 'pci0000:00/0000:00:15.0/0000:06:00.0'
	option htmode 'VHT20'
	option disabled '1'

config wifi-iface 'default_radio2'
	option device 'radio2'
	option network 'lan'
	option mode 'ap'
	option ssid 'OpenWrt'
	option encryption 'none'

config wifi-device 'radio3'
	option type 'mac80211'
	option channel '36'
	option hwmode '11a'
	option path 'pci0000:00/0000:00:07.0/0000:04:00.0'
	option htmode 'HT20'
	option disabled '1'

config wifi-iface 'default_radio3'
	option device 'radio3'
	option network 'lan'
	option mode 'ap'
	option ssid 'OpenWrt'
	option encryption 'none'

iw dev:

root@rome01:~# iw dev
phy#3
	Interface wlan3
		ifindex 12
		wdev 0x300000001
		addr 04:f0:21:14:c8:36
		type managed
		txpower 17.00 dBm
phy#2
	Interface wlan2
		ifindex 11
		wdev 0x200000001
		addr 04:f0:21:1b:64:21
		type managed
		txpower 0.00 dBm
phy#1
	Interface wlan1
		ifindex 9
		wdev 0x100000001
		addr 02:00:00:00:01:00
		type managed
		txpower 0.00 dBm

dmesg | grep ath

root@rome01:~# dmesg | grep ath
[   10.926819] ath10k_pci 0000:06:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.165155] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:06:00.0.bin failed with error -2
[   11.175947] ath10k_pci 0000:06:00.0: Falling back to user helper
[   13.136253] firmware ath10k!pre-cal-pci-0000:06:00.0.bin: firmware_loading_store: map pages failed
[   13.145776] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/cal-pci-0000:06:00.0.bin failed with error -2
[   13.156270] ath10k_pci 0000:06:00.0: Falling back to user helper
[   13.170356] firmware ath10k!cal-pci-0000:06:00.0.bin: firmware_loading_store: map pages failed
[   13.183137] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   13.194007] ath10k_pci 0000:06:00.0: Falling back to user helper
[   13.208002] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   13.222482] ath10k_pci 0000:06:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[   13.231841] ath10k_pci 0000:06:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.242015] ath10k_pci 0000:06:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
[   13.287200] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.297708] ath10k_pci 0000:06:00.0: Falling back to user helper
[   13.313144] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.322692] ath10k_pci 0000:06:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.462917] ath10k_pci 0000:06:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   14.582703] ath: EEPROM regdomain: 0x0
[   14.582712] ath: EEPROM indicates default country code should be used
[   14.582715] ath: doing EEPROM country->regdmn map search
[   14.582720] ath: country maps to regdmn code: 0x3a
[   14.582724] ath: Country alpha2 being used: US
[   14.582726] ath: Regpair used: 0x3a
[   14.599808] usbcore: registered new interface driver ath9k_htc
[   15.035338] ath: phy3: ASPM enabled: 0x2
[   15.039339] ath: EEPROM regdomain: 0x0
[   15.039343] ath: EEPROM indicates default country code should be used
[   15.039345] ath: doing EEPROM country->regdmn map search
[   15.039349] ath: country maps to regdmn code: 0x3a
[   15.039352] ath: Country alpha2 being used: US
[   15.039354] ath: Regpair used: 0x3a

Then I try to install the version 19.07 times.

sharbich · November 26, 2019, 1:48pm

If I activate my WLAN on the Smartphone I do not see the SSID. Why?

sharbich · November 26, 2019, 2:16pm

Hi,
in syslog I see the following error messages.

Tue Nov 26 14:20:14 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna all all
Tue Nov 26 14:20:14 2019 daemon.notice netifd: radio0 (12145): command failed: Operation not supported (-95)
Tue Nov 26 14:20:14 2019 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Tue Nov 26 14:20:23 2019 user.notice mac80211: Failed command: iw phy phy0 set antenna all all
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): command failed: Operation not supported (-95)
Tue Nov 26 14:20:23 2019 user.notice mac80211: Failed command: iw phy phy0 set distance 0
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): ./mac80211.sh: eval: line 1: /usr/sbin/hostapd: not found
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): WARNING (wireless_add_process): executable path /usr/sbin/wpad does not match process >
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): Command failed: Invalid argument
Tue Nov 26 14:20:23 2019 daemon.notice netifd: radio0 (13629): Device setup failed: HOSTAPD_START_FAILED

mk24 · November 26, 2019, 2:16pm

Check in OpenWrt if the AP is active.

root@OpenWrt:~# iw dev
phy#0
	Interface wlan0-1
		ifindex 20
		wdev 0x9
		addr b6:fb <redacted>
		ssid <redacted>
		type AP
		channel 149 (5745 MHz), width: 80 MHz, center1: 5775 MHz
		txpower 30.00 dBm
		multicast TXQ:
			qsz-byt	qsz-pkt	flows	drops	marks	overlmt	hashcoltx-bytes	tx-packets
			0	0	417	0	0	0	0	34494		417

If you see only part of this, without the channel: and ssid: lines, the AP is not fully active-- and the error that causes this problem should be found in the kernel log.

mk24 · November 26, 2019, 2:20pm

Is a wpad package installed? usr/sbin/hostapd should exist and be a link to /usr/sbin/wpad.

sharbich · November 26, 2019, 2:27pm

Yes, package is installed. Links available.

anon4457646 · November 26, 2019, 2:41pm

ifconfig wlan2 up
not sure if that will do something , but your txpower is 0

sharbich · November 26, 2019, 2:51pm

In the LUCI WebGui, I only get a result from the Radio2 and Radio3 adapters under Network WLAN scan. Radio0 and Radio1 are not scanning.

anon4457646 · November 26, 2019, 2:54pm

something is strange here. do you have any phy0 wlan0? in general openwrt see the first radio phy0 wlan0 and i don't see that in your log