Why won't radio0 start?

I got OpenWRT up and running but I can't seem to get up the radio0 which is 60g. I thought it was the drivers so I uninstalled and reinstalled and the radio0 came up but as soon as I added a SSID to it when down and will not come up. I deleted the SSID and restarted nothing. Anything would help.

kern.err kernel: [ 2118.683744] wil6210 0002:01:00.0 wlan0: wil_cfg80211_del_iface: cannot remove the main interface
daemon.notice netifd: radio0 (12439): command failed: Not supported (-95)
kern.err kernel: [ 2118.865579] wil6210 0002:01:00.0 wlan0: wil_cfg80211_add_iface: virtual interfaces not supported
daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY
kern.info kernel: [ 2118.887467] wil6210 0002:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=3
kern.info kernel: [ 2118.887500] wil6210 0002:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=3
kern.info kernel: [ 2118.974349] wil6210 0002:01:00.0 wlan0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:97:3c RF = 0x0000 (status 0x0000) bband = 0x00000000
kern.info kernel: [ 2118.974388] wil6210 0002:01:00.0 wlan0: wil_get_bl_info: Boot Loader build 255.255.0.6836
kern.info kernel: [ 2118.987879] wil6210 0002:01:00.0 wlan0: wil_set_oob_mode: oob_mode to 0
kern.info kernel: [ 2118.996083] wil6210 0002:01:00.0 wlan0: wil_reset: Use firmware <wil6210.fw> + board <wil6210.brd>
kern.info kernel: [ 2119.039584] wil6210 0002:01:00.0 wlan0: wmi_evt_ready: FW ver. 5.2.0.18(SW 18); MAC 04:ce:14:0b:97:3c; 0 MID's
kern.info kernel: [ 2119.039635] wil6210 0002:01:00.0 wlan0: wil_wait_for_fw_ready: FW ready after 10 ms. HW version 0x00000001
kern.info kernel: [ 2119.049778] wil6210 0002:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_CNT_TRSH = 500 usec
kern.info kernel: [ 2119.058195] wil6210 0002:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_TX_IDL_CNT_TRSH = 13 usec
kern.info kernel: [ 2119.067952] wil6210 0002:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_CNT_TRSH = 500 usec
kern.info kernel: [ 2119.077881] wil6210 0002:01:00.0 wlan0: wil_configure_interrupt_moderation: set ITR_RX_IDL_CNT_TRSH = 13 usec
kern.info kernel: [ 2119.087379] wil6210 0002:01:00.0 wlan0: wil_refresh_fw_capabilities: keep_radio_on_during_sleep (0)
kern.info kernel: [ 2119.101044] br-lan: port 4(wlan0) entered blocking state
kern.info kernel: [ 2119.106189] br-lan: port 4(wlan0) entered disabled state
kern.info kernel: [ 2119.112515] device wlan0 entered promiscuous mode
daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
daemon.notice hostapd: Could not determine operating frequency
daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->DISABLED
daemon.notice hostapd: wlan0: AP-DISABLED
daemon.err hostapd: wlan0: Unable to setup interface.
daemon.notice hostapd: nl80211: deinit ifname=wlan0 disabled_11b_rates=0
kern.info kernel: [ 2119.154899] device wlan0 left promiscuous mode
kern.info kernel: [ 2119.154989] br-lan: port 4(wlan0) entered disabled state
kern.info kernel: [ 2119.216279] wil6210 0002:01:00.0 wlan0: _wil6210_disconnect: disconnect bssid=(null), reason=3
kern.info kernel: [ 2119.216312] wil6210 0002:01:00.0 wlan0: _wil6210_disconnect_complete: disconnect_complete: bssid=(null), reason=3
kern.info kernel: [ 2119.307577] wil6210 0002:01:00.0 wlan0: wil_get_bl_info: Boot Loader struct v2: MAC = 04:ce:14:0b:97:3c RF = 0x0000 (status 0x0000) bband = 0x00000000
kern.info kernel: [ 2119.307614] wil6210 0002:01:00.0 wlan0: wil_get_bl_info: Boot Loader build 255.255.0.6836
kern.info kernel: [ 2119.320013] wil6210 0002:01:00.0 wlan0: wil_set_oob_mode: oob_mode to 0
daemon.notice hostapd: wlan0: CTRL-EVENT-TERMINATING
daemon.err hostapd: hostapd_free_hapd_data: Interface wlan0 wasn't started
daemon.notice netifd: radio0 (12439): Command failed: Invalid argument
daemon.notice netifd: radio0 (12439): Device setup failed: HOSTAPD_START_FAILED
daemon.notice netifd: Wireless device 'radio0' set retry=0
daemon.crit netifd: Wireless device 'radio0' setup failed, retry=0
daemon.notice netifd: Wireless device 'radio0' is now down

Run the following (all at once) and post the results.

ubus call system board; \
uci export network; uci export wireless; \
uci export dhcp; uci export firewall; \
head -n -0 /etc/firewall.user; \
ip -4 addr ; ip -4 ro li tab all ; ip -4 ru; \
ip -6 addr ; ip -6 ro li tab all ; ip -6 ru; \
ls -l  /etc/resolv.* /tmp/resolv.* /tmp/resolv.*/* ; head -n -0 /etc/resolv.* /tmp/resolv.* /tmp/resolv.*/*

Note: Redact any passwords, and your public IP

Run opkg list-installed | grep 'wil6210' and post the results.

1 Like

I will try this when I get home.