Wavlink WL-WN570HA1 - new release hardware

For Developers
41

I am able to select 20 dBM but had left it at "driver default".
But indeed 2.5G is not working for me, but maybe ther's a network setup issue on my side, I have modified br-lan to bridge eth0.9 my VLAN ID 9, the device is able to pickup an IP over DHCP and even when I'm setting it a static IP on my network I am able to administer it, it is able to ping my opnSense router, I can ping it, all fine.
I can connect a client device to it using 2.5G it is able to get an IP over DHCP (my opnSense router does provide DHCP on this VLAN9), but even giving the client a static IP still doesn't work : from the wifi client I can't ping either to the AP or my router both being on VLAN9... Reverse is also true, router can't ping the wifi client

Maybe a config issue on my end, firewall in openwrt I'm quite unfamiliar with...

42

What country code do you have selected in your 2.4 GHz settings?

43

none :
image

44

you need to set your country,

45

What effect does this have if the installed power does not comply with the legislation of my country?

46

effect for who ?

you should reduce it to whatever's allowed.

47

What if it is almost three times less than the maximum allowed? How can I increase it?

48 
root@WN570HA1:~# iw reg get
global
country RU: DFS-UNSET
        (2400 - 2483 @ 40), (N/A, 20), (N/A)
        (5150 - 5350 @ 160), (N/A, 20), (N/A), NO-OUTDOOR
        (5650 - 5850 @ 160), (N/A, 20), (N/A), NO-OUTDOOR
        (5925 - 6425 @ 160), (N/A, 20), (N/A), NO-OUTDOOR
        (57000 - 66000 @ 2160), (N/A, 40), (N/A), NO-OUTDOOR

root@WN570HA1:~# iw phy phy0 info
Wiphy phy0
        wiphy index: 0
        max # scan SSIDs: 4
        max scan IEs length: 2257 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Available Antennas: TX 0x1 RX 0x1
        Configured Antennas: TX 0x1 RX 0x1
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * mesh point
                 * P2P-client
                 * P2P-GO
        Band 1:
                Capabilities: 0x17e
                        HT20/HT40
                        SM Power Save disabled
                        RX Greenfield
                        RX HT20 SGI
                        RX HT40 SGI
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        No DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: No restriction (0x00)
                HT TX/RX MCS rate indexes supported: 0-7
                Frequencies:
                        * 2412 MHz [1] (16.0 dBm)
                        * 2417 MHz [2] (16.0 dBm)
                        * 2422 MHz [3] (16.0 dBm)
                        * 2427 MHz [4] (16.0 dBm)
                        * 2432 MHz [5] (16.0 dBm)
                        * 2437 MHz [6] (16.0 dBm)
                        * 2442 MHz [7] (16.0 dBm)
                        * 2447 MHz [8] (16.0 dBm)
                        * 2452 MHz [9] (16.0 dBm)
                        * 2457 MHz [10] (16.0 dBm)
                        * 2462 MHz [11] (16.0 dBm)
                        * 2467 MHz [12] (16.0 dBm)
                        * 2472 MHz [13] (16.0 dBm)
                        * 2484 MHz [14] (disabled)
        valid interface combinations:
                 * #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 4,
                   total <= 4, #channels <= 1, STA/AP BI must match
        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Supported extended features:
                * [ RRM ]: RRM
                * [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
                * [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
                * [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
                * [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
                * [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
                * [ AQL ]: Airtime Queue Limits (AQL)
                * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
                * [ DEL_IBSS_STA ]: deletion of IBSS station support
                * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
                * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
root@WN570HA1:~# iwinfo phy0 txpower
   0 dBm (   1 mW)
   1 dBm (   1 mW)
   2 dBm (   1 mW)
   3 dBm (   1 mW)
   4 dBm (   2 mW)
   5 dBm (   3 mW)
   6 dBm (   3 mW)
   7 dBm (   5 mW)
   8 dBm (   6 mW)
   9 dBm (   7 mW)
  10 dBm (  10 mW)
  11 dBm (  12 mW)
  12 dBm (  15 mW)
  13 dBm (  19 mW)
  14 dBm (  25 mW)
  15 dBm (  31 mW)
* 16 dBm (  39 mW)
49

I did but still seems the AP is loosing wireless regularly, and even when connected I'm not getting IP connectivity ping doesn't work for me :frowning:

50

AFAIK the limits are in the regdb, if they're incorrect, they need to be updated.

51

The restrictions are correct - the wifi module does not work correctly...

52

Toxic0berliner
try this full build... 23.05/Wavlink/AERIAL HD2 WN570HA1/full

53

Thx @Morpheus68 ! But sadly WIFI doesn't work any better for me, regardless of the WPA level or even on open network, not able to even ping the wireless AP nor the router it's connected to :frowning:

54

How did you flash your patched image? I tried via intramfs it still boots to intramfs

55

Ok flashed via uboot so far so good working fine on 20dbm

56

I must have had something broken in my config that I previously kept while flashing your build that prevented wireless to work...
I have reflashed without keeping the config and set it up again and now wireless seems to work fine, vlans work fine... All good.

Only thing, probably you can't help it, upgrading packages or installing new ones fails mostly claiming a reference to a kernel that doesn't exist or read-only filesystem.
Probably this can be fixed when someone accepts your patch for mainstream?

Again, even as is the device is useful to me whereas it wasn't before your build so thanks a lot!

57

hello,
nobody find a good solution for wifi 5Ghz?
Morpheus firmware work well for all other functions ;(

thanks

58

hello,

do you try this change?

Thanks

59

Not on this device, but my understanding the mod should be very similar to Nexx WT3020, TP-Link MR3020 v1, etc.