VGV7519 from OpenWrt to LEDE

JEFFreal · October 26, 2017, 3:49pm

Hello,

I've installed on my Experia Box v8 a.k.a. VGV7519 OpenWRT today. Now i want to update to LEDE, but having some troubles with that. Normally i use the sysupgrade and flash it with LuCi. But this didn't work today
This is what i did:

UART MODE
Send .ASC File
md.l 0xb0000000 0x1000000   (makes a backup trough logging output can take 2 hours)
protect off all
erase all
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
tftpboot 0x80700000 u-boot.bin
cp.b 0x80700000 0xb0000000 ${filesize}

Power off router and remove jumper and caps

setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
set ethaddr XX:XX:XX:XX:XX:XX
saveenv
tftpboot 0x80700000 nor.image    (image taken from openwrt directory)
erase 0xB0080000 +${filesize}
cp.b 0x80700000 0xB0080000 ${filesize}
bootm 0xB0080000
reset
setenv bootdelay 2
setenv bootcmd bootm 0xB0080000
saveenv

After this i pushed the sysupgrade with LuCi but get a kernel panic see below

[    0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV7519NOR - KPN Experiabox V8
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 03e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15748
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00038080
[    0.000000] Readback ErrCtl register=00038080
[    0.000000] Memory: 56380K/63488K available (3914K kernel code, 161K rwdata, 884K rodata, 1232K init, 213K bss, 7108K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007856] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042325] pid_max: default: 32768 minimum: 301
[    0.047167] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067161] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.076863] pinctrl core: initialized pinctrl subsystem
[    0.083389] NET: Registered protocol family 16
[    0.092793] pinctrl-xway 1e100b10.pinmux: Init done
[    0.098321] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.208491] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.223564] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.229211]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.234466]   IO 0x000000001ae00000..0x000000001affffff
[    0.254077] gpio-stp-xway 1e100bb0.stp: Init done
[    0.259373] usbcore: registered new interface driver usbfs
[    0.264884] usbcore: registered new interface driver hub
[    0.270224] usbcore: registered new device driver usb
[    0.275666] PCI host bridge to bus 0000:00
[    0.279657] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.286563] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.293508] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.300364] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.308868] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.316547] clocksource: Switched to clocksource MIPS
[    0.322862] NET: Registered protocol family 2
[    0.328171] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.335062] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.341441] TCP: Hash tables configured (established 1024 bind 1024)
[    0.347961] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.353794] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360356] NET: Registered protocol family 1
[    0.371599] gptu: totally 6 16-bit timers/counters
[    0.376439] gptu: misc_register on minor 63
[    0.380550] gptu: succeeded to request irq 126
[    0.385017] gptu: succeeded to request irq 127
[    0.389534] gptu: succeeded to request irq 128
[    0.394047] gptu: succeeded to request irq 129
[    0.398561] gptu: succeeded to request irq 130
[    0.403075] gptu: succeeded to request irq 131
[    0.410794] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.416094] lantiq,vmmc 1f103000.vmmc: requested GPIO 493
[    0.421557] lantiq,vmmc 1f103000.vmmc: requested GPIO 492
[    0.427001] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[    0.433434] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.440755] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 39A0000
[    0.447086] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 39A0000
[    0.555530] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.561593] Crashlog allocated RAM at address 0x3d00000
[    0.589442] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.595161] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.609016] io scheduler noop registered
[    0.612832] io scheduler deadline registered (default)
[    0.618694] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.627586] console [ttyLTQ0] enabled
[    0.627586] console [ttyLTQ0] enabled
[    0.634912] bootconsole [early0] disabled
[    0.634912] bootconsole [early0] disabled
[    0.643873] lantiq nor flash device: 00800000 at 10000000
[    0.647994] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.657431] Amd/Fujitsu Extended Query Table at 0x0040
[    0.662562]   Amd/Fujitsu Extended Query version 1.1.
[    0.667598] number of CFI chips: 1
[    0.670994] lantiq nor flash device: 00800000 at 14800000
[    0.676500] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.685978] Amd/Fujitsu Extended Query Table at 0x0040
[    0.691110]   Amd/Fujitsu Extended Query version 1.1.
[    0.696145] number of CFI chips: 1
[    0.699537] Concatenating MTD devices:
[    0.703279] (0): "ltq_nor"
[    0.705975] (1): "ltq_nor"
[    0.708672] into device "10000000.nor-boot"
[    0.712897] 4 ofpart partitions found on MTD device 10000000.nor-boot
[    0.719302] Creating 4 MTD partitions on "10000000.nor-boot":
[    0.725062] 0x000000040000-0x000000050000 : "board_config"
[    0.734088] 0x000000000000-0x000000040000 : "uboot"
[    0.739676] 0x000000060000-0x000000070000 : "uboot_env"
[    0.745718] 0x000000080000-0x000001000000 : "firmware"
[    0.771821] 2 uimage-fw partitions found on MTD device firmware
[    0.776338] 0x000000080000-0x00000020ff7b : "kernel"
[    0.783029] 0x00000020ff7b-0x000001000000 : "rootfs"
[    0.788725] mtd: device 5 (rootfs) set to be root filesystem
[    0.793004] 1 squashfs-split partitions found on MTD device rootfs
[    0.799147] 0x000000590000-0x000001000000 : "rootfs_data"
[    0.909808] libphy: lantiq,xrx200-mdio: probed
[    0.922284] net-xrx200: invalid MAC, using random
[    0.989281] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    1.057254] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    1.125239] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.193238] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.200925] net-xrx200: invalid MAC, using random
[    1.265264] eth1: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.372642] ltq-cputemp cputemp@0: Current CPU die temperature: 47.0 Â°C
[    1.378192] wdt 1f8803f0.watchdog: Init done
[    1.386298] NET: Registered protocol family 10
[    1.397072] NET: Registered protocol family 17
[    1.400144] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.412740] 8021q: 802.1Q VLAN Support v1.8
[    1.427619] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.437418] Freeing unused kernel memory: 1232K (804dc000 - 80610000)
[    2.580741] init: Console is alive
[    2.582991] init: - watchdog -
[    4.047465] dwc2 1e101000.ifxhcd: requested GPIO 494
[    4.280697] eth0: port 4 got link
[    4.908748] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    4.912324] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    4.919686] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    4.925190] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.932627] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    4.940070] hub 1-0:1.0: USB hub found
[    4.943080] hub 1-0:1.0: 1 port detected
[    5.804753] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    5.808342] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    5.815667] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    5.821187] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.828626] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    5.836075] hub 2-0:1.0: USB hub found
[    5.839055] hub 2-0:1.0: 1 port detected
[    5.845341] init: - preinit -
[    6.600665] random: procd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.875274] jffs2: notice: (411) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.892393] mount_root: overlay filesystem has not been fully initialized yet
[    9.972888] mount_root: switching to jffs2 overlay
- config restore -
[   10.712136] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.942584] procd: - early -
[   10.944200] procd: - watchdog -
[   11.380693] eth0: port 4 lost link
[   11.612343] procd: - ubus -
[   11.708296] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.716798] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.725376] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.733897] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.743345] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.751821] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.761022] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.769997] random: ubusd: uninitialized urandom read (4 bytes read, 50 bits of entropy available)
[   11.779228] procd: - init -
Please press Enter to activate this console.
[   12.249247] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   12.263420] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   12.275379] NET: Registered protocol family 8
[   12.278355] NET: Registered protocol family 20
[   12.289316] PPP generic driver version 2.4.2
[   12.299727] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.324380] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG

Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   12.346503]
[   12.346503] Predefined debug level: 3
[   12.358636] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[   12.364830] Backport generated by backports.git backports-20160324-9-g0e38f5c
[   12.383891] Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   12.391246] request_timer(2, 0x000001AE, 1)...successful!
[   12.396830] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   12.407965] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.417136] Infineon Technologies DEU driver version 2.0.0
[   12.423298] IFX DEU DES initialized (multiblock).
[   12.427612] IFX DEU AES initialized (multiblock).
[   12.431726] IFX DEU ARC4 initialized (multiblock).
[   12.436407] IFX DEU SHA1 initialized.
[   12.439946] IFX DEU MD5 initialized.
[   12.443575] IFX DEU SHA1_HMAC initialized.
[   12.447606] IFX DEU MD5_HMAC initialized.
[   12.458947] nf_conntrack version 0.5.0 (900 buckets, 3600 max)
[   12.484164] NET: Registered protocol family 24
[   12.507506] xt_time: kernel timezone is -0000
[   12.596217] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   12.600956] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[   12.607897] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   12.615675] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0xffff detected
[   12.623899] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[   12.631472] ------------[ cut here ]------------
[   12.636074] WARNING: CPU: 0 PID: 494 at mm/vmalloc.c:1460 0x80223eb8()
[   12.642582] Trying to vfree() bad address (83368400)
[   12.647535] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   12.720112] CPU: 0 PID: 494 Comm: kmodloader Not tainted 4.4.50 #0
[   12.726319] Stack : 80616882 00000036 80616882 00000001 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          ...
[   12.761789] Call Trace:[<80017660>] 0x80017660
[   12.766267] [<80017660>] 0x80017660
[   12.769747] [<80223eb8>] 0x80223eb8
[   12.773234] [<8002ddc0>] 0x8002ddc0
[   12.776717] [<80223eb8>] 0x80223eb8
[   12.780165] [<8002de1c>] 0x8002de1c
[   12.783697] [<80223eb8>] 0x80223eb8
[   12.787186] [<82c575dc>] 0x82c575dc [rt2x00lib@82c50000+0x8c70]
[   12.793098] [<82c51d90>] 0x82c51d90 [rt2x00lib@82c50000+0x8c70]
[   12.799011] [<801e95d8>] 0x801e95d8
[   12.802497] [<82c6724c>] 0x82c6724c [rt2x00pci@82c67000+0x5c0]
[   12.808311] [<80213091>] 0x80213091
[   12.811791] [<801f4760>] 0x801f4760
[   12.815272] [<8021d3bc>] 0x8021d3bc
[   12.818749] [<8021dbe0>] 0x8021dbe0
[   12.822233] [<800a249c>] 0x800a249c
[   12.825722] [<8021de58>] 0x8021de58
[   12.829199] [<8021ddcc>] 0x8021ddcc
[   12.832677] [<8021bc34>] 0x8021bc34
[   12.836126] [<803d1bb4>] 0x803d1bb4
[   12.839641] [<8004c944>] 0x8004c944
[   12.843129] [<8021d0b4>] 0x8021d0b4
[   12.846595] [<80040eb4>] 0x80040eb4
[   12.850097] [<833f9000>] 0x833f9000 [rt2800pci@82c5c000+0x1010]
[   12.856006] [<8021e49c>] 0x8021e49c
[   12.859502] [<833f9000>] 0x833f9000 [rt2800pci@82c5c000+0x1010]
[   12.865412] [<8000c88c>] 0x8000c88c
[   12.868894] [<8003e8c8>] 0x8003e8c8
[   12.872356] [<800779a0>] 0x800779a0
[   12.875857] [<800b8fe4>] 0x800b8fe4
[   12.879344] [<80078fec>] 0x80078fec
[   12.882811] [<80076fc8>] 0x80076fc8
[   12.886307] [<800b9540>] 0x800b9540
[   12.889780] [<800b9624>] 0x800b9624
[   12.893259] [<800794b4>] 0x800794b4
[   12.896749] [<8000482c>] 0x8000482c
[   12.900190] [<80006c58>] 0x80006c58
[   12.903701]
[   12.905168] ---[ end trace 2c87884f5734b28c ]---
[   12.909798] Kernel bug detected[#1]:
[   12.913337] CPU: 0 PID: 494 Comm: kmodloader Tainted: G        W       4.4.50 #0
[   12.920731] task: 83904a10 ti: 8324e000 task.ti: 8324e000
[   12.926122] $ 0   : 00000000 80017660 81062c60 00000000
[   12.931344] $ 4   : 82c58c60 ffffffff 00000009 00000000
[   12.936566] $ 8   : 0000002d 00004be0 00000000 00000000
[   12.941789] $12   : 000000fd 000000fd 00000000 00000000
[   12.947011] $16   : 8312d460 804b6060 8312d734 ffffffed
[   12.952233] $20   : 82c5cb6c 80640000 0000000a 804385c0
[   12.957456] $24   : 00000003 00000000
[   12.962678] $28   : 8324e000 8324fb70 804c0000 82c575dc
[   12.967901] Hi    : 0000005a
[   12.970774] Lo    : 828f5d93
[   12.973650] epc   : 800c1818 0x800c1818
[   12.977485] ra    : 82c575dc 0x82c575dc [rt2x00lib@82c50000+0x8c70]
[   12.983742] Status: 1100fd03 KERNEL EXL IE
[   12.987922] Cause : 10800024 (ExcCode 09)
[   12.991926] PrId  : 00019556 (MIPS 34Kc)
[   12.995840] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   13.068439] Process kmodloader (pid: 494, threadinfo=8324e000, task=83904a10, tls=7766dd48)
[   13.076787] Stack : 00000000 8324fb90 8312d460 804b6060 8312d460 82c51d90 00000f10 8324fba0
          82c57794 00000000 00000000 82ced080 00000000 8324fbf6 00000001 801e95d8
          8312c160 838a6800 838a6800 8312d460 02400000 8312cb40 82c5cb6c 80640000
          0000000a 804385c0 804c0000 82c6724c 0000000a 804385c0 804c0000 82c5ce54
          838a6868 80213091 82c5ce54 838a6868 838a6800 82c5ce20 82c5ce54 801f4760
          ...
[   13.112299] Call Trace:[<82c51d90>] 0x82c51d90 [rt2x00lib@82c50000+0x8c70]
[   13.119193] [<801e95d8>] 0x801e95d8
[   13.122681] [<82c6724c>] 0x82c6724c [rt2x00pci@82c67000+0x5c0]
[   13.128494] [<80213091>] 0x80213091
[   13.131976] [<801f4760>] 0x801f4760
[   13.135456] [<8021d3bc>] 0x8021d3bc
[   13.138943] [<8021dbe0>] 0x8021dbe0
[   13.142419] [<800a249c>] 0x800a249c
[   13.145907] [<8021de58>] 0x8021de58
[   13.149384] [<8021ddcc>] 0x8021ddcc
[   13.152864] [<8021bc34>] 0x8021bc34
[   13.156346] [<803d1bb4>] 0x803d1bb4
[   13.159827] [<8004c944>] 0x8004c944
[   13.163314] [<8021d0b4>] 0x8021d0b4
[   13.166791] [<80040eb4>] 0x80040eb4
[   13.170282] [<833f9000>] 0x833f9000 [rt2800pci@82c5c000+0x1010]
[   13.176191] [<8021e49c>] 0x8021e49c
[   13.179687] [<833f9000>] 0x833f9000 [rt2800pci@82c5c000+0x1010]
[   13.185591] [<8000c88c>] 0x8000c88c
[   13.189078] [<8003e8c8>] 0x8003e8c8
[   13.192576] [<800779a0>] 0x800779a0
[   13.196041] [<800b8fe4>] 0x800b8fe4
[   13.199528] [<80078fec>] 0x80078fec
[   13.203005] [<80076fc8>] 0x80076fc8
[   13.206493] [<800b9540>] 0x800b9540
[   13.209965] [<800b9624>] 0x800b9624
[   13.213446] [<800794b4>] 0x800794b4
[   13.216934] [<8000482c>] 0x8000482c
[   13.220410] [<80006c58>] 0x80006c58
[   13.223890]
[   13.225364]
Code: 8fbf001c  10000002  27bd0020 <000c000d> 03e00008  00000000  14a00005  00000000  3c048044
[   13.235365] ---[ end trace 2c87884f5734b28d ]---
[   13.243256] Fatal exception: panic in 5 seconds
[   18.248581] Kernel panic - not syncing: Fatal exception
[   18.254456] Rebooting in 1 seconds..

How the heck do i get LEDE working on this modem?

anon57995562 · October 27, 2017, 5:34am

I would suggest running a checksum first...

https://lede-project.org/docs/guide-quick-start/verify_firmware_checksum

JEFFreal · October 27, 2017, 8:15am

The checksum is fine

JEFFreal · October 27, 2017, 8:39am

Installed a trunk and get also a kernel panic

tftpboot 0x80700000 lede-lantiq-xrx200-VGV7519NOR-squashfs-sysupgrade.bin
erase 0xB0080000 +${filesize}
cp.b 0x80700000 0xB0080000 ${filesize}
bootm 0xB0080000

Below you can find the log:

## Booting kernel from Legacy Image at b0080000 ...
   Image Name:   MIPS LEDE Linux-4.9.58
   Created:      2017-10-27   1:26:37 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1817450 Bytes = 1.7 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.58 (buildbot@builds) (gcc version 5.5.0 (LEDE GCC 5.5.0 r5145-5e425ad) ) #0 SMP Tue Oct 24 20:15:57 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV7519NOR - KPN Experiabox V8
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 03e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] percpu: Embedded 12 pages/cpu @8108d000 s17520 r8192 d23440 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15748
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00038080
[    0.000000] Readback ErrCtl register=00038080
[    0.000000] Memory: 55452K/63488K available (4300K kernel code, 175K rwdata, 1320K rodata, 1228K init, 243K bss, 8036K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007885] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042390] pid_max: default: 32768 minimum: 301
[    0.047270] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053808] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.064459] Brought up 1 CPUs
[    0.072521] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.082187] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.088421] pinctrl core: initialized pinctrl subsystem
[    0.095281] NET: Registered protocol family 16
[    0.105348] pinctrl-xway 1e100b10.pinmux: Init done
[    0.110988] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.221798] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.233659] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.239338]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.244589]   IO 0x000000001ae00000..0x000000001affffff
[    0.281577] gpio-stp-xway 1e100bb0.stp: Init done
[    0.286963] usbcore: registered new interface driver usbfs
[    0.292494] usbcore: registered new interface driver hub
[    0.297872] usbcore: registered new device driver usb
[    0.303272] PCI host bridge to bus 0000:00
[    0.307284] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.314199] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.321139] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.327994] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.336527] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.349859] clocksource: Switched to clocksource MIPS
[    0.356415] NET: Registered protocol family 2
[    0.361987] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.368895] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.375283] TCP: Hash tables configured (established 1024 bind 1024)
[    0.381830] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.387645] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.394252] NET: Registered protocol family 1
[    0.402073] gptu: totally 6 16-bit timers/counters
[    0.406945] gptu: misc_register on minor 63
[    0.411106] gptu: succeeded to request irq 126
[    0.415581] gptu: succeeded to request irq 127
[    0.420090] gptu: succeeded to request irq 128
[    0.424604] gptu: succeeded to request irq 129
[    0.429130] gptu: succeeded to request irq 130
[    0.433635] gptu: succeeded to request irq 131
[    0.441240] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.446588] lantiq,vmmc 1f103000.vmmc: requested GPIO 493
[    0.452028] lantiq,vmmc 1f103000.vmmc: requested GPIO 492
[    0.457469] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03b00000
[    0.463922] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.471220] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3AC0000
[    0.477581] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3AC0000
[    0.585450] genirq: Flags mismatch irq 0. 00000000 (RTLX) vs. 00000400 (IPI_resched)
[    0.594741] Crashlog allocated RAM at address 0x3d00000
[    0.606314] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.622689] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.628435] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.655182] io scheduler noop registered
[    0.659082] io scheduler deadline registered (default)
[    0.665025] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.673962] console [ttyLTQ0] enabled
[    0.673962] console [ttyLTQ0] enabled
[    0.681269] bootconsole [early0] disabled
[    0.681269] bootconsole [early0] disabled
[    0.690452] lantiq nor flash device: 00800000 at 10000000
[    0.694611] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.704031] Amd/Fujitsu Extended Query Table at 0x0040
[    0.709159]   Amd/Fujitsu Extended Query version 1.1.
[    0.714197] number of CFI chips: 1
[    0.717548] lantiq nor flash device: 00800000 at 14800000
[    0.723118] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.732590] Amd/Fujitsu Extended Query Table at 0x0040
[    0.737724]   Amd/Fujitsu Extended Query version 1.1.
[    0.742743] number of CFI chips: 1
[    0.746133] Concatenating MTD devices:
[    0.749872] (0): "ltq_nor"
[    0.752529] (1): "ltq_nor"
[    0.755266] into device "10000000.nor-boot"
[    0.759498] 4 ofpart partitions found on MTD device 10000000.nor-boot
[    0.765898] Creating 4 MTD partitions on "10000000.nor-boot":
[    0.771649] 0x000000040000-0x000000050000 : "board_config"
[    0.781294] 0x000000000000-0x000000040000 : "uboot"
[    0.787506] 0x000000060000-0x000000070000 : "uboot_env"
[    0.794216] 0x000000080000-0x000001000000 : "firmware"
[    0.821357] 2 uimage-fw partitions found on MTD device firmware
[    0.825979] 0x000000080000-0x00000023bbaa : "kernel"
[    0.832986] 0x00000023bbaa-0x000001000000 : "rootfs"
[    0.839111] mtd: device 5 (rootfs) set to be root filesystem
[    0.843516] 1 squashfs-split partitions found on MTD device rootfs
[    0.849573] 0x000000560000-0x000001000000 : "rootfs_data"
[    0.860043] libphy: Fixed MDIO Bus: probed
[    0.964783] libphy: lantiq,xrx200-mdio: probed
[    0.980094] net-xrx200: invalid MAC, using random
[    1.054353] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:00, irq=-1)
[    1.138329] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:01, irq=-1)
[    1.197688] random: fast init done
[    1.222313] Intel XWAY PHY11G (xRX integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX integrated)] (mii_bus:phy_addr=0:11, irq=-1)
[    1.306312] Intel XWAY PHY11G (xRX integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX integrated)] (mii_bus:phy_addr=0:13, irq=-1)
[    1.390329] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:05, irq=-1)
[    1.506544] ltq-cputemp cputemp@0: Current CPU die temperature: 40.5 Â°C
[    1.512130] wdt 1f8803f0.watchdog: Init done
[    1.519928] leds-gpio: probe of gpio-leds failed with error -5
[    1.525890] NET: Registered protocol family 10
[    1.538450] NET: Registered protocol family 17
[    1.541509] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.554490] 8021q: 802.1Q VLAN Support v1.8
[    1.570617] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.580561] Freeing unused kernel memory: 1228K
[    1.583689] This architecture does not have kernel memory protection.
[    2.346279] init: Console is alive
[    2.348577] init: - watchdog -
[    3.693207] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.840055] dwc2 1e101000.ifxhcd: requested GPIO 494
[    3.945490] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    3.949147] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    3.956456] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    3.961959] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    3.969368] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    3.977416] hub 1-0:1.0: USB hub found
[    3.980302] hub 1-0:1.0: 1 port detected
[    4.086049] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    4.089664] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    4.096974] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    4.102516] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.109929] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    4.117823] hub 2-0:1.0: USB hub found
[    4.120588] hub 2-0:1.0: 1 port detected
[    4.125851] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.142291] init: - preinit -
[    4.459162] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.395454] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    8.436081] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.639849] procd: - early -
[    8.641477] procd: - watchdog -
[    9.225773] lantiq,xrx200-net 1e108000.eth eth0: port 4 lost link
[    9.316681] procd: - watchdog -
[    9.319023] procd: - ubus -
[    9.524715] procd: - init -
Please press Enter to activate this console.
[   10.035041] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.044312] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   10.060768] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   10.073816] NET: Registered protocol family 8
[   10.076727] NET: Registered protocol family 20
[   10.089224] PPP generic driver version 2.4.2
[   10.101233] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.131347] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG[   10.152486]
[   10.152486]
[   10.152486] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   10.160201]
[   10.160201] Predefined debug level: 3
[   10.172820] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0
[   10.179518] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c
[   10.200084] Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   10.207468] request_timer(2, 0x000001AE, 1)...[   10.211675] successful!
[   10.214579] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   10.225656] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.236271] Infineon Technologies DEU driver version 2.0.0
[   10.243029] IFX DEU DES initialized (multiblock).
[   10.247606] IFX DEU AES initialized (multiblock).
[   10.251820] IFX DEU ARC4 initialized (multiblock).
[   10.256258] IFX DEU SHA1 initialized.
[   10.259846] IFX DEU MD5 initialized.
[   10.263376] IFX DEU SHA1_HMAC initialized.
[   10.267490] IFX DEU MD5_HMAC initialized.
[   10.280058] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   10.341198] NET: Registered protocol family 24
[   10.369490] xt_time: kernel timezone is -0000
[   10.461606] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   10.466374] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[   10.473307] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   10.481064] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0xffff detected
[   10.489294] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[   10.496894] ------------[ cut here ]------------
[   10.501517] WARNING: CPU: 0 PID: 538 at mm/vmalloc.c:1494 release_firmware+0x64/0x1c0
[   10.509297] Trying to vfree() bad address (83363a00)
[   10.514246] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib rt2x00pci rt2x00mmio rt2x00lib pppoe nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug
[   10.584451] CPU: 0 PID: 538 Comm: kmodloader Not tainted 4.9.58 #0
[   10.590617] Stack : 00000000 00000000 806e804a 00000036 80448a84 00000000 00000000 806e0000
[   10.598970]         83a464cc 80591ca7 80523044 00000000 0000021a 806e3d84 0000000a 024000c0
[   10.607326]         8009a4b8 80071fd8 00000001 806e0000 80597e04 80597e08 80527c2c 8328fabc
[   10.615682]         00000003 800af288 0000000a 024000c0 8009a4b8 80590000 00000002 8328fa00
[   10.624038]         00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   10.632394]         ...
[   10.634833] Call Trace:
[   10.637286] [<80010780>] show_stack+0x54/0x88
[   10.641655] [<801f6024>] dump_stack+0xd4/0x110
[   10.646086] [<8002f6b0>] __warn+0xe4/0x118
[   10.650163] [<8002f714>] warn_slowpath_fmt+0x30/0x3c
[   10.655137] [<80272a3c>] release_firmware+0x64/0x1c0
[   10.660114] [<82c96f1c>] rt2x00lib_free_eeprom_file+0x18/0x2c [rt2x00lib]
[   10.666891] [<82c91dc4>] rt2x00lib_probe_dev+0x814/0x8b4 [rt2x00lib]
[   10.673237] [<82c822b8>] rt2x00pci_probe+0x26c/0x2e0 [rt2x00pci]
[   10.679241] [<80240de0>] pci_device_probe+0x78/0xe8
[   10.684131] [<8026aeac>] driver_probe_device+0x184/0x31c
[   10.689420] [<8026b0d0>] __driver_attach+0x8c/0xc4
[   10.694206] [<8026923c>] bus_for_each_dev+0x9c/0xac
[   10.699081] [<8026a470>] bus_add_driver+0xe8/0x200
[   10.703870] [<8026b848>] driver_register+0xa8/0xf8
[   10.708653] [<80002658>] do_one_initcall+0xdc/0x1a4
[   10.713532] [<800af5c8>] do_init_module+0x74/0x1dc
[   10.718318] [<8009d0f0>] load_module+0x1960/0x1de8
[   10.723102] [<8009d690>] SyS_init_module+0x118/0x168
[   10.728065] [<8001a218>] syscall_common+0x34/0x58
[   10.732854] ---[ end trace aae541e73265177f ]---
[   10.737437] Kernel bug detected[#1]:
[   10.740946] CPU: 0 PID: 538 Comm: kmodloader Tainted: G        W       4.9.58 #0
[   10.748338] task: 83a461c0 task.stack: 8328e000
[   10.752858] $ 0   : 00000000 00000000 81063220 00000001
[   10.758081] $ 4   : 00000000 000000ff 000002fb 82c98220
[   10.763303] $ 8   : 80590000 65373332 36353137 3766205d
[   10.768525] $12   : 08000000 ac000000 00000000 03bd0000
[   10.773748] $16   : 8321f540 ffffffed 8321f820 8321eba0
[   10.778970] $20   : 82d1a95c 80710000 0000000a 024000c0
[   10.784193] $24   : 00000003 24000000
[   10.789415] $28   : 8328e000 8328fba0 8009a4b8 82c96f1c
[   10.794638] Hi    : 00000000
[   10.797510] Lo    : 00000000
[   10.800412] epc   : 800f5828 kfree+0x78/0x1a4
[   10.804759] ra    : 82c96f1c rt2x00lib_free_eeprom_file+0x18/0x2c [rt2x00lib]
[   10.811872] Status: 1100ff03 KERNEL EXL IE
[   10.816052] Cause : 10800034 (ExcCode 0d)
[   10.820056] PrId  : 00019556 (MIPS 34Kc)
[   10.823969] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib rt2x00pci rt2x00mmio rt2x00lib pppoe nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug
[   10.894220] Process kmodloader (pid: 538, threadinfo=8328e000, task=83a461c0, tls=77925dec)
[   10.902567] Stack : ffffffe0 8328fbc0 8321f540 ffffffed 8321f540 82c91dc4 00000002 80235198
[   10.910922]         82c970d4 80260f44 00000000 82dea680 8328fbdc 82d806ec 838bd400 8321f540
[   10.919278]         02400000 8321eba0 82d1a95c 80710000 0000000a 024000c0 8009a4b8 82c822b8
[   10.927633]         0000000a 024000c0 8009a4b8 80167224 8058f0a0 80243091 82d1ac34 838bd400
[   10.935989]         838bd468 82d1ac00 82d1ac34 80240de0 82d1ac34 8026a748 82dea400 83898eb0
[   10.944345]         ...
[   10.946784] Call Trace:
[   10.949233] [<800f5828>] kfree+0x78/0x1a4
[   10.953252] [<82c96f1c>] rt2x00lib_free_eeprom_file+0x18/0x2c [rt2x00lib]
[   10.960042] [<82c91dc4>] rt2x00lib_probe_dev+0x814/0x8b4 [rt2x00lib]
[   10.966388] [<82c822b8>] rt2x00pci_probe+0x26c/0x2e0 [rt2x00pci]
[   10.972388] [<80240de0>] pci_device_probe+0x78/0xe8
[   10.977271] [<8026aeac>] driver_probe_device+0x184/0x31c
[   10.982571] [<8026b0d0>] __driver_attach+0x8c/0xc4
[   10.987357] [<8026923c>] bus_for_each_dev+0x9c/0xac
[   10.992232] [<8026a470>] bus_add_driver+0xe8/0x200
[   10.997020] [<8026b848>] driver_register+0xa8/0xf8
[   11.001804] [<80002658>] do_one_initcall+0xdc/0x1a4
[   11.006681] [<800af5c8>] do_init_module+0x74/0x1dc
[   11.011469] [<8009d0f0>] load_module+0x1960/0x1de8
[   11.016252] [<8009d690>] SyS_init_module+0x118/0x168
[   11.021216] [<8001a218>] syscall_common+0x34/0x58
[   11.025907] Code: 30630001  24030001  38630001 <00030336> 8c430000  7c630380  10600003  00000000  10000002
[   11.035650]
[   11.037245] ---[ end trace aae541e732651780 ]---
[   11.044754] Kernel panic - not syncing: Fatal exception
[   11.050166] Rebooting in 1 seconds..

Plonk34 · October 27, 2017, 12:02pm

The error looks like here:

rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"

This mtd seem do be non-exist or wrong.

erase 0xB0080000 +${filesize}

Overides not all old data
When i have correctly calculated them should

erase 0xB0080000 +0xF80000

delete from after uboot to the end.
But I can wrong do these steps only if you know how you can return.

you should use the newest u-boot from LEDE trunk possible that here are the board_config partition are inside.
https://downloads.lede-project.org/snapshots/targets/lantiq/xrx200/u-boot-vgv7519_nor/u-boot.bin

If this wont work you can make a Image without WIFI drivers:
Download and unpack the image builder

wget https://downloads.lede-project.org/snapshots/targets/lantiq/xrx200/lede-imagebuilder-lantiq-xrx200.Linux-x86_64.tar.xz
tar -xf lede-imagebuilder-lantiq-xrx200.Linux-x86_64.tar.xz
cd lede-imagebuilder-lantiq-xrx200.Linux-x86_64
make image PROFILE=VGV7519NOR PACKAGES="-kmod-rt2800-pci"

The Image are inside here:
lede-imagebuilder-lantiq-xrx200.Linux-x86_64/bin/targets/lantiq/xrx200/

JEFFreal · October 27, 2017, 12:27pm

I will try that...
The weird thing is openwrt boots fine

JEFFreal · October 27, 2017, 12:39pm

VGV7519 # erase 0xB0080000 +0xF80000
Error: end address (0xb0ffffff) not in flash!
Bad address format

Plonk34 · October 27, 2017, 1:10pm

Sorry It should be 0xe80000
but wait i have equal with
https://wiki.openwrt.org/toh/arcadyan/vgv7510kw22
and here are the board_config on the end of the image (look under Flash layout when using u-boot)

This section should normally never never delete and the right size here 0xe60000

Plonk34 · October 27, 2017, 1:10pm

did you have the original image ?

Plonk34 · October 27, 2017, 1:32pm

Sorry but
15872 KiB = 15872 * 1024 B = 16252928 B
and the HEX value from 16252928 is 0xF80000
what is wrong here ?

On the https://wiki.openwrt.org/toh/arcadyan/vgv7519
under Flash layout i can not see any board_config section
I guess the docu is totally wrong or obsolet

JEFFreal · October 28, 2017, 6:48am

I've still got the original image and use the recentest U-Boot, Below you can find a log of the working OpenWRT. But i want the recent LEDE ofcourse

U-Boot 2013.10-openwrt4 (Oct 25 2017 - 22:43:50) VGV7519

Board: Arcadyan VGV7519
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR
DRAM:  64 MiB
Flash: 16 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
## Booting kernel from Legacy Image at b0080000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.23
   Created:      2016-02-02  12:37:10 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1599144 Bytes = 1.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 12:00:00 CET 2016
[    0.000000] SoC: VR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV7519 - KPN Experiabox V8
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00078080
[    0.000000] Readback ErrCtl register=00078080
[    0.000000] Memory: 59868K/65536K available (3450K kernel code, 148K rwdata, 1028K rodata, 152K init, 206K bss, 5668K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.052000] NET: Registered protocol family 16
[    0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.176000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.180000]   IO 0x000000001ae00000..0x000000001affffff
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.236000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.240000] Switched to clocksource MIPS
[    0.244000] NET: Registered protocol family 2
[    0.248000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.256000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.264000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.268000] TCP: reno registered
[    0.272000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.276000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.284000] NET: Registered protocol family 1
[    0.288000] gptu: totally 6 16-bit timers/counters
[    0.296000] gptu: misc_register on minor 63
[    0.300000] gptu: succeeded to request irq 126
[    0.304000] gptu: succeeded to request irq 127
[    0.308000] gptu: succeeded to request irq 128
[    0.312000] gptu: succeeded to request irq 129
[    0.316000] gptu: succeeded to request irq 130
[    0.320000] gptu: succeeded to request irq 131
[    0.328000] ralink,eeprom ralink_eep: using RT2860.eeprom as eeprom
[    0.332000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.340000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3920000
[    0.348000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3920000
[    0.452000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.472000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.476000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.488000] msgmni has been set to 116
[    0.492000] io scheduler noop registered
[    0.496000] io scheduler deadline registered (default)
[    0.500000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.508000] console [ttyLTQ0] enabled
[    0.508000] console [ttyLTQ0] enabled
[    0.516000] bootconsole [early0] disabled
[    0.516000] bootconsole [early0] disabled
[    0.528000] lantiq nor flash device: 00800000 at 10000000
[    0.532000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.540000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.544000]   Amd/Fujitsu Extended Query version 1.1.
[    0.552000] number of CFI chips: 1
[    0.552000] lantiq nor flash device: 00800000 at 14800000
[    0.560000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.568000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.572000]   Amd/Fujitsu Extended Query version 1.1.
[    0.580000] number of CFI chips: 1
[    0.584000] Concatenating MTD devices:
[    0.584000] (0): "ltq_nor"
[    0.588000] (1): "ltq_nor"
[    0.592000] into device "10000000.nor-boot"
[    0.596000] 4 ofpart partitions found on MTD device 10000000.nor-boot
[    0.600000] Creating 4 MTD partitions on "10000000.nor-boot":
[    0.608000] 0x000000000000-0x000000040000 : "uboot"
[    0.612000] 0x000000040000-0x000000050000 : "board_config"
[    0.620000] 0x000000060000-0x000000070000 : "uboot_env"
[    0.624000] 0x000000080000-0x000001000000 : "firmware"
[    0.628000] Support for built-in firmware splitter will be removed, please use CONFIG_MTD_SPLIT_UIMAGE_FW
[    0.636000] 0x0000002066e8-0x000001000000 : "rootfs"
[    0.644000] mtd: device 4 (rootfs) set to be root filesystem
[    0.648000] 1 squashfs-split partitions found on MTD device rootfs
[    0.656000] 0x000000470000-0x000001000000 : "rootfs_data"
[    0.780000] libphy: lantiq,xrx200-mdio: probed
[    0.800000] net-xrx200: invalid MAC, using random
[    0.804000] eth0: attached PHY [Generic PHY] (phy_addr=0:00, irq=-1)
[    0.808000] eth0: attached PHY [Generic PHY] (phy_addr=0:01, irq=-1)
[    0.880000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.948000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.956000] net-xrx200: invalid MAC, using random
[    0.960000] eth1: attached PHY [Generic PHY] (phy_addr=0:05, irq=-1)
[    0.964000] wdt 1f8803f0.watchdog: Init done
[    0.972000] TCP: cubic registered
[    0.972000] NET: Registered protocol family 17
[    0.976000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.992000] Bridge firewalling registered
[    0.996000] 8021q: 802.1Q VLAN Support v1.8
[    1.000000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.012000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.020000] Freeing unused kernel memory: 152K (8048a000 - 804b0000)
[    2.224000] init: Console is alive
[    2.228000] init: - watchdog -
[    3.772000] dwc2 1e101000.ifxhcd: requested GPIO 488
[    4.632000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    4.632000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    4.640000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    4.648000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.648000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    4.660000] hub 1-0:1.0: USB hub found
[    4.664000] hub 1-0:1.0: 1 port detected
[    5.280000] init: - preinit -
[    5.544000] random: procd urandom read with 21 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.800000] jffs2: notice: (293) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.816000] mount_root: switching to jffs2 overlay
[    8.836000] procd: - early -
[    8.836000] procd: - watchdog -
[    9.488000] procd: - ubus -
[   10.500000] procd: - init -
Please press Enter to activate this console.
[   11.684000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   11.712000] NET: Registered protocol family 10
[   11.720000] NET: Registered protocol family 8
[   11.724000] NET: Registered protocol family 20
[   11.732000] PPP generic driver version 2.4.2
[   11.744000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.768000] MEI CPE Driver, Version 1.2.0

[   11.768000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   11.792000]
[   11.792000] Predefined debug level: 2
[   11.804000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   11.808000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   11.820000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.828000] Infineon Technologies DEU driver version 2.0.0
[   11.836000] IFX DEU DES initialized (multiblock).
[   11.840000] IFX DEU AES initialized (multiblock).
[   11.844000] IFX DEU ARC4 initialized (multiblock).
[   11.848000] IFX DEU SHA1 initialized.
[   11.852000] IFX DEU MD5 initialized.
[   11.856000] IFX DEU SHA1_HMAC initialized.
[   11.860000] IFX DEU MD5_HMAC initialized.
[   11.872000] nf_conntrack version 0.5.0 (937 buckets, 3748 max)
[   11.896000] NET: Registered protocol family 24
[   11.920000] xt_time: kernel timezone is -0000
[   11.960000] cfg80211: Calling CRDA to update world regulatory domain
[   11.980000] cfg80211: World regulatory domain updated:
[   11.980000] cfg80211:  DFS Master region: unset
[   11.988000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.996000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.004000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.012000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.020000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.032000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.040000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.048000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.056000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   12.168000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   12.172000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   12.176000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
[   12.188000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   12.196000] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0xffff detected
[   12.204000] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
ioctl ATM_SETESI: No such device
[   18.028000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   18.032000] ifxmips_ptm: PTM init succeed
[   19.900000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   19.916000] device ptm0.4 entered promiscuous mode
[   19.920000] device ptm0 entered promiscuous mode
[   19.952000] br-iptv: port 1(ptm0.4) entered forwarding state
[   19.956000] br-iptv: port 1(ptm0.4) entered forwarding state
[   19.960000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   19.988000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.024000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.044000] device eth0.4 entered promiscuous mode
[   20.048000] device eth0 entered promiscuous mode
[   20.080000] device eth0.1 entered promiscuous mode
[   20.092000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   20.148000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.164000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.280000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.380000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.512000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   20.544000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.056000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.304000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.320000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.372000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.388000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.504000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.552000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.592000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.608000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.628000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.672000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.708000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.724000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.928000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   21.960000] br-iptv: port 1(ptm0.4) entered forwarding state
[   22.224000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   22.544000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   24.752000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
[   24.772000] /home/buildbot/slave-local/lantiq_xrx200/build/build_dir/target-mips_34kc+dsp_uClibc-0.9.33.2/linux-lantiq_xrx200/ltq-ptm-vr9/ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime

JEFFreal · October 28, 2017, 7:09am

Tried to erase the sectors you said....

VGV7519 # erase 0xb0080000 +e60000
Error: end address (0xb0edffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 +d60000
Error: end address (0xb0ddffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 +c60000
Error: end address (0xb0cdffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 +b60000
Error: end address (0xb0bdffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 +a60000
Error: end address (0xb0adffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 +0xB4000000
Error: end address (0x6407ffff) not in flash!
Bad address format
VGV7519 # erase 0xb0080000 0xB4000000

........................................................................................................................ done
Erased 120 sectors
VGV7519 # cp.b 0x80700000 0xB0080000 ${filesize}
Copy to Flash... done
VGV7519 # bootm 0xB0080000
## Booting kernel from Legacy Image at b0080000 ...
   Image Name:   MIPS LEDE Linux-4.4.92
   Created:      2017-10-17  17:46:20 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1640565 Bytes = 1.6 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.4.92 (buildbot@debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3560-79f57e422d) ) #0 Tue Oct 17 17:46:20 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV7519NOR - KPN Experiabox V8
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 03e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15748
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00038080
[    0.000000] Readback ErrCtl register=00038080
[    0.000000] Memory: 56380K/63488K available (3923K kernel code, 161K rwdata, 884K rodata, 1224K init, 213K bss, 7108K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000010] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007858] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042316] pid_max: default: 32768 minimum: 301
[    0.047161] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053723] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067134] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.076775] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.082993] pinctrl core: initialized pinctrl subsystem
[    0.089563] NET: Registered protocol family 16
[    0.098931] pinctrl-xway 1e100b10.pinmux: Init done
[    0.104456] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.214574] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.220328] Can't analyze schedule() prologue at 80009078
[    0.234848] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.240483]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.245746]   IO 0x000000001ae00000..0x000000001affffff
[    0.265177] gpio-stp-xway 1e100bb0.stp: Init done
[    0.270464] usbcore: registered new interface driver usbfs
[    0.275957] usbcore: registered new interface driver hub
[    0.281336] usbcore: registered new device driver usb
[    0.286738] PCI host bridge to bus 0000:00
[    0.290736] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.297641] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.304584] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.311440] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.319950] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.327633] clocksource: Switched to clocksource MIPS
[    0.333884] NET: Registered protocol family 2
[    0.339204] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.346099] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.352470] TCP: Hash tables configured (established 1024 bind 1024)
[    0.358984] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.364829] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.371411] NET: Registered protocol family 1
[    0.382594] gptu: totally 6 16-bit timers/counters
[    0.387434] gptu: misc_register on minor 63
[    0.391531] gptu: succeeded to request irq 126
[    0.396019] gptu: succeeded to request irq 127
[    0.400531] gptu: succeeded to request irq 128
[    0.405044] gptu: succeeded to request irq 129
[    0.409558] gptu: succeeded to request irq 130
[    0.414072] gptu: succeeded to request irq 131
[    0.421775] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.427077] lantiq,vmmc 1f103000.vmmc: requested GPIO 493
[    0.432538] lantiq,vmmc 1f103000.vmmc: requested GPIO 492
[    0.437982] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[    0.444416] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.451738] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3980000
[    0.458058] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3980000
[    0.566409] Crashlog allocated RAM at address 0x3d00000
[    0.594246] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.599972] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.613789] io scheduler noop registered
[    0.617605] io scheduler deadline registered (default)
[    0.623477] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.632380] console [ttyLTQ0] enabled
[    0.632380] console [ttyLTQ0] enabled
[    0.639704] bootconsole [early0] disabled
[    0.639704] bootconsole [early0] disabled
[    0.648634] lantiq nor flash device: 00800000 at 10000000
[    0.652751] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.662186] Amd/Fujitsu Extended Query Table at 0x0040
[    0.667317]   Amd/Fujitsu Extended Query version 1.1.
[    0.672355] number of CFI chips: 1
[    0.675753] lantiq nor flash device: 00800000 at 14800000
[    0.681263] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.690735] Amd/Fujitsu Extended Query Table at 0x0040
[    0.695866]   Amd/Fujitsu Extended Query version 1.1.
[    0.700901] number of CFI chips: 1
[    0.704296] Concatenating MTD devices:
[    0.708035] (0): "ltq_nor"
[    0.710706] (1): "ltq_nor"
[    0.713427] into device "10000000.nor-boot"
[    0.717651] 4 ofpart partitions found on MTD device 10000000.nor-boot
[    0.724062] Creating 4 MTD partitions on "10000000.nor-boot":
[    0.729823] 0x000000040000-0x000000050000 : "board_config"
[    0.738790] 0x000000000000-0x000000040000 : "uboot"
[    0.744439] 0x000000060000-0x000000070000 : "uboot_env"
[    0.750388] 0x000000080000-0x000001000000 : "firmware"
[    0.776564] 2 uimage-fw partitions found on MTD device firmware
[    0.781078] 0x000000080000-0x0000002108b5 : "kernel"
[    0.787861] 0x0000002108b5-0x000001000000 : "rootfs"
[    0.793458] mtd: device 5 (rootfs) set to be root filesystem
[    0.797764] 1 squashfs-split partitions found on MTD device rootfs
[    0.803879] 0x000000590000-0x000001000000 : "rootfs_data"
[    0.914417] libphy: lantiq,xrx200-mdio: probed
[    0.926916] net-xrx200: invalid MAC, using random
[    0.992366] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    1.060339] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    1.128324] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.196323] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.264339] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.371650] ltq-cputemp cputemp@0: Current CPU die temperature: 45.5 Â°C
[    1.377198] wdt 1f8803f0.watchdog: Init done
[    1.385301] NET: Registered protocol family 10
[    1.395338] NET: Registered protocol family 17
[    1.398479] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.410989] 8021q: 802.1Q VLAN Support v1.8
[    1.426064] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.435806] Freeing unused kernel memory: 1224K
[    2.543193] init: Console is alive
[    2.545498] init: - watchdog -
[    3.877273] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.983972] dwc2 1e101000.ifxhcd: requested GPIO 494
[    4.039799] eth0: port 0 got link
[    4.843837] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    4.847436] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    4.854749] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    4.860277] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.867718] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    4.875230] hub 1-0:1.0: USB hub found
[    4.878182] hub 1-0:1.0: 1 port detected
[    5.739855] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    5.743452] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    5.750764] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    5.756292] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.763733] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    5.771254] hub 2-0:1.0: USB hub found
[    5.774163] hub 2-0:1.0: 1 port detected
[    5.778980] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.795302] init: - preinit -
[    6.630397] random: procd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.857035] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.868026] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.040618] procd: - early -
[   10.042226] procd: - watchdog -
[   10.139422] eth0: port 0 lost link
[   10.714870] procd: - watchdog -
[   10.717100] procd: - ubus -
[   10.813799] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.822510] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.830894] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.839406] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.848851] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.857326] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.866502] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.875481] random: ubusd: uninitialized urandom read (4 bytes read, 47 bits of entropy available)
[   10.884714] procd: - init -
Please press Enter to activate this console.
[   11.352388] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.360822] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   11.375612] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   11.387693] NET: Registered protocol family 8
[   11.390599] NET: Registered protocol family 20
[   11.401686] PPP generic driver version 2.4.2
[   11.412098] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.437028] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG

Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   11.459725]
[   11.459725] Predefined debug level: 3
[   11.472284] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   11.478913] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   11.497874] Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   11.505244] request_timer(2, 0x000001AE, 1)...successful!
[   11.510788] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   11.521566] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.530682] Infineon Technologies DEU driver version 2.0.0
[   11.536926] IFX DEU DES initialized (multiblock).
[   11.541231] IFX DEU AES initialized (multiblock).
[   11.545404] IFX DEU ARC4 initialized (multiblock).
[   11.549971] IFX DEU SHA1 initialized.
[   11.553568] IFX DEU MD5 initialized.
[   11.557204] IFX DEU SHA1_HMAC initialized.
[   11.561229] IFX DEU MD5_HMAC initialized.
[   11.572357] nf_conntrack version 0.5.0 (900 buckets, 3600 max)
[   11.597377] NET: Registered protocol family 24
[   11.620578] xt_time: kernel timezone is -0000
[   11.711269] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   11.716012] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[   11.722945] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   11.730727] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0xffff detected
[   11.738942] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[   11.746525] ------------[ cut here ]------------
[   11.751122] WARNING: CPU: 0 PID: 490 at mm/vmalloc.c:1460 0x80224e04()
[   11.757638] Trying to vfree() bad address (8323ba00)
[   11.762587] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   11.835162] CPU: 0 PID: 490 Comm: kmodloader Not tainted 4.4.92 #0
[   11.841361] Stack : 80616882 00000036 80616882 00000001 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          ...
[   11.876841] Call Trace:[<80017684>] 0x80017684
[   11.881322] [<80017684>] 0x80017684
[   11.884799] [<80224e04>] 0x80224e04
[   11.888286] [<8002de38>] 0x8002de38
[   11.891759] [<80224e04>] 0x80224e04
[   11.895216] [<8002de94>] 0x8002de94
[   11.898748] [<80224e04>] 0x80224e04
[   11.902237] [<82c7761c>] 0x82c7761c [rt2x00lib@82c70000+0x8cd0]
[   11.908148] [<82c71fc4>] 0x82c71fc4 [rt2x00lib@82c70000+0x8cd0]
[   11.914061] [<801ea408>] 0x801ea408
[   11.917548] [<8323926c>] 0x8323926c [rt2x00pci@83239000+0x620]
[   11.923361] [<80213091>] 0x80213091
[   11.926842] [<801f5544>] 0x801f5544
[   11.930323] [<8021e308>] 0x8021e308
[   11.933810] [<8021eb2c>] 0x8021eb2c
[   11.937286] [<800a27e4>] 0x800a27e4
[   11.940774] [<8021eda4>] 0x8021eda4
[   11.944251] [<8021ed18>] 0x8021ed18
[   11.947719] [<8021cb88>] 0x8021cb88
[   11.951178] [<803d3dd4>] 0x803d3dd4
[   11.954692] [<8004cb30>] 0x8004cb30
[   11.958189] [<8021e008>] 0x8021e008
[   11.961659] [<80041078>] 0x80041078
[   11.965150] [<83395000>] 0x83395000 [rt2800pci@8337b000+0xe50]
[   11.970970] [<8021f3e8>] 0x8021f3e8
[   11.974467] [<83395000>] 0x83395000 [rt2800pci@8337b000+0xe50]
[   11.980283] [<8000c8cc>] 0x8000c8cc
[   11.983760] [<8003ea8c>] 0x8003ea8c
[   11.987232] [<80077c14>] 0x80077c14
[   11.990733] [<800b93a8>] 0x800b93a8
[   11.994222] [<80079260>] 0x80079260
[   11.997699] [<8007723c>] 0x8007723c
[   12.001187] [<800b98c8>] 0x800b98c8
[   12.004658] [<800b99ac>] 0x800b99ac
[   12.008137] [<80079728>] 0x80079728
[   12.011593] [<8000486c>] 0x8000486c
[   12.015103] [<80006c98>] 0x80006c98
[   12.018578]
[   12.020052] ---[ end trace 54475e1c6976cd43 ]---
[   12.024673] Kernel bug detected[#1]:
[   12.028216] CPU: 0 PID: 490 Comm: kmodloader Tainted: G        W       4.4.92 #0
[   12.035609] task: 838e0508 ti: 83162000 task.ti: 83162000
[   12.040999] $ 0   : 00000000 80017684 81062de0 00000000
[   12.046221] $ 4   : 82c78cc0 000000ff 00000009 00000000
[   12.051444] $ 8   : 0000002d 00004bf0 00000000 00000000
[   12.056666] $12   : 000000ff 000000ff 00000000 00000000
[   12.061888] $16   : 83115460 804b8060 83115734 ffffffed
[   12.067111] $20   : 8337b9ac 80640000 0000000a 8043a5d4
[   12.072333] $24   : 00000003 00000000
[   12.077556] $28   : 83162000 83163b70 804d0000 82c7761c
[   12.082779] Hi    : 00000002
[   12.085651] Lo    : 00000008
[   12.088527] epc   : 800c1b88 0x800c1b88
[   12.092362] ra    : 82c7761c 0x82c7761c [rt2x00lib@82c70000+0x8cd0]
[   12.098620] Status: 1100fd03 KERNEL EXL IE
[   12.102800] Cause : 10800024 (ExcCode 09)
[   12.106803] PrId  : 00019556 (MIPS 34Kc)
[   12.110717] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   12.183316] Process kmodloader (pid: 490, threadinfo=83162000, task=838e0508, tls=77c0dd48)
[   12.191665] Stack : 00000000 83163b90 83115460 804b8060 83115460 82c71fc4 00000f20 83163ba0
          82c777d4 00000000 00000000 82c6b400 00000000 83163bf6 00000001 801ea408
          83114160 838b2800 838b2800 83115460 02400000 83114b40 8337b9ac 80640000
          0000000a 8043a5d4 804d0000 8323926c 0000000a 8043a5d4 804d0000 8337bc84
          838b2868 80213091 8337bc84 838b2868 838b2800 8337bc50 8337bc84 801f5544
          ...
[   12.227176] Call Trace:[<82c71fc4>] 0x82c71fc4 [rt2x00lib@82c70000+0x8cd0]
[   12.234071] [<801ea408>] 0x801ea408
[   12.237558] [<8323926c>] 0x8323926c [rt2x00pci@83239000+0x620]
[   12.243371] [<80213091>] 0x80213091
[   12.246853] [<801f5544>] 0x801f5544
[   12.250334] [<8021e308>] 0x8021e308
[   12.253820] [<8021eb2c>] 0x8021eb2c
[   12.257297] [<800a27e4>] 0x800a27e4
[   12.260784] [<8021eda4>] 0x8021eda4
[   12.264261] [<8021ed18>] 0x8021ed18
[   12.267741] [<8021cb88>] 0x8021cb88
[   12.271223] [<803d3dd4>] 0x803d3dd4
[   12.274705] [<8004cb30>] 0x8004cb30
[   12.278191] [<8021e008>] 0x8021e008
[   12.281668] [<80041078>] 0x80041078
[   12.285159] [<83395000>] 0x83395000 [rt2800pci@8337b000+0xe50]
[   12.290981] [<8021f3e8>] 0x8021f3e8
[   12.294477] [<83395000>] 0x83395000 [rt2800pci@8337b000+0xe50]
[   12.300294] [<8000c8cc>] 0x8000c8cc
[   12.303781] [<8003ea8c>] 0x8003ea8c
[   12.307278] [<80077c14>] 0x80077c14
[   12.310744] [<800b93a8>] 0x800b93a8
[   12.314231] [<80079260>] 0x80079260
[   12.317709] [<8007723c>] 0x8007723c
[   12.321196] [<800b98c8>] 0x800b98c8
[   12.324668] [<800b99ac>] 0x800b99ac
[   12.328149] [<80079728>] 0x80079728
[   12.331637] [<8000486c>] 0x8000486c
[   12.335113] [<80006c98>] 0x80006c98
[   12.338593]
[   12.340067]
Code: 8fbf001c  10000002  27bd0020 <000c000d> 03e00008  00000000  14a00005  00000000  3c048044
[   12.350071] ---[ end trace 54475e1c6976cd44 ]---
[   12.357982] Fatal exception: panic in 5 seconds
[   17.363672] Kernel panic - not syncing: Fatal exception
[   17.369567] Rebooting in 1 seconds..

Plonk34 · October 28, 2017, 9:33am

For deleting old data first

sysupgrade -n

or dont keep settings [x]
or a reset after installation should have the same effect
But at moment i thing it is not the reason

Plonk34 · October 28, 2017, 9:36am

I thing the anwser is inside target/linux/lantiq/dts/VGV7519NOR.dts
and target/linux/lantiq/dts/VGV7519.dtsi
from old and new source

target/linux/lantiq/dts/VGV7519.dtsi

	fpi@10000000 {
		localbus@0 {
			nor-boot@0 {
				compatible = "lantiq,nor";
				bank-width = <2>;
				reg = <0 0x0 0x800000>, <1 0x800000 0x800000>;
				#address-cells = <1>;
				#size-cells = <1>;

				partitions {
					compatible = "fixed-partitions";
					#address-cells = <1>;
					#size-cells = <1>;

					boardconfig: partition@40000 {
						label = "board_config";
						reg = <0x40000 0x10000>;
						read-only;
					};
				};
			};
		};

And i think the secret of "... not in flash!" message are that a really 2 x 8 MB Flash be used.
see

reg = <0 0x0 0x800000>, <1 0x800000 0x800000>;

you can equal with VGV7510KW22.dtsi (with 1x 16MB)

But i am not shure.
My problem is that i am Hobbyist not a Developer, I can equal and hack somthing inside the dts files but for example i can say what the meaning of fpi@10000000 are.
So I am shure that the develper from the mailinglist: https://lists.infradead.org/mailman/listinfo/lede-dev know the answer what must be changed that the WLAN will work.

But i will equal both in peace, but it need some days time.

Timeless · November 2, 2017, 8:52am

I'm also using the VGV7519, I tested this target during it's development in LEDE/OpenWRT. But had no problems going from OpenWRT to LEDE and so on. I was able to flash it trough sysupgrade.

I'm still running LEDE 17.01.0 so it would be nice if you could try that release as well? See if that works, because I'm running it on multiple VGV7519's and they all work just fine.

Another thing is that I also tested a Sitecom WLR-6000 which is not fully supported in LEDE and also had a kernel panic with the mediatek wireless drives but I moved that to a later time. Because it was not fully supported anyway. But since you are also having that same issue on a mediatek device maybe a recent commit could have damaged the support for these devices.

So long story short, could you give LEDE 17.01.0 a try?

JEFFreal · November 2, 2017, 9:52am

Did that, it don't work either.

Can you tell me what the board config is?
When i installed u-boot i erased the whole nor flash. Do you know if the board config from original firmware is used or it's flashed later on the device?

Timeless · November 2, 2017, 10:14am

Yeah it is, it's used to get the MAC address for example. see: https://github.com/lede-project/source/commit/28faa3f292a3ba417bab5d7327dd54a6a086a198

Why did you erase the entire flash?
this should have been sufficient:

VGV7519 # erase 0xB0080000 +${filesize}
................................................................. done
Erased 65 sectors
VGV7519 # cp.b 0x80700000 0xB0080000 ${filesize}
Copy to Flash... done
VGV7519 # reset

Just a note, this website has a really great howto for flashing a VGV7519: http://www.alfredklomp.com/technology/experia-v8/

JEFFreal · November 2, 2017, 11:10am

I used indeed that website but for u-boot install over serial i used https://wiki.openwrt.org/toh/arcadyan/vgv7519

On openwrt it says erase all so i did. Openwrt is by the way running fine, bit i want the recent lede.

I got a backup, do you know how to flash the board config from my backup to the device?

Plonk34 · November 2, 2017, 12:37pm

The reason is at my experiens on VGV7510KW22 was that i get some strange errors when i do not.
The reason i thing was that some data from the old image make trouble but it was never ended in reboot loop and i can remove it by pressing the reset button.
Now i use always sysupgrade -n FILENAME

On the VGV7510KW22 is at the end of flash a board_config section that should not override.
But i thing it totally differ from the VGV7519

After eqal the OpenWRT log and LEDE log i thing

is wrong, because the same error are in the working OpenWRT image.
I thing the real error is here:

@JEFFreal can you post the output from 17.01.0
@all can everybody confirm that 17.01.4 is running on VGV7519 ?

exist more them once Hardwareversions from this device ?

JEFFreal · November 2, 2017, 8:01pm

17.01.0 also didn't work for me. See log below..
But I found the original board config on my pc. It's 64kb like it should be...
On OpenWRT wiki I rode it's stored from 0xB0040000 to 0xB0050000
I will give that a try, but what would be the right erase and write command for it?

U-Boot 2013.10-openwrt4 (Oct 25 2017 - 22:43:50) VGV7519

Board: Arcadyan VGV7519
SoC:   Lantiq VRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR
DRAM:  64 MiB
Flash: 16 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
## Booting kernel from Legacy Image at b0080000 ...
   Image Name:   MIPS LEDE Linux-4.4.50
   Created:      2017-02-20  17:13:44 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1638203 Bytes = 1.6 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is VGV7519NOR - KPN Experiabox V8
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 03e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003dfffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15748
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00038080
[    0.000000] Readback ErrCtl register=00038080
[    0.000000] Memory: 56380K/63488K available (3914K kernel code, 161K rwdata, 884K rodata, 1232K init, 213K bss, 7108K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000010] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007856] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042325] pid_max: default: 32768 minimum: 301
[    0.047167] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053731] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067165] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.076862] pinctrl core: initialized pinctrl subsystem
[    0.083388] NET: Registered protocol family 16
[    0.092792] pinctrl-xway 1e100b10.pinmux: Init done
[    0.098322] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.208496] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.223576] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.229220]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.234474]   IO 0x000000001ae00000..0x000000001affffff
[    0.254089] gpio-stp-xway 1e100bb0.stp: Init done
[    0.259381] usbcore: registered new interface driver usbfs
[    0.264894] usbcore: registered new interface driver hub
[    0.270234] usbcore: registered new device driver usb
[    0.275674] PCI host bridge to bus 0000:00
[    0.279666] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.286572] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.293517] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.300373] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.308877] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.316555] clocksource: Switched to clocksource MIPS
[    0.322871] NET: Registered protocol family 2
[    0.328180] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.335071] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.341450] TCP: Hash tables configured (established 1024 bind 1024)
[    0.347968] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.353802] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360364] NET: Registered protocol family 1
[    0.371609] gptu: totally 6 16-bit timers/counters
[    0.376446] gptu: misc_register on minor 63
[    0.380558] gptu: succeeded to request irq 126
[    0.385025] gptu: succeeded to request irq 127
[    0.389543] gptu: succeeded to request irq 128
[    0.394056] gptu: succeeded to request irq 129
[    0.398570] gptu: succeeded to request irq 130
[    0.403084] gptu: succeeded to request irq 131
[    0.410834] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.416138] lantiq,vmmc 1f103000.vmmc: requested GPIO 493
[    0.421600] lantiq,vmmc 1f103000.vmmc: requested GPIO 492
[    0.427045] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[    0.433477] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.440807] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 39A0000
[    0.447139] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 39A0000
[    0.555583] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.561645] Crashlog allocated RAM at address 0x3d00000
[    0.589275] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.594996] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.608846] io scheduler noop registered
[    0.612657] io scheduler deadline registered (default)
[    0.618520] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.627412] console [ttyLTQ0] enabled
[    0.627412] console [ttyLTQ0] enabled
[    0.634739] bootconsole [early0] disabled
[    0.634739] bootconsole [early0] disabled
[    0.643676] lantiq nor flash device: 00800000 at 10000000
[    0.647794] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.657231] Amd/Fujitsu Extended Query Table at 0x0040
[    0.662363]   Amd/Fujitsu Extended Query version 1.1.
[    0.667399] number of CFI chips: 1
[    0.670795] lantiq nor flash device: 00800000 at 14800000
[    0.676300] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.685778] Amd/Fujitsu Extended Query Table at 0x0040
[    0.690911]   Amd/Fujitsu Extended Query version 1.1.
[    0.695946] number of CFI chips: 1
[    0.699337] Concatenating MTD devices:
[    0.703080] (0): "ltq_nor"
[    0.705776] (1): "ltq_nor"
[    0.708449] into device "10000000.nor-boot"
[    0.712699] 4 ofpart partitions found on MTD device 10000000.nor-boot
[    0.719103] Creating 4 MTD partitions on "10000000.nor-boot":
[    0.724863] 0x000000040000-0x000000050000 : "board_config"
[    0.733897] 0x000000000000-0x000000040000 : "uboot"
[    0.739485] 0x000000060000-0x000000070000 : "uboot_env"
[    0.745519] 0x000000080000-0x000001000000 : "firmware"
[    0.771621] 2 uimage-fw partitions found on MTD device firmware
[    0.776139] 0x000000080000-0x00000020ff7b : "kernel"
[    0.782826] 0x00000020ff7b-0x000001000000 : "rootfs"
[    0.788444] mtd: device 5 (rootfs) set to be root filesystem
[    0.792754] 1 squashfs-split partitions found on MTD device rootfs
[    0.798869] 0x000000590000-0x000001000000 : "rootfs_data"
[    0.909549] libphy: lantiq,xrx200-mdio: probed
[    0.922018] net-xrx200: invalid MAC, using random
[    0.989289] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    1.057261] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    1.125246] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.193246] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.200935] net-xrx200: invalid MAC, using random
[    1.265272] eth1: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.372649] ltq-cputemp cputemp@0: Current CPU die temperature: 41.5 Â°C
[    1.378200] wdt 1f8803f0.watchdog: Init done
[    1.386309] NET: Registered protocol family 10
[    1.397062] NET: Registered protocol family 17
[    1.400136] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.412732] 8021q: 802.1Q VLAN Support v1.8
[    1.427636] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.437439] Freeing unused kernel memory: 1232K (804dc000 - 80610000)
[    2.580673] init: Console is alive
[    2.582922] init: - watchdog -
[    4.046407] dwc2 1e101000.ifxhcd: requested GPIO 494
[    4.076710] eth0: port 0 got link
[    4.904757] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    4.908353] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    4.915676] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    4.921196] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.928633] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    4.936075] hub 1-0:1.0: USB hub found
[    4.939055] hub 1-0:1.0: 1 port detected
[    5.800742] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    5.804353] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    5.811653] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    5.817180] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.824623] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    5.832071] hub 2-0:1.0: USB hub found
[    5.835052] hub 2-0:1.0: 1 port detected
[    5.841336] init: - preinit -
[    6.593009] random: procd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.811279] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    9.821977] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.050719] procd: - early -
[   10.052336] procd: - watchdog -
[   10.145936] eth0: port 0 lost link
[   10.722623] procd: - ubus -
[   10.818225] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.826938] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.835333] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.843828] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.853281] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.861750] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.870955] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.879934] random: ubusd: uninitialized urandom read (4 bytes read, 46 bits of entropy available)
[   10.889181] procd: - init -
Please press Enter to activate this console.
[   11.358217] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   11.372851] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   11.385020] NET: Registered protocol family 8
[   11.387938] NET: Registered protocol family 20
[   11.398907] PPP generic driver version 2.4.2
[   11.409334] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.434264] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG

Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   11.456859]
[   11.456859] Predefined debug level: 3
[   11.469018] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[   11.475204] Backport generated by backports.git backports-20160324-9-g0e38f5c
[   11.494104] Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   11.501452] request_timer(2, 0x000001AE, 1)...successful!
[   11.507034] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   11.517859] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.527019] Infineon Technologies DEU driver version 2.0.0
[   11.533260] IFX DEU DES initialized (multiblock).
[   11.537576] IFX DEU AES initialized (multiblock).
[   11.541690] IFX DEU ARC4 initialized (multiblock).
[   11.546375] IFX DEU SHA1 initialized.
[   11.549911] IFX DEU MD5 initialized.
[   11.553519] IFX DEU SHA1_HMAC initialized.
[   11.557572] IFX DEU MD5_HMAC initialized.
[   11.568912] nf_conntrack version 0.5.0 (900 buckets, 3600 max)
[   11.594266] NET: Registered protocol family 24
[   11.617667] xt_time: kernel timezone is -0000
[   11.707680] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   11.712401] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[   11.719363] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[   11.727136] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0xffff detected
[   11.735354] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[   11.742934] ------------[ cut here ]------------
[   11.747546] WARNING: CPU: 0 PID: 492 at mm/vmalloc.c:1460 0x80223eb8()
[   11.754046] Trying to vfree() bad address (82c6b200)
[   11.758997] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   11.831572] CPU: 0 PID: 492 Comm: kmodloader Not tainted 4.4.50 #0
[   11.837773] Stack : 80616882 00000036 80616882 00000001 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
          ...
[   11.873251] Call Trace:[<80017660>] 0x80017660
[   11.877730] [<80017660>] 0x80017660
[   11.881198] [<80223eb8>] 0x80223eb8
[   11.884694] [<8002ddc0>] 0x8002ddc0
[   11.888144] [<80223eb8>] 0x80223eb8
[   11.891661] [<8002de1c>] 0x8002de1c
[   11.895159] [<80223eb8>] 0x80223eb8
[   11.898647] [<833175dc>] 0x833175dc [rt2x00lib@83310000+0x8c70]
[   11.904570] [<83311d90>] 0x83311d90 [rt2x00lib@83310000+0x8c70]
[   11.910471] [<801e95d8>] 0x801e95d8
[   11.913958] [<82c6a24c>] 0x82c6a24c [rt2x00pci@82c6a000+0x5c0]
[   11.919773] [<80213091>] 0x80213091
[   11.923254] [<801f4760>] 0x801f4760
[   11.926734] [<8021d3bc>] 0x8021d3bc
[   11.930221] [<8021dbe0>] 0x8021dbe0
[   11.933696] [<800a249c>] 0x800a249c
[   11.937173] [<8021de58>] 0x8021de58
[   11.940661] [<8021ddcc>] 0x8021ddcc
[   11.944106] [<8021bc34>] 0x8021bc34
[   11.947629] [<803d1bb4>] 0x803d1bb4
[   11.951106] [<8004c944>] 0x8004c944
[   11.954592] [<8021d0b4>] 0x8021d0b4
[   11.958068] [<80040eb4>] 0x80040eb4
[   11.961560] [<832ae000>] 0x832ae000 [rt2800pci@82c6e000+0x1010]
[   11.967468] [<8021e49c>] 0x8021e49c
[   11.970964] [<832ae000>] 0x832ae000 [rt2800pci@82c6e000+0x1010]
[   11.976868] [<8000c88c>] 0x8000c88c
[   11.980321] [<8003e8c8>] 0x8003e8c8
[   11.983854] [<800779a0>] 0x800779a0
[   11.987319] [<800b9020>] 0x800b9020
[   11.990806] [<80078fec>] 0x80078fec
[   11.994283] [<80076fc8>] 0x80076fc8
[   11.997771] [<800b9540>] 0x800b9540
[   12.001231] [<800b9624>] 0x800b9624
[   12.004720] [<800794b4>] 0x800794b4
[   12.008177] [<8000482c>] 0x8000482c
[   12.011686] [<80006c58>] 0x80006c58
[   12.015162]
[   12.016629] ---[ end trace 2a3fb41cf52b0fd7 ]---
[   12.021260] Kernel bug detected[#1]:
[   12.024799] CPU: 0 PID: 492 Comm: kmodloader Tainted: G        W       4.4.50 #0
[   12.032192] task: 83928508 ti: 83128000 task.ti: 83128000
[   12.037583] $ 0   : 00000000 80017660 81070460 00000000
[   12.042805] $ 4   : 83318c60 000000ff 00000009 00000000
[   12.048028] $ 8   : 0000002d 00004af0 00000000 00000000
[   12.053250] $12   : 000000fb 000000fb 00000000 00000000
[   12.058473] $16   : 83125460 804b6060 83125734 ffffffed
[   12.063695] $20   : 82c6eb6c 80640000 0000000a 804385c0
[   12.068917] $24   : 00000003 00000000
[   12.074140] $28   : 83128000 83129b70 804c0000 833175dc
[   12.079363] Hi    : 00000001
[   12.082235] Lo    : a8f5c296
[   12.085112] epc   : 800c1818 0x800c1818
[   12.088947] ra    : 833175dc 0x833175dc [rt2x00lib@83310000+0x8c70]
[   12.095204] Status: 1100fd03 KERNEL EXL IE
[   12.099384] Cause : 10800024 (ExcCode 09)
[   12.103388] PrId  : 00019556 (MIPS 34Kc)
[   12.107302] Modules linked in: rt2800pci(+) rt2800mmio rt2800lib iptable_nat rt2x00pci rt2x00mmio rt2x00lib pppoe nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT pppox ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack ltq_deu_vr9 iptable_mangle iptable_filter ip_tables drv_vmmc crc_itu_t crc_ccitt compat drv_dsl_cpe_api drv_mei_cpe ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables pppoatm ppp_generic slhc br2684 atm drv_tapi eeprom_93cx6 drv_ifxos dwc2 gpio_button_hotplug cryptomgr aead crypto_null
[   12.179901] Process kmodloader (pid: 492, threadinfo=83128000, task=83928508, tls=77077d48)
[   12.188249] Stack : 00000000 83129b90 83125460 804b6060 83125460 83311d90 00000f10 83129ba0
          83317794 00000000 00000000 83339d00 82c6eb6c 83129bf6 00000001 801e95d8
          83124160 838a6800 838a6800 83125460 02400000 83124b40 82c6eb6c 80640000
          0000000a 804385c0 804c0000 82c6a24c 0000000a 804385c0 804c0000 82c6ee54
          838a6868 80213091 82c6ee54 838a6868 838a6800 82c6ee20 82c6ee54 801f4760
          ...
[   12.223761] Call Trace:[<83311d90>] 0x83311d90 [rt2x00lib@83310000+0x8c70]
[   12.230655] [<801e95d8>] 0x801e95d8
[   12.234142] [<82c6a24c>] 0x82c6a24c [rt2x00pci@82c6a000+0x5c0]
[   12.239956] [<80213091>] 0x80213091
[   12.243437] [<801f4760>] 0x801f4760
[   12.246918] [<8021d3bc>] 0x8021d3bc
[   12.250405] [<8021dbe0>] 0x8021dbe0
[   12.253881] [<800a249c>] 0x800a249c
[   12.257369] [<8021de58>] 0x8021de58
[   12.260845] [<8021ddcc>] 0x8021ddcc
[   12.264326] [<8021bc34>] 0x8021bc34
[   12.267807] [<803d1bb4>] 0x803d1bb4
[   12.271289] [<8004c944>] 0x8004c944
[   12.274776] [<8021d0b4>] 0x8021d0b4
[   12.278253] [<80040eb4>] 0x80040eb4
[   12.281744] [<832ae000>] 0x832ae000 [rt2800pci@82c6e000+0x1010]
[   12.287653] [<8021e49c>] 0x8021e49c
[   12.291148] [<832ae000>] 0x832ae000 [rt2800pci@82c6e000+0x1010]
[   12.297053] [<8000c88c>] 0x8000c88c
[   12.300539] [<8003e8c8>] 0x8003e8c8
[   12.304037] [<800779a0>] 0x800779a0
[   12.307502] [<800b9020>] 0x800b9020
[   12.310989] [<80078fec>] 0x80078fec
[   12.314467] [<80076fc8>] 0x80076fc8
[   12.317954] [<800b9540>] 0x800b9540
[   12.321427] [<800b9624>] 0x800b9624
[   12.324907] [<800794b4>] 0x800794b4
[   12.328396] [<8000482c>] 0x8000482c
[   12.331871] [<80006c58>] 0x80006c58
[   12.335351]
[   12.336826]
Code: 8fbf001c  10000002  27bd0020 <000c000d> 03e00008  00000000  14a00005  00000000  3c048044
[   12.346826] ---[ end trace 2a3fb41cf52b0fd8 ]---
[   12.354716] Fatal exception: panic in 5 seconds
[   17.360591] Kernel panic - not syncing: Fatal exception
[   17.366447] Rebooting in 1 seconds..