I'm using the Xiaomi Redmi Router AC2100 with architecture：MediaTek MT7621 ver:1 eco:4 and OpenWrt 23.05.2 r23630-842932a63d everything seems to work well, but the TX power is limited to 7 dBm (5mW) for the 2.4GHz radio while the Xiaomi Redmi Router AC2100 with architecture：MediaTek MT7621 ver:1 eco:3 that I have can do 30dbm on 2.4GHz, I'm on Brazil were 30dbm is allowed.
When I first noticed the issue on version 22.03.0 and I upgrade all the devices to the 23.05.2 and reset the configuration, but the power is still limited.
Is this a bug or am I misunderstanding something?
Let me know, if any other log would help:
iw list (only 2.4GHz part):
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x1fe
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 2412 MHz [1] (7.0 dBm)
* 2417 MHz [2] (7.0 dBm)
* 2422 MHz [3] (7.0 dBm)
* 2427 MHz [4] (7.0 dBm)
* 2432 MHz [5] (7.0 dBm)
* 2437 MHz [6] (7.0 dBm)
* 2442 MHz [7] (7.0 dBm)
* 2447 MHz [8] (7.0 dBm)
* 2452 MHz [9] (7.0 dBm)
* 2457 MHz [10] (7.0 dBm)
* 2462 MHz [11] (7.0 dBm)
* 2467 MHz [12] (7.0 dBm)
* 2472 MHz [13] (7.0 dBm)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 4,
total <= 4, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
iw reg get:
global
country BR: DFS-FCC
(2400 - 2483 @ 40), (N/A, 30), (N/A)
(5150 - 5250 @ 80), (N/A, 27), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (N/A, 27), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (N/A, 27), (0 ms), DFS, AUTO-BW
(5725 - 5850 @ 80), (N/A, 30), (N/A), AUTO-BW
(5925 - 7125 @ 320), (N/A, 12), (N/A), NO-OUTDOOR, PASSIVE-SCAN
(57000 - 71000 @ 2160), (N/A, 40), (N/A)
Kernel Log:
[ 0.000000] Linux version 5.15.137 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23630-842932a63d) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Tue Nov 14 13:38:11 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:4
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Redmi Router AC2100
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14736 r8192 d22128 u45056
[ 0.000000] pcpu-alloc: s14736 r8192 d22128 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00004806
[ 0.000000] Readback ErrCtl register=00004806
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119296K/131072K available (7300K kernel code, 624K rwdata, 880K rodata, 1232K init, 226K bss, 11776K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008049] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066220] pid_max: default: 32768 minimum: 301
[ 0.071623] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.078836] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090380] rcu: Hierarchical SRCU implementation.
[ 0.095856] smp: Bringing up secondary CPUs ...
[ 0.101250] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101277] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.101292] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101336] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160631] Synchronize counters for CPU 1: done.
[ 0.193158] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.193180] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.193192] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.193218] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.252120] Synchronize counters for CPU 2: done.
[ 0.282760] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282782] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.282793] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282825] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.337305] Synchronize counters for CPU 3: done.
[ 0.367161] smp: Brought up 1 node, 4 CPUs
[ 0.376377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.386179] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.393253] pinctrl core: initialized pinctrl subsystem
[ 0.400045] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.406653] thermal_sys: Registered thermal governor 'step_wise'
[ 0.412656] FPU Affinity set after 11720 emulations
[ 0.431421] clocksource: Switched to clocksource GIC
[ 0.437859] NET: Registered PF_INET protocol family
[ 0.442936] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.451050] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.459401] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.467080] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.474683] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.481692] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.488126] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.494617] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.501920] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.507550] PCI: CLS 0 bytes, default 32
[ 0.514350] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.526218] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.532066] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.543293] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.554533] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.560404] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.566447] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.572568] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.579241] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.588030] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.596140] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.961428] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 0.968324] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 0.973207] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.978017] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 0.985182] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 0.991482] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.996901] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.003756] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.009910] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.015860] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.022083] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.028330] pci 0000:00:00.0: supports D1
[ 1.032264] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.038866] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.044883] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.051060] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.057375] pci 0000:00:01.0: supports D1
[ 1.061293] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.068866] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.076849] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.085037] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 1.090987] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.097901] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.114024] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.119180] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.125274] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.131990] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.139140] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.146051] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 1.152056] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.158370] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.165786] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.170942] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.177040] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.183774] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.190912] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.197553] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.204117] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.210984] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.217576] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.224499] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.231201] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.238403] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.245149] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 1.252314] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 1.259026] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 1.265811] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.271842] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.277864] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.285165] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.290040] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.296119] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.302862] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.310005] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 1.316771] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.321710] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.327709] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.334482] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 1.344208] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.355462] printk: console [ttyS0] disabled
[ 1.359779] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.368821] printk: console [ttyS0] enabled
[ 1.377092] printk: bootconsole [early0] disabled
[ 1.389707] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xf1
[ 1.396149] nand: Toshiba NAND 128MiB 3,3V 8-bit
[ 1.400780] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.408361] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 1.415045] 10 fixed-partitions partitions found on MTD device mt7621-nand
[ 1.422497] Creating 10 MTD partitions on "mt7621-nand":
[ 1.427833] 0x000000000000-0x000000080000 : "Bootloader"
[ 1.439715] 0x000000080000-0x0000000c0000 : "Config"
[ 1.448414] 0x0000000c0000-0x000000100000 : "Bdata"
[ 1.456972] 0x000000100000-0x000000140000 : "factory"
[ 1.465872] 0x000000140000-0x000000180000 : "crash"
[ 1.474453] 0x000000180000-0x0000001c0000 : "crash_syslog"
[ 1.483917] 0x0000001c0000-0x000000200000 : "reserved0"
[ 1.491711] 0x000000200000-0x000000600000 : "kernel_stock"
[ 1.539915] 0x000000600000-0x000000a00000 : "kernel"
[ 1.587738] 0x000000a00000-0x000007f80000 : "ubi"
[ 2.955048] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.968863] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 2.980730] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
[ 2.990859] i2c_dev: i2c /dev entries driver
[ 2.998237] NET: Registered PF_INET6 protocol family
[ 3.005760] Segment Routing with IPv6
[ 3.009496] In-situ OAM (IOAM) with IPv6
[ 3.013606] NET: Registered PF_PACKET protocol family
[ 3.018744] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.032217] 8021q: 802.1Q VLAN Support v1.8
[ 3.042520] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.067480] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 3.075240] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.082849] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=23)
[ 3.095954] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=24)
[ 3.108772] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=25)
[ 3.121129] DSA: tree 0 setup
[ 3.127143] UBI: auto-attach mtd9
[ 3.130489] ubi0: attaching mtd9
[ 5.576374] ubi0: scanning is finished
[ 5.598117] ubi0: attached mtd9 (name "ubi", size 117 MiB)
[ 5.603694] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.610548] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.617328] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.624287] ubi0: good PEBs: 938, bad PEBs: 2, corrupted PEBs: 0
[ 5.630273] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.637483] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1662173734
[ 5.646605] ubi0: available PEBs: 0, total reserved PEBs: 938, PEBs reserved for bad PEB handling: 18
[ 5.655843] ubi0: background thread "ubi_bgt0d" started, PID 322
[ 5.658385] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.667413] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.683700] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.694978] Freeing unused kernel image (initmem) memory: 1232K
[ 5.700920] This architecture does not have kernel memory protection.
[ 5.707433] Run /sbin/init as init process
[ 5.711548] with arguments:
[ 5.711554] /sbin/init
[ 5.711560] with environment:
[ 5.711565] HOME=/
[ 5.711570] TERM=linux
[ 6.158062] init: Console is alive
[ 6.162147] init: - watchdog -
[ 7.268242] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.333860] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.350508] init: - preinit -
[ 8.350440] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.479910] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.523803] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.972601] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 8.985368] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.991907] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 9.001287] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.177364] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 11.183399] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 442
[ 11.267491] UBIFS (ubi0:1): recovery needed
[ 11.482560] UBIFS (ubi0:1): recovery completed
[ 11.487230] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.495072] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.504969] UBIFS (ubi0:1): FS size: 98152448 bytes (93 MiB, 773 LEBs), max 784 LEBs, journal size 4952064 bytes (4 MiB, 39 LEBs)
[ 11.516597] UBIFS (ubi0:1): reserved for root: 4635982 bytes (4527 KiB)
[ 11.523214] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4B3BE90E-22C1-41FC-BE57-BE49195AAB3D, small LPT model
[ 11.544214] mount_root: switching to ubifs overlay
[ 11.574059] urandom-seed: Seeding with /etc/urandom.seed
[ 11.702232] procd: - early -
[ 11.705361] procd: - watchdog -
[ 12.334132] procd: - watchdog -
[ 12.342120] procd: - ubus -
[ 12.438219] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.446960] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.458527] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.472443] procd: - init -
[ 13.393162] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.633184] zram: Added device: zram0
[ 13.642802] tun: Universal TUN/TAP device driver, 1.6
[ 13.715281] GACT probability on
[ 13.719927] Mirror/redirect action on
[ 13.733339] u32 classifier
[ 13.736075] input device check on
[ 13.739713] Actions configured
[ 13.769680] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 13.777275] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 13.883963] xt_time: kernel timezone is -0000
[ 14.098993] pci 0000:00:01.0: enabling device (0000 -> 0003)
[ 14.104735] mt7603e 0000:02:00.0: enabling device (0000 -> 0002)
[ 14.110984] mt7603e 0000:02:00.0: ASIC revision: 76030010
[ 14.574852] urngd: v1.0.2 started.
[ 15.134999] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[ 15.140599] mt7603e 0000:02:00.0: Build Time: 20160107100755
[ 15.167916] mt7603e 0000:02:00.0: firmware init done
[ 15.281459] random: crng init done
[ 15.284871] random: 29 urandom warning(s) missed due to ratelimiting
[ 15.352909] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.365168] pci 0000:00:00.0: enabling device (0000 -> 0003)
[ 15.370855] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 15.391543] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 15.391628] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag
[ 15.399240] PPP generic driver version 2.4.2
[ 15.405590] NET: Registered PF_PPPOX protocol family
[ 15.414708] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.564523] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 15.564523]
[ 15.858507] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 16.060416] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149
[ 17.532685] Unable to find swap-space signature
[ 23.642537] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 23.727014] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 23.735327] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 23.745156] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 23.752999] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.760342] br-lan: port 1(lan1) entered blocking state
[ 23.765709] br-lan: port 1(lan1) entered disabled state
[ 23.772637] device lan1 entered promiscuous mode
[ 23.777271] device eth0 entered promiscuous mode
[ 23.813455] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 23.823234] br-lan: port 2(lan2) entered blocking state
[ 23.828522] br-lan: port 2(lan2) entered disabled state
[ 23.837329] device lan2 entered promiscuous mode
[ 23.855639] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 23.864729] br-lan: port 3(lan3) entered blocking state
[ 23.869990] br-lan: port 3(lan3) entered disabled state
[ 23.878562] device lan3 entered promiscuous mode
[ 23.897862] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [MediaTek MT7530 PHY] (irq=POLL)
[ 23.907501] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
[ 23.922623] br-lan: port 4(wan) entered blocking state
[ 23.927813] br-lan: port 4(wan) entered disabled state
[ 23.934895] device wan entered promiscuous mode
[ 23.939903] br-lan: port 4(wan) entered blocking state
[ 23.945153] br-lan: port 4(wan) entered forwarding state
[ 23.953920] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 24.690670] br-lan: port 4(wan) entered disabled state
[ 26.541066] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 26.549233] br-lan: port 1(lan1) entered blocking state
[ 26.554577] br-lan: port 1(lan1) entered forwarding state
[ 27.294859] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 27.316508] br-lan: port 1(lan1) entered disabled state
[ 27.976779] br-lan: port 5(phy0-ap0) entered blocking state
[ 27.982463] br-lan: port 5(phy0-ap0) entered disabled state
[ 27.989461] device phy0-ap0 entered promiscuous mode
[ 27.995123] br-lan: port 5(phy0-ap0) entered blocking state
[ 28.000769] br-lan: port 5(phy0-ap0) entered forwarding state
[ 28.353880] br-lan: port 5(phy0-ap0) entered disabled state
[ 28.375747] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
[ 28.383085] br-lan: port 5(phy0-ap0) entered blocking state
[ 28.388777] br-lan: port 5(phy0-ap0) entered forwarding state
[ 30.038003] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 30.046115] br-lan: port 1(lan1) entered blocking state
[ 30.051505] br-lan: port 1(lan1) entered forwarding state
[ 50.992193] mt7530-mdio mdio-bus:1f lan1: Link is Down
[ 50.997472] br-lan: port 1(lan1) entered disabled state
[ 53.471591] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 53.479570] br-lan: port 3(lan3) entered blocking state
[ 53.484858] br-lan: port 3(lan3) entered forwarding state
[ 96.746626] mt7530-mdio mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 96.754669] br-lan: port 2(lan2) entered blocking state
[ 96.759924] br-lan: port 2(lan2) entered forwarding state
Any advice will be appreciated, openwrt has always worked well for me and I bought this router because I tested the eco:3 variant, I must be doing something wrong and I want to fix it.