Trying to connect ORICO M2PV-C3 M.2 NVMe Enclosure as usb device

Installing and Using OpenWrt
1

I'm trying to connect ORICO M2PV-C3 M.2 NVMe Enclosure as usb device but it's not getting detected, it's based on Realtek RTL9210

I think I've all required packages installed as usb core, uas, usb2, usb3, etc etc

It was never an issue with r7800 on hnyman build and readily detected without problems

Can someone help me to debug it?

@hnyman

BusyBox v1.36.1 (2023-09-04 13:29:35 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
root@OpenWrt:~# lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux 5.15.130 xhci-hcd xHCI Host Controller
Bus 001 Device 001: ID 1d6b:0002 Linux 5.15.130 xhci-hcd xHCI Host Controller
root@OpenWrt:~# lsusb -t
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/1p, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/2p, 480M
root@OpenWrt:~#
2

Mine's just a plain USB HDD, but here's what I've got on a 22.03.5 install:

$ opkg list-installed | grep usb
kmod-usb-core - 5.10.176-1
kmod-usb-ehci - 5.10.176-1
kmod-usb-storage - 5.10.176-1
kmod-usb-xhci-hcd - 5.10.176-1
kmod-usb2 - 5.10.176-1
kmod-usb3 - 5.10.176-1
libusb-1.0-0 - 1.0.24-5
usbutils - 014-1

$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux 5.10.176 xhci-hcd xHCI Host Controller
Bus 001 Device 002: ID 0480:0900 TOSHIBA EXTERNAL_USB
Bus 001 Device 001: ID 1d6b:0002 Linux 5.10.176 xhci-hcd xHCI Host Controller

$ lsusb -t
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/1p, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=, Driver=usb-storage, 480M
3

Thank you for prompt attention

Yes, yours look normal as your device can be seen by lsusb and lsusb -t

Here's my list of packages

root@OpenWrt:~# opkg list-installed | grep usb
kmod-usb-core - 5.15.127-1
kmod-usb-ehci - 5.15.127-1
kmod-usb-storage - 5.15.127-1
kmod-usb-storage-uas - 5.15.127-1
kmod-usb-xhci-hcd - 5.15.127-1
kmod-usb-xhci-mtk - 5.15.127-1
kmod-usb2 - 5.15.127-1
kmod-usb3 - 5.15.127-1
libusb-1.0-0 - 1.0.26-3
usbutils - 014-1
root@OpenWrt:~#

But i can't see it, device blinking led assures me secure physical connection, so something with RTL driver, by the way it's UASP supported and worked in UASP on hnyman r7800 build always , I'm clueless in this scenario, any help is highly appreciated

4

See this

BusyBox v1.36.1 (2023-08-19 14:01:06 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 23.05.0-rc3, r23389-5deed175a5
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:~# dmesg | grep usb
[    3.102248] usbcore: registered new interface driver usbfs
[    3.107782] usbcore: registered new interface driver hub
[    3.113161] usbcore: registered new device driver usb
[    3.123518] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[    3.128775] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1[    3.137866] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[    3.146976] xhci-mtk 1a0c0000.usb: irq 135, io mem 0x1a0c0000
[    3.152842] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[    3.158070] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2[    3.165482] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[    3.180497] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.880794] usbcore: registered new interface driver usb-storage
[    5.888889] usbcore: registered new interface driver uas
root@OpenWrt:~#

And

root@OpenWrt:~# lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux 5.15.127 xhci-hcd xHCI Host Controller
Bus 001 Device 001: ID 1d6b:0002 Linux 5.15.127 xhci-hcd xHCI Host Controller
root@OpenWrt:~# lsusb -t
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/1p, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/2p, 480M
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 2
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 5.15
S:  Manufacturer=Linux 5.15.127 xhci-hcd
S:  Product=xHCI Host Controller
S:  SerialNumber=1a0c0000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=5000 MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 3.00 Cls=09(hub  ) Sub=00 Prot=03 MxPS= 9 #Cfgs=  1
P:  Vendor=1d6b ProdID=0003 Rev= 5.15                                              S:  Manufacturer=Linux 5.15.127 xhci-hcd                                           S:  Product=xHCI Host Controller
S:  SerialNumber=1a0c0000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub                  E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms
root@OpenWrt:~#