Difference between good and bad boots:
$ diff bad.aw good2.aw -u
--- bad.aw 2024-10-13 21:30:32.737964193 +0300
+++ good2.aw 2024-10-13 21:34:16.510874733 +0300
@@ -19,8 +19,8 @@
Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
- Writing ErrCtl register=00001000
- Readback ErrCtl register=00001000
+ Writing ErrCtl register=00001006
+ Readback ErrCtl register=00001006
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 119216K/131072K available (7323K kernel code, 629K rwdata, 884K rodata, 1264K init, 225K bss, 11856K reserved, 0K cma-reserved)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
@@ -214,7 +214,7 @@
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
key and hit [enter
, [2
- jffs2: notice: (446) jffs2_build_xattr_subsystem: complete building xattr subsystem, 53 of xdatum (35 unchecked, 18 orphan) and 67 of xref (18 dead, 0 orphan) found.
+ jffs2: notice: (442) jffs2_build_xattr_subsystem: complete building xattr subsystem, 52 of xdatum (35 unchecked, 17 orphan) and 66 of xref (17 dead, 0 orphan) found.
mount_root: switching to jffs2 overlay
overlayfs: upper fs does not support tmpfile.
urandom-seed: Seeding with /etc/urandom.seed
@@ -236,8 +236,8 @@
mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20220929104113a
- urngd: v1.0.2 started.
mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20220929104145
+ urngd: v1.0.2 started.
mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20220929104205
mt7915e 0000:02:00.0: registering led 'mt76-phy0'
mt7915e 0000:02:00.0: registering led 'mt76-phy1'
@@ -270,3 +270,30 @@
br-lan: port 4(lan4) entered blocking state
br-lan: port 4(lan4) entered disabled state
device lan4 entered promiscuous mode
+ mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:04
+ mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
+ br-lan: port 5(phy0-ap0) entered blocking state
+ br-lan: port 5(phy0-ap0) entered disabled state
+ device phy0-ap0 entered promiscuous mode
+ br-lan: port 6(phy1-ap0) entered blocking state
+ br-lan: port 6(phy1-ap0) entered disabled state
+ device phy1-ap0 entered promiscuous mode
+ br-lan: port 6(phy1-ap0) entered blocking state
+ br-lan: port 6(phy1-ap0) entered forwarding state
+ IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
+ device phy1-ap0 left promiscuous mode
+ br-lan: port 6(phy1-ap0) entered disabled state
+ br-lan: port 6(phy1-ap0) entered blocking state
+ br-lan: port 6(phy1-ap0) entered disabled state
+ device phy1-ap0 entered promiscuous mode
+ br-lan: port 6(phy1-ap0) entered blocking state
+ br-lan: port 6(phy1-ap0) entered forwarding state
+ br-lan: port 6(phy1-ap0) entered disabled state
+ mtk_soc_eth 1e100000.ethernet wan: Link is Up - 1Gbps/Full - flow control off
+ IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
+ IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
+ br-lan: port 6(phy1-ap0) entered blocking state
+ br-lan: port 6(phy1-ap0) entered forwarding state
+ IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
+ br-lan: port 5(phy0-ap0) entered blocking state
+ br-lan: port 5(phy0-ap0) entered forwarding state