TP-Link 510 report

Dear friends,

I would like to report success in installing LEDE on TP-Link 510.
The TP-Link 510 is an outdoor device with built-i, PoE and two 100Mb ports.

This device is single band 5Ghz with a/n support.

iw list
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2261 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 2:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 5180 MHz [36] (20.0 dBm)
* 5200 MHz [40] (20.0 dBm)
* 5220 MHz [44] (20.0 dBm)
* 5240 MHz [48] (20.0 dBm)
* 5260 MHz [52] (17.0 dBm) (radar detection)
* 5280 MHz [56] (17.0 dBm) (radar detection)
* 5300 MHz [60] (17.0 dBm) (radar detection)
* 5320 MHz [64] (17.0 dBm) (radar detection)
* 5500 MHz [100] (17.0 dBm) (radar detection)
* 5520 MHz [104] (17.0 dBm) (radar detection)
* 5540 MHz [108] (17.0 dBm) (radar detection)
* 5560 MHz [112] (17.0 dBm) (radar detection)
* 5580 MHz [116] (17.0 dBm) (radar detection)
* 5600 MHz [120] (17.0 dBm) (radar detection)
* 5620 MHz [124] (17.0 dBm) (radar detection)
* 5640 MHz [128] (17.0 dBm) (radar detection)
* 5660 MHz [132] (17.0 dBm) (radar detection)
* 5680 MHz [136] (17.0 dBm) (radar detection)
* 5700 MHz [140] (17.0 dBm) (radar detection)
* 5745 MHz [149] (disabled)
* 5765 MHz [153] (disabled)
* 5785 MHz [157] (disabled)
* 5805 MHz [161] (disabled)
* 5825 MHz [165] (disabled)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }

   * #{ WDS } <= 2048,
     total <= 2048, #channels <= 1, STA/AP BI must match

HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing

It did not catch my eye, but the CPE-510 does not support ac wireless!