if boot success, this is the print:
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.188 (sdn@server64) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 SMP PREEMPT Sat Apr 16 12:59:34 2022
[ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: UniElec U7623-02 eMMC (512M RAM)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu s31500 r8192 d21748 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootfstype=squashfs,f2fs console=ttyS0,115200 block2mtd.block2mtd=/dev/mmcblk0p3,64KiB,factory blkdevparts=mmcblk0:3M@34M(recovery),7G@44M(root)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 508192K/524288K available (7168K kernel code, 226K rwdata, 1720K rodata, 1024K init, 242K bss, 16096K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x2f8/0x4b0 with crng_init=0
[ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 147020034397 ns
[ 0.000006] sched_clock: 32 bits at 13MHz, resolution 76ns, wraps every 165191050201ns
[ 0.000248] Calibrating delay loop... 2062.33 BogoMIPS (lpj=1031168)
[ 0.014055] pid_max: default: 32768 minimum: 301
[ 0.014217] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.014231] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.015092] CPU: Testing write buffer coherency: ok
[ 0.016106] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.016245] rcu: Hierarchical SRCU implementation.
[ 0.016699] smp: Bringing up secondary CPUs ...
[ 0.037614] smp: Brought up 1 node, 4 CPUs
[ 0.037632] SMP: Total of 4 processors activated (8290.30 BogoMIPS).
[ 0.037639] CPU: All CPU(s) started in SVC mode.
[ 0.044171] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3
[ 0.044558] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.044581] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.044761] pinctrl core: initialized pinctrl subsystem
[ 0.045815] NET: Registered protocol family 16
[ 0.046085] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.046983] No ATAGs?
[ 0.047136] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.047152] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.131463] usbcore: registered new interface driver usbfs
[ 0.131606] usbcore: registered new interface driver hub
[ 0.131665] usbcore: registered new device driver usb
[ 0.133173] clocksource: Switched to clocksource timer
[ 0.133505] Clockevents: could not switch to one-shot mode:
[ 0.133509] Clockevents: could not switch to one-shot mode:
[ 0.133512] Clockevents: could not switch to one-shot mode:
[ 0.133515] Clockevents: could not switch to one-shot mode:
[ 0.133520] dummy_timer is not functional.
[ 0.133527] dummy_timer is not functional.
[ 0.133529] dummy_timer is not functional.
[ 0.133532] Could not switch to high resolution mode on CPU 2
[ 0.133537] Could not switch to high resolution mode on CPU 3
[ 0.133539] Could not switch to high resolution mode on CPU 0
[ 0.133562] dummy_timer is not functional.
[ 0.133568] Could not switch to high resolution mode on CPU 1
[ 0.134064] thermal_sys: Registered thermal governor 'step_wise'
[ 0.134468] NET: Registered protocol family 2
[ 0.134671] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.135742] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.135780] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.135822] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.135882] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.135991] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.136023] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.136230] NET: Registered protocol family 1
[ 0.136267] PCI: CLS 0 bytes, default 64
[ 0.137137] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.138738] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.144783] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.144797] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.178766] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.195391] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.197934] printk: console [ttyS0] disabled
[ 0.218097] 11004000.serial: ttyS0 at MMIO 0x11004000 (irq = 198, base_baud = 1625000) is a ST16650V2
[ 0.584087] random: fast init done
[ 0.719526] printk: console [ttyS0] enabled
[ 0.724381] mtk_rng 1020f000.rng: registered RNG driver
[ 0.724614] crng init done
[ 0.734638] loop: module loaded
[ 0.738775] mt6323-regulator mt6323-regulator: Chip ID = 0x2023
[ 0.782066] mt7530 mdio-bus:00: MT7530 adapts as multi-chip module
[ 0.789169] mtk_soc_eth 1b100000.ethernet: generated random MAC address fa:49:21:25:94:60
[ 0.797942] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xe08e0000, irq 204
[ 0.808601] xhci-mtk 1a1c0000.usb: xHCI Host Controller
[ 0.813882] xhci-mtk 1a1c0000.usb: new USB bus registered, assigned bus number 1
[ 0.824692] xhci-mtk 1a1c0000.usb: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 0.833814] xhci-mtk 1a1c0000.usb: irq 202, io mem 0x1a1c0000
[ 0.840372] hub 1-0:1.0: USB hub found
[ 0.844199] hub 1-0:1.0: 1 port detected
[ 0.848517] xhci-mtk 1a1c0000.usb: xHCI Host Controller
[ 0.853780] xhci-mtk 1a1c0000.usb: new USB bus registered, assigned bus number 2
[ 0.861197] xhci-mtk 1a1c0000.usb: Host supports USB 3.0 SuperSpeed
[ 0.867563] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.876155] hub 2-0:1.0: USB hub found
[ 0.879960] hub 2-0:1.0: 1 port detected
[ 0.884531] i2c /dev entries driver
[ 0.888620] mtk-thermal 1100b000.thermal: Device not calibrated, using default calibration values
[ 0.898355] mtk-wdt 10007000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.906635] cpu cpu0: dummy supplies not allowed for exclusive requests
[ 0.914938] sdhci: Secure Digital Host Controller Interface driver
[ 0.921145] sdhci: Copyright(c) Pierre Ossman
[ 0.948857] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.957467] NET: Registered protocol family 10
[ 0.963076] Segment Routing with IPv6
[ 0.966892] NET: Registered protocol family 17
[ 0.971549] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.984799] 8021q: 802.1Q VLAN Support v1.8
[ 0.989221] ThumbEE CPU extension supported.
[ 0.993654] Registering SWP/SWPB emulation handler
[ 0.998797] registered taskstats version 1
[ 1.028792] mtk-pcie 1a140000.pcie: host bridge /pcie@1a140000 ranges:
[ 1.035361] mtk-pcie 1a140000.pcie: IO 0x1a160000..0x1a16ffff -> 0x1a160000
[ 1.042599] mtk-pcie 1a140000.pcie: MEM 0x60000000..0x6fffffff -> 0x60000000
[ 1.059077] mmc0: new high speed MMC card at address 0001
[ 1.065447] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 1.070812] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 1.077336] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 1.083396] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (249:0)
[ 1.090916] mmcblk0: p1(recovery) p2(root)
[ 1.153595] mtk-pcie 1a140000.pcie: Port0 link down
[ 1.189737] mtk-pcie 1a140000.pcie: PCI host bridge to bus 0000:00
[ 1.195937] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.201428] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x1a160000-0x1a16ffff])
[ 1.210909] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.217927] pci 0000:00:01.0: [14c3:0801] type 01 class 0x060400
[ 1.223971] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.230307] pci 0000:00:01.0: supports D1
[ 1.234322] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.240367] pci 0000:00:02.0: [14c3:0801] type 01 class 0x060400
[ 1.246408] pci 0000:00:02.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.252743] pci 0000:00:02.0: supports D1
[ 1.256757] pci 0000:00:02.0: PME# supported from D0 D1 D3hot
[ 1.264139] PCI: bus0: Fast back to back transfers disabled
[ 1.268615] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 1.269726] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.284245] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.292399] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.298459] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.305293] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.312099] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.319926] PCI: bus1: Fast back to back transfers disabled
[ 1.325512] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.332275] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 1.338323] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.344743] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.352556] PCI: bus2: Fast back to back transfers disabled
[ 1.358142] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.364786] pci 0000:00:01.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.371580] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.378805] pci 0000:00:02.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.385600] pci 0000:00:01.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.392396] pci 0000:00:02.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.399192] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.405754] hub 1-1:1.0: USB hub found
[ 1.406525] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 1.410532] hub 1-1:1.0: 3 ports detected
[ 1.417455] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.426421] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.433215] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.440449] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 1.447244] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.452224] pci 0000:00:02.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.459213] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[ 1.465471] pcieport 0000:00:01.0: PME: Signaling with IRQ 214
[ 1.471572] pcieport 0000:00:01.0: AER: enabled with IRQ 214
[ 1.477568] pcieport 0000:00:02.0: enabling device (0140 -> 0142)
[ 1.483816] pcieport 0000:00:02.0: PME: Signaling with IRQ 215
[ 1.489910] pcieport 0000:00:02.0: AER: enabled with IRQ 215
[ 1.495891] mt7530 mdio-bus:00: MT7530 adapts as multi-chip module
[ 1.529749] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-mtk
[ 1.552398] hub 2-1:1.0: USB hub found
[ 1.556477] hub 2-1:1.0: 3 ports detected
[ 1.659132] mt7530 mdio-bus:00 lan0 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 1.668245] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 1.677283] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 1.686333] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 1.695319] mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 1.704424] mt7530 mdio-bus:00: configuring for fixed/trgmii link mode
[ 1.714483] mt7530 mdio-bus:00: Link is Up - 1Gbps/Full - flow control off
[ 1.715077] DSA: tree 0 setup
[ 1.724801] block2mtd: too many arguments
[ 1.729021] hctosys: unable to open rtc device (rtc0)
[ 1.737385] VFS: Mounted root (squashfs filesystem) readonly on device 179:2.
[ 1.745439] Freeing unused kernel memory: 1024K
[ 1.750667] usb 1-1.2: new high-speed USB device number 3 using xhci-mtk
[ 1.757757] Run /sbin/init as init process
[ 1.966566] init: Console is alive
[ 1.970804] init: - watchdog -
[ 2.488404] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.519432] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.530868] SCSI subsystem initialized
[ 2.543018] ehci-fsl: Freescale EHCI Host controller driver
[ 2.549551] ehci-platform: EHCI generic platform driver
[ 2.556863] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.563946] ohci-platform: OHCI generic platform driver
[ 2.573913] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.585051] init: - preinit -
[ 3.082471] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/trgmii link mode
[ 3.090510] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.200590] device eth0 entered promiscuous mode
[ 3.205758] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
[ 3.212675] 8021q: adding VLAN 0 to HW filter on device lan1
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.655192] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce30d
[ 7.663245] mount_root: switching to f2fs overlay
[ 7.687572] insmod: module is already loaded - nls_cp437
[ 7.695932] insmod: module is already loaded - nls_iso8859-1
[ 7.704540] insmod: module is already loaded - fat
[ 7.712407] insmod: module is already loaded - vfat
[ 7.734492] urandom-seed: Seeding with /etc/urandom.seed
[ 7.821405] device eth0 left promiscuous mode
[ 7.831369] procd: - early -
[ 7.834356] procd: - watchdog -
Failed to connect to ubus
[ 8.390264] procd: - watchdog -
[ 8.394839] procd: - ubus -
[ 8.471082] procd: - init -
Please press Enter to activate this console.
[ 8.767891] urngd: v1.0.2 started.
[ 8.772398] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.796893] tun: Universal TUN/TAP device driver, 1.6
[ 8.844288] GACT probability on
[ 8.848484] Mirror/redirect action on
[ 8.860100] u32 classifier
[ 8.862909] input device check on
[ 8.867301] Actions configured
[ 8.903336] Simple TC action Loaded
[ 8.929136] usbcore: registered new interface driver cdc_wdm
[ 8.936422] Loading modules backported from Linux version v5.10.110-0-g3238bffaf992
[ 8.944116] Backport generated by backports.git v5.10.110-1-0-g1fbde860
[ 8.982907] usbcore: registered new interface driver usbserial_generic
[ 8.989639] usbserial: USB Serial support registered for generic
[ 9.039480] xt_time: kernel timezone is -0000
[ 9.049451] cdc_ether 1-1.2:1.0 usb0: register 'cdc_ether' at usb-1a1c0000.usb-1.2, CDC Ethernet Device, 02:0c:29:a3:9b:6d
[ 9.060753] usbcore: registered new interface driver cdc_ether
[ 9.068309] usbcore: registered new interface driver cdc_ncm
[ 9.096375] usbcore: registered new interface driver huawei_cdc_ncm
[ 9.165698] mt7603e 0000:02:00.0: enabling device (0140 -> 0142)
[ 9.171850] mt7603e 0000:02:00.0: ASIC revision: 76030010
[ 9.178595] mt7603e 0000:02:00.0: Invalid MAC address, using random address 8e:99:b2:fd:2e:9a
[ 9.771883] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[ 9.777553] mt7603e 0000:02:00.0: Build Time: 20160107100755
[ 9.807287] mt7603e 0000:02:00.0: firmware init done
[ 10.000373] mt76x2e 0000:01:00.0: enabling device (0140 -> 0142)
[ 10.006582] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[ 10.364431] mt76x2e 0000:01:00.0: Invalid MAC address, using random address 9e:26:e9:ed:51:c2
[ 10.413794] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[ 10.422859] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[ 10.428384] mt76x2e 0000:01:00.0: Build: 1
[ 10.432515] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[ 10.452491] mt76x2e 0000:01:00.0: Firmware running!
[ 10.465123] PPP generic driver version 2.4.2
[ 10.473884] NET: Registered protocol family 24
[ 10.482672] usbcore: registered new interface driver qmi_wwan
[ 10.490108] usbcore: registered new interface driver rndis_host
[ 10.499085] usbcore: registered new interface driver cdc_mbim
[ 10.506423] usbcore: registered new interface driver option
[ 10.512191] usbserial: USB Serial support registered for GSM modem (1-port)
[ 10.519482] option 1-1.2:1.2: GSM modem (1-port) converter detected
[ 10.526106] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
[ 10.533380] option 1-1.2:1.3: GSM modem (1-port) converter detected
[ 10.540048] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1
[ 10.550110] option 1-1.2:1.4: GSM modem (1-port) converter detected
[ 10.556745] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2
[ 10.565978] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 10.740735] /opt/aiwan/security.img: Can't open blockdev
crond[2118]: crond (busybox 1.33.2) started, log level 5
[ 14.200430] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 14.212082] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/trgmii link mode
[ 14.220243] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 14.229231] device eth0 entered promiscuous mode
[ 14.235277] mt7530 mdio-bus:00 lan0: configuring for phy/gmii link mode
[ 14.242804] 8021q: adding VLAN 0 to HW filter on device lan0
[ 14.251030] br-lan: port 1(lan0) entered blocking state
[ 14.256433] br-lan: port 1(lan0) entered disabled state
[ 14.262276] device lan0 entered promiscuous mode
[ 14.280560] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
[ 14.287702] 8021q: adding VLAN 0 to HW filter on device lan1
[ 14.296057] br-lan: port 2(lan1) entered blocking state
[ 14.301422] br-lan: port 2(lan1) entered disabled state
[ 14.307460] device lan1 entered promiscuous mode
[ 14.319584] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
[ 14.326677] 8021q: adding VLAN 0 to HW filter on device lan2
[ 14.335110] br-lan: port 3(lan2) entered blocking state
[ 14.340521] br-lan: port 3(lan2) entered disabled state
[ 14.346900] device lan2 entered promiscuous mode
[ 14.362483] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
[ 14.369477] 8021q: adding VLAN 0 to HW filter on device wan
[ 14.380130] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
[ 14.387283] 8021q: adding VLAN 0 to HW filter on device lan3
[ 15.005654] br-lan: port 4(wlan0) entered blocking state
[ 15.011073] br-lan: port 4(wlan0) entered disabled state
[ 15.017006] device wlan0 entered promiscuous mode
[ 15.022354] br-lan: port 4(wlan0) entered blocking state
[ 15.027722] br-lan: port 4(wlan0) entered forwarding state
[ 15.037503] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 15.051521] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.330326] br-lan: port 5(wlan1) entered blocking state
[ 15.336101] br-lan: port 5(wlan1) entered disabled state
[ 15.342958] device wlan1 entered promiscuous mode
[ 16.132061] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 16.139682] br-lan: port 5(wlan1) entered blocking state
[ 16.145057] br-lan: port 5(wlan1) entered forwarding state
[ 17.354385] mt7530 mdio-bus:00 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 17.362130] br-lan: port 1(lan0) entered blocking state
[ 17.367445] br-lan: port 1(lan0) entered forwarding state
[ 17.870595] 3g-wwan2: renamed from ppp0
[ 31.966022] vusb: disabling
[ 31.968853] vmc: disabling
[ 31.971583] vmch: disabling
[ 31.974447] vgp1: disabling
[ 31.977408] vcamaf: disabling