No that looks like contact points for some physical connector, like the RJ-45 jacks and the barrel jack on the same side.
This looks more like it - they seem to be labeled Tx / Rx / GND even (no VCC but usually you don't connect that).
Thanks. Sadly it's under the heat sink plate. I'm not sure if i can remove it and reattach later. But maybe it's possible to solder in from the other side. I ordered TTL module / cable and I have pin connectors so I guess we will find out if it works later.
I wish there was an easier way to test firmware safely or at least with some simple recovery option without serial port 
This is a vendor / manufacturer decision. UBoot supports remote network consoles however basically no manufacturer includes that support in their uboot builds.
If you build mainline uboot for your device you can include the remote console.
It appears Victure has released new firmware for this device.
Alas, it seemingly won't download the update and reports an error in classic Chinglish.
I think they didn't. The default firmware in this router requests upgrade information from this link "http://router.lb-link.cn/image/7621AC6_16M_128M/WR1200/70003128/upgrade.txt" (timeout)
It looks like the router is trying to check if there are available updates but can't.
https://www.lb-link.cn/download-detail.php?DId=49 - this could be the page with firmware updates (W1200, updated in 2017)
It's weird that there is no firmware or software support page on Victure website. I don't think that we should expect anything from them 
Still waiting for TTL adapter. Hopefully will arrive in a week or so.
1 Like
Thanks for the info. Maybe I just hadn't seen the Update button before in the the web control panel.
For what it's worth, I tried contacting Victure direct via email to ask about updates. To paraphrase, their reply was "nothing is broken so why would you do that?" I mentioned the security vulnerabilities and never got a reply.
I've been using the router now for a week or two as the main device in our household. A few days ago I had a worrying disconnect problem, where the router appeared to go offline although the LEDs on the front were still flashing. But the SSIDs could no longer be seen. Restarting it seemed to have fixed things.
I think Victure is a reseller who got a good deal on router boards and cases that they rebranded. Their website sells a hodgepodge of goods - they are not router specialists. None of the 5 networking products they sell have firmware upgrades.
1 Like
I have a Victure RX1800 WiFi 6 Router It looks like it has the same specs. I'm following your progress on this.
root@RX1800-2F17:~# cat /proc/cpuinfo
system type : MediaTek MT7621 ver:1 eco:3
machine : MediaTek MT7621 RFB (802.11ax,SNOR)
processor : 0
cpu model : MIPS 1004Kc V2.15
BogoMIPS : 586.13
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16 dsp mt
shadow register sets : 1
kscratch registers : 0
package : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available
VPE : 0
processor : 1
cpu model : MIPS 1004Kc V2.15
BogoMIPS : 586.13
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16 dsp mt
shadow register sets : 1
kscratch registers : 0
package : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available
VPE : 1
processor : 2
cpu model : MIPS 1004Kc V2.15
BogoMIPS : 586.13
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16 dsp mt
shadow register sets : 1
kscratch registers : 0
package : 0
core : 1
VCED exceptions : not available
VCEI exceptions : not available
VPE : 0
processor : 3
cpu model : MIPS 1004Kc V2.15
BogoMIPS : 586.13
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16 dsp mt
shadow register sets : 1
kscratch registers : 0
package : 0
core : 1
VCED exceptions : not available
VCEI exceptions : not available
VPE : 1
root@RX1800-2F17:~# lsmod
asix 17463 0
authenc 3419 1 crypto_hw_eip93
ax88179_178a 13232 0
bluetooth 288587 1 btmtk_uart
br_netfilter 13039 0
btmtk_uart 33582 0
crc_ccitt 1067 1 ppp_async
crc32c_generic 1328 0
crypto_hw_eip93 17607 0
des_generic 18411 1 crypto_hw_eip93
ebt_802_3 784 0
ebt_among 2576 0
ebt_limit 1312 0
ebt_mark 784 0
ebt_mark_m 688 0
ebt_pkttype 624 0
ebt_redirect 944 0
ebt_stp 2064 0
ebt_vlan 1008 0
ebtable_broute 848 0
ebtable_filter 976 0
ebtable_nat 976 0
ebtables 16117 3 ebtable_nat,ebtable_filter,ebtable_broute
ecb 1392 0
ehci_hcd 34583 1 ehci_platform
ehci_platform 4400 0
exfat 106107 0
ext4 358399 0
fat 51943 2 msdos,vfat
flow_manage 26633 0
fuse 76866 0
gpio_button_hotplug 6640 0
gre 1202 2 pptp,ip_gre
ip_gre 9813 0
ip_tables 10413 4 iptable_nat,iptable_mangle,iptable_filter
ip_tunnel 12206 1 ip_gre
ip6_tables 10177 32 ip6table_mangle,ip6table_filter
ip6_udp_tunnel 1751 1 l2tp_core
ip6t_REJECT 1040 2
ip6table_filter 688 1
ip6table_mangle 1200 1
ipt_MASQUERADE 720 1
ipt_REJECT 1008 2
iptable_filter 752 1
iptable_mangle 944 1
iptable_nat 816 1
jbd2 59778 1 ext4
l2tp_core 13852 2 l2tp_ppp,l2tp_netlink
l2tp_netlink 7816 1 l2tp_ppp
l2tp_ppp 14368 0
leds_gpio 3088 0
mapfilter 43974 0
mbcache 7469 0
mbcache2 3577 1 ext4
mii 3928 3 ax88179_178a,asix,usbnet
mmc_block 24881 0
mmc_core 88501 2 mmc_block,mt7621_sd
msdos 6640 0
mt7621_sd 11392 0
mtfwd 16673 1
mtkhnat 65421 0
nf_conntrack 58518 7 nf_nat_ipv4,nf_conntrack_ipv6,nf_conntrack_ipv4,xt_state,xt_conntrack,nf_nat_masquerade_ipv4,nf_nat
nf_conntrack_ipv4 5008 11
nf_conntrack_ipv6 5648 6
nf_defrag_ipv4 982 1 nf_conntrack_ipv4
nf_defrag_ipv6 5111 1 nf_conntrack_ipv6
nf_log_common 2767 2 nf_log_ipv4,nf_log_ipv6
nf_log_ipv4 3440 0
nf_log_ipv6 3920 0
nf_nat 9963 4 nf_nat_ipv4,xt_nat,nf_nat_redirect,nf_nat_masquerade_ipv4
nf_nat_ipv4 3889 1 iptable_nat
nf_nat_masquerade_ipv4 1564 1 ipt_MASQUERADE
nf_nat_redirect 1243 1 xt_REDIRECT
nf_reject_ipv4 2339 1 ipt_REJECT
nf_reject_ipv6 2760 1 ip6t_REJECT
nls_base 5424 8 vfat,fat,ntfs,nls_utf8,nls_iso8859_1,nls_cp437,exfat,usbcore
nls_cp437 4496 1
nls_iso8859_1 2960 0
nls_utf8 912 1
ntfs 95699 0
ohci_hcd 23551 1 ohci_platform
ohci_platform 3760 0
ppp_async 7072 0
ppp_generic 21666 10 pppoe,ppp_async,l2tp_ppp,pptp,pppox,ppp_mppe
ppp_mppe 5504 0
pppoe 8976 2
pppox 1434 3 pppoe,l2tp_ppp,pptp
pptp 14048 0
scsi_mod 93168 4 ums_cypress,sg,usb_storage,sd_mod
sd_mod 27360 2
sg 21632 0
sha1_generic 2165 0
slhc 5435 1 ppp_generic
ts_bm 1488 0
ts_fsm 2704 0
ts_kmp 1392 0
udp_tunnel 1955 1 l2tp_core
uhci_hcd 19168 0
ums_alauda 8912 0
ums_cypress 2704 0
ums_datafab 5008 0
ums_freecom 2320 0
ums_isd200 5984 0
ums_jumpshot 4144 0
ums_karma 1808 0
ums_sddr09 9472 0
ums_sddr55 6192 0
ums_usbat 8864 0
usb_common 2317 1 usbcore
usb_storage 40075 11 ums_usbat,ums_sddr55,ums_sddr09,ums_karma,ums_jumpshot,ums_isd200,ums_freecom,ums_datafab,ums_cypress,ums_alauda
usbcore 130806 24 ax88179_178a,asix,usbnet,usblp,ums_usbat,ums_sddr55,ums_sddr09,ums_karma,ums_jumpshot,ums_isd200,ums_freecom,ums_datafab,ums_cypress,ums_alauda,usb_storage,xhci_mtk,xhci_plat_hcd,xhci_pci,xhci_hcd,uhci_hcd,ohci_platform,ohci_hcd,ehci_platform,ehci_hcd
usblp 9232 0
usbnet 18731 2 ax88179_178a,asix
vfat 8720 1
x_tables 13060 33 ipt_REJECT,ipt_MASQUERADE,xt_time,xt_tcpudp,xt_string,xt_state,xt_nat,xt_multiport,xt_mark,xt_mac,xt_limit,xt_conntrack,xt_comment,xt_TCPMSS,xt_REDIRECT,xt_LOG,iptable_mangle,iptable_filter,ip_tables,ebtables,ebt_vlan,ebt_stp,ebt_redirect,ebt_pkttype,ebt_mark_m,ebt_mark,ebt_limit,ebt_among,ebt_802_3,ip6t_REJECT,ip6table_mangle,ip6table_filter,ip6_tables
xhci_hcd 95308 3 xhci_mtk,xhci_plat_hcd,xhci_pci
xhci_mtk 5520 0
xhci_pci 2672 0
xhci_plat_hcd 3568 0
xt_LOG 816 0
xt_REDIRECT 720 0
xt_TCPMSS 3024 4
xt_comment 560209
xt_conntrack 2448 16
xt_limit 1408 20
xt_mac 688 0
xt_mark 720 0
xt_multiport 1328 0
xt_nat 1200 48
xt_state 784 0
xt_string 784 0
xt_tcpudp 1840 57
xt_time 1872 0
root@RX1800-2F17:~#
Did anybody ever make progress with this?
I ask because we've been using the WR1200 for some time and it's pretty crap.
The 2.4GHz WiFi channel sometimes becomes unreliable – slow speed, timeouts. Meanwhile, 5GHz seems fine.
Rebooting the router fixes this but it's not ideal. Before I go out and buy a better brand, it'd be awesome if I could fix this with a newer version of OpenWRT.
Well, I was preparing to test the firmware using TTL right before the war broke out in the country. Even found a way to safely access pins. I'm not sure when I will be able to resume the work on this. Maybe someone will try to make it work before I can.
Sorry to hear this. Stay safe and good luck!
1 Like
I resumed the work on this. Successfully tested the build via TFTP (initramfs-kernel). Everything is working except WPS and 5G WIFI LED.
WPS is not working probably because of missing packages. I didn't really dig into it. Never used WPS option in my life
And about 5G LED I'm not sure. I'm missing something here. I tried to add "wlan5g" LED without much success. I also don't know how to retrieve GPIO information from source firmware (typical gpio paths are not available).
Overview:
mt7621_victure_wr1200.dts
#include "mt7621.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/ {
compatible = "victure,wr1200", "mediatek,mt7621-soc";
model = "Victure WR1200";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
label-mac-device = &gmac0;
};
chosen {
bootargs = "console=ttyS1,57600n8";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "green:power";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
wps {
label = "green:wps";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0x750000>;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
&gmac0 {
mtd-mac-address = <&factory 0x4>;
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan4";
};
port@1 {
status = "okay";
label = "lan3";
};
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan1";
};
port@4 {
status = "okay";
label = "wan";
mtd-mac-address = <&factory 0x4>;
mtd-mac-address-increment = <1>;
};
};
};
&state_default {
gpio {
groups = "wdt", "i2c", "jtag";
function = "gpio";
};
};
mt7621.mk
define Device/victure_wr1200
$(Device/dsa-migration)
IMAGE_SIZE := 6816k
DEVICE_VENDOR := Victure
DEVICE_MODEL := WR1200
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
endef
TARGET_DEVICES += victure_wr1200
I tried to flash sysupgrade through stock firmware interface. Serial console showed MD5 mismatch.
And if flashed via u-boot then serial console is showing this:
Image1 rootfs Checksum --> Invalid image Failed
Does anyone know what is causing this? Could this be some kind of firmware lock?
By the way, this is full version of original kernel log (from bootloader).
I noticed the unusual partitions layout in stock firmware. Maybe this is what I messed up with (like ignoring most of these partitions).
U-Boot 1.1.3 (Jun 4 2020 - 11:22:20)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fa0000
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: 16 MBytes NOR Flash
Date:Jun 4 2020 Time:11:22:20
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
##### The BUS freq = 220 MHZ ####
estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW
## Booting image at bc050000 ...
Erasing SPI Flash...
.
Writing to SPI Flash...
.
done
Image Name: MIPS OpenWrt-3.10.108
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1437406 Bytes = 1.4 MB
Load Address: 81001000
Entry Point: 81001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.108 (openwrt@blink.openwrt) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #19 SMP Wed Oct 28 18:38:39 CST 2020
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81530000 s6080 r8192 d14400 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=0007a6d5
[ 0.000000] Readback ErrCtl register=0007a6d5
[ 0.000000] Memory: 125536k/131072k available (3184k kernel code, 5536k reserved, 757k data, 212k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.120000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
[ 0.160000] pid_max: default: 32768 minimum: 301
[ 0.164000] Mount-cache hash table entries: 512
[ 0.168000] launch: starting cpu1
[ 0.172000] launch: cpu1 gone!
[ 0.172000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.172000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.172000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.172000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.204000] Synchronize counters for CPU 1: done.
[ 0.212000] launch: starting cpu2
[ 0.216000] launch: cpu2 gone!
[ 0.216000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.216000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.216000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.216000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.248000] Synchronize counters for CPU 2: done.
[ 0.256000] launch: starting cpu3
[ 0.260000] launch: cpu3 gone!
[ 0.260000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.260000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.260000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.260000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.288000] Synchronize counters for CPU 3: done.
[ 0.296000] Brought up 4 CPUs
[ 0.300000] NET: Registered protocol family 16
[ 0.600000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.604000] PCIE PHY initialize
[ 0.608000] ***** Xtal 40MHz *****
[ 0.612000] start MT7621 PCIe register access
[ 1.204000] RALINK_RSTCTRL = 7000000
[ 1.208000] RALINK_CLKCFG1 = 77ffeff8
[ 1.212000]
[ 1.212000] *************** MT7621 PCIe RC mode *************
[ 1.708000] PCIE2 no card, disable it(RST&CLK)
[ 1.712000] pcie_link status = 0x3
[ 1.716000] RALINK_RSTCTRL= 3000000
[ 1.720000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.724000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.728000] PCIE0 enabled
[ 1.732000] PCIE1 enabled
[ 1.736000] interrupt enable status: 300000
[ 1.740000] Port 1 N_FTS = 1b105000
[ 1.744000] Port 0 N_FTS = 1b105000
[ 1.748000] config reg done
[ 1.752000] init_rt2880pci done
[ 1.768000] bio: create slab <bio-0> at 0
[ 1.772000] PCI host bridge to bus 0000:00
[ 1.776000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.780000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.784000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.788000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.792000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.796000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.800000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.804000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
[ 1.808000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.812000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.816000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.820000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
[ 1.824000] pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
[ 1.828000] pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
[ 1.832000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.836000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref]
[ 1.840000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 1.844000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.848000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.852000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 1.856000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
...
[ 2.076000] Switching to clocksource MIPS
[ 2.080000] NET: Registered protocol family 2
[ 2.088000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.104000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.116000] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.128000] TCP: reno registered
[ 2.136000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.148000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.160000] NET: Registered protocol family 1
[ 2.172000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.184000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.204000] io scheduler noop registered (default)
[ 2.212000] reg_int_mask=0, INT_MASK= 0
[ 2.220000] HSDMA_init
[ 2.224000]
[ 2.224000] hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000
[ 2.244000]
[ 2.244000] hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
[ 2.260000] TX_CTX_IDX0 = 0
[ 2.264000] TX_DTX_IDX0 = 0
[ 2.272000] RX_CRX_IDX0 = 3ff
[ 2.276000] RX_DRX_IDX0 = 0
[ 2.280000] set_fe_HSDMA_glo_cfg
[ 2.288000] HSDMA_GLO_CFG = 465
[ 2.300000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.312000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.324000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.340000] Ralink gpio driver initialized
[ 2.348000] Enable Ralink GDMA Controller Module
[ 2.356000] GDMA IP Version=3
[ 2.364000] flash manufacture id: ef, device id 40 18
[ 2.372000] W25Q128BV(ef 40180000) (16384 Kbytes)
[ 2.384000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 2.404000] Creating 7 MTD partitions on "raspi":
[ 2.412000] 0x000000000000-0x000001000000 : "ALL"
[ 2.424000] 0x000000000000-0x000000030000 : "Bootloader"
[ 2.432000] 0x000000030000-0x000000040000 : "Config"
[ 2.444000] 0x000000040000-0x000000050000 : "Factory"
[ 2.456000] 0x000000050000-0x0000007a0000 : "firmware"
[ 2.468000] 0x0000001aef1e-0x0000007a0000 : "rootfs"
[ 2.476000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.504000] 0x0000007a0000-0x0000008b0000 : "rootfs_data"
[ 2.516000] 0x0000008b0000-0x000001000000 : "firmware2"
[ 2.528000] 0x000000a0ef1e-0x000001000000 : "rootfs2"
[ 2.536000] mtd: partition "rootfs2" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.564000] GMAC1_MAC_ADRH -- : 0x0000a09f
[ 2.572000] GMAC1_MAC_ADRL -- : 0x109000a5
[ 2.580000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 2.600000] GMAC1_MAC_ADRH -- : 0x0000a09f
[ 2.608000] GMAC1_MAC_ADRL -- : 0x109000a5
[ 2.616000] PROC INIT OK!
[ 2.620000] TCP: cubic registered
[ 2.628000] NET: Registered protocol family 10
[ 2.636000] NET: Registered protocol family 17
[ 2.648000] Bridge firewalling registered
[ 2.656000] 8021q: 802.1Q VLAN Support v1.8
[ 2.668000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.684000] Freeing unused kernel memory: 212K
[ 3.064000] init: Console is alive
[ 4.004000] usbcore: registered new interface driver usbfs
[ 4.016000] usbcore: registered new interface driver hub
[ 4.028000] usbcore: registered new device driver usb
[ 4.044000] SCSI subsystem initialized
[ 4.052000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.068000] ehci-platform: EHCI generic platform driver
[ 4.080000] usbcore: registered new interface driver usb-storage
[ 5.084000] init: - preinit -
[ 5.628000] Raeth v3.1 (Tasklet)
[ 5.636000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
[ 5.652000] phy_free_head is 0xc08000!!!
[ 5.660000] phy_free_tail_phy is 0xc09ff0!!!
[ 5.668000] txd_pool=a0c10000 phy_txd_pool=00C10000
[ 5.680000] ei_local->skb_free start address is 0x87e826e0.
[ 5.688000] free_txd: 00c10010, ei_local->cpu_ptr: 00C10000
[ 5.700000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 5.708000] ----------------+---------+--------
[ 5.720000] 0xa0c10000 0x00C10000 0x00C10000
[ 5.728000]
[ 5.728000] phy_qrx_ring = 0x00c0a000, qrx_ring = 0xa0c0a000
[ 5.744000]
[ 5.744000] phy_rx_ring0 = 0x00c0c000, rx_ring[0] = 0xa0c0c000
[ 5.780000] MT7530 Reset Completed!!
[ 5.792000] change HW-TRAP to 0x17c8f
[ 5.800000] set LAN/WAN LLLLW
[ 5.812000] GMAC1_MAC_ADRH -- : 0x0000a09f
[ 5.820000] GMAC1_MAC_ADRL -- : 0x109000a5
[ 5.828000] GDMA2_MAC_ADRH -- : 0x0000a09f
[ 5.836000] GDMA2_MAC_ADRL -- : 0x109000a6
[ 5.848000] eth1: ===> VirtualIF_open
[ 5.852000] MT7621 GE2 link rate to 1G
[ 5.868000] CDMA_CSG_CFG = 81000000
[ 5.876000] GDMA1_FWD_CFG = 20710000
[ 5.884000] GDMA2_FWD_CFG = 20710000
[ 5.892000] ethernet: port4 linkup(interrupt)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
mount_root.
emmc_partition_find(0x797008, rootfs_data)
(null) is not created by block2mtd, skip.
[ 9.148000] block: attempting to load /etc/config/fstab
[ 9.160000] block: unable to load configuration (fstab: Entry not found)
[ 9.176000] block: no usable configuration
jffs2 is ready
No jffs2 marker was found
[ 9.220000] jffs2: notice: (291) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[ 9.256000] block: attempting to load /etc/config/fstab
[ 9.264000] block: unable to load configuration (fstab: Entry not found)
[ 9.280000] block: no usable configuration
switching to overlay
[ 9.296000] ra2880stop()...Done
[ 9.304000] eth1: ===> VirtualIF_close
[ 9.312000] Free TX/RX Ring Memory!
[ 9.324000] procd: - early -
[ 9.956000] procd: - ubus -
[ 10.968000] procd: - init -
Please press Enter to activate this console.
[ 11.800000] l2tp_core: L2TP core driver, V2.0
[ 11.812000] l2tp_netlink: L2TP netlink interface
[ 11.820000] gre: GRE over IPv4 demultiplexor driver
[ 11.832000] ip_gre: GRE over IPv4 tunneling driver
[ 11.848000] fuse init (API version 7.22)
[ 11.860000] init ok
[ 11.864000] welcome to use this module! version=1.1.4 date=20191128 author=hyc
[ 12.436000] register rlt_drv
[ 12.452000] === pAd = c0801000, size = 2191792 ===
[ 12.468000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[ 12.480000] <-- RTMPAllocAdapterBlock, Status=0
[ 12.492000] pAd->CSRBaseAddress =0xc0700000, csr_addr=0xc0700000!
[ 12.504000] device_id =0x7603
[ 12.508000] RtmpChipOpsHook(474): Not support for HIF_MT yet!
[ 12.520000] mt7603_init()-->
[ 12.528000] mt_bcn_buf_init(224): Not support for HIF_MT yet!
[ 12.536000] <--mt7603_init()
[ 12.544000] load_dev_l1profile() ===== Fix me =====
[ 13.712000] register mt_drv
[ 13.732000] === pAd = c1381000, size = 4349760 ===
[ 13.752000] <-- RTMPAllocAdapterBlock, Status=0
[ 13.760000] pAd->PciHif.CSRBaseAddress =0xc1280000, csr_addr=0xc1280000!
[ 13.772000] RTMPInitPCIeDevice():device_id=0x7663
[ 13.784000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a01, pAd->ChipID=0x7663
[ 13.796000] mt7663_init()-->
[ 13.804000] <--mt7663_init()
[ 13.812000] <-- RTMPAllocTxRxRingMemory, Status=0
[ 13.820000] get_wdev_by_idx: invalid idx(0)
[ 13.884000] Ralink APSoC Hardware Watchdog Timer
[ 13.896000] rdm_major = 253
[ 13.920000] xt_time: kernel timezone is -0000
[ 13.940000] Ebtables v2.0 registered
[ 13.948000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.960000] Type=Restricted Cone
[ 13.976000] nf_conntrack version 0.5.0 (1964 buckets, 7856 max)
[ 14.000000] PPP generic driver version 2.4.2
[ 14.008000] PPP MPPE Compression module registered
[ 14.020000] NET: Registered protocol family 24
[ 14.032000] PPTP driver version 0.8.5
[ 14.052000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 15.252000] get_wdev_by_idx: invalid idx(0)
[ 15.280000] get_wdev_by_idx: invalid idx(0)
[ 15.696000] led=15, on=1, off=4000, blinks,=1, reset=1, time=4000
[ 15.708000] led=15, on=1, off=4000, blinks,=1, reset=1, time=4000
[ 15.768000] led=14, on=1, off=4000, blinks,=1, reset=1, time=4000
[ 15.780000] led=14, on=1, off=4000, blinks,=1, reset=1, time=4000
[ 15.792000] switch register base addr to system register 0xbe000000
[ 15.840000] write offset 0x60, value 0x405a8
[ 15.884000] led=14, on=1, off=4000, blinks,=1, reset=1, time=4000
[ 15.928000] led=15, on=4000, off=1, blinks,=1, reset=1, time=4000
[ 17.308000] get_wdev_by_idx: invalid idx(0)
[ 18.684000] 662 DHCP_Dns_fops_open
[ 18.692000] 669 DHCP_Dns_fops_write
[ 18.696000] buf: 0;0.0.0.0;00:00:00:00:00:00;myblink.cn
[ 18.696000]
[ 18.712000] 688 DHCP_Dns_fops_write
[ 19.208000] get_wdev_by_idx: invalid idx(0)
[ 20.140000] Raeth v3.1 (Tasklet)
[ 20.152000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
[ 20.164000] phy_free_head is 0xc5c000!!!
[ 20.172000] phy_free_tail_phy is 0xc5dff0!!!
[ 20.184000] txd_pool=a0c60000 phy_txd_pool=00C60000
[ 20.192000] ei_local->skb_free start address is 0x87e826e0.
[ 20.204000] free_txd: 00c60010, ei_local->cpu_ptr: 00C60000
[ 20.216000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 20.224000] ----------------+---------+--------
[ 20.228000] get_wdev_by_idx: invalid idx(0)
[ 20.240000] 0xa0c60000 0x00C60000 0x00C60000
[ 20.252000] phy_qrx_ring = 0x00c5e000, qrx_ring = 0xa0c5e000
[ 20.268000] phy_rx_ring0 = 0x00c68000, rx_ring[0] = 0xa0c68000
[ 20.308000] MT7530 Reset Completed!!
[ 20.320000] change HW-TRAP to 0x17c8f
[ 20.328000] set LAN/WAN LLLLW
[ 20.340000] GMAC1_MAC_ADRH -- : 0x0000a09f
[ 20.348000] GMAC1_MAC_ADRL -- : 0x109000a5
[ 20.356000] eth1: ===> VirtualIF_open
[ 20.364000] MT7621 GE2 link rate to 1G
[ 20.364000] CDMA_CSG_CFG = 81000000
[ 20.364000] GDMA1_FWD_CFG = 20710000
[ 20.364000] GDMA2_FWD_CFG = 20710000
[ 20.364000] device eth0 entered promiscuous mode
[ 20.404000] br-lan: port 1(eth0) entered listening state
[ 20.416000] br-lan: port 1(eth0) entered listening state
[ 20.424000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.444000] ethernet: port4 linkup(interrupt)
[ 20.452000] GDMA2_MAC_ADRH -- : 0x0000a09f
[ 20.452000] GDMA2_MAC_ADRL -- : 0x109000a6
[ 20.452000] eth1: ===> VirtualIF_open
[ 20.956000] get_wdev_by_idx: invalid idx(0)
[ 20.964000] get_wdev_by_idx: invalid idx(0)
[ 21.480000] load_dev_l1profile() ===== Fix me =====
[ 21.496000] E2pAccessMode=2
[ 21.500000] cfg_mode=9
[ 21.504000] cfg_mode=9
[ 21.512000] wmode_band_equal(): Band Equal!
...
[ 21.612000] default ApCliAPSDCapable[0]=1
...
[ 21.944000] AssocReqRssiThres = 0
[ 21.952000] KickStaRssiLow = 0
[ 21.956000] LedConfigMethod = 1
[ 21.964000] FW Version:CL173766_R
[ 21.972000] FW Build Date:20171110105932
[ 21.980000] CmdAddressLenReq:(ret = 0)
[ 21.988000] CmdFwStartReq: override = 1, address = 1048576
[ 22.000000] CmdStartDLRsp: WiFI FW Download Success
[ 22.020000] AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[ 22.028000] efuse_probe: efuse = 10000002
[ 22.036000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[ 22.048000] RtmpEepromGetDefault::e2p_dafault=1
[ 22.056000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[ 22.072000] NVM is FLASH mode, flash_offset = 0x0
[ 22.080000] 1. Phy Mode = 14
[ 22.088000] @@@ NICReadEEPROMParameters : pAd->FWLoad=0
[ 22.252000] Country Region from e2p = ffff
[ 22.264000] tssi_1_target_pwr_g_band = 33
[ 22.272000] 2. Phy Mode = 14
[ 22.276000] 3. Phy Mode = 14
[ 22.280000] NICInitPwrPinCfg(14): Not support for HIF_MT yet!
[ 22.292000] NICInitializeAsic(588): Not support rtmp_mac_sys_reset () for HIF_MT yet!
[ 22.308000] mt_mac_init()-->
[ 22.316000] mt7603_init_mac_cr()-->
[ 22.320000] AsicSetMacMaxLen(1907): Set the Max RxPktLen=1024!
[ 22.332000] <--mt_mac_init()
[ 22.340000] WTBL Segment 1 info:
[ 22.344000] MemBaseAddr/FID:0x28000/0
[ 22.352000] EntrySize/Cnt:32/128
[ 22.360000] WTBL Segment 2 info:
[ 22.368000] MemBaseAddr/FID:0x40000/0
[ 22.376000] EntrySize/Cnt:64/128
[ 22.380000] WTBL Segment 3 info:
[ 22.388000] MemBaseAddr/FID:0x42000/64
[ 22.396000] EntrySize/Cnt:64/128
[ 22.404000] WTBL Segment 4 info:
[ 22.408000] MemBaseAddr/FID:0x44000/128
[ 22.416000] EntrySize/Cnt:32/128
[ 22.424000] br-lan: port 1(eth0) entered learning state
[ 22.436000] AntCfgInit(2698): Not support for HIF_MT yet!
[ 22.444000] RTMPSetPhyMode(): channel out of range, use first ch=0
[ 22.456000] MCS Set = ff ff 00 00 01
...
[ 24.428000] br-lan: topology change detected, propagating
[ 24.436000] br-lan: port 1(eth0) entered forwarding state
...
...
...
[ 31.620000] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 5
[ 31.640000] Min Dirty = 336
[ 31.644000] ExChannel = 1 , 9
[ 31.648000] BW = 40
[ 31.656000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 31.784000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[ 31.796000] [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
[ 31.808000] [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
[ 31.820000] [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
[ 31.832000] AsicSetRalinkBurstMode(4322): Not support for HIF_MT yet!
[ 31.844000] RTMPSetPiggyBack(943): Not support for HIF_MT yet!
[ 31.868000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 31.880000] AsicSetTxPreamble(4309): Not support for HIF_MT yet!
[ 31.892000] AsicAddSharedKeyEntry(2073): Not support for HIF_MT yet!
[ 31.904000] The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
[ 31.920000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
[ 31.940000] <==== rt28xx_init, Status=0
[ 31.956000] @@@ ed_monitor_exit : ===>
[ 31.960000] @@@ ed_monitor_exit : <===
[ 31.968000] mt7603_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0x8564267c, EDCCA_Status=0
[ 31.984000] WiFi Startup Cost (ra0): 10.504s
[ 31.996000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 32.012000] Device Instance
...
[ 32.168000] The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
[ 32.184000] MTPciPollTxRxEmpty
[ 32.184000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 32.344000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 32.496000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 32.648000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 32.800000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 32.824000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
[ 32.836000] RTMPSetPiggyBack(943): Not support for HIF_MT yet!
[ 32.852000] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
[ 32.864000] RTMPDrvClose call RT28xxPciAsicRadioOff fail !!
[ 32.876000] tx_kickout_fail_count = 0
[ 32.884000] tx_timeout_fail_count = 0
[ 32.892000] rx_receive_fail_count = 0
[ 32.900000] alloc_cmd_msg = 115
[ 32.904000] free_cmd_msg = 115
[ 32.916000] Device Instance
...
[ 33.260000] device ra0 entered promiscuous mode
[ 33.544000] device ra1 entered promiscuous mode
[ 33.832000] device ra2 entered promiscuous mode
[ 34.124000] device ra3 entered promiscuous mode
[ 34.544000] load_dev_l1profile() ===== Fix me =====
[ 34.560000] E2pAccessMode=2
[ 34.568000] cfg_mode=9
[ 34.572000] cfg_mode=9
[ 34.576000] wmode_band_equal(): Band Equal!
...
[ 34.680000] default ApCliAPSDCapable[0]=1
...
[ 35.012000] AssocReqRssiThres = 0
[ 35.016000] KickStaRssiLow = 0
[ 35.024000] LedConfigMethod = 1
[ 35.032000] FW Version:CL173766_R
[ 35.036000] FW Build Date:20171110105932
[ 35.044000] AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[ 35.056000] efuse_probe: efuse = 10000002
[ 35.064000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[ 35.076000] RtmpEepromGetDefault::e2p_dafault=1
[ 35.084000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[ 35.100000] NVM is FLASH mode, flash_offset = 0x0
[ 35.108000] 1. Phy Mode = 14
[ 35.116000] @@@ NICReadEEPROMParameters : pAd->FWLoad=1
[ 35.124000] Country Region from e2p = ffff
[ 35.136000] tssi_1_target_pwr_g_band = 33
[ 35.144000] 2. Phy Mode = 14
[ 35.148000] 3. Phy Mode = 14
[ 35.152000] NICInitPwrPinCfg(14): Not support for HIF_MT yet!
[ 35.164000] NICInitializeAsic(588): Not support rtmp_mac_sys_reset () for HIF_MT yet!
[ 35.180000] mt_mac_init()-->
[ 35.188000] mt7603_init_mac_cr()-->
[ 35.192000] AsicSetMacMaxLen(1907): Set the Max RxPktLen=1024!
[ 35.204000] <--mt_mac_init()
[ 35.212000] WTBL Segment 1 info:
[ 35.216000] MemBaseAddr/FID:0x28000/0
[ 35.224000] EntrySize/Cnt:32/128
[ 35.232000] WTBL Segment 2 info:
[ 35.240000] MemBaseAddr/FID:0x40000/0
[ 35.248000] EntrySize/Cnt:64/128
[ 35.252000] WTBL Segment 3 info:
[ 35.260000] MemBaseAddr/FID:0x42000/64
[ 35.268000] EntrySize/Cnt:64/128
[ 35.276000] WTBL Segment 4 info:
[ 35.280000] MemBaseAddr/FID:0x44000/128
[ 35.288000] EntrySize/Cnt:32/128
[ 35.296000] AntCfgInit(2698): Not support for HIF_MT yet!
[ 35.308000] RTMPSetPhyMode(): channel out of range, use first ch=0
[ 35.320000] MCS Set = ff ff 00 00 01
...
...
...
...
...
[ 38.724000] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 5
[ 38.744000] Min Dirty = 152
[ 38.748000] ExChannel = 1 , 9
[ 38.752000] BW = 40
[ 38.760000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 38.888000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[ 38.900000] [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
[ 38.912000] [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
[ 38.924000] [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
[ 38.936000] AsicSetRalinkBurstMode(4322): Not support for HIF_MT yet!
[ 38.948000] RTMPSetPiggyBack(943): Not support for HIF_MT yet!
[ 38.972000] CmdSetTxPowerCtrl PwrPercentageDelta = 0
[ 38.984000] AsicSetTxPreamble(4309): Not support for HIF_MT yet!
[ 38.996000] AsicAddSharedKeyEntry(2073): Not support for HIF_MT yet!
[ 39.008000] The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
[ 39.024000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
[ 39.044000] <==== rt28xx_init, Status=0
[ 39.052000] @@@ ed_monitor_exit : ===>
[ 39.060000] @@@ ed_monitor_exit : <===
[ 39.068000] mt7603_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0x8564267c, EDCCA_Status=0
[ 39.084000] WiFi Startup Cost (ra0): 4.540s
[ 39.092000] br-lan: port 2(ra0) entered listening state
[ 39.104000] br-lan: port 2(ra0) entered listening state
[ 39.116000] get_wdev_by_idx: invalid idx(0)
[ 39.124000] get_wdev_by_idx: invalid idx(0)
[ 39.136000] get_wdev_by_idx: invalid idx(0)
[ 39.140000] get_wdev_by_idx: invalid idx(0)
[ 39.140000] get_wdev_by_idx: invalid idx(0)
[ 39.448000] get_wdev_by_idx: invalid idx(0)
[ 40.416000] The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8
[ 40.428000] MTPciPollTxRxEmpty
[ 41.044000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
[ 41.056000] RTMPSetPiggyBack(943): Not support for HIF_MT yet!
[ 41.072000] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
[ 41.084000] RTMPDrvClose call RT28xxPciAsicRadioOff fail !!
[ 41.096000] tx_kickout_fail_count = 0
[ 41.104000] tx_timeout_fail_count = 0
[ 41.108000] br-lan: port 2(ra0) entered learning state
[ 41.120000] rx_receive_fail_count = 0
[ 41.128000] alloc_cmd_msg = 69
[ 41.132000] free_cmd_msg = 69
I compiled a new Uboot for this device from the v2022.10-rc1 release candidate and installed it. Then I installed my own port of openwrt on the device. It works now somewhat. The only thing I could use some help with is the bootcmd. I'm using mtd read and bootm at the moment. If somebody needs it I can upload the .config of Uboot I used.
It will be nice if you upload u-boot .config
I could test it with my build later. And I'm sure it will be useful for anyone else who wants to flash openwrt onto this device.
By the way, is 5G LED working on your version of openwrt? I wasn't able to make it work back when I tested openwrt build.
So I lost my old .config file but i recreated it. I don't have the device with me for testing. When configuring and compiling uboot i recommend https://gitlab.com/openwrt-dev-ru-smartbox/u-boot-mt7621/-/blob/mt7621-v2018.09-rev1.3-2020-07-13/MTK%20MT7621%20U-Boot%20User%20Manual.pdf and https://u-boot.readthedocs.io/en/latest/board/mediatek/mt7621.html as a reference (remember the dram initialization blob). I used buildroot 2022.05 setup with gcc9 to crosscompile u-boot. I recommend having a flash programmer and a backup of stock firmware in case of failure. The Wifi Leds did not seem to work and i did not bother investigating. When building uboot make sure the binary fits in the 192k uboot partition.
config, image and my openwrt dts are in https://github.com/cd4046bf/Openwrt-for-Victure-AC1200-Files
I'm not good at configuring a bootloader, but it should work, maybe someone with a bit more knoledge can redo it better.
Pastebin?
Github?
WOW! thank you so much i was following this whole thread and it was actually working but i feel like i am missing a finishing step or something, how do i finish? please forgive my complete and utter ignorance, i am old and trying to learn, i have read the start guides and everything, obviously picking a router that is not supported officially may not have been the best move for a old newb, but i am here nonetheless. If you have any guidance i would be grateful.
This is great work! Well done all who put in the work. I would love to use it but like @skittles1200 above it's probably a little beyond my skills. Well, I probably could do install it, but I can't risk bricking the only router we have in the house.
The WR1200's existing firmware has a nasty bug that means, every month or so, the wifi breaks. We have to cold reboot the router. This happens mostly on the 5GHz channel but sometimes on the 2.4GHz channel too. It's just not very good software.
But ultimately I think we're just going to move on up to a Wifi6 router and send this WR1200 to the e-waste recycling centre in the sky...