He there,
First of all i will apologize in advance, this is my first post here.
I've been flashing various hardware with OpenWRT for quite some time including RG-EW1200 v1.x. All OK.
Recently i got my hands on the newer revision of the above model, v3.34.
i notice that that model fails to flash using the normal method. ( Login in the stock UI, loading the kernel image as firmware upgrade).
It hangs in that screen not going anything.
Connecting a UART serial adapter on the router i manage to boot it with the kernel OpenWRT image though TFTP. It seems to be booting just fine hardware wise.
My question/request now is, how can i flash the router permanently, the connect way though serial? Or help the community my adjusting a firmware to the newer revision?
below is the console out of my attempt.
If you need me to provide anything additional, im happy to do so.
Any help will be grandly appreciated.
Thanks
===================================================================
MT7621 stage1 code Aug 28 2018 16:58:15 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0x10, 1/0 = 676/348 41000000
PLL2 FB_DL: 0x13, 1/0 = 660/364 4D000000
PLL4 FB_DL: 0x14, 1/0 = 717/307 51000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1
000E:| 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1
000F:| 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
0011:| 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DRAMC_DQSCTL1[0e0]=13000000
DRAMC_DQSGCTL[124]=80000033
rank 0 coarse = 15
rank 0 fine = 56
B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0
opt_dle value:9
DRAMC_DDR2CTL[07c]=C287221D
DRAMC_PADCTL4[0e4]=000022B3
DRAMC_DQIDLY1[210]=0F0E0C0F
DRAMC_DQIDLY2[214]=0C0F0E0F
DRAMC_DQIDLY3[218]=0E0E0C0D
DRAMC_DQIDLY4[21c]=0D0D0D0B
DRAMC_R0DELDLY[018]=0000201F
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 15 11 13 15 15 12 15 11 13 10
10 | 13 13 11 11 11 12
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =31 DQS1 = 32
==================================================================
bit DQS0 bit DQS1
0 (1~61)31 8 (2~62)32
1 (1~59)30 9 (1~60)30
2 (1~60)30 10 (1~62)31
3 (1~61)31 11 (1~62)31
4 (1~61)31 12 (2~62)32
5 (0~59)29 13 (1~60)30
6 (0~60)30 14 (0~60)30
7 (0~60)30 15 (1~62)31
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 15 12 14 15 15 14 15 12 13 12
10 | 14 14 11 13 13 13
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
DRAMC_DQODLY1[200]=88888888
DRAMC_DQODLY2[204]=88888888
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=500000000 HZ BUS=166666666 HZ
===================================================================
U-Boot-1.1.3- (Sep 24 2024 - 16:00:21)
Board: Ralink APSoC DRAM: 128 MB
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
product info crc check success 9a805300
Erasing SPI Flash...
.
Writing to SPI Flash...
.
done
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Sep 24 2024 Time:16:00:21
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
#Reset_MT7530
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 4
0
#Reset_MT7530
4: System Enter Boot Command Line Interface.
U-Boot-1.1.3- (Sep 24 2024 - 16:00:21)
MT7621 # tftpboot
NetLoop,call eth_halt !
NetLoop,call eth_init !
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
*** Warning: no boot file name; using 'test.bin'
TFTP from server 192.168.64.1; our IP address is 192.168.64.3
Filename 'test.bin'.
=10,Load address: 0x82000000
Loading: checksum bad
checksum bad
Got ARP REPLY, set server/gtwy eth addr (48:65:ee:16:d2:fb)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 7944911 (793acf hex)
LoadAddr=82000000 NetBootFileXferSize= 00793acf
MT7621 # bootm
## Booting image at 82000000 ...
Image Name: MIPS OpenWrt Linux-6.12.74
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 7944847 Bytes = 7.6 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
OK
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 6.12.74 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r32802-f505120278) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Wed Mar 25 20:09:53 2026
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: legacy bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Ruijie RG-EW1200G PRO v.1.1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT
[ 0.000000] percpu: Embedded 13 pages/cpu s22896 r8192 d22160 u53248
[ 0.000000] Kernel command line: console=ttyS0,57600n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00038001
[ 0.000000] Readback ErrCtl register=00038001
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32768
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 256
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000005] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015986] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.088243] pid_max: default: 32768 minimum: 301
[ 0.107420] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.121838] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.147544] rcu: Hierarchical SRCU implementation.
[ 0.156948] rcu: Max phase no-delay instances is 1000.
[ 0.167854] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.184671] smp: Bringing up secondary CPUs ...
[ 0.194594] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.194631] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.194648] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.194697] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.256322] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.256350] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.256363] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.256395] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.316420] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.316448] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.316461] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.316497] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.375557] smp: Brought up 1 node, 4 CPUs
[ 0.535624] Memory: 111716K/131072K available (8750K kernel code, 653K rwdata, 1092K rodata, 5748K init, 236K bss, 18032K reserved, 0K cma-reserved)
[ 0.568178] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.587682] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.607053] pinctrl core: initialized pinctrl subsystem
[ 0.620378] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.632808] thermal_sys: Registered thermal governor 'step_wise'
[ 0.635277] /pinctrl: Fixed dependency cycle(s) with /pinctrl/pinctrl0
[ 0.660502] mt7621-pinctrl pinctrl: there is not valid maps for state default
[ 0.695238] clocksource: Switched to clocksource GIC
[ 0.714731] NET: Registered PF_INET protocol family
[ 0.724567] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.740510] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.757074] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.772430] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.787655] TCP bind hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.801865] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.815493] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.830129] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.843044] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.857917] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.869158] PCI: CLS 0 bytes, default 32
[ 0.880568] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.895868] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.907401] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.931803] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.404308] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.415941] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.427680] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.439508] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.452785] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.470239] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 1.486457] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.825246] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[ 1.839034] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.852837] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.862692] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.876896] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.889462] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.900306] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.913957] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.926314] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 PCIe Root Port
[ 1.940762] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x7fffffff]
[ 1.952506] pci 0000:00:00.0: BAR 1 [mem 0x00000000-0x0000ffff]
[ 1.964246] pci 0000:00:00.0: PCI bridge to [bus 00]
[ 1.974097] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.986190] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.999675] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 2.014086] pci 0000:00:00.0: supports D1
[ 2.021956] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.035346] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.051637] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 PCIe Endpoint
[ 2.065975] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit]
[ 2.078863] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 2.108747] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.119075] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.132233] pci 0000:00:00.0: BAR 0 [mem size 0x80000000]: can't assign; no space
[ 2.147042] pci 0000:00:00.0: BAR 0 [mem size 0x80000000]: failed to assign
[ 2.160908] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]: assigned
[ 2.175734] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]: assigned
[ 2.191559] pci 0000:00:00.0: BAR 1 [mem 0x60200000-0x6020ffff]: assigned
[ 2.205112] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]: assigned
[ 2.218590] pci 0000:01:00.0: BAR 0 [mem 0x60000000-0x600fffff 64bit]: assigned
[ 2.233059] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.242891] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.254995] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.268465] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.282816] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 2.300781] pci_bus 0000:00: resource 4 [mem 0x60000000-0x6fffffff]
[ 2.313225] pci_bus 0000:00: resource 5 [io 0x0000-0xffff]
[ 2.324275] pci_bus 0000:01: resource 0 [io 0x0000-0x0fff]
[ 2.335344] pci_bus 0000:01: resource 1 [mem 0x60000000-0x600fffff]
[ 2.347773] pci_bus 0000:01: resource 2 [mem 0x60100000-0x601fffff pref]
[ 2.363244] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.384325] printk: legacy console [ttyS0] disabled
[ 2.394847] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 2.412847] printk: legacy console [ttyS0] enabled
[ 2.412847] printk: legacy console [ttyS0] enabled
[ 2.431811] printk: legacy bootconsole [early0] disabled
[ 2.431811] printk: legacy bootconsole [early0] disabled
[ 2.565733] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 2.578195] 6 fixed-partitions partitions found on MTD device spi0.0
[ 2.591300] Creating 6 MTD partitions on "spi0.0":
[ 2.600902] 0x000000000000-0x000000050000 : "u-boot"
[ 2.612473] 0x000000050000-0x000000060000 : "u-boot-env"
[ 2.624391] 0x000000060000-0x000000070000 : "factory"
[ 2.636558] 0x000000070000-0x000000080000 : "product_info"
[ 2.648607] 0x000000080000-0x000000090000 : "kdump"
[ 2.659490] 0x000000090000-0x000001000000 : "firmware"
[ 2.670975] 2 uimage-fw partitions found on MTD device firmware
[ 2.682814] Creating 2 MTD partitions on "firmware":
[ 2.692718] 0x000000000000-0x0000002a7259 : "kernel"
[ 2.702616] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 2.720385] 0x0000002a7259-0x000000f70000 : "rootfs"
[ 2.730321] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 2.749784] mtd: setting mtd7 (rootfs) as root device
[ 2.759996] 1 squashfs-split partitions found on MTD device rootfs
[ 2.772342] 0x000000af0000-0x000000f70000 : "rootfs_data"
[ 2.906778] mtk_soc_eth 1e100000.ethernet: generated random MAC address 20:08:02:00:00:00
[ 2.924812] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.949058] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 2.967957] i2c_dev: i2c /dev entries driver
[ 2.981179] NET: Registered PF_INET6 protocol family
[ 2.995970] Segment Routing with IPv6
[ 3.003429] In-situ OAM (IOAM) with IPv6
[ 3.011440] NET: Registered PF_PACKET protocol family
[ 3.021629] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.048142] 8021q: 802.1Q VLAN Support v1.8
[ 3.094715] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 7.435393] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 7.451004] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 7.473679] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 7.477246] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 7.512046] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=23)
[ 7.535274] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=24)
[ 7.558139] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 7.571678] DSA: tree 0 setup
[ 7.578555] clk: Disabling unused clocks
[ 7.607877] Freeing unused kernel image (initmem) memory: 5748K
[ 7.619742] This architecture does not have kernel memory protection.
[ 7.632589] Run /init as init process
[ 8.208039] init: Console is alive
[ 8.215142] init: - watchdog -
[ 8.236054] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.252398] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 8.271071] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.293434] init: - preinit -
[ 11.995291] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
[ 12.582981] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 12.603554] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 12.617781] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 15.755281] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 16.943274] mt7530-mdio mdio-bus:1f lan3: Link is Down
[ 16.962977] procd: - early -
[ 16.969006] procd: - watchdog -
[ 17.552546] procd: - watchdog -
[ 17.559300] procd: - ubus -
[ 17.721240] procd: - init -
Please press Enter to activate this console.
[ 18.129431] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.156565] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized.
[ 18.731822] Loading modules backported from Linux version v6.18.7-0-g5dfbc5357
[ 18.746320] Backport generated by backports.git c8a37ce
[ 18.829338] pci 0000:00:00.0: enabling device (0000 -> 0003)
[ 18.840699] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 18.866713] mt7615e 0000:01:00.0: registering led 'mt76-phy0'
[ 18.969732] mt7615e 0000:01:00.0: registering led 'mt76-phy1'
[ 18.986186] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 18.986186]
[ 19.021089] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 19.058082] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149
[ 19.109250] PPP generic driver version 2.4.2
[ 19.121434] NET: Registered PF_PPPOX protocol family
[ 19.140018] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.427334] urngd: v1.0.2 started.
[ 51.495620] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 51.533347] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 51.549783] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 51.558988] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 51.584272] br-lan: port 1(lan3) entered blocking state
[ 51.594900] br-lan: port 1(lan3) entered disabled state
[ 51.605698] mt7530-mdio mdio-bus:1f lan3: entered allmulticast mode
[ 51.618402] mtk_soc_eth 1e100000.ethernet eth0: entered allmulticast mode
[ 51.635757] mt7530-mdio mdio-bus:1f lan3: entered promiscuous mode
[ 51.671549] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 51.687154] br-lan: port 2(lan2) entered blocking state
[ 51.697770] br-lan: port 2(lan2) entered disabled state
[ 51.708485] mt7530-mdio mdio-bus:1f lan2: entered allmulticast mode
[ 51.723720] mt7530-mdio mdio-bus:1f lan2: entered promiscuous mode
[ 51.742999] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 51.759448] br-lan: port 3(lan1) entered blocking state
[ 51.770373] br-lan: port 3(lan1) entered disabled state
[ 51.781077] mt7530-mdio mdio-bus:1f lan1: entered allmulticast mode
[ 51.796032] mt7530-mdio mdio-bus:1f lan1: entered promiscuous mode
[ 51.833674] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 54.549698] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 54.549868] br-lan: port 1(lan3) entered blocking state
[ 54.576040] br-lan: port 1(lan3) entered forwarding state
CTRL-A Z for help | 57600 8N1 | NOR | Minicom 2.9 | VT102 | Offline | ttyUSB0