Support for Huawei AX3 Pro

I have the -30 too in Mexico but version still in (c500) it it says it is already updated to last version

Answering myself (see my previous reply) I twisted their arm eventually and the device was replaced under warranty and indeed with the new one the WiFi doesn't slow down after a few days (I have now 10+ days of uptime). Still something seems off, like top speeds a little under what I had before (still in hundreds Mbps, I'm fine with that) and it seems like moderate transfers 50-100Mbps are breaking (few Mbps) streaming on other machine which didn't happen before but I'll blame for now two machines which I moved from Windows to Linux and it seems that the WiFi 5 support kind of sucks.

The board of your version is the same one as the chinese one, in other words, the one that has the amplifiers as you can see here:

This is a picture of the chinese board, and the number on your board and this one are the same = AM1WS7200M

Here you can see the amplifiers themselves:

2.4 Ghz =

5 Ghz =

The boards that dont have the amplifiers have different board number like this one:

Which is AM1WS720020M and as you can see in the picture there are no amplifiers for the 2.4 ghz.

So, are you sure there are no amplifiers in the router you got? How did you test the wifi 5 Ghz? Which device? Cause the client makes a big difference too, its not just the router!

Like in my case where i have and AX6000 from xiaomi and on my mi 8 i get excellent wifi range and speeds on a big house, but a family member with Mi A2 lite have much worse range and speeds!

As we discussed in the Brazilian forum, I suspect (but I have no evidences) that you may be right and in fact this router may have the additional amplifiers. However I believe the TX power might be reduced by the firmware due to regulatory issues. There are some reports of the russian version running a debug firmware which greatly increases the singal range.

I tested the wifi range with a laptop (with a Wifi 6E card - Intel AX210), an iPhone 11 and an iPad (on the laptop with Windows 10 I used the command "netsh wlan show interface" to monitor the signal strength and connection speed plus IPERF3 to test the troughput).

Other 802.11ac access points (TP-Link Archer AC2300 with stock firmware and Archer C7 v4 running OpenWRT) installed in the exact same location as the AX3 have a significant better 5GHz coverage.

1 Like

Do you know if the Brazilian version (ax3 pro 4 core, with 4 amplifiers, at least they say it). Support the Chinese firmware?

Mine is stuck an xx.24

Huawei support said me this "Huawei AX3 Pro comes with Quad-core 1.4 GHz CPU and two high-power independent signal amplifiers at 2.4 GHz and two medium-power independent signal amplifiers at 5 GHz"

First you should try to get the firmware of the Brazilan and the enhanced version. quad core and four amplifiers is the most powerful there is, maybe there are differences in the C specification (c500, c506). this is nonsense. if the CE version only has more languages, every improvement makes sense. or there are regional updates that are only relevant. it is. There are however hi1152 or SKY85333-11 chip

only the downgrade visit is correct - only China Version

You know what is about ver. ??

if you need the complet desaster

For WS7200-20 only AX3 Pro Quad Core in CN Version

china version can set network for malaysia?

Hi All. After purchasing three AX3 Pro QuadCore to use as access points, I feel really disappointed by Huawei lack of support.

I purchased the model WS7200-30, announced as a "Brazilian Version" (where I live) but I understand this model is being sold across multiple countries in Americas (including Canada).

However Huawei is not updating the firmware of this device. Theses routers have only a "check for updates" that always return "you are already using the latest version" and there is no webpage from where the firmware can be downloaded.

To make things worse, a Huawei representative responded to another Brazilian user in the official forum that the user should contact the dealer for firmware updates (?!?!?!).

This device in terms of hardware and features is not bad (considering the low cost), but the support is terrible. Since this router will never see OpenWrt running on it, and the support for the original firmware is non-existent, then I strongly do not recommend it to any one.


Olá amigo fiz isso e sentir uma melhoria grande está mais fluente mais solto com a att que estava nele final xxx 24 parceria que estava agarrando algo agora está rápido o meu e ax3p vg

Google translate FTW.

1 Like

hello friend i did it and feel a big improvement is more fluent more loose with an att that was in it end xxx 24 partnership that was grabbing something now it's fast mine and ax3p

It's a bit off-topic but...

I've enabled 160mhz band for my 5g wifi, but I don't see it active. The apps says that it's a 80mhz band.

I know that my smartphone must support 160mhz, but I use a huawei p30 pro, so ali should be able to see/use the 160mhz.

Any tips?

Hello my friend do you have the notion of how to unlock in the wps option of the router thanks

Hello friend I use the p30 pro also it is only connected at 80ghz even the 30 pro is not 160 GHz

I have had the Quad Core (Pro) AX3 global model for several months, it came from the factory with firmware (C500) and has never been updated. ... until this week, and on August 11, 2021 it was finally receive an update, now in

I read this thread, and the spread of the updates is a mess.

1 Like

Did you notice any function change?

I've seen is that only Chinese version gets updated frequently.

No, I don't appreciate differences or changes in the administration panel. And obviously there is no official changelog from Huawei.

You can see it in the upgrade web page.