Struggling with VLANs due to some gaps in my knowledge - looking for help on an e2e solution

Lhutz · 2025-04-06T00:48:48.631Z

Thanks for the clarifications. Here is the requested output from my router:

root@protectli-router:~# ubus call system board
{
	"kernel": "6.6.73",
	"hostname": "protectli-router",
	"system": "Intel(R) Celeron(R) CPU  J1800  @ 2.41GHz",
	"model": "Protectli FW2",
	"board_name": "protectli-fw2",
	"rootfs_type": "ext4",
	"release": {
		"distribution": "OpenWrt",
		"version": "24.10.0",
		"revision": "r28427-6df0e3d02a",
		"target": "x86/64",
		"description": "OpenWrt 24.10.0 r28427-6df0e3d02a",
		"builddate": "1738624177"
	}
}

root@protectli-router:~# cat /etc/config/network

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fd64:333:8758::/48'
	option packet_steering '1'

config device
	option name 'br-lan'
	option type 'bridge'
	list ports 'eth1'

config interface 'lan'
	option device 'br-lan'
	option proto 'static'
	option ipaddr '192.168.88.1'
	option netmask '255.255.255.0'

config interface 'wan'
	option device 'eth0'
	option proto 'dhcp'

config interface 'wan6'
	option device 'eth0'
	option proto 'dhcpv6'

config interface 'tailscale'
	option proto 'none'
	option device 'tailscale0'

config device
	option type 'bridge'
	option name 'br-guest'
	option bridge_empty '1'

config interface 'guest'
	option proto 'static'
	option device 'br-guest'
	option ipaddr '192.168.10.1'
	option netmask '255.255.255.0'

root@protectli-router:~# cat /etc/config/dhcp

config dnsmasq
	option domainneeded '1'
	option localise_queries '1'
	option rebind_protection '1'
	option rebind_localhost '1'
	option local '/lan/'
	option domain 'lan'
	option expandhosts '1'
	option authoritative '1'
	option readethers '1'
	option leasefile '/tmp/dhcp.leases'
	option resolvfile '/tmp/resolv.conf.d/resolv.conf.auto'
	option localservice '1'
	option ednspacket_max '1232'
	option sequential_ip '1'
	list rebind_domain '<REDACTED>'

config dhcp 'lan'
	option interface 'lan'
	option start '100'
	option limit '150'
	option leasetime '12h'
	option dhcpv4 'server'

config dhcp 'wan'
	option interface 'wan'
	option ignore '1'

config odhcpd 'odhcpd'
	option maindhcp '0'
	option leasefile '/tmp/hosts/odhcpd'
	option leasetrigger '/usr/sbin/odhcpd-update'
	option loglevel '4'

<HOSTS REDACTED (DHCP clients)>

config dhcp 'guest'
	option interface 'guest'
	option start '100'
	option limit '150'
	option leasetime '12h'

root@protectli-router:~# cat /etc/config/firewall

config defaults
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option synflood_protect '1'

config zone
	option name 'lan'
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'ACCEPT'
	list network 'lan'

config zone
	option name 'wan'
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option masq '1'
	option mtu_fix '1'
	list network 'wan'
	list network 'wan6'

config forwarding
	option src 'lan'
	option dest 'wan'

config rule
	option name 'Allow-DHCP-Renew'
	option src 'wan'
	option proto 'udp'
	option dest_port '68'
	option target 'ACCEPT'
	option family 'ipv4'

config rule
	option name 'Allow-Ping'
	option src 'wan'
	option proto 'icmp'
	option icmp_type 'echo-request'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-IGMP'
	option src 'wan'
	option proto 'igmp'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-DHCPv6'
	option src 'wan'
	option proto 'udp'
	option dest_port '546'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-MLD'
	option src 'wan'
	option proto 'icmp'
	option src_ip 'fe80::/10'
	list icmp_type '130/0'
	list icmp_type '131/0'
	list icmp_type '132/0'
	list icmp_type '143/0'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Input'
	option src 'wan'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	list icmp_type 'router-solicitation'
	list icmp_type 'neighbour-solicitation'
	list icmp_type 'router-advertisement'
	list icmp_type 'neighbour-advertisement'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Forward'
	option src 'wan'
	option dest '*'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-IPSec-ESP'
	option src 'wan'
	option dest 'lan'
	option proto 'esp'
	option target 'ACCEPT'

config rule
	option name 'Allow-ISAKMP'
	option src 'wan'
	option dest 'lan'
	option dest_port '500'
	option proto 'udp'
	option target 'ACCEPT'

config zone
	option name 'tailscale'
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'ACCEPT'
	option masq '1'
	list network 'tailscale'

config forwarding
	option src 'tailscale'
	option dest 'lan'

config forwarding
	option src 'tailscale'
	option dest 'wan'

config forwarding
	option src 'lan'
	option dest 'tailscale'

config rule
	option name 'Allow_mDNS'
	list proto 'udp'
	option src '*'
	option src_port '5353'
	list dest_ip '224.0.0.251'
	option dest_port '5353'
	option target 'ACCEPT'

config zone
	option name 'guest'
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	list network 'guest'

config forwarding
	option src 'guest'
	option dest 'wan'

config rule

config rule
	option name 'Allow-DNS-Guest'
	option src 'guest'
	option dest_port '53'
	option target 'ACCEPT'

config rule
	option name 'Allow-DHCP-Guest'
	list proto 'udp'
	option src 'guest'
	option dest_port '67'
	option target 'ACCEPT'

psherman · 2025-04-06T00:55:01.213Z

Looks 99% good.

You have an orphaned config rule between the forwarding statement and the guest dns rule -- delete that orphaned line:

Lhutz:

config forwarding
	option src 'guest'
	option dest 'wan'

config rule

config rule
	option name 'Allow-DNS-Guest'
	option src 'guest'
	option dest_port '53'
	option target 'ACCEPT'

And for the guest bridge, add eth1.10 so it looks like this:

config device
	option type 'bridge'
	option name 'br-guest'
	list ports 'eth1.10'

Restart and that's it... router is done (with the guest network). You'll repeat the process (later) with the IoT network.

Next, we can work with the switch. We just need to see /etc/config/network and we need to know what ports connect to the router and each of the APs.

Lhutz · 2025-04-06T01:00:25.560Z

Thanks for that! Note that I have the router connected to the switch on port 1, and ports 2-4 contain ethernet connections for the 3 APs.

Here's the switch config:

root@OpenWrt:~# cat /etc/config/network

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fdd1:c18d:7ff7::/48'
	option packet_steering '1'

config device 'switch'
	option name 'switch'
	option type 'bridge'
	option macaddr 'fc:22:f4:f8:f6:94'
	list ports 'lan1'
	list ports 'lan2'
	list ports 'lan3'
	list ports 'lan4'
	list ports 'lan5'
	list ports 'lan6'
	list ports 'lan7'
	list ports 'lan8'

config bridge-vlan 'lan_vlan'
	option device 'switch'
	option vlan '1'
	option ports 'lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8'

config device
	option name 'switch.1'
	option macaddr 'fc:22:f4:f8:f6:94'

config interface 'lan'
	option device 'switch.1'
	option proto 'static'
	option ipaddr '192.168.88.99'
	option netmask '255.255.255.0'
	option ip6assign '60'
	option gateway '192.168.88.1'

psherman · 2025-04-06T01:41:04.221Z

You didn't mention which ports are used for the router and APs. I'm going to make some assumptions. You'll see the patterns, so you can always adjust if this is wrong:

lan1: router
lan2: AP1
lan3: AP2
lan4: AP3
lan5: main lan
lan6: main lan
lan7: guest
lan8: iot

The guest and IoT ports will be for testing, you can assign them later however you want.

First thing we're going to do is to edit this:

Lhutz:

config bridge-vlan 'lan_vlan'
	option device 'switch'
	option vlan '1'
	option ports 'lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8'

so that it looks like this:

config bridge-vlan
	option device 'switch'
	option vlan '1'
	list ports 'lan1:u*' 
	list ports 'lan2:u*' 
	list ports 'lan3:u*' 
	list ports 'lan4:u*'
	list ports 'lan5:u*'
	list ports 'lan6:u*'

Now we'll add a bridge VLAN for the guest network:

config bridge-vlan
	option device 'switch'
	option vlan '10'
	list ports 'lan1:t' 
	list ports 'lan2:t' 
	list ports 'lan3:t' 
	list ports 'lan4:t' 
	list ports 'lan7:u*'

And finally add an unmanaged interface for the guest network:

config interface 'guest'
	option device 'switch.10'
	option proto 'none'

Restart the switch after these changes. Connect the router to port 1, and then you can connect a computer to port 6 and it should get an address in the main lan, and then port 7 and it should get one in the guest network.

Assuming this works as expected, we'll now move on to your APs.... post the following from your APs:

ubus call system board
cat /etc/config/network

Lhutz · 2025-04-06T01:43:52.009Z

Sorry about the ports. I edited my post above w/ the port info, but too late it seems. Here it is again:

On the switch, port 1 is connected to the router. Ports 2-4 are connected to the APs. The other 4 ports are vacant.

I'll look at your instructions now for the switch and report back.

psherman · 2025-04-06T01:46:03.873Z

Looks like my assumptions line up nicely with your desired port allocations. Report back when you've got those done.

Lhutz · 2025-04-06T01:56:48.901Z

Hey great, that worked! Port 6 gives me a 192.168.88.0/24 address and port 7 gives me a 192.168.10.0/24 address.

Here's the output from one of my APs (let me know if you need this from the other 2, but those should be largely the same):

root@basement-sunroom-ap:~# ubus call system board
{
	"kernel": "6.6.73",
	"hostname": "basement-sunroom-ap",
	"system": "ARMv7 Processor rev 0 (v7l)",
	"model": "Netgear Nighthawk X4S R7800",
	"board_name": "netgear,r7800",
	"rootfs_type": "squashfs",
	"release": {
		"distribution": "OpenWrt",
		"version": "24.10.0",
		"revision": "r28427-6df0e3d02a",
		"target": "ipq806x/generic",
		"description": "OpenWrt 24.10.0 r28427-6df0e3d02a",
		"builddate": "1738624177"
	}
}

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fd2f:ef1c:810::/48'
	option packet_steering '1'

config device
	option name 'br-lan'
	option type 'bridge'
	list ports 'lan1'
	list ports 'lan2'
	list ports 'lan3'
	list ports 'lan4'

config interface 'lan'
	option device 'br-lan'
	option proto 'dhcp'

config interface 'wan'
	option device 'wan'
	option proto 'dhcp'

config interface 'wan6'
	option device 'wan'
	option proto 'dhcpv6'

psherman · 2025-04-06T02:02:24.265Z

Lhutz:

Here's the output from one of my APs (let me know if you need this from the other 2, but those should be largely the same):

Only need the one, assuming that the others are the same or very similar.

I'm going to assume that port lan1 is used as the uplink to the switch, and we'll set ports 3 and 4 as guest and IoT (again, for testing). Port 2 will be the normal lan.

Start by adding bridge VLANs:

config bridge-vlan
	option device 'br-lan'
	option vlan '1'
	list ports 'lan1:u*'
	list ports 'lan2:u*'

config bridge-vlan
	option device 'br-lan'
	option vlan '10'
	list ports 'lan1:t'
	list ports 'lan3:u*'

Edit the lan interface to use br-lan.1:

config interface 'lan'
	option device 'br-lan.1'
	option proto 'dhcp'

And add an unmanaged interface for the guest:

config interface 'guest'
	option device 'br-lan.10'
	option proto 'none'

Now you can add a wifi SSID and associate it with network guest. Obviously restart after making these changes. You'll be able to plug a computer into port 2 and get the normal lan, and port 3 to get the guest network, and the new wifi guest network should work as expected, too.

Repeat for the other APs.

If all of that is successful, you can follow the same recipe to create your IoT network, with minor adaptations which should hopefully be apparent by the discussion we've been having and the patterns involved here.

Let me know how you get on, and if you have any questions about adding that last network.

Lhutz · 2025-04-06T02:12:28.450Z

It looks like this partially works. I can connect to the guest SSID and i get a guest IP, but I can still communicate with other clients on my management network. For example, as a guest I can still ssh to my router and access the luci web interface. How do i complete the isolation?

psherman · 2025-04-06T02:17:37.479Z

What tests are you running, specifically?

I don’t see any reason why you would have any inter-vlan routing.

Lhutz · 2025-04-06T02:20:33.466Z

For example:

Connect to port 3 on the AP. I get a 192.168.10.0/24 address (guest network).
I then attempt to visit 192.168.88.1 (the IP of my router). I can see the luci interface and even ssh to the router at this address. I can also access other clients on the .88.0 network (such as my switch and other random DHCP clients).

psherman · 2025-04-06T02:23:41.167Z

Are you using a computer with both Ethernet and WiFi? Is WiFi still enabled? If so, disable it and test again.

Lhutz · 2025-04-06T02:25:04.641Z

Nope, i turned off wifi on the laptop before i connected to the guest port on the AP. I also ran the same test while connected via wifi (with no other connection) to the guest ssid with the same results.

psherman · 2025-04-06T02:26:21.661Z

Let’s review the final router configuration.

cat /etc/config/network
cat /etc/config/firewall

Lhutz · 2025-04-06T02:28:52.931Z

root@protectli-router:~# cat /etc/config/network

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fd64:333:8758::/48'
	option packet_steering '1'

config device
	option name 'br-lan'
	option type 'bridge'
	list ports 'eth1'

config interface 'lan'
	option device 'br-lan'
	option proto 'static'
	option ipaddr '192.168.88.1'
	option netmask '255.255.255.0'

config interface 'wan'
	option device 'eth0'
	option proto 'dhcp'

config interface 'wan6'
	option device 'eth0'
	option proto 'dhcpv6'

config interface 'tailscale'
	option proto 'none'
	option device 'tailscale0'

config device
	option type 'bridge'
	option name 'br-guest'
	list ports 'eth1.10'

config interface 'guest'
	option proto 'static'
	option device 'br-guest'
	option ipaddr '192.168.10.1'
	option netmask '255.255.255.0'

root@protectli-router:~# cat /etc/config/firewall

config defaults
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option synflood_protect '1'

config zone
	option name 'lan'
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'ACCEPT'
	list network 'lan'

config zone
	option name 'wan'
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	option masq '1'
	option mtu_fix '1'
	list network 'wan'
	list network 'wan6'

config forwarding
	option src 'lan'
	option dest 'wan'

config rule
	option name 'Allow-DHCP-Renew'
	option src 'wan'
	option proto 'udp'
	option dest_port '68'
	option target 'ACCEPT'
	option family 'ipv4'

config rule
	option name 'Allow-Ping'
	option src 'wan'
	option proto 'icmp'
	option icmp_type 'echo-request'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-IGMP'
	option src 'wan'
	option proto 'igmp'
	option family 'ipv4'
	option target 'ACCEPT'

config rule
	option name 'Allow-DHCPv6'
	option src 'wan'
	option proto 'udp'
	option dest_port '546'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-MLD'
	option src 'wan'
	option proto 'icmp'
	option src_ip 'fe80::/10'
	list icmp_type '130/0'
	list icmp_type '131/0'
	list icmp_type '132/0'
	list icmp_type '143/0'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Input'
	option src 'wan'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	list icmp_type 'router-solicitation'
	list icmp_type 'neighbour-solicitation'
	list icmp_type 'router-advertisement'
	list icmp_type 'neighbour-advertisement'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-ICMPv6-Forward'
	option src 'wan'
	option dest '*'
	option proto 'icmp'
	list icmp_type 'echo-request'
	list icmp_type 'echo-reply'
	list icmp_type 'destination-unreachable'
	list icmp_type 'packet-too-big'
	list icmp_type 'time-exceeded'
	list icmp_type 'bad-header'
	list icmp_type 'unknown-header-type'
	option limit '1000/sec'
	option family 'ipv6'
	option target 'ACCEPT'

config rule
	option name 'Allow-IPSec-ESP'
	option src 'wan'
	option dest 'lan'
	option proto 'esp'
	option target 'ACCEPT'

config rule
	option name 'Allow-ISAKMP'
	option src 'wan'
	option dest 'lan'
	option dest_port '500'
	option proto 'udp'
	option target 'ACCEPT'

config zone
	option name 'tailscale'
	option input 'ACCEPT'
	option output 'ACCEPT'
	option forward 'ACCEPT'
	option masq '1'
	list network 'tailscale'

config forwarding
	option src 'tailscale'
	option dest 'lan'

config forwarding
	option src 'tailscale'
	option dest 'wan'

config forwarding
	option src 'lan'
	option dest 'tailscale'

config rule
	option name 'Allow_mDNS'
	list proto 'udp'
	option src '*'
	option src_port '5353'
	list dest_ip '224.0.0.251'
	option dest_port '5353'
	option target 'ACCEPT'

config zone
	option name 'guest'
	option input 'REJECT'
	option output 'ACCEPT'
	option forward 'REJECT'
	list network 'guest'

config forwarding
	option src 'guest'
	option dest 'wan'

config rule
	option name 'Allow-DNS-Guest'
	option src 'guest'
	option dest_port '53'
	option target 'ACCEPT'

config rule
	option name 'Allow-DHCP-Guest'
	list proto 'udp'
	option src 'guest'
	option dest_port '67'
	option target 'ACCEPT'

psherman · 2025-04-06T02:45:17.340Z

There is no firewall allowances for lan > guest or guest > lan

The only possible path is mdns, but I don't think this is relevant (you can try removing or disabling this rule, though):

Lhutz:

config rule
	option name 'Allow_mDNS'
	list proto 'udp'
	option src '*'
	option src_port '5353'
	list dest_ip '224.0.0.251'
	option dest_port '5353'
	option target 'ACCEPT'

From your computer while it is connected to the guest network, let's see the output of:

traceroute 192.168.88.x

where x gets replaced by the last octet of a device that is on the lan (and not the router itself).

Lhutz · 2025-04-06T02:53:01.012Z

Sorry, i probably should have tried traceroute first to not waste your time. Looking at the traceroute output, it was clear that traffic was traversing my tailscale network and making its way to other clients via that route, which is not surprising since my router is a subnet router for my tailnet. I temporarily turned off the tailscale network connection on my laptop and now everything is behaving as expected. The tailnet is for my use only at the moment and will never be accessible to anyone who wouldn't be allowed on the management network anyway, so this is fine.

Just one more question for you:

If I wanted to, say, route some traffic between vlan1 and vlan10 (let's say i want to allow vlan10 to connect to port 123 on a specific ip, or even port 123 on all clients in vlan1. What would i need to do exactly? I ask this as when I wall off the IoT devices, i do need them to be able to connect to some non-IoT clients on the main/management vlan.

psherman · 2025-04-06T03:06:22.568Z

Lhutz:

If I wanted to, say, route some traffic between vlan1 and vlan10 (let's say i want to allow vlan10 to connect to port 123 on a specific ip, or even port 123 on all clients in vlan1

You'd add a rule like this:

config rule
	option name 'Allow-port123-iot2lan'
	option src 'iot'
	option dest_port '123'
	option dest 'lan'
	list dest_ip '192.168.88.x'
	option target 'ACCEPT'

You could also allow the lan to reach the iot network in whole or in part with rules or forward stanzas... if in whole:

config forwarding
	option src 'lan'
	option dest 'iot'

Lhutz · 2025-04-06T03:07:47.638Z

Thanks so much for your time and expertise on this. I've learned a lot as well.

system · 2025-04-16T03:07:57.527Z

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.