After a succesful flash the performance of WRT is great except for a minor issue. I read around a bit and i have the Micron NAND variant with no bad blocks. Nevertheless, I went ahead with the installation of 19.07.1. The only problem is that the configuration is reset every time the router reboots which is really annoying. I attach the dmesg
. Any help would be greatly appreciated.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 19.07.1, r10911-c155900f66
-----------------------------------------------------
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 4.14.167 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 SMP Wed Jan 29 16:05:35 2020
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3 Pro
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 1c000000 @ 00000000 (usable)
[ 0.000000] memory: 04000000 @ 20000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat 80572720, node_mem_map 81003000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from 0x80575744 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[ 0.000000] pcpu-alloc: s26224 r8192 d22928 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130560
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=0004ca40
[ 0.000000] Readback ErrCtl register=0004ca40
[ 0.000000] Memory: 512044K/524288K available (4745K kernel code, 242K rwdata, 588K rodata, 1260K init, 255K bss, 12244K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007812] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073972] pid_max: default: 32768 minimum: 301
[ 0.078741] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085249] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.093995] Hierarchical SRCU implementation.
[ 0.099092] smp: Bringing up secondary CPUs ...
[ 0.104285] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.104294] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.104306] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.104436] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.163812] Synchronize counters for CPU 1: done.
[ 0.197719] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.197729] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.197736] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.197808] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.254762] Synchronize counters for CPU 2: done.
[ 0.285248] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.285256] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.285263] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.285339] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.339945] Synchronize counters for CPU 3: done.
[ 0.369806] smp: Brought up 1 node, 4 CPUs
[ 0.377658] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.387449] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.393752] pinctrl core: initialized pinctrl subsystem
[ 0.400381] NET: Registered protocol family 16
[ 0.410947] FPU Affinity set after 11720 emulations
[ 0.411663] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.716917] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.721962] ***** Xtal 40MHz *****
[ 0.725321] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.730421] Port 0 N_FTS = 1b105000
[ 0.733888] Port 1 N_FTS = 1b105000
[ 0.737328] Port 2 N_FTS = 1b102800
[ 1.892538] PCIE2 no card, disable it(RST&CLK)
[ 1.896899] -> 21007f2
[ 1.899299] PCIE0 enabled
[ 1.901893] PCIE1 enabled
[ 1.904495] PCI host bridge /pcie@1e140000 ranges:
[ 1.909269] MEM 0x0000000060000000..0x000000006fffffff
[ 1.914431] IO 0x000000001e160000..0x000000001e16ffff
[ 1.919627] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.935678] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.941449] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.947268] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.954868] PCI host bridge to bus 0000:00
[ 1.958971] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.965742] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.971632] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.978353] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.986275] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.986314] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.986326] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[ 1.986390] pci 0000:00:00.0: supports D1
[ 1.986399] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.986646] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.986676] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.986690] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff]
[ 1.986739] pci 0000:00:01.0: supports D1
[ 1.986747] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.987134] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 1.987183] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.987473] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.987690] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[ 1.987753] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.988077] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.988106] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[ 1.988186] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.994701] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.001648] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.008173] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.015116] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.021833] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.028590] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 2.035312] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 2.042072] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.049311] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.054249] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.060980] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.068260] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.073150] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.081292] clocksource: Switched to clocksource GIC
[ 2.087723] NET: Registered protocol family 2
[ 2.092847] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.099735] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.106176] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.112582] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.118349] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.124808] NET: Registered protocol family 1
[ 2.129134] PCI: CLS 0 bytes, default 32
[ 2.361238] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.367692] Crashlog allocated RAM at address 0x3f00000
[ 2.373088] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 2.382177] random: fast init done
[ 2.389847] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.395620] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.408848] bounce: pool size: 64 pages
[ 2.412710] io scheduler noop registered
[ 2.416533] io scheduler deadline registered (default)
[ 2.422758] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.432618] console [ttyS0] disabled
[ 2.436158] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.445195] console [ttyS0] enabled
[ 2.452071] bootconsole [early0] disabled
[ 2.462393] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.469466] Enable NFI Clock
[ 2.472427] # MTK NAND # : Use HW ECC
[ 2.476090] Device found in MTK table, ID: 2cda, EXT_ID: 909506
[ 2.482031] Support this Device in MTK table! 2cda
[ 2.486983] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.493465] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 2.499786] nand: Micron NAND 256MiB 3,3V 8-bit
[ 2.504313] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.511888] Scanning device for bad blocks
[ 3.039458] 10 fixed-partitions partitions found on MTD device MT7621-NAND
[ 3.046318] Creating 10 MTD partitions on "MT7621-NAND":
[ 3.051636] 0x000000000000-0x000000040000 : "Bootloader"
[ 3.057855] 0x000000040000-0x000000080000 : "Config"
[ 3.063695] 0x000000080000-0x0000000c0000 : "Bdata"
[ 3.069385] 0x0000000c0000-0x000000100000 : "Factory"
[ 3.075372] 0x000000100000-0x000000140000 : "crash"
[ 3.081051] 0x000000140000-0x0000001c0000 : "crash_syslog"
[ 3.087476] 0x0000001c0000-0x000000200000 : "reserved0"
[ 3.093615] 0x000000200000-0x000000600000 : "kernel_stock"
[ 3.099976] 0x000000600000-0x000000a00000 : "kernel"
[ 3.105876] 0x000000a00000-0x00000ff80000 : "ubi"
[ 3.113426] [mtk_nand] probe successfully!
[ 3.118220] Signature matched and data read!
[ 3.122509] load_fact_bbt success 2047
[ 3.126890] libphy: Fixed MDIO Bus: probed
[ 3.203840] libphy: mdio: probed
[ 4.607474] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.614174] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.625266] NET: Registered protocol family 10
[ 4.631400] Segment Routing with IPv6
[ 4.635150] NET: Registered protocol family 17
[ 4.639642] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.652568] 8021q: 802.1Q VLAN Support v1.8
[ 4.659807] UBI: auto-attach mtd9
[ 4.663224] ubi0: attaching mtd9
[ 6.569525] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 6.924614] ubi0: scanning is finished
[ 6.945720] ubi0: attached mtd9 (name "ubi", size 245 MiB)
[ 6.951198] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.958065] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.964833] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.971775] ubi0: good PEBs: 1964, bad PEBs: 0, corrupted PEBs: 0
[ 6.977837] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 6.985038] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1661070859
[ 6.994141] ubi0: available PEBs: 0, total reserved PEBs: 1964, PEBs reserved for bad PEB handling: 40
[ 7.003441] ubi0: background thread "ubi_bgt0d" started, PID 396
[ 7.005386] block ubiblock0_0: created from ubi0:0(rootfs)
[ 7.014916] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 7.021873] hctosys: unable to open rtc device (rtc0)
[ 7.027157] usb_vbus: disabling
[ 7.037474] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 7.048953] Freeing unused kernel memory: 1260K
[ 7.053504] This architecture does not have kernel memory protection.
[ 7.618870] init: Console is alive
[ 7.622626] init: - watchdog -
[ 8.265123] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.336185] usbcore: registered new interface driver usbfs
[ 8.341833] usbcore: registered new interface driver hub
[ 8.347271] usbcore: registered new device driver usb
[ 8.359381] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 8.368396] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.373784] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 8.391437] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 8.400608] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 8.407331] hub 1-0:1.0: USB hub found
[ 8.411155] hub 1-0:1.0: 2 ports detected
[ 8.415720] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.421029] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 8.428514] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 8.435122] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.444075] hub 2-0:1.0: USB hub found
[ 8.447892] hub 2-0:1.0: 1 port detected
[ 8.456618] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.481596] init: - preinit -
[ 9.184022] mtk_soc_eth 1e100000.ethernet: PPE started
[ 9.255088] random: procd: uninitialized urandom read (4 bytes read)
[ 12.407469] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 503
[ 12.483197] UBIFS error (ubi0:1 pid 501): 0x801d0e30: failed to recover master node
[ 12.490837] UBIFS error (ubi0:1 pid 501): 0x801d0e48: dumping first master node
[ 12.498153] magic 0x6101831
[ 12.501830] crc 0xae07cef5
[ 12.505560] node_type 7 (master node)
[ 12.509717] group_type 0 (no node group)
[ 12.514061] sqnum 3
[ 12.517010] len 512
[ 12.520130] highest_inum 64
[ 12.523178] commit number 0
[ 12.526127] flags 0x1
[ 12.529246] log_lnum 3
[ 12.532212] root_lnum 13
[ 12.535248] root_offs 0
[ 12.538195] root_len 48
[ 12.541247] gc_lnum 15
[ 12.544285] ihead_lnum 13
[ 12.547319] ihead_offs 2048
[ 12.550524] index_size 48
[ 12.553577] lpt_lnum 9
[ 12.556526] lpt_offs 9903
[ 12.559731] nhead_lnum 9
[ 12.562698] nhead_offs 10240
[ 12.565992] ltab_lnum 9
[ 12.568939] ltab_offs 9915
[ 12.572159] lsave_lnum 0
[ 12.575109] lsave_offs 0
[ 12.578055] lscan_lnum 13
[ 12.581088] leb_cnt 1895
[ 12.584308] empty_lebs 1880
[ 12.587516] idx_lebs 1
[ 12.590466] total_free 238964736
[ 12.594122] total_dirty 3888
[ 12.597330] total_used 160
[ 12.600450] total_dead 0
[ 12.603411] total_dark 11556864
[ 12.607041] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 12.614443] mount_root: failed to mount -t ubifs /dev/ubi0_1 /tmp/overlay: Invalid argument
[ 12.623151] mount_root: overlay filesystem has not been fully initialized yet
[ 12.630525] mount_root: switching to ubifs overlay
[ 12.635431] mount_root: switching to ubifs failed - fallback to ramoverlay
[ 12.658089] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.741809] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 12.756622] procd: - early -
[ 12.759598] procd: - watchdog -
[ 13.441447] procd: - watchdog -
[ 13.444912] procd: - ubus -
[ 13.515552] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.577008] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.583812] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.591035] procd: - init -
[ 13.960595] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.025585] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.037828] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a
[ 14.045463] Backport generated by backports.git v4.19.98-1-0-g8204eb99
[ 14.053762] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.065711] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 14.108437] xt_time: kernel timezone is -0000
[ 14.158617] bus=0x1, slot = 0x0, irq=0x0
[ 14.181910] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 14.181910]
[ 14.193817] urngd: v1.0.2 started.
[ 14.329781] random: crng init done
[ 14.333208] random: 6 urandom warning(s) missed due to ratelimiting
[ 14.396688] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 14.414248] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
[ 22.072052] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 22.074901] bus=0x2, slot = 0x1, irq=0x0
[ 22.101789] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 22.101789]
[ 22.165192] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 22.199559] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
[ 29.845506] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 29.852844] PPP generic driver version 2.4.2
[ 29.858501] NET: Registered protocol family 24
[ 29.865785] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 41.466590] mtk_soc_eth 1e100000.ethernet: PPE started
[ 41.476840] device eth0 entered promiscuous mode
[ 41.482962] br-lan: port 1(eth0.1) entered blocking state
[ 41.488431] br-lan: port 1(eth0.1) entered disabled state
[ 41.494562] device eth0.1 entered promiscuous mode
[ 41.503953] br-lan: port 1(eth0.1) entered blocking state
[ 41.509384] br-lan: port 1(eth0.1) entered forwarding state
[ 41.515481] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.472342] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 541.020976] br-lan: port 1(eth0.1) entered disabled state
[ 541.034773] device eth0.1 left promiscuous mode
[ 541.039523] br-lan: port 1(eth0.1) entered disabled state
[ 541.082570] device eth0 left promiscuous mode
[ 541.097369] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 541.258512] device eth0 entered promiscuous mode
[ 541.264274] br-lan: port 1(eth0.1) entered blocking state
[ 541.269721] br-lan: port 1(eth0.1) entered disabled state
[ 541.275642] device eth0.1 entered promiscuous mode
[ 541.283559] br-lan: port 1(eth0.1) entered blocking state
[ 541.289037] br-lan: port 1(eth0.1) entered forwarding state
[ 570.967014] br-lan: port 1(eth0.1) entered disabled state
[ 570.982438] device eth0.1 left promiscuous mode
[ 570.987320] br-lan: port 1(eth0.1) entered disabled state
[ 571.022285] device eth0 left promiscuous mode
[ 571.032930] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 571.208266] device eth0 entered promiscuous mode
[ 571.213943] br-lan: port 1(eth0.1) entered blocking state
[ 571.219412] br-lan: port 1(eth0.1) entered disabled state
[ 571.225462] device eth0.1 entered promiscuous mode
[ 571.233092] br-lan: port 1(eth0.1) entered blocking state
[ 571.238568] br-lan: port 1(eth0.1) entered forwarding state
[ 577.067123] br-lan: port 1(eth0.1) entered disabled state
[ 577.085174] device eth0.1 left promiscuous mode
[ 577.090048] br-lan: port 1(eth0.1) entered disabled state
[ 577.132579] device eth0 left promiscuous mode
[ 577.144616] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 577.348260] device eth0 entered promiscuous mode
[ 577.353981] br-lan: port 1(eth0.1) entered blocking state
[ 577.359433] br-lan: port 1(eth0.1) entered disabled state
[ 577.365511] device eth0.1 entered promiscuous mode
[ 577.375721] br-lan: port 1(eth0.1) entered blocking state
[ 577.381206] br-lan: port 1(eth0.1) entered forwarding state
[ 630.868413] mtk_soc_eth 1e100000.ethernet eth0: port 1 link down
[ 676.961400] mtk_soc_eth 1e100000.ethernet eth0: port 3 link up
[ 679.569377] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[ 683.354907] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 688.502909] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 879.796043] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 879.805392] br-lan: port 2(wlan0) entered blocking state
[ 879.810704] br-lan: port 2(wlan0) entered disabled state
[ 879.816483] device wlan0 entered promiscuous mode
[ 880.657540] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 880.664266] br-lan: port 2(wlan0) entered blocking state
[ 880.669570] br-lan: port 2(wlan0) entered forwarding state
[ 906.099798] device wlan0 left promiscuous mode
[ 906.104490] br-lan: port 2(wlan0) entered disabled state
[ 906.898351] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 906.909604] br-lan: port 2(wlan0) entered blocking state
[ 906.915032] br-lan: port 2(wlan0) entered disabled state
[ 906.920836] device wlan0 entered promiscuous mode
[ 906.926145] br-lan: port 2(wlan0) entered blocking state
[ 906.931495] br-lan: port 2(wlan0) entered forwarding state
[ 907.323187] br-lan: port 2(wlan0) entered disabled state
[ 907.347739] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 907.354477] br-lan: port 2(wlan0) entered blocking state
[ 907.359770] br-lan: port 2(wlan0) entered forwarding state
[ 991.674784] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 991.684684] br-lan: port 3(wlan1) entered blocking state
[ 991.689990] br-lan: port 3(wlan1) entered disabled state
[ 991.696106] device wlan1 entered promiscuous mode
[ 994.240451] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 994.247180] br-lan: port 3(wlan1) entered blocking state
[ 994.252503] br-lan: port 3(wlan1) entered forwarding state