【solved】Oh my god, what should I do [er-x sysupgrade help]

skveen · September 7, 2021, 1:25am

hello
I downloaded the 21.02 for edgeroute-x rom here
ubnt_edgerouter-x-initramfs-kernel.bin

Keep restarting after installation

###############################
Then I learned from here that only 19.07.8 is supported
https://openwrt.org/toh/views/toh_extended_all?dataflt[Model%7E%5D=EdgeRouter+*

###############################
How do I flash back to the old version
Why is the unsupported firmware put in the new firmware catalog and marked as stable?
###############################
What do I do：
19.07.3 update to 21.02-update; 21.02-update to 21.02-initramfs (both form webui)
21.02-initramfs to 19.07.8 (from serial)

skveen · September 7, 2021, 1:47am

I have flashed the firmware back to 19.07.8
However, there are still problems:
The configuration cannot be saved. When the device is restarted, the configuration is lost

Start log:

root@OpenWrt:/# reboot
root@OpenWrt:/# [  113.491784] br-lan: port 1(eth0.1) entered disabled state
[  113.509025] device eth0.1 left promiscuous mode
[  113.518392] br-lan: port 1(eth0.1) entered disabled state
[  113.572786] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[  113.813617] device eth0 left promiscuous mode
[  113.902205] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[  118.049607] reboot: Restarting system

===================================================================
                MT7621   stage1 code 10:33:11 (ASIC)
                CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL4 FB_DL: 0xe, 1/0 = 546/478 39000000
PLL2 FB_DL: 0x12, 1/0 = 522/502 49000000
PLL3 FB_DL: 0x12, 1/0 = 772/252 49000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1
000E:|    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1    1
000F:|    0    0    0    0    1    1    1    1    1    1    1    1    1    0    0    0
0010:|    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0    0
0011:|    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 15
rank 0 fine = 64
B:|    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001C1B
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    10 7 10 8 9 6 11 6 8 10
10 |    9 11 8 11 8 12
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =27 DQS1 = 28
==================================================================
bit     DQS0     bit      DQS1
0  (1~51)26  8  (3~52)27
1  (1~47)24  9  (2~51)26
2  (1~50)25  10  (3~54)28
3  (1~53)27  11  (2~53)27
4  (1~51)26  12  (2~54)28
5  (1~50)25  13  (3~52)27
6  (1~52)26  14  (2~54)28
7  (1~49)25  15  (3~53)28
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    11 10 12 8 10 8 12 8 9 12
10 |    9 12 8 12 8 12
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
DQ loop=15, cmp_err_1 = ffff11aa
DQ loop=14, cmp_err_1 = ffff00aa
dqs_perbyte_dly.last_dqdly_pass[1]=14,  finish count=1
DQ loop=13, cmp_err_1 = ffff00a0
DQ loop=12, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=12,  finish count=2
byte:0, (DQS,DQ)=(9,8)
byte:1, (DQS,DQ)=(8,8)
20,data:89
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=50000000 HZ BUS=16666666 HZ
===================================================================


U-Boot 1.1.3 (Nov  2 2015 - 16:39:31)

Board: Ralink APSoC DRAM:  256 MB
relocate_code Pointer at: 8ffb0000

Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe1960
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [01 DA 90 95 46]
Device found in MTK table, ID: 1da, EXT_ID: 909546
Support this Device in MTK table! 1da
select_chip
[NAND]select ecc bit:12, sparesize :112 spare_per_sector=28
Signature matched and data read!
load_fact_bbt success 2047
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=112,   mtd->erasesize=131072  devinfo.iowidth=8
..
UBNT e50 13-02079-19 788A200B76C8
UBNT BD type=e50, mac=788A200B76C8, s/n=788A200B76C8, mrev=19, k_idx=0
============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Nov  2 2015  Time:16:39:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 880 MHZ ####
 estimate memory size =256 Mbytes
#Reset_MT7530
set port isolation

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
default: 3                                                                                                                                                            0

3: System Boot system code via Flash.
## Booting image at bfd40000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.241
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3554392 Bytes =  3.4 MB
   Load Address: 80001000
   Entry Point:  80001000
.......................................................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256

Starting kernel ...

[    0.000000] Linux version 4.14.241 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11364-ef56c85848)) #0 SMP Thu Jul 29 19:50:28 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is UBNT-ERX
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] random: get_random_bytes called from 0x80579744 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=00009240
[    0.000000] Readback ErrCtl register=00009240
[    0.000000] Memory: 250800K/262144K available (4764K kernel code, 239K rwdata, 588K rodata, 2908K init, 255K bss, 11344K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015512] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087832] pid_max: default: 32768 minimum: 301
[    0.097148] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110171] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125901] Hierarchical SRCU implementation.
[    0.135364] smp: Bringing up secondary CPUs ...
[    0.146286] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.146294] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.146306] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.146435] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204731] Synchronize counters for CPU 1: done.
[    0.270060] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.270068] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.270074] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.270142] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.325592] Synchronize counters for CPU 2: done.
[    0.387128] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.387135] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.387141] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.387214] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.445156] Synchronize counters for CPU 3: done.
[    0.504750] smp: Brought up 1 node, 4 CPUs
[    0.516330] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.535798] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    0.548215] pinctrl core: initialized pinctrl subsystem
[    0.559938] NET: Registered protocol family 16
[    0.583362] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.594656] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.605881] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.619515] clocksource: Switched to clocksource GIC
[    0.630897] NET: Registered protocol family 2
[    0.639691] IP idents hash table entries: 4096 (order: 3, 32768 bytes)
[    0.653247] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.666999] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.679780] TCP: Hash tables configured (established 2048 bind 2048)
[    0.692500] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.704000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.716648] NET: Registered protocol family 1
[    2.859502] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.870992] Crashlog allocated RAM at address 0x3f00000
[    2.881532] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    2.901705] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.913206] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.933947] random: fast init done
[    2.942683] io scheduler noop registered
[    2.950377] io scheduler deadline registered (default)
[    2.961647] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.977704] console [ttyS0] disabled
[    2.984766] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    3.002694] console [ttyS0] enabled
[    3.002694] console [ttyS0] enabled
[    3.016487] bootconsole [early0] disabled
[    3.016487] bootconsole [early0] disabled
[    3.034669] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    3.048733] Enable NFI Clock
[    3.054478] # MTK NAND # : Use HW ECC
[    3.061795] Device found in MTK table, ID: 1da, EXT_ID: 909546
[    3.073408] Support this Device in MTK table! 1da
[    3.083137] [NAND]select ecc bit:12, sparesize :112 spare_per_sector=28
[    3.096355] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda
[    3.109006] nand: AMD/Spansion NAND 256MiB 3,3V 8-bit
[    3.119065] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.134162] Scanning device for bad blocks
[    3.780489] 6 fixed-partitions partitions found on MTD device MT7621-NAND
[    3.794007] Creating 6 MTD partitions on "MT7621-NAND":
[    3.804425] 0x000000000000-0x000000080000 : "u-boot"
[    3.815351] 0x000000080000-0x0000000e0000 : "u-boot-env"
[    3.826947] 0x0000000e0000-0x000000140000 : "factory"
[    3.838025] 0x000000140000-0x000000440000 : "kernel1"
[    3.849133] 0x000000440000-0x000000740000 : "kernel2"
[    3.860264] 0x000000740000-0x00000ff00000 : "ubi"
[    3.872562] [mtk_nand] probe successfully!
[    3.881511] Signature matched and data read!
[    3.890020] load_fact_bbt success 2047
[    3.898218] libphy: Fixed MDIO Bus: probed
[    3.972099] libphy: mdio: probed
[    5.388035] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    5.400586] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
[    5.419916] NET: Registered protocol family 10
[    5.430340] Segment Routing with IPv6
[    5.437714] NET: Registered protocol family 17
[    5.446643] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.472451] 8021q: 802.1Q VLAN Support v1.8
[    5.483725] UBI: auto-attach mtd5
[    5.490372] ubi0: attaching mtd5
[    7.389972] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[    7.427455] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up
[    7.844681] ubi0: scanning is finished
[    7.869437] ubi0: attached mtd5 (name "ubi", size 247 MiB)
[    7.880389] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    7.894069] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    7.907581] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    7.921439] ubi0: good PEBs: 1982, bad PEBs: 0, corrupted PEBs: 0
[    7.933563] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[    7.947937] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1364794905
[    7.966113] ubi0: available PEBs: 1938, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
[    7.984833] ubi0: background thread "ubi_bgt0d" started, PID 364
[    7.984860] hctosys: unable to open rtc device (rtc0)
[    8.017168] Freeing unused kernel memory: 2908K
[    8.026213] This architecture does not have kernel memory protection.
[    8.050718] init: Console is alive
[    8.057714] init: - watchdog -
[    8.074108] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.090511] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.119828] init: - preinit -
[    8.265331] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.392034] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   11.413366] procd: - early -
[   11.419195] procd: - watchdog -
[   12.039661] procd: - watchdog -
[   12.046253] procd: - ubus -
[   12.056566] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.110054] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.123071] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.136608] procd: - init -
Please press Enter to activate this console.
[   12.369978] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.386378] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.402710] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.418995] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[   12.460614] xt_time: kernel timezone is -0000
[   12.474484] PPP generic driver version 2.4.2
[   12.484200] NET: Registered protocol family 24
[   12.495344] kmodloader: done loading kernel modules from /etc/modules.d/*
[   12.540687] urngd: v1.0.2 started.
[   12.685092] random: crng init done
[   12.691881] random: 7 urandom warning(s) missed due to ratelimiting
[   24.115586] mtk_soc_eth 1e100000.ethernet: PPE started
[   24.132423] br-lan: port 1(eth0.1) entered blocking state
[   24.143248] br-lan: port 1(eth0.1) entered disabled state
[   24.154897] device eth0.1 entered promiscuous mode
[   24.164548] device eth0 entered promiscuous mode
[   24.177744] br-lan: port 1(eth0.1) entered blocking state
[   24.188557] br-lan: port 1(eth0.1) entered forwarding state
[   24.200211] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   25.150266] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 19.07.8, r11364-ef56c85848
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#

anon50098793 · September 7, 2021, 5:30am

Please use the "Preformatted text </>" button for logs, scripts, configs and general console output.

Please edit your post accordingly. Thank you!

Pico · September 7, 2021, 5:47am

...initramfs... is the wrong image for everyday usage.

the initramfs image is for testing, it saves config in RAM only.
You need the "...sysupgrade..." image

skveen · September 7, 2021, 1:44pm

So
Does Ubiquiti EdgeRouter support 21.02 ?

mk24 · September 7, 2021, 5:59pm

Yes it does. If coming from 19.07.8, you will need to force upgrade and not save settings since the Ethernet is DSA now. This will build a new default DSA configuration which you can then modify to fit your usage (note in the default configuration, the first port "eth0" is the WAN, so plug your PC into one of the other ports to configure on LAN). Trying to keep an old swconfig (non DSA) configuration will make the Ethernet ports inaccessible.

Pico · September 7, 2021, 6:24pm

looks like the ToH entry of edgerouter X has not been updated yet regarding 21.02 (while other devices have already been updated). It still lists 19.08 as latest: https://openwrt.org/toh/hwdata/ubiquiti/ubiquiti_edgerouter_x

tmomas · September 7, 2021, 7:12pm

Done, dataentry updated.

system · September 17, 2021, 7:12pm

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.