[Solved] Loss of WAN IP Address after Reboot

Installing and Using OpenWrt
1

I am having some difficulty where when I reboot my raspberry pi 5 (Running OpenWrt), I need to reboot the ISP Modem to get an IPv4 address for the WAN port. This seemed like a simple issue, but I could not find any previous posts on this issue. I tried running ifup wan and ifup eth1 and I get "Interface wan not found" or "Interface eth1 not found."

I've never used OpenWrt before now, and I like the degree of freedom It's giving me versus TP Deco. But I'm at an impasse. What data or logs can I try and gather and add to this post that can narrow down my WAN IP issue?

For now here are some info:

{
        "kernel": "6.6.73",
        "hostname": "OpenWrt",
        "system": "ARMv8 Processor rev 1",
        "model": "Raspberry Pi 5 Model B Rev 1.0",
        "board_name": "raspberrypi,5-model-b",
        "rootfs_type": "ext4",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10.0",
                "revision": "r28427-6df0e3d02a",
                "target": "bcm27xx/bcm2712",
                "description": "OpenWrt 24.10.0 r28427-6df0e3d02a",
                "builddate": "1738624177"
        }
}

{
        "kernel": "6.6.73",
        "hostname": "OpenWrt",
        "system": "ARMv8 Processor rev 1",
        "model": "Raspberry Pi 5 Model B Rev 1.0",
        "board_name": "raspberrypi,5-model-b",
        "rootfs_type": "ext4",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10.0",
                "revision": "r28427-6df0e3d02a",
                "target": "bcm27xx/bcm2712",
                "description": "OpenWrt 24.10.0 r28427-6df0e3d02a",
                "builddate": "1738624177"
        }
}
root@OpenWrt:~# cat /etc/config/network

config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fdb4:6f51:24e::/48'
        option packet_steering '1'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'eth0'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option ipaddr '192.168.2.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'Wan'
        option proto 'dhcp'
        option device 'eth1'
        option broadcast '1'

config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fdb4:6f51:24e::/48'
        option packet_steering '1'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'eth0'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option ipaddr '192.168.2.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'Wan'
        option proto 'dhcp'
        option device 'eth1'
        option broadcast '1'

root@OpenWrt:~# cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option path 'platform/axi/1001100000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
        option band '5g'
        option channel '36'
        option htmode 'VHT80'
        option disabled '1'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'OpenWrt'
        option encryption 'none'

config dnsmasq
        option domainneeded '1'
        option boguspriv '1'
        option filterwin2k '0'
        option localise_queries '1'
        option rebind_protection '1'
        option rebind_localhost '1'
        option local '/lan/'
        option domain 'lan'
        option expandhosts '1'
        option nonegcache '0'
        option cachesize '1000'
        option authoritative '1'
        option readethers '1'
        option leasefile '/tmp/dhcp.leases'
        option resolvfile '/tmp/resolv.conf.d/resolv.conf.auto'
        option nonwildcard '1'
        option localservice '1'
        option ednspacket_max '1232'
        option filter_aaaa '0'
        option filter_a '0'

config dhcp 'lan'
        option interface 'lan'
        option start '100'
        option limit '150'
        option leasetime '12h'
        option dhcpv4 'server'
        option dhcpv6 'server'
        option ra 'server'
        list ra_flags 'managed-config'
        list ra_flags 'other-config'

config dhcp 'wan'
        option interface 'wan'
        option ignore '1'

config odhcpd 'odhcpd'
        option maindhcp '0'
        option leasefile '/tmp/hosts/odhcpd'
        option leasetrigger '/usr/sbin/odhcpd-update'
        option loglevel '4'

config dhcp 'Wan'
        option interface 'Wan'
        option ignore '1'

config defaults
        option syn_flood '1'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        list network 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        list network 'wan'
        list network 'wan6'
        list network 'Wan'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'
2

Why does there appear to be a Wan and a wan interface ?

Which USB ethernet adapter are you using ? post lsusb.

3

To answer your second question, the raspberry PI 5 has a PCIe port, I am using a Multi-functional All-in-one Mini-Computer Kit Designed for Raspberry Pi 5 SKU:27831

I don't have an answer to your first question... Maybe poor formatting on my part.

4

good on you, we still want the lsusb output.

5

when I type lsusb, I get -ash: lsusb: not found

6

it's in the usbutils package.

7

I will install

8 
Bus 001 Device 001: ID 1d6b:0002 Linux 6.6.73 xhci-hcd xHCI Host Controller
Bus 002 Device 001: ID 1d6b:0003 Linux 6.6.73 xhci-hcd xHCI Host Controller
Bus 003 Device 001: ID 1d6b:0002 Linux 6.6.73 xhci-hcd xHCI Host Controller
Bus 004 Device 001: ID 1d6b:0003 Linux 6.6.73 xhci-hcd xHCI Host Controller
9

sorry, you said PCIe, lspci from pciutils, not usbutils...

1 Like
10 
0000:00:00.0 PCI bridge: Broadcom Inc. and subsidiaries BCM2712 PCIe Bridge (rev 21)
0000:01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet Controller (rev 15)
0001:00:00.0 PCI bridge: Broadcom Inc. and subsidiaries BCM2712 PCIe Bridge (rev 21)
0001:01:00.0 Ethernet controller: Raspberry Pi Ltd RP1 PCIe 2.0 South Bridge
11

ok.

can you force the misbehaviour by a simple reboot ?

in that case reboot it, and post dmesg afterwards, when wan is down.
might need to split it into several posts, each post is limited to 32k chars.

then the new entries after you've restarted your modem.

use the </> button on top of the message window, when you paste the logs.

1 Like
12

The last misbehavior was after a simple reboot. I will reboot it and get dmesg. Maybe offline for a bit.

13 
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1]
[    0.000000] Linux version 6.6.73 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Feb  3 23:09:37 2025
[    0.000000] random: crng init done
[    0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.0
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000001000000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] OF: reserved mem: 0x0000000001000000..0x0000000004ffffff (65536 KiB) map reusable linux,cma
[    0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable atf@0
[    0.000000] OF: reserved mem: 0x000000003fd16360..0x000000003fd16396 (0 KiB) nomap non-reusable nvram@0
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000001ffffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x1fef963c0-0x1fef98fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x00000000ffffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000007ffff]
[    0.000000]   node   0: [mem 0x0000000000080000-0x000000003fbfffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000001ffffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001ffffffff]
[    0.000000] On node 0, zone DMA: 1024 pages in unavailable ranges
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 19 pages/cpu s37288 r8192 d32344 u77824
[    0.000000] pcpu-alloc: s37288 r8192 d32344 u77824 alloc=19*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] CPU features: detected: Virtualization Host Extensions
[    0.000000] CPU features: detected: Hardware dirty bit management
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] CPU features: detected: Spectre-BHB
[    0.000000] CPU features: detected: SSBS not fully self-synchronizing
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 smsc95xx.macaddr=D8:3A:DD:D1:AF:68 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000  console=tty1 console=ttyAMA10,115200 root=PARTUUID=661a1cf7-02 rootfstype=squashfs,ext4 rootwait
[    0.000000] cgroup: Disabling memory control group subsystem
[    0.000000] mempolicy: NUMA default policy overridden to 'interleave:0'
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Fallback order for Node 0: 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2063360
[    0.000000] Policy zone: Normal
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
[    0.000000] Memory: 8078092K/8384512K available (9536K kernel code, 1000K rwdata, 1716K rodata, 512K init, 560K bss, 240884K reserved, 65536K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: 0xffffffc0800100b4
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000132] Console: colour dummy device 80x25
[    0.000136] printk: console [tty1] enabled
[    0.000309] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[    0.000316] pid_max: default: 32768 minimum: 301
[    0.000421] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.000456] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.001128] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.001215] rcu: Hierarchical SRCU implementation.
[    0.001218] rcu:     Max phase no-delay instances is 1000.
[    0.001782] smp: Bringing up secondary CPUs ...
[    0.001968] Detected PIPT I-cache on CPU1
[    0.002008] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1]
[    0.002196] Detected PIPT I-cache on CPU2
[    0.002227] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1]
[    0.002420] Detected PIPT I-cache on CPU3
[    0.002446] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1]
[    0.002472] smp: Brought up 1 node, 4 CPUs
[    0.002489] SMP: Total of 4 processors activated.
[    0.002493] CPU features: detected: 32-bit EL0 Support
[    0.002497] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.002502] CPU features: detected: Common not Private translations
[    0.002506] CPU features: detected: CRC32 instructions
[    0.002510] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.002513] CPU features: detected: Privileged Access Never
[    0.002517] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.002549] CPU: All CPU(s) started at EL2
[    0.002552] alternatives: applying system-wide alternatives
[    0.006834] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.006848] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.007603] pinctrl core: initialized pinctrl subsystem
[    0.007923] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.008399] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.008464] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.008554] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.008688] thermal_sys: Registered thermal governor 'step_wise'
[    0.008698] cpuidle: using governor ladder
[    0.008706] cpuidle: using governor menu
[    0.008778] ASID allocator initialised with 65536 entries
[    0.009080] Serial: AMBA PL011 UART driver
[    0.009777] bcm2835-mbox 107c013880.mailbox: mailbox enabled
[    0.009980] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 15, base_baud = 0) is a PL011 rev2
[    0.009994] printk: console [ttyAMA10] enabled
[    0.676170] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-01-05T15:57:40, variant start_cd
[    0.696220] raspberrypi-firmware soc:firmware: Firmware hash is 30cc5f3700000000000000000000000000000000
[    0.707775] /axi/pcie@120000/rp1: Fixed dependency cycle(s) with /axi/pcie@120000/rp1
[    0.715719] /axi/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /axi/interrupt-controller@7fff9000
[    0.726316] /axi/pcie@120000/rp1: Fixed dependency cycle(s) with /axi/pcie@120000/rp1
[    0.735036] Modules: 29392 pages in range for non-PLT usage
[    0.735038] Modules: 520912 pages in range for PLT usage
[    0.740962] cryptd: max_cpu_qlen set to 1000
[    0.750814] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1
[    0.758279] iommu: Default domain type: Translated
[    0.763095] iommu: DMA domain TLB invalidation policy: strict mode
[    0.769382] SCSI subsystem initialized
[    0.773182] usbcore: registered new interface driver usbfs
[    0.778692] usbcore: registered new interface driver hub
[    0.784033] usbcore: registered new device driver usb
[    0.789197] mc: Linux media interface: v0.10
[    0.793485] videodev: Linux video capture interface: v2.00
[    0.798996] pps_core: LinuxPPS API ver. 1 registered
[    0.803975] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.813149] PTP clock support registered
[    0.817479] clocksource: Switched to clocksource arch_sys_counter
[    0.824561] NET: Registered PF_INET protocol family
[    0.829611] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.839565] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.848179] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.855956] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.864188] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    0.873251] TCP: Hash tables configured (established 65536 bind 65536)
[    0.879956] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear)
[    0.887597] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.894508] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.901911] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.907609] PCI: CLS 0 bytes, default 64
[    0.912021] workingset: timestamp_bits=42 max_order=21 bucket_order=0
[    0.918680] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.924533] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.946001] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.953630] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d503000, parent irq: 27)
[    0.961363] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508380, parent irq: 28)
[    0.969087] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508400, parent irq: 29)
[    0.976818] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d517b00, parent irq: 30)
[    0.985598] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.992442] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@110000 ranges:
[    0.999435] brcm-pcie 1000110000.pcie:   No bus range found for /axi/pcie@110000, using [bus 00-ff]
[    1.008531] brcm-pcie 1000110000.pcie:      MEM 0x1b80000000..0x1bffffffff -> 0x0080000000
[    1.016832] brcm-pcie 1000110000.pcie:      MEM 0x1800000000..0x1b7fffffff -> 0x0400000000
[    1.025134] brcm-pcie 1000110000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[    1.033521] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges:
[    1.040515] brcm-pcie 1000120000.pcie:   No bus range found for /axi/pcie@120000, using [bus 00-ff]
[    1.049607] brcm-pcie 1000120000.pcie:      MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[    1.057913] brcm-pcie 1000120000.pcie:      MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[    1.066216] brcm-pcie 1000120000.pcie:   IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[    1.074518] brcm-pcie 1000120000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[    1.083846] bcm2708_fb soc:fb: Unable to determine number of FBs. Disabling driver.
[    1.091538] bcm2708_fb: probe of soc:fb failed with error -2
[    1.129241] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    1.135853] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 32, base_baud = 6000000) is a Broadcom BCM7271 UART
[    1.146672] iproc-rng200 107d208000.rng: hwrng registered
[    1.152130] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)
[    1.160539] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040
[    1.168336] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1
[    1.175952] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040
[    1.183743] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2
[    1.191359] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020
[    1.199148] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3
[    1.206763] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020
[    1.214552] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4
[    1.222278] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe
[    1.231177] brd: module loaded
[    1.235189] loop: module loaded
[    1.238489] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.246579] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.252386] dwc_otg: FIQ enabled
[    1.252388] dwc_otg: NAK holdoff enabled
[    1.252389] dwc_otg: FIQ split-transaction FSM enabled
[    1.252392] Module dwc_common_port init
[    1.252480] usbcore: registered new interface driver uas
[    1.257818] usbcore: registered new interface driver usb-storage
[    1.263892] mousedev: PS/2 mouse device common for all mice
[    1.277218] rpi-rtc soc:rpi_rtc: registered as rtc0
[    1.283572] rpi-rtc soc:rpi_rtc: setting system clock to 2025-02-25T10:06:49 UTC (1740478009)
[    1.292476] bcm2835-wdt bcm2835-wdt: Poweroff handler already present!
[    1.299031] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.307678] sdhci: Secure Digital Host Controller Interface driver
[    1.313880] sdhci: Copyright(c) Pierre Ossman
[    1.318293] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.324754] NET: Registered PF_INET6 protocol family
[    1.330014] Segment Routing with IPv6
[    1.333691] In-situ OAM (IOAM) with IPv6
[    1.337639] NET: Registered PF_PACKET protocol family
[    1.342711] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.355765] 8021q: 802.1Q VLAN Support v1.8
[    1.364588] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO
[    1.364608] Key type .fscrypt registered
[    1.373598] Key type fscrypt-provisioning registered
[    1.379085] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@110000 ranges:
[    1.386075] brcm-pcie 1000110000.pcie:   No bus range found for /axi/pcie@110000, using [bus 00-ff]
[    1.395168] brcm-pcie 1000110000.pcie:      MEM 0x1b80000000..0x1bffffffff -> 0x0080000000
[    1.403468] brcm-pcie 1000110000.pcie:      MEM 0x1800000000..0x1b7fffffff -> 0x0400000000
[    1.411768] brcm-pcie 1000110000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[    1.421223] brcm-pcie 1000110000.pcie: Forcing gen 2
[    1.426381] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0000:00
[    1.432849] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.438361] pci_bus 0000:00: root bus resource [mem 0x1b80000000-0x1bffffffff] (bus address [0x80000000-0xffffffff])
[    1.448932] pci_bus 0000:00: root bus resource [mem 0x1800000000-0x1b7fffffff pref] (bus address [0x400000000-0x77fffffff])
[    1.460121] pci 0000:00:00.0: [14e4:2712] type 01 class 0x060400
[    1.466164] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.472273] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.597486] brcm-pcie 1000110000.pcie: link up, 2.5 GT/s PCIe x1 (!SSC)
[    1.604149] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
[    1.610193] pci 0000:01:00.0: reg 0x10: [io  0x0000-0x00ff]
[    1.615800] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    1.622625] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[    1.629530] pci 0000:01:00.0: supports D1 D2
[    1.633811] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.667498] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.674144] pci 0000:00:00.0: BAR 8: assigned [mem 0x1b80000000-0x1b800fffff]
[    1.681311] pci 0000:01:00.0: BAR 4: assigned [mem 0x1b80000000-0x1b80003fff 64bit]
[    1.689007] pci 0000:01:00.0: BAR 2: assigned [mem 0x1b80004000-0x1b80004fff 64bit]
[    1.696699] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0100]
[    1.702990] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0100]
[    1.709631] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.714610] pci 0000:00:00.0:   bridge window [mem 0x1b80000000-0x1b800fffff]
[    1.721774] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[    1.730858] pci_bus 0000:00: resource 4 [mem 0x1b80000000-0x1bffffffff]
[    1.737497] pci_bus 0000:00: resource 5 [mem 0x1800000000-0x1b7fffffff pref]
[    1.744572] pci_bus 0000:01: resource 1 [mem 0x1b80000000-0x1b800fffff]
[    1.751213] pci 0000:00:00.0: Max Payload Size set to  128/ 512 (was  128), Max Read Rq  512
[    1.759692] pci 0000:01:00.0: Max Payload Size set to  128/ 128 (was  128), Max Read Rq  512
[    1.768217] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    1.774363] pcieport 0000:00:00.0: PME: Signaling with IRQ 35
[    1.780179] pcieport 0000:00:00.0: AER: enabled with IRQ 35
[    1.785867] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges:
[    1.792860] brcm-pcie 1000120000.pcie:   No bus range found for /axi/pcie@120000, using [bus 00-ff]
[    1.801947] brcm-pcie 1000120000.pcie:      MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000
[    1.810247] brcm-pcie 1000120000.pcie:      MEM 0x1c00000000..0x1effffffff -> 0x0400000000
[    1.818548] brcm-pcie 1000120000.pcie:   IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000
[    1.826845] brcm-pcie 1000120000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000
[    1.836198] brcm-pcie 1000120000.pcie: Forcing gen 2
[    1.841202] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0001:00
[    1.847667] pci_bus 0001:00: root bus resource [bus 00-ff]
[    1.853170] pci_bus 0001:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])
[    1.863737] pci_bus 0001:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])
[    1.874919] pci 0001:00:00.0: [14e4:2712] type 01 class 0x060400
[    1.880963] pci 0001:00:00.0: PME# supported from D0 D3hot
[    1.887103] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.007480] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)
[    2.014137] pci 0001:01:00.0: [1de4:0001] type 00 class 0x020000
[    2.020179] pci 0001:01:00.0: reg 0x10: [mem 0xffffc000-0xffffffff]
[    2.026473] pci 0001:01:00.0: reg 0x14: [mem 0xffc00000-0xffffffff]
[    2.032770] pci 0001:01:00.0: reg 0x18: [mem 0xffff0000-0xffffffff]
[    2.039129] pci 0001:01:00.0: supports D1
[    2.043149] pci 0001:01:00.0: PME# supported from D0 D1 D3hot D3cold
[    2.077485] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[    2.084128] pci 0001:00:00.0: BAR 8: assigned [mem 0x1f00000000-0x1f005fffff]
[    2.091294] pci 0001:01:00.0: BAR 1: assigned [mem 0x1f00000000-0x1f003fffff]
[    2.098460] pci 0001:01:00.0: BAR 2: assigned [mem 0x1f00400000-0x1f0040ffff]
[    2.105624] pci 0001:01:00.0: BAR 0: assigned [mem 0x1f00410000-0x1f00413fff]
[    2.112789] pci 0001:00:00.0: PCI bridge to [bus 01]
[    2.117771] pci 0001:00:00.0:   bridge window [mem 0x1f00000000-0x1f005fffff]
[    2.124933] pci_bus 0001:00: resource 4 [mem 0x1f00000000-0x1ffffffffb]
[    2.131573] pci_bus 0001:00: resource 5 [mem 0x1c00000000-0x1effffffff pref]
[    2.138649] pci_bus 0001:01: resource 1 [mem 0x1f00000000-0x1f005fffff]
[    2.145288] pci 0001:00:00.0: Max Payload Size set to  256/ 512 (was  128), Max Read Rq  512
[    2.153767] pci 0001:01:00.0: Max Payload Size set to  256/ 256 (was  128), Max Read Rq  512
[    2.162278] pcieport 0001:00:00.0: enabling device (0000 -> 0002)
[    2.168420] pcieport 0001:00:00.0: PME: Signaling with IRQ 36
[    2.174226] pcieport 0001:00:00.0: AER: enabled with IRQ 36
[    2.179866] rp1 0001:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200
[    2.188950] rp1 0001:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200
[    2.198214] rp1 0001:01:00.0: enabling device (0000 -> 0002)
[    2.204539] rp1 0001:01:00.0: chip_id 0x20001927
[    2.214369] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 98
[    2.249513] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 104 (d8:3a:dd:d1:af:68)
[    2.260245] xhci-hcd xhci-hcd.0: xHCI Host Controller
[    2.265319] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1
[    2.273025] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810
[    2.282035] xhci-hcd xhci-hcd.0: irq 129, io mem 0x1f00200000
[    2.287878] xhci-hcd xhci-hcd.0: xHCI Host Controller
[    2.292946] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2
[    2.300201] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed
[    2.306386] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    2.314691] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.321941] usb usb1: Product: xHCI Host Controller
[    2.326832] usb usb1: Manufacturer: Linux 6.6.73 xhci-hcd
[    2.332248] usb usb1: SerialNumber: xhci-hcd.0
[    2.336777] hub 1-0:1.0: USB hub found
[    2.340546] hub 1-0:1.0: 2 ports detected
[    2.344661] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[    2.352960] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.360210] usb usb2: Product: xHCI Host Controller
[    2.365101] usb usb2: Manufacturer: Linux 6.6.73 xhci-hcd
[    2.370518] usb usb2: SerialNumber: xhci-hcd.0
[    2.375032] hub 2-0:1.0: USB hub found
[    2.378798] hub 2-0:1.0: 1 port detected
[    2.382943] xhci-hcd xhci-hcd.1: xHCI Host Controller
[    2.388015] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3
[    2.395703] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810
[    2.404707] xhci-hcd xhci-hcd.1: irq 134, io mem 0x1f00300000
[    2.410534] xhci-hcd xhci-hcd.1: xHCI Host Controller
[    2.415602] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4
[    2.422851] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed
[    2.429001] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    2.437297] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.444548] usb usb3: Product: xHCI Host Controller
[    2.449442] usb usb3: Manufacturer: Linux 6.6.73 xhci-hcd
[    2.454856] usb usb3: SerialNumber: xhci-hcd.1
[    2.459372] hub 3-0:1.0: USB hub found
[    2.463139] hub 3-0:1.0: 2 ports detected
[    2.467245] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[    2.475543] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.482792] usb usb4: Product: xHCI Host Controller
[    2.487686] usb usb4: Manufacturer: Linux 6.6.73 xhci-hcd
[    2.493100] usb usb4: SerialNumber: xhci-hcd.1
[    2.497607] hub 4-0:1.0: USB hub found
[    2.501371] hub 4-0:1.0: 1 port detected
[    2.505461] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000
[    2.513256] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0
[    2.521238] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[    2.529504] platform 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[    2.537543] platform 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu
[    2.545578] platform 1000800000.codec: Adding to iommu group 0
[    2.551437] platform 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu
[    2.559647] platform 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu
[    2.567859] platform 1000880000.pisp_be: Adding to iommu group 0
[    2.573905] platform 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[    2.581766] platform 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu
[    2.589802] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success
[    2.596833] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[    2.605103] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success
[    2.612176] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774
[    2.620440] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success
[    2.627665] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO
[    2.627943] mmc1: CQHCI version 5.10
[    2.632818] mmc0: CQHCI version 5.10
[    2.636626] of_cfs_init
[    2.642370] of_cfs_init: OK
[    2.645214] clk: Disabling unused clocks
[    2.659782] uart-pl011 107d001000.serial: no DMA platform data
[    2.684914] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit
[    2.786911] mmc0: new ultra high speed SDR104 SDXC card at address 5048
[    2.793760] mmcblk0: mmc0:5048 SD64G 58.0 GiB
[    2.798934]  mmcblk0: p1 p2
[    2.801780] mmcblk0: mmc0:5048 SD64G 58.0 GiB (quirks 0x00008000)
[    2.847478] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit
[    2.859146] EXT4-fs (mmcblk0p2): mounted filesystem ff313567-e9f1-5a5d-9895-3ba130b4a864 ro with ordered data mode. Quota mode: disabled.
[    2.871561] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    2.878538] Freeing unused kernel memory: 512K
[    2.883025] Run /sbin/init as init process
[    2.887130]   with arguments:
[    2.887131]     /sbin/init
[    2.887132]   with environment:
[    2.887133]     HOME=/
[    2.887134]     TERM=linux
[    2.887621] mmc1: new ultra high speed DDR50 SDIO card at address 0001
[    2.912901] init: Console is alive
[    2.916357] init: - watchdog -
[    2.997397] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.006829] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.020124] init: - preinit -
[    3.061833] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)
[    3.072766] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode
[    3.083656] pps pps0: new PPS source ptp0
[    3.087700] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[    6.238639] macb 1f00100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    7.364945] mount_root: mounting /dev/root with options
[    7.418164] EXT4-fs (mmcblk0p2): re-mounted ff313567-e9f1-5a5d-9895-3ba130b4a864 r/w. Quota mode: disabled.
[    7.453050] insmod: module is already loaded - fat
[    7.458336] insmod: module is already loaded - vfat
[    7.480009] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    7.490391] urandom-seed: Seeding with /etc/urandom.seed
[    7.503839] macb 1f00100000.ethernet eth0: Link is Down
[    7.509817] macb 1f00100000.ethernet: gem-ptp-timer ptp clock unregistered.
[    7.517846] procd: - early -
[    7.520747] procd: - watchdog -
[    8.033339] procd: - watchdog -
[    8.039288] procd: - ubus -
[    8.092102] procd: - init -
[    8.148078] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.159163] i2c_dev: i2c /dev entries driver
[    8.165285] hid: raw HID events driver (C) Jiri Kosina
[    8.171038] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    8.181628] GACT probability on
[    8.184888] Mirror/redirect action on
[    8.189251] u32 classifier
[    8.191963]     input device check on
[    8.195631]     Actions configured
[    8.203712] brcmutil: loading out-of-tree module taints kernel.
[    8.209778] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[    8.217288] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[    8.230471] r8168 Gigabit Ethernet driver 8.054.00-NAPI loaded
[    8.236364] r8168 0000:01:00.0: enabling device (0000 -> 0002)
[    8.257814] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00
[    8.267421] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Random ether addr 3a:f7:32:96:58:e1
[    8.277143] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[    8.290616] r8168  Copyright (C) 2024 Realtek NIC software team <nicfae@realtek.com>
[    8.290616]  This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
[    8.290616]  This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
[    8.322406] usbcore: registered new interface driver usbhid
[    8.328011] usbhid: USB HID core driver
[    8.333497] xt_time: kernel timezone is -0000
[    8.348001] PPP generic driver version 2.4.2
[    8.352419] NET: Registered PF_PPPOX protocol family
[    8.362360] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    8.371131] usbcore: registered new interface driver brcmfmac
[    8.376947] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,5-model-b.bin failed with error -2
[    8.388655] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.raspberrypi,5-model-b.bin
[    8.399934] kmodloader: done loading kernel modules from /etc/modules.d/*
[    8.550624] brcmfmac: brcmf_c_process_txcap_blob: no txcap_blob available (err=-2)
[    8.558508] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Jul 29 2022 02:15:20 version 7.45.250 (70e9766 CY) FWID 01-e53e306b
[    9.032104] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)
[    9.043073] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode
[    9.053884] pps pps0: new PPS source ptp0
[    9.057934] macb 1f00100000.ethernet: gem-ptp-timer ptp clock registered.
[    9.064992] br-lan: port 1(eth0) entered blocking state
[    9.070245] br-lan: port 1(eth0) entered disabled state
[    9.075497] macb 1f00100000.ethernet eth0: entered allmulticast mode
[    9.081960] macb 1f00100000.ethernet eth0: entered promiscuous mode
[    9.111252] eth1: 0xffffffc080e1d000, 3a:f7:32:96:58:e1, IRQ 159
[   12.148637] macb 1f00100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   12.156525] br-lan: port 1(eth0) entered blocking state
[   12.161776] br-lan: port 1(eth0) entered forwarding state
[   12.321906] r8168: eth1: Link is Up - 1Gbps/Full
[   13.347934] r8168: eth1: Link is Down
[   16.481907] r8168: eth1: Link is Up - 1Gbps/Full
14

if this is true, it might be the issue - new random MAC on every reboot.

try overriding the randomized MAC, set the one it generated in the log, on the WAN interface, making it stay the same.

15

Okay! I saw that somewhere. I will learn how to force a static MAC. Thank you Frollic!

If setting the MAC doesn't fix the issue, I will be sure to update this post.

16

FYI, the "error message" will probably still show during boot, but if you run ifconfig, you should see the MAC being the same after every reboot.

17

You are correct, the error still occurs in dmesg, but the there is no misbehavior. Thanks again.

1 Like
18

If your problem is solved, please consider marking this topic as [Solved]. See How to mark a topic as [Solved] for a short how-to.
Thanks! :slight_smile:

1 Like
19

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.