Hello Community,
After many hours of plugging away at this, I was able to find a resolve. I think the problem was with my openvpn config file for the vpns were configured to point at an incorrect DNS server. My laptop is able to work but my iphone is having problems with the internet still, but that is minor. Getting my computer to vpn to the network was more critical.
I am posting the config files I have. Please not that I created a vpn to my private, guest, and tor networks.
/etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fdfb:7e04:aca7::/48'
config interface 'lan'
option type 'bridge'
option ifname 'eth0.1'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ipaddr '192.168.0.1'
option gateway '192.168.0.1'
option broadcast '192.168.0.255'
option dns '8.8.8.8'
config interface 'wan'
option ifname 'eth1.2'
option proto 'dhcp'
option hostname 'infraverse.network'
config interface 'wan6'
option ifname 'eth1.2'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option vid '1'
option ports '0t 1 2 3 5t'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '4 6t'
option vid '2'
config interface 'slave'
option type 'bridge'
option proto 'static'
option ipaddr '172.16.0.1'
option netmask '255.255.0.0'
option ifname 'eth0.3 radio1'
option gateway '172.16.0.1'
option broadcast '172.16.255.255'
config interface 'tor'
option proto 'static'
option ipaddr '10.1.1.1'
option netmask '255.0.0.0'
option type 'bridge'
option ifname 'eth0.4'
config switch_vlan
option device 'switch0'
option vlan '3'
option vid '3'
option ports '0t 5t'
config switch_vlan
option device 'switch0'
option vlan '4'
option vid '4'
option ports '0t 5t'
config interface 'lanvpn'
option proto 'none'
option ifname 'tun0'
config interface 'slavevpn'
option proto 'none'
option ifname 'tun1'
config interface 'torvpn'
option proto 'none'
option ifname 'tun2'
/etc/config/firewall
config defaults
option syn_flood '1'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'REJECT'
config zone
option name 'lan'
list network 'lan'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
config zone
option name 'wan'
list network 'wan'
list network 'wan6'
option input 'REJECT'
option output 'ACCEPT'
option forward 'REJECT'
option masq '1'
option mtu_fix '1'
config rule
option name 'Allow-DHCP-Renew'
option src 'wan'
option proto 'udp'
option dest_port '68'
option target 'ACCEPT'
option family 'ipv4'
config rule
option name 'Allow-Ping'
option src 'wan'
option proto 'icmp'
option icmp_type 'echo-request'
option family 'ipv4'
option target 'ACCEPT'
config rule
option name 'Allow-IGMP'
option src 'wan'
option proto 'igmp'
option family 'ipv4'
option target 'ACCEPT'
config rule
option name 'Allow-DHCPv6'
option src 'wan'
option proto 'udp'
option src_ip 'fc00::/6'
option dest_ip 'fc00::/6'
option dest_port '546'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-MLD'
option src 'wan'
option proto 'icmp'
option src_ip 'fe80::/10'
list icmp_type '130/0'
list icmp_type '131/0'
list icmp_type '132/0'
list icmp_type '143/0'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-ICMPv6-Input'
option src 'wan'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
list icmp_type 'router-solicitation'
list icmp_type 'neighbour-solicitation'
list icmp_type 'router-advertisement'
list icmp_type 'neighbour-advertisement'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-ICMPv6-Forward'
option src 'wan'
option dest '*'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-IPSec-ESP'
option src 'wan'
option dest 'lan'
option proto 'esp'
option target 'ACCEPT'
config rule
option name 'Allow-ISAKMP'
option src 'wan'
option dest 'lan'
option dest_port '500'
option proto 'udp'
option target 'ACCEPT'
config include
option path '/etc/firewall.user'
config include 'miniupnpd'
option type 'script'
option path '/usr/share/miniupnpd/firewall.include'
option family 'any'
option reload '1'
config zone
option name 'slave'
option forward 'REJECT'
option output 'ACCEPT'
option network 'slave'
option input 'REJECT'
config forwarding
option dest 'wan'
option src 'slave'
config rule
option target 'ACCEPT'
option proto 'tcp udp'
option dest_port '53'
option name 'Slave dns'
option src 'slave'
config rule
option target 'ACCEPT'
option proto 'udp'
option dest_port '67-68'
option name 'slave dhcp'
option src 'slave'
config zone
option name 'tor'
option forward 'REJECT'
option output 'ACCEPT'
option network 'tor'
option input 'ACCEPT'
option syn_flood '1'
option conntrack '1'
config rule
option src 'tor'
option proto 'udp'
option dest_port '67'
option target 'ACCEPT'
option name 'tor DHCP'
config rule
option src 'tor'
option proto 'tcp'
option dest_port '9040'
option target 'ACCEPT'
option name 'tor transport'
config rule
option src 'tor'
option proto 'udp'
option dest_port '9053'
option target 'ACCEPT'
option name 'tor dns'
config redirect
option name 'Redirect-Tor-Traffic'
option src 'tor'
option src_dip '!10.1.1.1'
option dest_port '9040'
option proto 'tcp'
option target 'DNAT'
config redirect
option name 'Redirect-Tor-DNS'
option src 'tor'
option src_dport '53'
option dest_port '9053'
option proto 'udp'
option target 'DNAT'
config rule
option name 'Allow-LAN-OpenVPN'
option src '*'
option dest_port '1999'
option proto 'tcp udp'
option target 'ACCEPT'
config zone
option name 'lanvpn'
option network 'lanvpn'
option masq '1'
option output 'ACCEPT'
option input 'ACCEPT'
option forward 'ACCEPT'
option mtu_fix '1'
config rule
option name 'Allow-SLAVE-OpenVPN'
option src '*'
option dest_port '1111'
option proto 'tcp udp'
option target 'ACCEPT'
config zone
option name 'slavevpn'
option network 'slavevpn'
option masq '1'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
option mtu_fix '1'
config rule
option name 'Allow-tor-OpenVPN'
option src '*'
option dest_port '666'
option proto 'tcp udp'
option target 'ACCEPT'
config zone
option name 'torvpn'
option network 'torvpn'
option masq '1'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
option mtu_fix '1'
config forwarding
option dest 'wan'
option src 'slavevpn'
config forwarding
option dest 'wan'
option src 'torvpn'
config forwarding
option dest 'wan'
option src 'lanvpn'
config forwarding
option dest 'slave'
option src 'slavevpn'
config forwarding
option dest 'tor'
option src 'torvpn'
config forwarding
option dest 'lan'
option src 'lanvpn'
config forwarding
option dest 'lanvpn'
option src 'wan'
config forwarding
option dest 'wan'
option src 'lan'
config forwarding
option dest 'wan'
option src 'tor'
config forwarding
option dest 'tor'
option src 'wan'
config rule
option target 'ACCEPT'
option dest_port '67'
option name 'torvpn-DHCP'
option src 'torvpn'
option proto 'udp'
config rule
option target 'ACCEPT'
option proto 'tcp'
option dest_port '9040'
option name 'torvpn-transport'
option src 'torvpn'
config rule
option enabled '1'
option target 'ACCEPT'
option proto 'udp'
option dest_port '9053'
option name 'torvpn-DNS'
option src 'torvpn'
config redirect
option target 'DNAT'
option dest_port '9040'
option name 'Redirect-torvpn-Traffic'
option proto 'tcp'
option src 'torvpn'
option src_dip '!10.1.200.1'
option dest 'lan'
config redirect
option target 'DNAT'
option proto 'udp'
option name 'Redirect-Tor-DNS'
option src 'torvpn'
option src_dport '53'
option dest_port '9053'
/etc/firewall.user
# This file is interpreted as shell script.
# Put your custom iptables rules here, they will
# be executed with each firewall (re-)start.
# Internal uci firewall chains are flushed and recreated on reload, so
# put custom rules into the root chains e.g. INPUT or FORWARD or into the
# special user chains, e.g. input_wan_rule or postrouting_lan_rule.
iptables -A PREROUTING -t nat -p udp --dport 53 -i br-lan -j DNAT --to 192.168.0.1:53
iptables -t nat -A PREROUTING -i wlan1-2 -p udp --dport 53 -j REDIRECT --to-ports 9053
iptables -t nat -A PREROUTING -i wlan1-2 -p tcp --syn -j REDIRECT --to-ports 9040
iptables -t nat -A PREROUTING -i eth0.4 -p udp --dport 53 -j REDIRECT --to-ports 9053
iptables -t nat -A PREROUTING -i eth0.4 -p tcp --syn -j REDIRECT --to-ports 9040
iptables -t nat -A PREROUTING -i tun2 -p udp --dport 53 -j REDIRECT --to-ports 9053
iptables -t nat -A PREROUTING -i tun2 -p tcp --syn -j REDIRECT --to-ports 9040
/etc/config/openvpn
config openvpn 'custom_config'
option config '/etc/openvpn/my-vpn.conf'
config openvpn 'sample_server'
option port '1194'
option proto 'udp'
option dev 'tun'
option ca '/etc/openvpn/ca.crt'
option cert '/etc/openvpn/server.crt'
option key '/etc/openvpn/server.key'
option dh '/etc/openvpn/dh1024.pem'
option server '10.8.0.0 255.255.255.0'
option ifconfig_pool_persist '/tmp/ipp.txt'
option keepalive '10 120'
option compress 'lzo'
option persist_key '1'
option persist_tun '1'
option user 'nobody'
option status '/tmp/openvpn-status.log'
option verb '3'
config openvpn 'sample_client'
option client '1'
option dev 'tun'
option proto 'udp'
list remote 'my_server_1 1194'
option resolv_retry 'infinite'
option nobind '1'
option persist_key '1'
option persist_tun '1'
option user 'nobody'
option ca '/etc/openvpn/ca.crt'
option cert '/etc/openvpn/client.crt'
option key '/etc/openvpn/client.key'
option compress 'lzo'
option verb '3'
config openvpn 'lanvpn'
option enabled '1'
option verb '11'
option log '/var/log/openvpn/openvpn.log'
option log_append '/var/log/openvpn/openvpn.log'
option dev 'tun0'
option port '1999'
option proto 'udp'
option server '192.168.200.0 255.255.255.0'
option client_to_client '1'
option compress 'lzo'
option keepalive '10 120'
option persist_tun '1'
option persist_key '1'
option dh '/etc/openvpn/lan/dh.pem'
option tls_crypt '/etc/openvpn/lan/tc.pem'
option ca '/etc/openvpn/lan/ca.crt'
option cert '/etc/openvpn/lan/lanvpnserver.crt'
option key '/etc/openvpn/lan/lanvpnserver.key'
list push 'redirect-gateway def1'
list push 'route 192.168.0.0 255.255.255.0'
list push 'dhcp-option DNS 192.168.0.1'
list push 'compress lzo'
list push 'persist-tun'
list push 'persist-key'
list push 'dhcp-option DOMAIN lan'
config openvpn 'slavevpn'
option enabled '1'
option verb '3'
option port '1111'
option proto 'udp'
option server '172.16.200.0 255.255.255.0'
option client_to_client '1'
option compress 'lzo'
option keepalive '10 120'
option persist_tun '1'
option persist_key '1'
option dh '/etc/openvpn/slave/dh.pem'
option tls_crypt '/etc/openvpn/slave/tc.pem'
option ca '/etc/openvpn/slave/ca.crt'
option cert '/etc/openvpn/slave/slavevpnserver.crt'
option key '/etc/openvpn/slave/slavevpnserver.key'
list push 'redirect-gateway def1'
list push 'route 172.16.0.0 255.255.0.0'
list push 'dhcp-option DNS 192.168.0.1'
list push 'compress lzo'
list push 'persist-tun'
list push 'persist-key'
list push 'dhcp-option DOMAIN lan'
option dev 'tun1'
config openvpn 'torvpn'
option enabled '1'
option verb '3'
option port '666'
option proto 'udp'
option server '10.1.200.0 255.255.255.0'
option client_to_client '1'
option compress 'lzo'
option keepalive '10 120'
option persist_tun '1'
option persist_key '1'
option dh '/etc/openvpn/tor/dh.pem'
option tls_crypt '/etc/openvpn/tor/tc.pem'
option ca '/etc/openvpn/tor/ca.crt'
option cert '/etc/openvpn/tor/torvpnserver.crt'
option key '/etc/openvpn/tor/torvpnserver.key'
list push 'redirect-gateway def1'
list push 'route 10.1.1.0 255.0.0.0'
list push 'dhcp-option DNS 10.1.1.1'
list push 'compress lzo'
list push 'persist-tun'
list push 'persist-key'
list push 'dhcp-option DOMAIN lan'
option dev 'tun2'
and just in case you want to add your own tor vpn server to connect to remotely [Note: this requires you have installed tor via the opkg install tor tor-geoip command. notice the vpn subnet added to the bottom of the tor file]:
/etc/tor/torrc
type or paste code here## Configuration file for a typical Tor user
## Last updated 22 December 2017 for Tor 0.3.2.8-rc.
## (may or may not work for much older or much newer versions of Tor.)
##
## Lines that begin with "## " try to explain what's going on. Lines
## that begin with just "#" are disabled commands: you can enable them
## by removing the "#" symbol.
##
## See 'man tor', or https://www.torproject.org/docs/tor-manual.html,
## for more options you can use in this file.
##
## Tor will look for this file in various places based on your platform:
## https://www.torproject.org/docs/faq#torrc
## Tor opens a SOCKS proxy on port 9050 by default -- even if you don't
## configure one below. Set "SOCKSPort 0" if you plan to run Tor only
## as a relay, and not make any local application connections yourself.
#SOCKSPort 9050 # Default: Bind to localhost:9050 for local connections.
#SOCKSPort 192.168.0.1:9100 # Bind to this address:port too.
## Entry policies to allow/deny SOCKS requests based on IP address.
## First entry that matches wins. If no SOCKSPolicy is set, we accept
## all (and only) requests that reach a SOCKSPort. Untrusted users who
## can access your SOCKSPort may be able to learn about the connections
## you make.
#SOCKSPolicy accept 192.168.0.0/16
#SOCKSPolicy accept6 FC00::/7
#SOCKSPolicy reject *
## Logs go to stdout at level "notice" unless redirected by something
## else, like one of the below lines. You can have as many Log lines as
## you want.
##
## We advise using "notice" in most cases, since anything more verbose
## may provide sensitive information to an attacker who obtains the logs.
##
## Send all messages of level 'notice' or higher to /var/log/tor/notices.log
Log notice file /var/log/tor/notices.log
## Send every possible message to /var/log/tor/debug.log
#Log debug file /var/log/tor/debug.log
## Use the system log instead of Tor's logfiles
Log notice syslog
## To send all messages to stderr:
#Log debug stderr
## Uncomment this to start the process in the background... or use
## --runasdaemon 1 on the command line. This is ignored on Windows;
## see the FAQ entry if you want Tor to run as an NT service.
RunAsDaemon 1
## The directory for keeping all the keys/etc. By default, we store
## things in $HOME/.tor on Unix, and in Application Data\tor on Windows.
DataDirectory /var/lib/tor
## The port on which Tor will listen for local connections from Tor
## controller applications, as documented in control-spec.txt.
#ControlPort 9051
## If you enable the controlport, be sure to enable one of these
## authentication methods, to prevent attackers from accessing it.
#HashedControlPassword 16:872860B76453A77D60CA2BB8C1A7042072093276A3D701AD684053EC4C
#CookieAuthentication 1
############### This section is just for location-hidden services ###
## Once you have configured a hidden service, you can look at the
## contents of the file ".../hidden_service/hostname" for the address
## to tell people.
##
## HiddenServicePort x y:z says to redirect requests on port x to the
## address y:z.
#HiddenServiceDir /var/lib/tor/hidden_service/
#HiddenServicePort 80 127.0.0.1:80
#HiddenServiceDir /var/lib/tor/other_hidden_service/
#HiddenServicePort 80 127.0.0.1:80
#HiddenServicePort 22 127.0.0.1:22
################ This section is just for relays #####################
#
## See https://www.torproject.org/docs/tor-doc-relay for details.
## Required: what port to advertise for incoming Tor connections.
#ORPort 9001
## If you want to listen on a port other than the one advertised in
## ORPort (e.g. to advertise 443 but bind to 9090), you can do it as
## follows. You'll need to do ipchains or other port forwarding
## yourself to make this work.
#ORPort 443 NoListen
#ORPort 127.0.0.1:9090 NoAdvertise
## The IP address or full DNS name for incoming connections to your
## relay. Leave commented out and Tor will guess.
#Address noname.example.com
## If you have multiple network interfaces, you can specify one for
## outgoing traffic to use.
## OutboundBindAddressExit will be used for all exit traffic, while
## OutboundBindAddressOR will be used for all OR and Dir connections
## (DNS connections ignore OutboundBindAddress).
## If you do not wish to differentiate, use OutboundBindAddress to
## specify the same address for both in a single line.
#OutboundBindAddressExit 10.0.0.4
#OutboundBindAddressOR 10.0.0.5
## A handle for your relay, so people don't have to refer to it by key.
## Nicknames must be between 1 and 19 characters inclusive, and must
## contain only the characters [a-zA-Z0-9].
#Nickname ididnteditheconfig
## Define these to limit how much relayed traffic you will allow. Your
## own traffic is still unthrottled. Note that RelayBandwidthRate must
## be at least 75 kilobytes per second.
## Note that units for these config options are bytes (per second), not
## bits (per second), and that prefixes are binary prefixes, i.e. 2^10,
## 2^20, etc.
#RelayBandwidthRate 100 KBytes # Throttle traffic to 100KB/s (800Kbps)
#RelayBandwidthBurst 200 KBytes # But allow bursts up to 200KB (1600Kb)
## Use these to restrict the maximum traffic per day, week, or month.
## Note that this threshold applies separately to sent and received bytes,
## not to their sum: setting "40 GB" may allow up to 80 GB total before
## hibernating.
##
## Set a maximum of 40 gigabytes each way per period.
#AccountingMax 40 GBytes
## Each period starts daily at midnight (AccountingMax is per day)
#AccountingStart day 00:00
## Each period starts on the 3rd of the month at 15:00 (AccountingMax
## is per month)
#AccountingStart month 3 15:00
## Administrative contact information for this relay or bridge. This line
## can be used to contact you if your relay or bridge is misconfigured or
## something else goes wrong. Note that we archive and publish all
## descriptors containing these lines and that Google indexes them, so
## spammers might also collect them. You may want to obscure the fact that
## it's an email address and/or generate a new address for this purpose.
##
## If you are running multiple relays, you MUST set this option.
##
#ContactInfo Random Person <nobody AT example dot com>
## You might also include your PGP or GPG fingerprint if you have one:
#ContactInfo 0xFFFFFFFF Random Person <nobody AT example dot com>
## Uncomment this to mirror directory information for others. Please do
## if you have enough bandwidth.
#DirPort 9030 # what port to advertise for directory connections
## If you want to listen on a port other than the one advertised in
## DirPort (e.g. to advertise 80 but bind to 9091), you can do it as
## follows. below too. You'll need to do ipchains or other port
## forwarding yourself to make this work.
#DirPort 80 NoListen
#DirPort 127.0.0.1:9091 NoAdvertise
## Uncomment to return an arbitrary blob of html on your DirPort. Now you
## can explain what Tor is if anybody wonders why your IP address is
## contacting them. See contrib/tor-exit-notice.html in Tor's source
## distribution for a sample.
#DirPortFrontPage /etc/tor/tor-exit-notice.html
## Uncomment this if you run more than one Tor relay, and add the identity
## key fingerprint of each Tor relay you control, even if they're on
## different networks. You declare it here so Tor clients can avoid
## using more than one of your relays in a single circuit. See
## https://www.torproject.org/docs/faq#MultipleRelays
## However, you should never include a bridge's fingerprint here, as it would
## break its concealability and potentially reveal its IP/TCP address.
##
## If you are running multiple relays, you MUST set this option.
##
#MyFamily $keyid,$keyid,...
## Uncomment this if you do *not* want your relay to allow any exit traffic.
## (Relays allow exit traffic by default.)
#ExitRelay 0
## Uncomment this if you want your relay to allow IPv6 exit traffic.
## (Relays only allow IPv4 exit traffic by default.)
#IPv6Exit 1
## A comma-separated list of exit policies. They're considered first
## to last, and the first match wins.
##
## If you want to allow the same ports on IPv4 and IPv6, write your rules
## using accept/reject *. If you want to allow different ports on IPv4 and
## IPv6, write your IPv6 rules using accept6/reject6 *6, and your IPv4 rules
## using accept/reject *4.
##
## If you want to _replace_ the default exit policy, end this with either a
## reject *:* or an accept *:*. Otherwise, you're _augmenting_ (prepending to)
## the default exit policy. Leave commented to just use the default, which is
## described in the man page or at
## https://www.torproject.org/documentation.html
##
## Look at https://www.torproject.org/faq-abuse.html#TypicalAbuses
## for issues you might encounter if you use the default exit policy.
##
## If certain IPs and ports are blocked externally, e.g. by your firewall,
## you should update your exit policy to reflect this -- otherwise Tor
## users will be told that those destinations are down.
##
## For security, by default Tor rejects connections to private (local)
## networks, including to the configured primary public IPv4 and IPv6 addresses,
## and any public IPv4 and IPv6 addresses on any interface on the relay.
## See the man page entry for ExitPolicyRejectPrivate if you want to allow
## "exit enclaving".
##
#ExitPolicy accept *:6660-6667,reject *:* # allow irc ports on IPv4 and IPv6 but no more
#ExitPolicy accept *:119 # accept nntp ports on IPv4 and IPv6 as well as default exit policy
#ExitPolicy accept *4:119 # accept nntp ports on IPv4 only as well as default exit policy
#ExitPolicy accept6 *6:119 # accept nntp ports on IPv6 only as well as default exit policy
#ExitPolicy reject *:* # no exits allowed
## Bridge relays (or "bridges") are Tor relays that aren't listed in the
## main directory. Since there is no complete public list of them, even an
## ISP that filters connections to all the known Tor relays probably
## won't be able to block all the bridges. Also, websites won't treat you
## differently because they won't know you're running Tor. If you can
## be a real relay, please do; but if not, be a bridge!
#BridgeRelay 1
## By default, Tor will advertise your bridge to users through various
## mechanisms like https://bridges.torproject.org/. If you want to run
## a private bridge, for example because you'll give out your bridge
## address manually to your friends, uncomment this line:
#PublishServerDescriptor 0
## Configuration options can be imported from files or folders using the %include
## option with the value being a path. If the path is a file, the options from the
## file will be parsed as if they were written where the %include option is. If
## the path is a folder, all files on that folder will be parsed following lexical
## order. Files starting with a dot are ignored. Files on subfolders are ignored.
## The %include option can be used recursively.
#%include /etc/torrc.d/
#%include /etc/torrc.custom
User tor
PidFile /var/run/tor.pid
Log notice file /var/log/tor/notices.log
Log debug file /var/log/tor/debug.log
GeoIPFile /usr/share/tor/geoip
GeoIPv6File /usr/share/tor/geoip6
MaxCircuitDirtiness 60
ExitNodes {us}
StrictNodes 1
VirtualAddrNetworkIPv4 10.192.0.0/10
AutomapHostsSuffixes .onion,.exit
AutomapHostsOnResolve 1
#tor vlan
TransPort 10.1.1.1:9040
DNSPort 10.1.1.1:9053
SocksPort 10.1.1.1:9050
#torvpn
TransPort 10.1.200.1:9040
DNSPort 10.1.200.1:9053
SocksPort 10.1.200.1:9050
#SocksBindAddress 192.168.2.1:9050
#SocksBindAddress 192.168.1.1:9050
I will be creating documentation on how to create this network infrastructure for the community as promised. If you have any questions or feedback to improve this build, please feel free to pm me.
Thanks again to this awesome community and the people at openwrt/lede for makin a great product and working on an awesome project. This truly is wireless Freedom!
Sincerely,
A hummbly commited student
[UPDATE] As promised, I created the how-to on the OpenWrt wiki:
How to Setup Multiple OpenVPN Server to Different VLANs