Hi! I'm russian, so I can make some big mistakes in word semantics, but i'll be simple:
I've made a big mistake by splitting VLAN's in SWITCH settings of my router (asus rt-n14u).
I've changed CPU port to OFF in both of VLAN (1 and 2) than press "SAVE AND APPLY".
After that I can't access router neither via ssh nor serial after vlan edit. DHCP not working.
Via serial I can watch bootup process, but I'm Unable to send data (keyboard not working, Putty won't accept any keystrokes). Log is here:
Summary
U-Boot 1.1.3 (Jan 7 2013 - 11:32:07)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.0.0
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 7 2013 Time:11:32:07
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
The CPU freq = 580 MHZ
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.10.49
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1081561 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1080d9
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
Transferring control to Linux (at address 80000000) ...
Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 16:48:20 CEST 2014
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Asus RT-N14U
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0003282b
[ 0.000000] Readback ErrCtl register=0003282b
[ 0.000000] Memory: 61516k/65536k available (2425k kernel code, 4020k reserved, 570k data, 200k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered protocol family 16
[ 0.100000] bio: create slab at 0
[ 0.110000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.120000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.130000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.140000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.150000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.160000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.170000] Switching to clocksource MIPS
[ 0.180000] NET: Registered protocol family 2
[ 0.190000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.210000] TCP: Hash tables configured (established 512 bind 512)
[ 0.230000] TCP: reno registered
[ 0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] NET: Registered protocol family 1
[ 0.270000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.290000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.330000] msgmni has been set to 120
[ 0.330000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.350000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.370000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.410000] m25p80 spi32766.0: found mx25l6405d, expected w25q128
[ 0.430000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes)
[ 0.440000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.450000] Creating 4 MTD partitions on "spi32766.0":
[ 0.460000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.480000] 0x000000040000-0x000000050000 : "factory"
[ 0.490000] 0x000000050000-0x000001000000 : "firmware"
[ 0.500000] mtd: partition "firmware" extends beyond the end of device "spi32766.0" -- size truncated to 0x7b0000
[ 0.530000] 0x000000158119-0x000000800000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.560000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x380000, len=0x480000
[ 0.590000] 0x000000380000-0x000000800000 : "rootfs_data"
[ 0.600000] ralink_soc_eth 10100000.ethernet: Enabling TSO
[ 0.620000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[ 0.630000] eth0: done loading
[ 0.640000] rt3xxx-usbphy usbphy.3: loaded
[ 0.650000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.660000] TCP: cubic registered
[ 0.660000] NET: Registered protocol family 17
[ 0.670000] Bridge firewalling registered
[ 0.680000] 8021q: 802.1Q VLAN Support v1.8
[ 0.700000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.710000] Freeing unused kernel memory: 200K (802ee000 - 80320000)
procd: Console is alive
procd: - watchdog -
[ 4.140000] usbcore: registered new interface driver usbfs
[ 4.150000] usbcore: registered new interface driver hub
[ 4.160000] usbcore: registered new device driver usb
[ 4.170000] rt2880-pinmux pinctrl.1: pin 1 is not set to gpio mux
[ 4.180000] rt2880-pinmux pinctrl.1: request() failed for pin 1
[ 4.200000] rt2880-pinmux pinctrl.1: pin-1 (pio:1) status -22
[ 4.210000] gpio-keys-polled gpio-keys-polled.5: unable to claim gpio 1, err=-22
[ 4.220000] gpio-keys-polled: probe of gpio-keys-polled.5 failed with error -22
[ 4.240000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.250000] ehci-platform: EHCI generic platform driver
[ 4.460000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 4.480000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 4.490000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.500000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.510000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.550000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.560000] hub 1-0:1.0: USB hub found
[ 4.570000] hub 1-0:1.0: 1 port detected
[ 4.580000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.590000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[ 4.600000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.620000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.690000] hub 2-0:1.0: USB hub found
[ 4.700000] hub 2-0:1.0: 1 port detected
[ 4.710000] leds-gpio gpio-leds.4: pins are not configured from the driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is ready
jffs2 is ready
[ 8.440000] jffs2: notice: (300) jffs2_build_xattr_subsystem: complete building xattr subsystem, 28 of xdatum (1 unchecked, 27 orphan) and 65 of xref (0 dead, 45 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 9.850000] NET: Registered protocol family 10
[ 9.870000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 9.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.910000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 9.920000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 9.940000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.990000] xt_time: kernel timezone is -0000
[ 10.020000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.030000] cfg80211: World regulatory domain updated:
[ 10.040000] cfg80211: DFS Master region: unset
[ 10.050000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.080000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.100000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.130000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.150000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.260000] PPP generic driver version 2.4.2
[ 10.270000] NET: Registered protocol family 24
[ 10.310000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[ 10.320000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
procd: - init complete -
U-Boot 1.1.3 (Jan 7 2013 - 11:32:07)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.0.0
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 7 2013 Time:11:32:07
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
The CPU freq = 580 MHZ
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.10.49
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1081561 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1080d9
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
Transferring control to Linux (at address 80000000) ...
Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 16:48:20 CEST 2014
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Asus RT-N14U
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00032c24
[ 0.000000] Readback ErrCtl register=00032c24
[ 0.000000] Memory: 61516k/65536k available (2425k kernel code, 4020k reserved, 570k data, 200k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered protocol family 16
[ 0.100000] bio: create slab at 0
[ 0.110000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.120000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.130000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.140000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.150000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.160000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.170000] Switching to clocksource MIPS
[ 0.180000] NET: Registered protocol family 2
[ 0.190000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.210000] TCP: Hash tables configured (established 512 bind 512)
[ 0.230000] TCP: reno registered
[ 0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] NET: Registered protocol family 1
[ 0.270000] rt-timer 10000100.timer: maximum frequncy is 2441Hz
[ 0.290000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.330000] msgmni has been set to 120
[ 0.330000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.350000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.370000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.390000] console [ttyS0] enabled, bootconsole disabled
[ 0.410000] m25p80 spi32766.0: found mx25l6405d, expected w25q128
[ 0.430000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes)
[ 0.440000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.450000] Creating 4 MTD partitions on "spi32766.0":
[ 0.460000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.480000] 0x000000040000-0x000000050000 : "factory"
[ 0.490000] 0x000000050000-0x000001000000 : "firmware"
[ 0.500000] mtd: partition "firmware" extends beyond the end of device "spi32766.0" -- size truncated to 0x7b0000
[ 0.530000] 0x000000158119-0x000000800000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.560000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.570000] mtd: partition "rootfs_data" created automatically, ofs=0x380000, len=0x480000
[ 0.590000] 0x000000380000-0x000000800000 : "rootfs_data"
[ 0.600000] ralink_soc_eth 10100000.ethernet: Enabling TSO
[ 0.620000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[ 0.630000] eth0: done loading
[ 0.640000] rt3xxx-usbphy usbphy.3: loaded
[ 0.650000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.660000] TCP: cubic registered
[ 0.660000] NET: Registered protocol family 17
[ 0.670000] Bridge firewalling registered
[ 0.680000] 8021q: 802.1Q VLAN Support v1.8
[ 0.700000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.710000] Freeing unused kernel memory: 200K (802ee000 - 80320000)
procd: Console is alive
procd: - watchdog -
[ 4.140000] usbcore: registered new interface driver usbfs
[ 4.150000] usbcore: registered new interface driver hub
[ 4.160000] usbcore: registered new device driver usb
[ 4.170000] rt2880-pinmux pinctrl.1: pin 1 is not set to gpio mux
[ 4.180000] rt2880-pinmux pinctrl.1: request() failed for pin 1
[ 4.190000] rt2880-pinmux pinctrl.1: pin-1 (pio:1) status -22
[ 4.210000] gpio-keys-polled gpio-keys-polled.5: unable to claim gpio 1, err=-22
[ 4.220000] gpio-keys-polled: probe of gpio-keys-polled.5 failed with error -22
[ 4.240000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.250000] ehci-platform: EHCI generic platform driver
[ 4.460000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[ 4.480000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[ 4.490000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 4.500000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 4.510000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 4.550000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 4.560000] hub 1-0:1.0: USB hub found
[ 4.570000] hub 1-0:1.0: 1 port detected
[ 4.580000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.590000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[ 4.600000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 4.620000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 4.690000] hub 2-0:1.0: USB hub found
[ 4.700000] hub 2-0:1.0: 1 port detected
[ 4.710000] leds-gpio gpio-leds.4: pins are not configured from the driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is ready
jffs2 is ready
[ 8.430000] jffs2: notice: (300) jffs2_build_xattr_subsystem: complete building xattr subsystem, 28 of xdatum (1 unchecked, 27 orphan) and 65 of xref (0 dead, 45 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 9.860000] NET: Registered protocol family 10
[ 9.880000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 9.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.920000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 9.930000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 9.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.000000] xt_time: kernel timezone is -0000
[ 10.040000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.050000] cfg80211: World regulatory domain updated:
[ 10.060000] cfg80211: DFS Master region: unset
[ 10.070000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.090000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.120000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.150000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.170000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.200000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.270000] PPP generic driver version 2.4.2
[ 10.280000] NET: Registered protocol family 24
[ 10.310000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[ 10.330000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
procd: - init complete -
I'm using this firmware:
[openwrt-15.05.1-ramips-mt7620-rt-n14u-squashfs-sysupgrade.bin]