Flashed wrong firmware, able to access login page but default credential is not working any more.
Soft, Hard, 30/30/30 reset nothing worked.
Able to connect via serial console (Serial to USB) but not able to figure out how to reset or upload firmware after extensive web search.
Log attached.
If any one can help.
Quantenna Mini U-Boot
Version: v37.4.0.28 Built: Dec 18 2015 at 20:33:40
br
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: T T T
ARP Retry count exceeded; starting again
T 1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: *
ARP Retry count exceeded; starting again
T 1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: T T T T
ARP Retry count exceeded; starting again
Retry count exceeded; starting again
1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: *
ARP Retry count exceeded; starting again
T 1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: T
ARP Retry count exceeded; starting again
T 1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: T Quantenna Mini U-Boot
Version: v37.4.0.28 Built: Dec 18 2015 at 20:33:40
br
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: *
ARP Retry count exceeded; starting again
T 1G-FD
BOOTP broadcast 1
BOOTP broadcast 2
Retry count exceeded; starting again
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: ###############
done
Bytes transferred = 71748 (0x11844)
Boot reached stage 13
Boot reached stage 12
Valid CRC found in flash restoring env...
Boot reached stage 11
hw_config_id 65535: 'QTM840_5S1_MS_MAC'
Cold boot
Reset status: 0x00000001
Info: data uncached: addr=0xc0000000 size=1024MB
Info: text at 0x88040000, stack at 0x88013ffc(8192), heap at 0x88000000(73728), uboot size 177840
Info: i-cache is enabled
Info: d-cache is enabled
Info: CPU freq is 500000000, dev freq is 125000000
Info: Quantenna U-Boot version:v37.4.0.28
Info: build date 'Jul 13 2016', time '09:42:29'
SPI flash info:
name : mx25l512e
jedec_id : 0xc22010
sector size : 4096
number of sector : 16
frequency : 104000000
flags : 0x2
lock :
DDR_INIT: type = 16, speed = 2, size = 134217728
500MHz
BDA at 0x80002000
In: serial
Out: serial
Err: serial
Boot reached stage 64
Boot reached stage 65
br
Hit any key to stop autoboot: 0
Boot reached stage 80
1G-FD
Using br device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'topaz-linux.lzma.img'.
Load address: 0x83000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################
done
Bytes transferred = 5166008 (0x4ed3b8)
Boot reached stage 81
Boot reached stage 84
Boot reached stage 1
## Booting kernel from Legacy Image at 83000000 ...
Boot reached stage 2
Boot reached stage 3
Image Name: topaz-linux
Image Type: arc Linux Kernel Image (lzma compressed)
Data Size: 5157816 Bytes = 4.9 MB
Load Address: 8493a000
Entry Point: 8493a000
Qtn flags: 00000001
Verifying Checksum ... OK
Boot reached stage 4
Boot reached stage 5
Boot reached stage 6
Boot reached stage 14
Uncompressing Kernel Image ... OK
Boot reached stage 7
Boot reached stage 8
Command line TAG setup
Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
## Unset TAG qtn_flags 1
## Transferring control to Linux (at address 8493a000) ATAG parameters 88068db0 - 88068e08...
[ 0.000000] Linux version 2.6.35.12 (vagrant@vagrant) (gcc version 4.2.1 (ARC_2.3)) #2 Wed Jul 13 09:54:27 CDT 2016
[ 0.000000] Parsing ATAG parameters from bootloader
[ 0.000000] ATAG_CORE: successful parsing
[ 0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
[ 0.000000] Board id: 65535
[ 0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535
[ 0.000000]
[ 0.000000] Processor Family: ARC 700 [0x33]
[ 0.000000] CPU speed : 500.00 Mhz
[ 0.000000] Timers: TIMER1 TIMER0
[ 0.000000] Interrupt Vect Base: 0x88052c00
[ 0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000
[ 0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB
[ 0.000000] ARC700 MMU Ver [2]
[ 0.000000] PAGE SIZE 8k
[ 0.000000] JTLB 128 x 2 = 256 entries
[ 0.000000] uDTLB 8 entr, uITLB 4 entr
[ 0.000000] TLB Refill "will NOT" Flush uTLBs
[ 0.000000] Detected I-cache :
[ 0.000000] Type=2 way set-assoc, Line length=32, Size=16K (enabled)
[ 0.000000] Detected D-cache :
[ 0.000000] Type=4 way set-assoc, Line length=32, Size=16K (enabled)
[ 0.000000] Extensions:
[ 0.000000] MPY: 32x32 with ANY Result Reg MAC MPY: Dual 16 x 16 and 32 x 16
[ 0.000000] DCCM: N/A ICCM: N/A
[ 0.000000] CRC: N/A, SWAP: Present NORM: Present
[ 0.000000] Min-Max: Present, Barrel Shifter: Present
[ 0.000000] Ext Arith Insn: Present
[ 0.000000] Floating Point Extension: N/A
[ 0.000000] On node 0 totalpages: 16383
[ 0.000000] free_area_init_node: node 0, pgdat 85873d3c, node_mem_map 85922024
[ 0.000000] Normal zone: 72 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16311 pages, LIFO batch:3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16311
[ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
[ 0.000000] bootconsole [ruby_early0] enabled
[ 0.000000] PID hash table entries: 512 (order: -2, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes)
[ 0.000000] Memory: 39048KB available (2155K code,1196K data, 12928K init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] clockevent mode switch to [1]
[ 0.000000] clockevent mode switch to [2]
[ 0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592)
[ 0.115000] pid_max: default: 4096 minimum: 301
[ 0.120000] Mount-cache hash table entries: 1024
[ 0.125000] Starting run_ksoftirqd, stack (thread_info) at 85898000 cpu 0
[ 0.130000] NET: Registered protocol family 16
[ 0.135000] Topaz heap in SRAM 88016780<->88020000, B2 BASE 17800
[ 0.150000] bio: create slab <bio-0> at 0
[ 0.155000] watch64: 2003/08/22 Josef 'Jeff' Sipek <jeffpc@xxxxxxxxxxxxx>
[ 0.160000] watch64: Enabling Watch64 extensions...done.
[ 0.165000] Switching to clocksource ARC Timer1
[ 0.175000] NET: Registered protocol family 2
[ 0.180000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
[ 0.185000] TCP established hash table entries: 4096 (order: 2, 32768 bytes)
[ 0.190000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
[ 0.195000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.200000] TCP reno registered
[ 0.205000] NET: Registered protocol family 1
[ 0.695000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.700000] msgmni has been set to 76
[ 0.705000] io scheduler noop registered (default)
[ 1.130000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 1.140000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A
[ 1.145000] console [ttyS0] enabled, bootconsole disabled
[ 1.145000] console [ttyS0] enabled, bootconsole disabled
[ 1.155000] brd: module loaded
[ 1.165000] loop: module loaded
[ 1.170000] spi_flash: Force not to support Protect Mode
[ 1.175000] Creating 3 MTD partitions on "spi_flash":
[ 1.180000] 0x000000000000-0x000000005000 : "uboot"
[ 1.185000] 0x000000005000-0x00000000b000 : "uboot_env"
[ 1.195000] 0x00000000b000-0x000000010000 : "data"
[ 1.200000] spi_flash: SPI flash driver initialized successfully!
[ 1.205000] ruby_health loading
[ 1.205000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000
[ 1.715000] HBM meta: emac rx 0x63c040 to 0x6bc040, wmac rx 0x6bc080 to 0x6dc080
[ 1.720000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 bus_range 0x6ec400 to 0x26ec400 sz 4096 count 8192
[ 1.720000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 bus_range 0x26fc400 to 0x48fc400 sz 17408 count 2048
[ 1.720000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 bus_range 0x0 to 0x0 sz 0 count 4096
[ 1.730000] topaz_busmon_init success
[ 1.730000] topaz_temp_sens_init success
[ 1.735000] u32 classifier
[ 1.740000] input device check on
[ 1.740000] Actions configured
[ 1.745000] Netfilter messages via NETLINK v0.30.
[ 1.750000] nf_conntrack version 0.5.0 (610 buckets, 2440 max)
[ 1.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.765000] TCP cubic registered
[ 1.765000] NET: Registered protocol family 10
[ 1.775000] NET: Registered protocol family 17
[ 1.780000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 1.785000] All bugs added by David S. Miller <davem@redhat.com>
[ 1.800000] Freeing unused kernel memory: 12928k freed [8493a000] TO [855da000]
[ 1.805000] Common mmap addr-space starts 2c0f0000
init started: BusyBox v1.10.3 (2016-07-13 09:43:02 CDT)
starting pid 40, tty '': '/etc/init.d/rcS'
[ 2.105000] load_module: 'bootcfg' using DRAM (offset:0x859f0000, size:0x8e44)
Starting portmap: done
Initializing random number generator... done.
Starting network...
[ 2.765000] load_module: 'rtl8367b' using DRAM (offset:0x86400000, size:0x31eab)
[ 2.770000] rtl8367b: module license 'unspecified' taints kernel.
[ 2.775000] Disabling lock debugging due to kernel taint
[ 2.830000] load_module: 'emaclib' using DRAM (offset:0x863e0000, size:0x5349)
[ 2.945000] load_module: 'switch_vlan' using DRAM (offset:0x863c0000, size:0x2240)
[ 3.040000] load_module: 'switch_tqe' using DRAM (offset:0x863b8000, size:0x4eab)
[ 3.085000] tqe_descs_alloc: 512 tqe_rx_descriptors at kern uncached 0x580d8788 bus 0x80016788
[ 3.165000] load_module: 'dpi' using DRAM (offset:0x859e8000, size:0x1b89)
[ 3.195000] load_module: 'fwt_if' using DRAM (offset:0x86372000, size:0x1658)
[ 3.225000] load_module: 'fwt_ctrl' using DRAM (offset:0x86440000, size:0x23629)
[ 3.280000] load_module: 'switch_emac' using DRAM (offset:0x863a4000, size:0x21cb), SRAM (offset:0x88018da8, size:0x1d0)
[ 3.340000] emac wbsp: 0
[ 3.340000] enable A2 (single)
[ 3.400000] topaz_emac_init, emac0
[ 3.405000] Random stuff A1
[ 3.430000] topaz_emac_init, emac1
emac0 is eth1_0, emac1 is unused
Stateless mode. Using temporary ip address:
Using IP address 1.1.1.2
Netmask is not set
[ 3.685000] emac_lib eth1_0: force link (1000/Full)
[ 3.715000] device eth1_0 entered promiscuous mode
[ 3.735000] br0: port 1(eth1_0) entering forwarding state
[ 3.740000] br0: port 1(eth1_0) entering forwarding state
sed: mnt/jffs2/wireless_conf.txt: No such file or directory
/sbin/ifup -a
ifconfig: SIOCSIFNETMASK: Cannot assign requested address
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
Starting qevt_server
Starting inetd ...
inotify_add_watch: No such file or directory
Starting wireless...
[ 4.770000] FWT: [44:65:7f:5c:8d:7a] add entry, port:emac0 node:0 entries:1
Configuration has been set to default values. Reboot after customizing to ensure correct operation.
complete
/scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:05 up 0 min, load average: 0.16, 0.03, 0.01
/scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:06 up 0 min, load average: 0.16, 0.03, 0.01
'monitor_temperature' is not enabled/set
MAUI Service started....
dhcp service is not enabled in wireless_conf.txt
Starting httpd
bind: Bad file descriptor
bind: Bad file descriptor
starting pid 409, tty '/dev/console': '/bin/sh -l'
BusyBox v1.10.3 (2016-07-13 09:43:02 CDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
quantenna # [ 13.830000] br0.100: no IPv6 routers present
[ 14.460000] br0: no IPv6 routers present
[ 21.300000] FWT: [44:65:7f:5c:8d:76] add entry, port:emac0 node:0 entries:2
Using IP address 1.1.1.2
Netmask is not set
Loading modules
[ 27.035000] load_module: 'qtn_debug' using DRAM (offset:0x863ae800, size:0x403)
[ 27.110000] load_module: 'i2cbus' using DRAM (offset:0x865a0000, size:0x1ce2)
[ 27.220000] load_module: 'qtsens' using DRAM (offset:0x865f5800, size:0x7b6)
[ 27.300000] load_module: 'pm_interval' using DRAM (offset:0x865f8000, size:0x13b2)
[ 27.425000] load_module: 'wlan' using DRAM (offset:0x86700000, size:0x8bbc7)
[ 27.710000] wlan: 0.8.4.2 (0.9.3.3)
[ 27.875000] load_module: 'auc_fw' using DRAM (offset:0x8788e660, size:0x115b)
[ 27.980000] load_module: 'radar' using DRAM (offset:0x866a0000, size:0x1a394)
[ 28.035000] load_module: 'qvspmod' using DRAM (offset:0x866c0000, size:0x10bb3)
[ 28.125000] load_module: 'qdrv' using DRAM (offset:0x87400000, size:0x9a7f5)
[ 28.385000] qdrv wbsp: 0
[ 28.390000] Auc SRAM start 0x88040000 end 0x88070000 size 196608
[ 28.395000] Auc SRAM bank 0 start 0x88040000 end 0x88050000
[ 28.400000] Auc SRAM bank 1 start 0x88050000 end 0x88060000
[ 28.405000] Auc SRAM bank 2 start 0x88060000 end 0x88070000
[ 28.495000] load_module: 'wlan_xauth' using DRAM (offset:0x86538400, size:0x32f)
[ 28.590000] load_module: 'wlan_ccmp' using DRAM (offset:0x865cc000, size:0x177e)
[ 28.705000] load_module: 'wlan_tkip' using DRAM (offset:0x86694000, size:0x2632)
Loading MuC driver (qtn_driver.qtn_ruby.0.bin)
Waiting for Wireless Events from interfaces...
Found power table in /etc/power_tables
[ 29.560000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_eu.txt
[ 29.595000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_us.txt
[ 29.760000] set power_selection 0
[ 29.870000] set power_selection 2
[ 29.875000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0
[ 29.880000] ..... Current RFIC Chip ID -- 0
[ 30.060000] MuC: g_tqe_sem_en 0
[ 30.065000] MuC: build date Tue, 12 Jul 2016 01:27:43 -0700
[ 30.070000] MuC: slow heap begin=0x0022aba0 end=0x003a7ba0
[ 30.075000] MuC: fast heap begin=0x80030800 end=0x80037000
[ 30.080000] MuC: stack start=0x8003efc0 sp=0x8003f724
[ 30.085000] MuC: calstate is 3 (prod), dcache on
[ 30.090000] MuC: RFIC version 1
[ 30.115000] MuC: bb_init: FEM 0x7 bw_mode 0 chan 0 11b 0 11a 1
[ 30.120000] MuC: rf_optimizing_rf_register_map, set rf to 0x75
[ 30.125000] MuC: os_uc, after bb_rf_complete_attach.
[ 30.130000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740
[ 30.135000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0
[ 30.140000] MuC: dynamic one-bit autocorrelation enabled
[ 30.145000] MuC: freq 1 proj 1
[ 30.150000] MuC: QMAT SRAM base 0x80070000
[ 30.150000] MuC: enable IRQs
[ 30.160000] qdrv_mac_reserve_clear: mac reservation table cleared
[ 30.210000] se95: probe of 0-0049 failed with error -121
[ 30.240000] qdrv_mu_stat_init
[ 30.245000] QDRV: no external temperature sensor found
[ 30.260000] MuC: AuC enabled 0xe5101bcc/0x6005b0b8 il 0xe5101288/0xe510128c stats 0x600591f8/0x6005adf80x6006e3c4
[ 30.265000] MuC: Can't allocate more fcs for AuC. Bad... WMAC = 1
[ 30.270000] MuC: Update MU debug flag from 0x00000000 to 0x20000000
[ 30.275000] AuC: Update mu flag : 0x20000000. Max delay = 0
[ 30.290000] QDRV: hardware is 4x4 11ac FO RGMII/PCIe QV840
[ 30.295000] MuC boot succeeded 0.055 seconds
[ 30.560000] load_module: 'wlan_scan_ap' using DRAM (offset:0x85e6c000, size:0x29ce)
[ 30.710000] MuC: freq 1 proj 1
[ 30.715000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done
[ 30.740000] VAP create succeeded 0.020 seconds
[ 31.295000] MuC: calibration ver 0x801
radar in 80MHZ mode
Setting mode to 11ac80
Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v37.3.0.21
Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.48
Selected database version: Regulatory db version: v37.4.0.48
Using /etc/qtn_regulatory_db.bin
radar start with[ 32.615000] DFS_s_radio: parameters updated, region: eu
regulatory eu
dfs_s_radio 0 dfs 0 non-dfs 0 scan 0 auto-channel channel 0
Configure max_boot_cac to -1
[ 33.585000] device wifi0 entered promiscuous mode
[ 33.705000] Enabling SSDP flooding
Beamforming enabled
802.11ac Enabled
[ 34.505000] Enabling SCS
SCS enabled
QTM: load profile gcn
[ 34.720000] qvsp_strm_reset: stream reset
[ 34.770000] qvsp_ioctl_rule_add: rule added
[ 34.775000] qvsp_strm_reset: stream reset
[ 34.825000] qvsp_ioctl_rule_add: rule added
[ 34.830000] qvsp_strm_reset: stream reset
[ 34.880000] qvsp_ioctl_rule_add: rule added
[ 34.885000] qvsp_strm_reset: stream reset
[ 34.935000] qvsp_ioctl_rule_add: rule added
[ 34.940000] qvsp_strm_reset: stream reset
[ 34.995000] qvsp_ioctl_rule_add: rule added
QTM enabled: 1
No core dump generated
monitor reset button
monitor led
[ 37.280000] qdrv_radar_is_rdetection_required: ERROR - channel not yet set
[ 37.330000] Build name: v37.4.0.62.5
[ 37.335000] Build revision: 47559
[ 37.340000] Build type: SDK
[ 37.345000] Build timestamp: 1468421579
[ 37.350000] Platform ID: 432
[ 37.350000] Hardware ID: QV840
[ 37.355000] Hardware revision: bbic4_rev_a2
[ 37.360000] Band: 5GHz
[ 37.365000] Kernel version: 2.6.35
[ 37.370000] Calibration version: disabled
[ 37.375000] DC/IQ cal version: V8.1
[ 37.375000] Power cal version: V8.1
[ 37.380000] MuC firmware: qtn_driver.qtn_ruby.0.bin
[ 37.385000] DSP firmware: rdsp_driver.0.bin
[ 37.390000] AuC firmware: auc_driver.0.bin
[ 37.395000] MAC address 0: 44:65:7f:5c:8d:7b
[ 37.400000] MAC address 1: 00:00:00:00:00:00
[ 37.405000] U-Boot version: v37.4.0.28
Carrier ID 0, uboot update flag 0
complete
[ 37.965000] MuC: Update MU debug flag from 0x20000000 to 0x20000000
[ 37.965000] MuC: MU disabled
[ 37.965000] AuC: Update mu flag : 0x20000000. Max delay = 0
complete
complete
[ 38.120000] MuC: AutoCCA: disabled
[ 38.820000] Disabling SCS
[ 38.835000] MuC: Update MU debug flag from 0x20000000 to 0x20000000
[ 38.835000] MuC: MU disabled
[ 38.835000] AuC: Update mu flag : 0x20000000. Max delay = 0
[ 39.870000] MuC: Update MU debug flag from 0x20000000 to 0x20000000
[ 39.870000] MuC: MU disabled
[ 39.870000] AuC: Update mu flag : 0x20000000. Max delay = 0
[ 39.990000] MuC: #RX data path optimal flag 0
[ 39.995000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x8000f000/6592 cache 0x8002c9e0/13184
[ 39.995000] MuC: auto cs is enabled
[ 40.000000] WPS: push button GPIO pin 4
[ 40.000000] WPS: monitored using polling
[ 40.000000] WPS: active logic is low
[ 40.020000] br0: port 2(wifi0) entering forwarding state
[ 40.020000] br0: port 2(wifi0) entering forwarding state
start-prod: adding default "manufacturer=Quantenna" to /mnt/jffs2/hostapd.conf
start-prod: adding default "device_name=Reference Design" to /mnt/jffs2/hostapd.conf
start-prod: adding default "model_name=Topaz" to /mnt/jffs2/hostapd.conf
start-prod: adding default "model_number=QV840.432" to /mnt/jffs2/hostapd.conf
start-prod: adding default "serial_number=44657F5C8D7B" to /mnt/jffs2/hostapd.conf
start-prod: adding default "friendly_name=UPnP Access Point" to /mnt/jffs2/hostapd.conf
start-prod: adding default "device_type=6-0050F204-1" to /mnt/jffs2/hostapd.conf
Enable ap pin setup in all BSSes
Configuration file: /mnt/jffs2/hostapd.conf
[ 41.110000] br0: port 2(wifi0) entering forwarding state
Using interface wifi0 with hwaddr 44:65:7f:5c:8d:7b and ssid "Quantenna"
ioctl(SIOCGIFADDR): Cannot assign requested address
fail to update anounce pkt: Cannot assign requested address
[ 41.915000] br0: port 2(wifi0) entering forWPS UPnP: SIOCGIwFADDR failed: 99a (Cannot assign rrequested addresds)
ing state
[ 41.915000] br0: port 2(wifi0) entering forwarding state
[ 45.685000] BRIDGE: report flood-forwarding disabled
[ 49.300000] MuC: freq 1 proj 1
[ 49.315000] VAP create succeeded 0.010 seconds
[ 49.350000] device wifi1 entered promiscuous mode
[ 50.200000] br0: port 3(wifi1) entering forwarding state
[ 50.200000] br0: port 3(wifi1) entering forwarding state
[ 57.240000] qdrv_control_input: ERROR - Failed to execute command "set" (2)
[ 169.440000] net_ratelimit: 23 callbacks suppressed
[ 169.440000] qvsp_strm_reset: stream reset
[ 169.460000] MuC: ioctl_power_save, level: 0 -> 5