I am having three devices from A1 (Sercomm Na502) which are not going to work in November so I am trying to install open wrt. Till now I have established serial connection, installed kernel in ram, established SSH and copied sysupgrade file in tmp. After executing sysupgrade command I am getting
Commencing upgrade. Closing all shell sessions.
Command failed: Connection failed. Please give me further instructions.
instructions are on the device info page:
https://openwrt.org/toh/sercomm/na502?s[]=sercomm&s[]=na502#tftp_installation_instructions
this is normal, for any device that goes offline or reboots ...
hang in there, it's (hopefully) reflashing itself.
1 Like
On serial i am getting this:
Watchdog handover: fd=3
- watchdog -
Watchdog does not have CARDRESET support
Fri Oct 14 22:47:15 UTC 2022 upgrade: Sending TERM to remaining processes ...
Fri Oct 14 22:47:19 UTC 2022 upgrade: Sending KILL to remaining processes ...
[ 178.535015] stage2 (2766): drop_caches: 3
Fri Oct 14 22:47:25 UTC 2022 upgrade: Switching to ramdisk...
Fri Oct 14 22:47:27 UTC 2022 upgrade: Performing system upgrade...
Unlocking kernel ...
Writing from to kernel ...
removing ubiblock0_0
[ 182.902682] block ubiblock0_0: released
Volume ID 0, size 31 LEBs (3936256 bytes, 3.7 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 9269248
Volume ID 1, size 73 LEBs (9269248 bytes, 8.8 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 185.022981] reboot: Restarting system
And the restarting is with the original firmware
===================================================================
MT7621 stage1 code 13:15:05 (ASIC)
CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xc, 1/0 = 558/466 31000000
PLL4 FB_DL: 0x14, 1/0 = 810/214 51000000
PLL2 FB_DL: 0x15, 1/0 = 543/481 55000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 32
B:| 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0
opt_dle value:10
DRAMC_R0DELDLY[018]=00001C1C
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 9 13 10 15 9 14 7 4 11
10 | 6 13 9 12 6 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =28 DQS1 = 28
==================================================================
bit DQS0 bit DQS1
0 (1~54)27 8 (0~51)25
1 (1~50)25 9 (1~50)25
2 (0~50)25 10 (1~50)25
3 (1~52)26 11 (2~52)27
4 (1~54)27 12 (1~55)28
5 (1~53)27 13 (2~52)27
6 (1~52)26 14 (0~52)26
7 (1~55)28 15 (1~55)28
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 15 12 15 12 15 10 15 7 7 14
10 | 9 14 9 13 8 11
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff2a00
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
DQS loop = 14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2
DQ loop=15, cmp_err_1 = ffff55aa
DQ loop=14, cmp_err_1 = ffff05aa
DQ loop=13, cmp_err_1 = ffff01aa
DQ loop=12, cmp_err_1 = ffff01a0
DQ loop=11, cmp_err_1 = ffff0180
DQ loop=10, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=10, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=10, finish count=2
byte:0, (DQS,DQ)=(a,8)
byte:1, (DQS,DQ)=(a,8)
20,data:aa
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=16666666 HZ
===================================================================
U-Boot 1.1.3 (Jun 6 2016 - 13:15:24)
Board: Ralink APSoC DRAM: 256 MB
relocate_code Pointer at: 8ffac000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe0a10
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device not found, ID: c2f1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
Env addr : 0x80000
..============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC MT7621AS (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Jun 6 2016 Time:13:15:24
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
Reset switch ...
#Reset_MT7530
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
STANDALONE_LOAD_ADDR is 0xa0600000
..Example expects ABI version 2
Actual U-Boot ABI version 2
******************************************
Uboot StandAlone Entry
******************************************
0, cmd
1, 0x0000000D
cmd : 0x0000000D
0
Example expects ABI version 2
Actual U-Boot ABI version 2
******************************************
Uboot StandAlone Entry
******************************************
0, boot
Flash Sector Number : 522.
***************************************************
Sercomm Boot Version 2.00.1
***************************************************
Entering Firmware : Everything is OK.
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> .......................OK
Image2 Data Checksum --> ..........................................OK
Image1: OK Image2: OK
=================================================
..kernel addr :0xbfd40000
flash base: 0xbfc00000, kernel addr :0xbfd40000, bootloader size: 0x80000, config size 0x80000, fac size : 0x40000
..Erasing NAND Flash...
.Writing to NAND Flash...
done
3: System Boot system code via Flash.
## Booting image at bfd40000 ...
Image Name: OpenWrt Linux-3.10.14
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1457676 Bytes = 1.4 MB
Load Address: 80001000
Entry Point: 80001000
....................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.14 (openwrt@13bc1de213b4) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #2 SMP Thu Jun 3 12:27:31 UTC 2021
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x0bffffff]
[ 0.000000] Normal [mem 0x0c000000-0x0fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] avail: cpu2 is not ready
[ 0.000000] avail: cpu3 is not ready
[ 0.000000] Detected 1 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @8c204000 s6400 r8192 d14080 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00010890
[ 0.000000] Readback ErrCtl register=00010890
[ 0.000000] Memory: 255240k/262144k available (3209k kernel code, 6904k reserved, 827k data, 244k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.132000] Calibrating delay loop... 562.17 BogoMIPS (lpj=1124352)
[ 0.164000] pid_max: default: 32768 minimum: 301
[ 0.168000] Mount-cache hash table entries: 512
[ 0.172000] launch: starting cpu1
[ 0.176000] launch: cpu1 gone!
[ 0.176000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.208000] Synchronize counters for CPU 1: done.
[ 0.216000] Brought up 2 CPUs
[ 0.220000] NET: Registered protocol family 16
[ 0.512000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.516000] PCIE PHY initialize
[ 0.520000] ***** Xtal 40MHz *****
[ 0.524000] start MT7621 PCIe register access
[ 1.100000] RALINK_RSTCTRL = 7000000
[ 1.104000] RALINK_CLKCFG1 = 77ffeff8
[ 1.108000]
[ 1.108000] *************** MT7621 PCIe RC mode *************
[ 1.588000] PCIE0 no card, disable it(RST&CLK)
[ 1.592000] pcie_link status = 0x6
[ 1.596000] RALINK_RSTCTRL= 6000000
[ 1.600000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.604000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 10207f2
[ 1.608000] PCIE1 enabled
[ 1.612000] PCIE2 enabled
[ 1.616000] interrupt enable status: 600000
[ 1.620000] Port 1 N_FTS = 1b105000
[ 1.624000] Port 0 N_FTS = 1b105000
[ 1.628000] config reg done
[ 1.632000] init_rt2880pci done
[ 1.656000] bio: create slab <bio-0> at 0
[ 1.660000] usbcore: registered new interface driver usbfs
[ 1.672000] usbcore: registered new interface driver hub
[ 1.680000] usbcore: registered new device driver usb
[ 1.692000] PCI host bridge to bus 0000:00
[ 1.700000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.716000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.728000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.744000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.760000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.772000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.784000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.800000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.812000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.828000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.840000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.856000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 1.868000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.880000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.892000] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.908000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 1.920000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.932000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.944000] BAR0 at slot 0 = 0
[ 1.948000] bus=0x0, slot = 0x0
[ 1.956000] res[0]->start = 0
[ 1.960000] res[0]->end = 0
[ 1.968000] res[1]->start = 60300000
[ 1.976000] res[1]->end = 6030ffff
[ 1.980000] res[2]->start = 0
[ 1.988000] res[2]->end = 0
[ 1.992000] res[3]->start = 0
[ 2.000000] res[3]->end = 0
[ 2.004000] res[4]->start = 0
[ 2.012000] res[4]->end = 0
[ 2.016000] res[5]->start = 0
[ 2.020000] res[5]->end = 0
[ 2.028000] BAR0 at slot 1 = 0
[ 2.032000] bus=0x0, slot = 0x1
[ 2.040000] res[0]->start = 0
[ 2.044000] res[0]->end = 0
[ 2.052000] res[1]->start = 60310000
[ 2.056000] res[1]->end = 6031ffff
[ 2.064000] res[2]->start = 0
[ 2.072000] res[2]->end = 0
[ 2.076000] res[3]->start = 0
[ 2.080000] res[3]->end = 0
[ 2.088000] res[4]->start = 0
[ 2.092000] res[4]->end = 0
[ 2.100000] res[5]->start = 0
[ 2.104000] res[5]->end = 0
[ 2.112000] bus=0x1, slot = 0x0, irq=0x18
[ 2.120000] res[0]->start = 60000000
[ 2.124000] res[0]->end = 600fffff
[ 2.132000] res[1]->start = 0
[ 2.136000] res[1]->end = 0
[ 2.144000] res[2]->start = 0
[ 2.148000] res[2]->end = 0
[ 2.156000] res[3]->start = 0
[ 2.160000] res[3]->end = 0
[ 2.168000] res[4]->start = 0
[ 2.172000] res[4]->end = 0
[ 2.176000] res[5]->start = 0
[ 2.184000] res[5]->end = 0
[ 2.188000] bus=0x2, slot = 0x1, irq=0x19
[ 2.196000] res[0]->start = 60200000
[ 2.204000] res[0]->end = 602fffff
[ 2.212000] res[1]->start = 0
[ 2.216000] res[1]->end = 0
[ 2.224000] res[2]->start = 0
[ 2.228000] res[2]->end = 0
[ 2.232000] res[3]->start = 0
[ 2.240000] res[3]->end = 0
[ 2.244000] res[4]->start = 0
[ 2.252000] res[4]->end = 0
[ 2.256000] res[5]->start = 0
[ 2.264000] res[5]->end = 0
[ 2.268000] Bluetooth: Core ver 2.16
[ 2.272000] NET: Registered protocol family 31
[ 2.276000] Bluetooth: HCI device and connection manager initialized
[ 2.280000] Bluetooth: HCI socket layer initialized
[ 2.284000] Bluetooth: L2CAP socket layer initialized
[ 2.288000] Bluetooth: SCO socket layer initialized
[ 2.292000] Switching to clocksource MIPS
[ 2.296000] NET: Registered protocol family 2
[ 2.304000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.320000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.332000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.344000] TCP: reno registered
[ 2.352000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.364000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.376000] NET: Registered protocol family 1
[ 2.472000] 4 CPUs re-calibrate udelay(lpj = 1167360)
[ 2.484000] ======= sercomm_button_init =======
[ 2.492000] mt7621_register_gpio_keys_polled start!
[ 2.504000] mt7621_register_gpio_keys_polled ends!
[ 2.516000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.528000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.548000] io scheduler noop registered (default)
[ 2.556000] ======== sercomm_gpio_init ========
[ 2.564000]
[ 2.564000] led on GPIO_LED_POWER
[ 2.576000] ===== sercomm_gpio_ioctl_init =====
[ 2.588000] ====== sercomm_led_ioctl_init =====
[ 2.600000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.616000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.628000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.640000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A
[ 2.656000] Ralink APSoC Hardware Watchdog Timer
[ 2.664000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.680000] Allocate 16 byte aligned buffer: 8045d320
[ 2.688000] Enable NFI Clock
[ 2.696000] # MTK NAND # : Use HW ECC
[ 2.704000] NAND ID [C2 F1 80 95 02, 00809502]
[ 2.712000] Device not found, ID: c2f1
[ 2.720000] Not Support this Device!
[ 2.728000] chip_mode=00000001
[ 2.732000] Support this Device in MTK table! c2f1
[ 2.744000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 2.768000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.780000] Scanning device for bad blocks
[ 2.936000] Bad eraseblock 629 at 0x000004ea0000
[ 3.040000] Signature matched and data read!
[ 3.048000] load_fact_bbt success 1023
[ 3.056000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.076000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.096000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.116000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.136000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 00
[ 3.156000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.172000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.192000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.212000] Creating 10 MTD partitions on "MT7621-NAND":
[ 3.224000] 0x000000000000-0x000007f80000 : "ALL"
[ 3.236000] 0x000000000000-0x000000080000 : "Bootloader"
[ 3.248000] 0x000000080000-0x000000100000 : "Config"
[ 3.256000] 0x000000100000-0x000000140000 : "Factory"
[ 3.268000] 0x000000140000-0x000001540000 : "Firmware1"
[ 3.280000] 0x0000002a3e4c-0x000001540000 : "rootfs"
[ 3.292000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 3.328000] mtd: partition "rootfs_data" created automatically, ofs=0xec0000, len=0x680000
[ 3.348000] 0x000000ec0000-0x000001540000 : "rootfs_data"
[ 3.360000] 0x000001540000-0x000002940000 : "Firmware2"
[ 3.368000] 0x000002940000-0x000002a40000 : "user_storage"
[ 3.380000] 0x000002a40000-0x000003a40000 : "data"
[ 3.392000] 0x000003a40000-0x000006c40000 : "storage"
[ 3.404000] 0x000006c40000-0x000007f80000 : "backup"
[ 3.416000] [mtk_nand] probe successfully!
[ 3.424000] rootfs = 2a3e4c to ec0000
[ 3.432000] rdm_major = 253
[ 3.436000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 3.444000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 3.452000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 3.472000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 3.480000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 3.488000] PROC INIT OK!
[ 3.496000] *****run project phy.
[ 3.508000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.524000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.540000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.556000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.572000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.588000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.604000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.620000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.636000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.652000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.684000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.700000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.716000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.732000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.748000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.764000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.780000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.796000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.812000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.828000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.956000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 3.964000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 3.980000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 3.992000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.004000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.020000] usb usb1: Product: xHCI Host Controller
[ 4.028000] usb usb1: Manufacturer: Linux 3.10.14 xhci-hcd
[ 4.040000] usb usb1: SerialNumber: xhci-hcd
[ 4.048000] hub 1-0:1.0: USB hub found
[ 4.056000] hub 1-0:1.0: 2 ports detected
[ 4.064000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 4.076000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 4.088000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 4.104000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.116000] usb usb2: Product: xHCI Host Controller
[ 4.128000] usb usb2: Manufacturer: Linux 3.10.14 xhci-hcd
[ 4.136000] usb usb2: SerialNumber: xhci-hcd
[ 4.148000] hub 2-0:1.0: USB hub found
[ 4.156000] hub 2-0:1.0: 1 port detected
[ 4.164000] usbcore: registered new interface driver usbserial
[ 4.176000] usbcore: registered new interface driver usbserial_generic
[ 4.188000] usbserial: USB Serial support registered for generic
[ 4.200000] usbcore: registered new interface driver cp210x
[ 4.212000] usbserial: USB Serial support registered for cp210x
[ 4.224000] usbcore: registered new interface driver usb_debug
[ 4.236000] usbserial: USB Serial support registered for debug
[ 4.248000] usbcore: registered new interface driver ftdi_sio
[ 4.260000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 4.272000] usbcore: registered new interface driver pl2303
[ 4.284000] usbserial: USB Serial support registered for pl2303
[ 4.296000] TCP: cubic registered
[ 4.304000] NET: Registered protocol family 10
[ 4.312000] NET: Registered protocol family 17
[ 4.324000] Bluetooth: RFCOMM TTY layer initialized
[ 4.332000] Bluetooth: RFCOMM socket layer initialized
[ 4.344000] Bluetooth: RFCOMM ver 1.11
[ 4.348000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.360000] Bluetooth: BNEP filters: protocol multicast
[ 4.372000] Bluetooth: BNEP socket layer initialized
[ 4.380000] 8021q: 802.1Q VLAN Support v1.8
[ 4.396000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 4.412000] Freeing unused kernel memory: 244K (803f3000 - 80430000)
[ 4.436000] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 4.472000] usb 1-2: New USB device found, idVendor=0e8d, idProduct=7662
[ 4.484000] usb 1-2: New USB device strings: Mfr=4, Product=5, SerialNumber=6
[ 4.500000] usb 1-2: Product: Wireless
[ 4.508000] usb 1-2: Manufacturer: MediaTek Inc.
[ 4.516000] usb 1-2: SerialNumber: 000000000
[ 4.524000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 16, interval 1, burst 0, mult 0, ep 0x8fe2b080, ep_ctx 0xbbc10080, sch_ep 0x8ffbdf80
[ 4.556000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8fe2b0ac, ep_ctx 0xbbc100c0, sch_ep 0x8ffbdd00
[ 4.584000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8fe2b0d8, ep_ctx 0xbbc100a0, sch_ep 0x8ffbda80
[ 4.612000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8ffb4b80, ep_ctx 0xbbc10100, sch_ep 0x8ffbd880
[ 4.640000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8ffb4bac, ep_ctx 0xbbc100e0, sch_ep 0x8ffbd600
[ 4.672000]
[ 4.672000]
[ 4.672000] Unsupported Device!
[ 4.672000] Vendor=e8d ProdID=7662
[ 4.672000] Manufacturer=MediaTek Inc. Product=Wireless
[ 4.672000]
procd: Console i[ 4.828000] Started WatchDog Timer.
s alive
procd: - watchdog started -
procd: - watchdog fd closed -
[ 5.608000] Button Hotplug driver version 0.4.1
[ 5.624000] SCSI subsystem initialized
[ 5.636000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 6.128000] 3C:FFFFFF98:72:FFFFFFF5:FFFFFF9B:10
[ 6.136000] Raeth v3.1 (Tasklet)
[ 6.148000] phy_free_head is 0x1bc1e000!!!
[ 6.156000] phy_free_tail_phy is 0x1bc1fff0!!!
[ 6.164000] txd_pool=bbc20000 phy_txd_pool=1BC20000
[ 6.176000] ei_local->skb_free start address is 0x8fe3a6dc.
[ 6.184000] free_txd: 1bc20010, ei_local->cpu_ptr: 1BC20000
[ 6.196000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 6.204000] ----------------+---------+--------
[ 6.216000] 0xbbc20000 0x1BC20000 0x1BC20000
[ 6.224000]
[ 6.224000] phy_qrx_ring = 0x1bc12000, qrx_ring = 0xbbc12000
[ 6.240000]
[ 6.240000] phy_rx_ring0 = 0x1bc28000, rx_ring0 = 0xbbc28000
[ 6.276000] MT7530 Reset Completed!!
[ 6.284000] change HW-TRAP to 0x17ccf
[ 6.292000] set LAN/WAN LLLLW
[ 6.304000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 6.312000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 6.324000] CDMA_CSG_CFG = 81000000
[ 6.332000] GDMA1_FWD_CFG = 20710000
[ 6.856000] block: attempting to load /etc/config/fstab
[ 6.916000] block: extroot: not configured
jffs2 is ready
jffs2 is ready
[ 7.068000] jffs2: notice: (308) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 7.456000] block: attempting to load /etc/config/fstab
[ 7.468000] block: extroot: not configured
switching to overlay
[ 7.492000] ra2880stop()...Done
[ 7.500000] Free TX/RX Ring Memory!
procd: - early -
procd: - ubus -
procd: - init -
### Set BLE Power Level 5 ###
### Set BLE MAC Address ###
[ 12.480000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 12.500000] tun: Universal TUN/TAP device driver, 1.6
[ 12.508000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.524000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.536000] Type=Restricted Cone
[ 12.548000] nf_conntrack version 0.5.0 (3991 buckets, 15964 max)
[ 12.560000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.580000] usbcore: registered new interface driver btusb
[ 12.596000] usbcore: registered new interface driver cdc_acm
[ 12.608000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 12.748000] xt_time: kernel timezone is -0000
[ 12.760000] usbcore: registered new interface driver cdc_ether
[ 12.780000] usbcore: registered new interface driver option
[ 12.792000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 12.808000] PPP generic driver version 2.4.2
[ 12.820000] NET: Registered protocol family 24
procd: - init complete -
I have been following them, and i am at the end and i don't know what to do anymore
Did you use the tftp method?
1 Like
Yes to transfer kernel from pc to ram.
Then ssh to transfer sysupgrade to /tmp
When i am executing sysupgrade the device restarts and boots with the original firmware
What is the exact filename of the image you are transferring after getting the initramfs image running?
openwrt-22.03.2-ramips-mt7621-sercomm_na502-squashfs-sysupgrade.bin
Why are you using 22.03? Try 23.05. (For both the kernel and the main sysupgrade image)
because it is said on forums that versions after 23 are not working with this device
Ok. Well at least try 22.03.7
I have tried it
less than 1 second
procd: - shutdown -
pā
===================================================================
MT7621 stage1 code 13:15:05 (ASIC)
CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xd, 1/0 = 638/386 35000000
PLL4 FB_DL: 0x13, 1/0 = 567/457 4D000000
PLL2 FB_DL: 0x15, 1/0 = 602/422 55000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 32
B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
opt_dle value:11
DRAMC_R0DELDLY[018]=00001B1A
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 9 13 10 14 9 14 7 4 11
10 | 6 13 9 11 6 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =26 DQS1 = 27
==================================================================
bit DQS0 bit DQS1
0 (1~52)26 8 (1~50)25
1 (1~49)25 9 (1~49)25
2 (1~47)24 10 (1~48)24
3 (1~48)24 11 (2~50)26
4 (1~52)26 12 (1~52)26
5 (1~50)25 13 (0~50)25
6 (1~49)25 14 (1~50)25
7 (1~52)26 15 (2~52)27
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 10 15 12 14 10 15 7 6 13
10 | 9 14 10 13 8 11
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff2a00
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
DQS loop = 14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2
DQ loop=15, cmp_err_1 = ffff45aa
DQ loop=14, cmp_err_1 = ffff05aa
DQ loop=13, cmp_err_1 = ffff01aa
DQ loop=12, cmp_err_1 = ffff01a0
DQ loop=11, cmp_err_1 = ffff0180
DQ loop=10, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=10, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=10, finish count=2
byte:0, (DQS,DQ)=(a,8)
byte:1, (DQS,DQ)=(a,8)
20,data:aa
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=16666666 HZ
===================================================================
U-Boot 1.1.3 (Jun 6 2016 - 13:15:24)
Board: Ralink APSoC DRAM: 256 MB
relocate_code Pointer at: 8ffac000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe0a10
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device not found, ID: c2f1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
Env addr : 0x80000
..============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC MT7621AS (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Jun 6 2016 Time:13:15:24
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
Reset switch ...
#Reset_MT7530
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
STANDALONE_LOAD_ADDR is 0xa0600000
..Example expects ABI version 2
Actual U-Boot ABI version 2
******************************************
Uboot StandAlone Entry
******************************************
0, cmd
1, 0x0000000D
cmd : 0x0000000D
You choosed 1
0
1: System Load Linux to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.254) ==:192.168.1.254
Input server IP (192.168.1.100) ==:192.168.1.100
Input Linux Kernel filename (openwrt.bin) ==:openwrt.bin
..Erasing NAND Flash...
.Writing to NAND Flash...
done
netboot_common, argc= 3
NetTxPacket = 0x8FFE49C0
KSEG1ADDR(NetTxPacket) = 0xAFFE49C0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.100; our IP address is 192.168.1.254
Filename 'openwrt.bin'.
TIMEOUT_COUNT=10,Load address: 0x80a00000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REPLY, set server/gtwy eth addr (00:21:cc:cf:b2:37)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##############
done
Bytes transferred = 5725438 (575cfe hex)
NetBootFileXferSize= 00575cfe
Automatic boot of image at addr 0x80A00000 ...
## Booting image at 80a00000 ...
Image Name: MIPS OpenWrt Linux-5.10.146
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 5725374 Bytes = 5.5 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 5.10.146 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19803-9a599fee93) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Oct 14 22:44:41 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is SERCOMM NA502
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2} total 2
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30256 r8192 d22992 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00010898
[ 0.000000] Readback ErrCtl register=00010898
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246536K/262144K available (7026K kernel code, 631K rwdata, 828K rodata, 4172K init, 243K bss, 15608K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015860] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.033806] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.106095] pid_max: default: 32768 minimum: 301
[ 0.115401] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.129798] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.147793] rcu: Hierarchical SRCU implementation.
[ 0.157552] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.172935] smp: Bringing up secondary CPUs ...
[ 0.182503] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.182514] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.182524] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.182601] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.232816] Synchronize counters for CPU 1: done.
[ 0.292487] smp: Brought up 1 node, 2 CPUs
[ 0.304668] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.324163] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.337783] pinctrl core: initialized pinctrl subsystem
[ 0.350409] NET: Registered protocol family 16
[ 0.360336] thermal_sys: Registered thermal governor 'step_wise'
[ 0.362937] cpuidle: using governor teo
[ 0.432038] clocksource: Switched to clocksource GIC
[ 0.443660] NET: Registered protocol family 2
[ 0.452589] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.468489] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.485377] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.500569] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.514742] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.527518] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.540442] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.554700] NET: Registered protocol family 1
[ 0.563325] PCI: CLS 0 bytes, default 32
[ 4.243860] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 4.260772] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.272329] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.292582] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 4.309003] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.320462] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.331931] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.343751] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.360096] printk: console [ttyS0] disabled
[ 4.368781] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 15, base_baud = 3125000) is a 16550A
[ 4.386733] printk: console [ttyS0] enabled
[ 4.386733] printk: console [ttyS0] enabled
[ 4.403276] printk: bootconsole [early0] disabled
[ 4.403276] printk: bootconsole [early0] disabled
[ 4.422941] 1e000d00.uartlite2: ttyS1 at MMIO 0x1e000d00 (irq = 16, base_baud = 3125000) is a 16550A
[ 4.442300] 1e000e00.uartlite3: ttyS2 at MMIO 0x1e000e00 (irq = 17, base_baud = 3125000) is a 16550A
[ 4.467419] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 4.480191] nand: Macronix MX30LF1G18AC
[ 4.487881] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 4.503025] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 4.516197] 10 fixed-partitions partitions found on MTD device mt7621-nand
[ 4.531155] Creating 10 MTD partitions on "mt7621-nand":
[ 4.541805] 0x000000000000-0x000000080000 : "u-boot"
[ 4.557993] 0x000000080000-0x000000100000 : "config"
[ 4.574982] 0x000000100000-0x000000140000 : "factory"
[ 4.588591] 0x000000140000-0x000001540000 : "kernel1"
[ 4.801246] 0x000001540000-0x000001940000 : "kernel"
[ 4.852509] 0x000001940000-0x000002940000 : "ubi"
[ 5.023953] 0x000002940000-0x000002a40000 : "user_storage"
[ 5.046281] 0x000002a40000-0x000003a40000 : "data"
[ 5.218180] 0x000003a40000-0x000006c40000 : "storage"
[ 5.731610] 0x000006c40000-0x000007f80000 : "backup"
[ 5.982774] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 5.999394] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 6.016985] i2c /dev entries driver
[ 6.026081] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 6.039529] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 6.057142] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 6.073477] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 6.089930] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 6.102984] NET: Registered protocol family 10
[ 6.115132] Segment Routing with IPv6
[ 6.122635] NET: Registered protocol family 17
[ 6.131608] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 6.157740] 8021q: 802.1Q VLAN Support v1.8
[ 6.170201] gpio-export gpio-export: 2 gpio(s) exported
[ 6.180972] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 6.232840] mt7530 mdio-bus:1f lan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=26)
[ 6.254971] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 6.271838] DSA: tree 0 setup
[ 6.278141] rt2880-pinmux pinctrl: pcie is already enabled
[ 6.289187] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 6.302569] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 6.320111] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 6.336420] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 6.352813] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 6.367980] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 6.383056] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 6.497717] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 6.508833] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 6.620135] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 6.634007] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 6.643728] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 6.653448] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 6.672185] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 6.684894] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 6.698601] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 6.712305] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 6.723242] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 6.743568] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 6.755556] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 6.768044] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
[ 6.780598] pci 0000:00:00.0: supports D1
[ 6.788587] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 6.800736] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 6.812803] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 6.825318] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
[ 6.837877] pci 0000:00:01.0: supports D1
[ 6.845867] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 6.859508] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 6.871596] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 6.885653] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[ 6.898171] pci 0000:01:00.0: reg 0x30: initial BAR value 0x00000000 invalid
[ 6.912221] pci 0000:01:00.0: reg 0x30: [mem size 0x00010000 pref]
[ 6.924639] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 6.938682] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 6.949139] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 6.961280] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 6.974808] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 6.989204] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 7.002662] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 7.014695] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 7.028755] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000]
[ 7.040345] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 7.054377] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 7.064844] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 7.076983] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 7.090519] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 7.103764] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 7.116943] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 7.130819] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 7.144005] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 7.157879] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 7.171425] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 7.185826] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 7.199349] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 7.212889] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 7.226420] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 7.239944] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 7.253497] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 7.268073] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 7.282463] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 7.292359] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 7.305881] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 7.319416] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 7.333813] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 7.347342] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 7.357233] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 7.370765] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 7.388131] UBI: auto-attach mtd5
[ 7.394833] ubi0: attaching mtd5
[ 7.401664] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 7.739043] ubi0: scanning is finished
[ 7.762982] ubi0: attached mtd5 (name "ubi", size 16 MiB)
[ 7.773775] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 7.787480] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 7.801006] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 7.814872] ubi0: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
[ 7.826828] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 7.841212] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1317597552
[ 7.859432] ubi0: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20
[ 7.877829] ubi0: background thread "ubi_bgt0d" started, PID 446
[ 7.880158] block ubiblock0_0: created from ubi0:0(rootfs)
[ 7.900831] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 7.929996] Freeing unused kernel memory: 4172K
[ 7.939108] This architecture does not have kernel memory protection.
[ 7.951962] Run /init as init process
[ 8.409357] init: Console is alive
[ 8.416521] init: - watchdog -
[ 8.433364] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.455527] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.481999] init: - preinit -
[ 8.684252] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.768596] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.804240] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.038216] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 9.054456] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.062049] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[ 9.084602] 8021q: adding VLAN 0 to HW filter on device lan
[ 9.098371] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 12.263637] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.278450] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready
[ 13.248756] mt7530 mdio-bus:1f lan: Link is Down
[ 13.267433] procd: - early -
[ 13.273515] procd: - watchdog -
[ 13.871612] procd: - watchdog -
[ 13.878300] procd: - ubus -
[ 13.891062] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.942202] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.955405] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.971678] procd: - init -
Please press Enter to activate this console.
[ 14.452853] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.553659] PPP generic driver version 2.4.2
[ 14.566526] NET: Registered protocol family 24
[ 14.588085] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.680868] urngd: v1.0.2 started.
[ 14.857564] random: crng init done
[ 14.864369] random: 30 urandom warning(s) missed due to ratelimiting
[ 29.686644] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 29.723000] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 29.741725] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 29.767437] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.789948] mt7530 mdio-bus:1f lan: configuring for phy/gmii link mode
[ 29.805254] 8021q: adding VLAN 0 to HW filter on device lan
[ 29.831972] br-lan: port 1(lan) entered blocking state
[ 29.842290] br-lan: port 1(lan) entered disabled state
[ 29.854693] device lan entered promiscuous mode
[ 29.863818] device eth0 entered promiscuous mode
[ 34.181453] mt7530 mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 34.196259] br-lan: port 1(lan) entered blocking state
[ 34.206686] br-lan: port 1(lan) entered forwarding state
[ 34.219127] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Watchdog handover: fd=3
- watchdog -
Watchdog does not have CARDRESET support
Fri Oct 14 22:46:51 UTC 2022 upgrade: Sending TERM to remaining processes ...
Fri Oct 14 22:46:51 UTC 2022 upgrade: Sending signal TERM to ntpd (2287)
Fri Oct 14 22:46:51 UTC 2022 upgrade: Sending signal TERM to ntpd (2291)
Fri Oct 14 22:46:55 UTC 2022 upgrade: Sending KILL to remaining processes ...
Fri Oct 14 22:46:55 UTC 2022 upgrade: Sending signal KILL to ntpd (2287)
Fri Oct 14 22:46:55 UTC 2022 upgrade: Sending signal KILL to ntpd (2291)
[ 154.964154] stage2 (2820): drop_caches: 3
Fri Oct 14 22:47:01 UTC 2022 upgrade: Switching to ramdisk...
Fri Oct 14 22:47:04 UTC 2022 upgrade: Performing system upgrade...
Unlocking kernel ...
Writing from <stdin> to kernel ...
removing ubiblock0_0
[ 159.331579] block ubiblock0_0: released
Volume ID 0, size 31 LEBs (3936256 bytes, 3.7 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 9269248
Volume ID 1, size 73 LEBs (9269248 bytes, 8.8 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 161.451845] reboot: Restarting system===================================================================
MT7621 stage1 code 13:15:05 (ASIC)
CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xd, 1/0 = 561/463 35000000
PLL4 FB_DL: 0x14, 1/0 = 808/216 51000000
PLL2 FB_DL: 0x16, 1/0 = 727/297 59000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 32
B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
opt_dle value:11
DRAMC_R0DELDLY[018]=00001C1C
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 9 14 10 15 9 14 7 4 12
10 | 6 13 9 12 7 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =28 DQS1 = 28
==================================================================
bit DQS0 bit DQS1
0 (1~54)27 8 (1~51)26
1 (0~50)25 9 (2~50)26
2 (1~49)25 10 (1~49)25
3 (1~52)26 11 (2~52)27
4 (1~55)28 12 (1~55)28
5 (1~54)27 13 (2~52)27
6 (1~53)27 14 (2~54)28
7 (1~54)27 15 (1~54)27
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 15 12 15 12 15 10 15 8 6 14
10 | 9 14 9 13 7 12
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff2a00
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
DQS loop = 14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2
DQ loop=15, cmp_err_1 = ffff45aa
DQ loop=14, cmp_err_1 = ffff05aa
DQ loop=13, cmp_err_1 = ffff05aa
DQ loop=12, cmp_err_1 = ffff0180
DQ loop=11, cmp_err_1 = ffff0180
DQ loop=10, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=10, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=10, finish count=2
byte:0, (DQS,DQ)=(a,8)
byte:1, (DQS,DQ)=(a,8)
20,data:aa
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=16666666 HZ
===================================================================
U-Boot 1.1.3 (Jun 6 2016 - 13:15:24)
Board: Ralink APSoC DRAM: 256 MB
relocate_code Pointer at: 8ffac000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe0a10
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device not found, ID: c2f1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
Env addr : 0x80000
..============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC MT7621AS (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Jun 6 2016 Time:13:15:24
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
Reset switch ...
#Reset_MT7530
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
STANDALONE_LOAD_ADDR is 0xa0600000
..Example expects ABI version 2
Actual U-Boot ABI version 2
******************************************
Uboot StandAlone Entry
******************************************
0, cmd
1, 0x0000000D
cmd : 0x0000000D
0
Example expects ABI version 2
Actual U-Boot ABI version 2
******************************************
Uboot StandAlone Entry
******************************************
0, boot
Flash Sector Number : 522.
***************************************************
Sercomm Boot Version 2.00.1
***************************************************
Entering Firmware : Everything is OK.
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> .......................OK
Image2 Data Checksum --> ..........................................OK
Image1: OK Image2: OK
=================================================
..kernel addr :0xbfd40000
flash base: 0xbfc00000, kernel addr :0xbfd40000, bootloader size: 0x80000, config size 0x80000, fac size : 0x40000
..Erasing NAND Flash...
.Writing to NAND Flash...
done
3: System Boot system code via Flash.
## Booting image at bfd40000 ...
Image Name: OpenWrt Linux-3.10.14
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1457676 Bytes = 1.4 MB
Load Address: 80001000
Entry Point: 80001000
....................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.14 (openwrt@13bc1de213b4) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #2 SMP Thu Jun 3 12:27:31 UTC 2021
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x0bffffff]
[ 0.000000] Normal [mem 0x0c000000-0x0fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x0fffffff]
[ 0.000000] avail: cpu2 is not ready
[ 0.000000] avail: cpu3 is not ready
[ 0.000000] Detected 1 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @8c204000 s6400 r8192 d14080 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00010890
[ 0.000000] Readback ErrCtl register=00010890
[ 0.000000] Memory: 255240k/262144k available (3209k kernel code, 6904k reserved, 827k data, 244k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.132000] Calibrating delay loop... 562.17 BogoMIPS (lpj=1124352)
[ 0.164000] pid_max: default: 32768 minimum: 301
[ 0.168000] Mount-cache hash table entries: 512
[ 0.172000] launch: starting cpu1
[ 0.176000] launch: cpu1 gone!
[ 0.176000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.208000] Synchronize counters for CPU 1: done.
[ 0.216000] Brought up 2 CPUs
[ 0.220000] NET: Registered protocol family 16
[ 0.512000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.516000] PCIE PHY initialize
[ 0.520000] ***** Xtal 40MHz *****
[ 0.524000] start MT7621 PCIe register access
[ 1.100000] RALINK_RSTCTRL = 7000000
[ 1.104000] RALINK_CLKCFG1 = 77ffeff8
[ 1.108000]
[ 1.108000] *************** MT7621 PCIe RC mode *************
[ 1.588000] PCIE0 no card, disable it(RST&CLK)
[ 1.592000] pcie_link status = 0x6
[ 1.596000] RALINK_RSTCTRL= 6000000
[ 1.600000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.604000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 10207f2
[ 1.608000] PCIE1 enabled
[ 1.612000] PCIE2 enabled
[ 1.616000] interrupt enable status: 600000
[ 1.620000] Port 1 N_FTS = 1b105000
[ 1.624000] Port 0 N_FTS = 1b105000
[ 1.628000] config reg done
[ 1.632000] init_rt2880pci done
[ 1.656000] bio: create slab <bio-0> at 0
[ 1.660000] usbcore: registered new interface driver usbfs
[ 1.664000] usbcore: registered new interface driver hub
[ 1.668000] usbcore: registered new device driver usb
[ 1.672000] PCI host bridge to bus 0000:00
[ 1.676000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.680000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.684000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.688000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.692000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.696000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.700000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.704000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.708000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 1.712000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 1.716000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.720000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[ 1.724000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.728000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.732000] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 1.736000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 1.740000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.744000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 1.748000] BAR0 at slot 0 = 0
[ 1.752000] bus=0x0, slot = 0x0
[ 1.756000] res[0]->start = 0
[ 1.760000] res[0]->end = 0
[ 1.764000] res[1]->start = 60300000
[ 1.768000] res[1]->end = 6030ffff
[ 1.772000] res[2]->start = 0
[ 1.776000] res[2]->end = 0
[ 1.780000] res[3]->start = 0
[ 1.784000] res[3]->end = 0
[ 1.788000] res[4]->start = 0
[ 1.792000] res[4]->end = 0
[ 1.796000] res[5]->start = 0
[ 1.800000] res[5]->end = 0
[ 1.804000] BAR0 at slot 1 = 0
[ 1.808000] bus=0x0, slot = 0x1
[ 1.812000] res[0]->start = 0
[ 1.816000] res[0]->end = 0
[ 1.820000] res[1]->start = 60310000
[ 1.824000] res[1]->end = 6031ffff
[ 1.828000] res[2]->start = 0
[ 1.832000] res[2]->end = 0
[ 1.836000] res[3]->start = 0
[ 1.840000] res[3]->end = 0
[ 1.844000] res[4]->start = 0
[ 1.848000] res[4]->end = 0
[ 1.852000] res[5]->start = 0
[ 1.856000] res[5]->end = 0
[ 1.860000] bus=0x1, slot = 0x0, irq=0x18
[ 1.864000] res[0]->start = 60000000
[ 1.868000] res[0]->end = 600fffff
[ 1.872000] res[1]->start = 0
[ 1.876000] res[1]->end = 0
[ 1.880000] res[2]->start = 0
[ 1.884000] res[2]->end = 0
[ 1.888000] res[3]->start = 0
[ 1.892000] res[3]->end = 0
[ 1.896000] res[4]->start = 0
[ 1.900000] res[4]->end = 0
[ 1.904000] res[5]->start = 0
[ 1.908000] res[5]->end = 0
[ 1.912000] bus=0x2, slot = 0x1, irq=0x19
[ 1.916000] res[0]->start = 60200000
[ 1.920000] res[0]->end = 602fffff
[ 1.924000] res[1]->start = 0
[ 1.928000] res[1]->end = 0
[ 1.932000] res[2]->start = 0
[ 1.936000] res[2]->end = 0
[ 1.940000] res[3]->start = 0
[ 1.944000] res[3]->end = 0
[ 1.948000] res[4]->start = 0
[ 1.952000] res[4]->end = 0
[ 1.956000] res[5]->start = 0
[ 1.960000] res[5]->end = 0
[ 1.964000] Bluetooth: Core ver 2.16
[ 1.972000] NET: Registered protocol family 31
[ 1.980000] Bluetooth: HCI device and connection manager initialized
[ 1.992000] Bluetooth: HCI socket layer initialized
[ 2.000000] Bluetooth: L2CAP socket layer initialized
[ 2.012000] Bluetooth: SCO socket layer initialized
[ 2.020000] Switching to clocksource MIPS
[ 2.032000] NET: Registered protocol family 2
[ 2.036000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.052000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.064000] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.076000] TCP: reno registered
[ 2.084000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.096000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.108000] NET: Registered protocol family 1
[ 2.204000] 4 CPUs re-calibrate udelay(lpj = 1167360)
[ 2.216000] ======= sercomm_button_init =======
[ 2.224000] mt7621_register_gpio_keys_polled start!
[ 2.236000] mt7621_register_gpio_keys_polled ends!
[ 2.248000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.260000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.280000] io scheduler noop registered (default)
[ 2.288000] ======== sercomm_gpio_init ========
[ 2.296000]
[ 2.296000] led on GPIO_LED_POWER
[ 2.308000] ===== sercomm_gpio_ioctl_init =====
[ 2.320000] ====== sercomm_led_ioctl_init =====
[ 2.332000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.348000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.360000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.372000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A
[ 2.388000] Ralink APSoC Hardware Watchdog Timer
[ 2.396000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.412000] Allocate 16 byte aligned buffer: 8045d320
[ 2.420000] Enable NFI Clock
[ 2.428000] # MTK NAND # : Use HW ECC
[ 2.436000] NAND ID [C2 F1 80 95 02, 00809502]
[ 2.444000] Device not found, ID: c2f1
[ 2.452000] Not Support this Device!
[ 2.460000] chip_mode=00000001
[ 2.464000] Support this Device in MTK table! c2f1
[ 2.476000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 2.500000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.512000] Scanning device for bad blocks
[ 2.668000] Bad eraseblock 629 at 0x000004ea0000
[ 2.772000] Signature matched and data read!
[ 2.780000] load_fact_bbt success 1023
[ 2.788000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.808000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.828000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.848000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.868000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 00
[ 2.888000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.908000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.924000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 2.944000] Creating 10 MTD partitions on "MT7621-NAND":
[ 2.956000] 0x000000000000-0x000007f80000 : "ALL"
[ 2.968000] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.980000] 0x000000080000-0x000000100000 : "Config"
[ 2.988000] 0x000000100000-0x000000140000 : "Factory"
[ 3.000000] 0x000000140000-0x000001540000 : "Firmware1"
[ 3.016000] 0x0000002a3e4c-0x000001540000 : "rootfs"
[ 3.024000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 3.064000] mtd: partition "rootfs_data" created automatically, ofs=0xec0000, len=0x680000
[ 3.080000] 0x000000ec0000-0x000001540000 : "rootfs_data"
[ 3.092000] 0x000001540000-0x000002940000 : "Firmware2"
[ 3.104000] 0x000002940000-0x000002a40000 : "user_storage"
[ 3.116000] 0x000002a40000-0x000003a40000 : "data"
[ 3.124000] 0x000003a40000-0x000006c40000 : "storage"
[ 3.136000] 0x000006c40000-0x000007f80000 : "backup"
[ 3.148000] [mtk_nand] probe successfully!
[ 3.156000] rootfs = 2a3e4c to ec0000
[ 3.164000] rdm_major = 253
[ 3.168000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 3.176000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 3.184000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 3.204000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 3.212000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 3.224000] PROC INIT OK!
[ 3.228000] *****run project phy.
[ 3.244000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.260000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.276000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.292000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.308000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.324000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.340000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.356000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.372000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.388000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.420000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.436000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.452000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.468000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.484000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.500000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.516000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.532000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.548000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.564000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 3.692000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 3.700000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[ 3.716000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000
[ 3.728000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.740000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.756000] usb usb1: Product: xHCI Host Controller
[ 3.764000] usb usb1: Manufacturer: Linux 3.10.14 xhci-hcd
[ 3.776000] usb usb1: SerialNumber: xhci-hcd
[ 3.784000] hub 1-0:1.0: USB hub found
[ 3.792000] hub 1-0:1.0: 2 ports detected
[ 3.800000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 3.812000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[ 3.824000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 3.840000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.852000] usb usb2: Product: xHCI Host Controller
[ 3.864000] usb usb2: Manufacturer: Linux 3.10.14 xhci-hcd
[ 3.872000] usb usb2: SerialNumber: xhci-hcd
[ 3.884000] hub 2-0:1.0: USB hub found
[ 3.892000] hub 2-0:1.0: 1 port detected
[ 3.900000] usbcore: registered new interface driver usbserial
[ 3.912000] usbcore: registered new interface driver usbserial_generic
[ 3.924000] usbserial: USB Serial support registered for generic
[ 3.936000] usbcore: registered new interface driver cp210x
[ 3.948000] usbserial: USB Serial support registered for cp210x
[ 3.960000] usbcore: registered new interface driver usb_debug
[ 3.972000] usbserial: USB Serial support registered for debug
[ 3.984000] usbcore: registered new interface driver ftdi_sio
[ 3.996000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 4.008000] usbcore: registered new interface driver pl2303
[ 4.020000] usbserial: USB Serial support registered for pl2303
[ 4.032000] TCP: cubic registered
[ 4.040000] NET: Registered protocol family 10
[ 4.048000] NET: Registered protocol family 17
[ 4.060000] Bluetooth: RFCOMM TTY layer initialized
[ 4.068000] Bluetooth: RFCOMM socket layer initialized
[ 4.080000] Bluetooth: RFCOMM ver 1.11
[ 4.084000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.096000] Bluetooth: BNEP filters: protocol multicast
[ 4.108000] Bluetooth: BNEP socket layer initialized
[ 4.116000] 8021q: 802.1Q VLAN Support v1.8
[ 4.132000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 4.148000] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 4.148000] Freeing unused kernel memory: 244K (803f3000 - 80430000)
[ 4.188000] usb 1-2: New USB device found, idVendor=0e8d, idProduct=7662
[ 4.200000] usb 1-2: New USB device strings: Mfr=4, Product=5, SerialNumber=6
[ 4.216000] usb 1-2: Product: Wireless
[ 4.224000] usb 1-2: Manufacturer: MediaTek Inc.
[ 4.232000] usb 1-2: SerialNumber: 000000000
[ 4.240000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 3, maxp 16, interval 1, burst 0, mult 0, ep 0x8fe48580, ep_ctx 0xbbc05080, sch_ep 0x8fe51c80
[ 4.272000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8fe485ac, ep_ctx 0xbbc050c0, sch_ep 0x8fe51a00
[ 4.300000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 2, maxp 512, interval 1, burst 0, mult 0, ep 0x8fe485d8, ep_ctx 0xbbc050a0, sch_ep 0x8fe51780
[ 4.328000] add_ep parameters, dev_speed 3, is_in 1, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8fe2dd80, ep_ctx 0xbbc05100, sch_ep 0x8fe51580
[ 4.356000] add_ep parameters, dev_speed 3, is_in 0, isTT 0, ep_type 1, maxp 0, interval 8, burst 0, mult 0, ep 0x8fe2ddac, ep_ctx 0xbbc050e0, sch_ep 0x8fe51300
[ 4.388000]
[ 4.388000]
[ 4.388000] Unsupported Device!
[ 4.388000] Vendor=e8d ProdID=7662
[ 4.388000] Manufacturer=MediaTek Inc. Product=Wireless
[ 4.388000]
procd: Console i[ 4.552000] Started WatchDog Timer.
s alive
procd: - watchdog started -
procd: - watchdog fd closed -
[ 5.332000] Button Hotplug driver version 0.4.1
[ 5.348000] SCSI subsystem initialized
[ 5.364000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 5.852000] 3C:FFFFFF98:72:FFFFFFF5:FFFFFF9B:10
[ 5.864000] Raeth v3.1 (Tasklet)
[ 5.876000] phy_free_head is 0x1bc1e000!!!
[ 5.884000] phy_free_tail_phy is 0x1bc1fff0!!!
[ 5.892000] txd_pool=bbc20000 phy_txd_pool=1BC20000
[ 5.900000] ei_local->skb_free start address is 0x8fe326dc.
[ 5.912000] free_txd: 1bc20010, ei_local->cpu_ptr: 1BC20000
[ 5.924000] POOL HEAD_PTR | DMA_PTR | CPU_PTR
[ 5.932000] ----------------+---------+--------
[ 5.940000] 0xbbc20000 0x1BC20000 0x1BC20000
[ 5.952000]
[ 5.952000] phy_qrx_ring = 0x1bc12000, qrx_ring = 0xbbc12000
[ 5.968000]
[ 5.968000] phy_rx_ring0 = 0x1bc28000, rx_ring0 = 0xbbc28000
[ 6.004000] MT7530 Reset Completed!!
[ 6.012000] change HW-TRAP to 0x17ccf
[ 6.020000] set LAN/WAN LLLLW
[ 6.028000] GMAC1_MAC_ADRH -- : 0x00003c98
[ 6.040000] GMAC1_MAC_ADRL -- : 0x72f59b10
[ 6.052000] CDMA_CSG_CFG = 81000000
[ 6.060000] GDMA1_FWD_CFG = 20710000
[ 6.572000] block: attempting to load /etc/config/fstab
[ 6.632000] block: extroot: not configured
jffs2 is ready
jffs2 is ready
[ 6.792000] jffs2: notice: (308) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 7.168000] block: attempting to load /etc/config/fstab
[ 7.180000] block: extroot: not configured
switching to overlay
[ 7.204000] ra2880stop()...Done
[ 7.212000] Free TX/RX Ring Memory!
procd: - early -
procd: - ubus -
procd: - init -
### Set BLE Power Level 5 ###
### Set BLE MAC Address ###
[ 12.384000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 12.400000] tun: Universal TUN/TAP device driver, 1.6
[ 12.408000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.428000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.436000] Type=Restricted Cone
[ 12.448000] nf_conntrack version 0.5.0 (3991 buckets, 15964 max)
[ 12.464000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.488000] usbcore: registered new interface driver btusb
[ 12.504000] usbcore: registered new interface driver cdc_acm
[ 12.516000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 12.612000] xt_time: kernel timezone is -0000
[ 12.624000] usbcore: registered new interface driver cdc_ether
[ 12.644000] usbcore: registered new interface driver option
[ 12.652000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 12.672000] PPP generic driver version 2.4.2
[ 12.680000] NET: Registered protocol family 24
procd: - init complete -