[ 0.000000] Linux version 5.4.154 (aashish@neil) (gcc version 8.4.0 (OpenWrt1
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is MikroTik RouterBOARD M33G
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 576 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jf2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, )
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, li)
[ 0.000000] Writing ErrCtl register=0004000a
[ 0.000000] Readback ErrCtl register=0004000a
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 250412K/262144K available (5974K kernel code, 202K rwdat)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x36c/0x584 wi0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478as
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_s
[ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880s
[ 0.007803] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.042005] pid_max: default: 32768 minimum: 301
[ 0.046779] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, line)
[ 0.054004] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes,)
[ 0.064438] rcu: Hierarchical SRCU implementation.
[ 0.069875] smp: Bringing up secondary CPUs ...
[ 1.565108] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 1.565119] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys
[ 1.565131] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 1.565233] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.102639] Synchronize counters for CPU 1: done.
[ 7.679854] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 7.679863] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys
[ 7.679871] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 7.679927] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.167341] Synchronize counters for CPU 2: done.
[ 8.944591] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.944599] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bys
[ 8.944606] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.944667] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.225204] Synchronize counters for CPU 3: done.
[ 0.255088] smp: Brought up 1 node, 4 CPUs
[ 0.263551] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.273248] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.280316] pinctrl core: initialized pinctrl subsystem
[ 0.286989] NET: Registered protocol family 16
[ 0.304771] FPU Affinity set after 4688 emulations
[ 0.320909] workqueue: max_active 576 requested for napi_workq is out of ran2
[ 0.332092] clocksource: Switched to clocksource GIC
[ 0.338826] NET: Registered protocol family 2
[ 0.343333] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linea)
[ 0.351432] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144)
[ 0.359762] TCP established hash table entries: 2048 (order: 1, 8192 bytes, )
[ 0.367358] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.374446] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.380877] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.387354] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.394532] NET: Registered protocol family 1
[ 0.398847] PCI: CLS 0 bytes, default 32
[ 0.492035] 4 CPUs re-calibrate udelay(lpj = 1167360)
[ 0.498773] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.506646] random: fast init done
[ 0.520469] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.526242] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[ 0.538900] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.544738] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.550601] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.557051] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.564825] printk: console [ttyS0] disabled
[ 0.569119] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baudA
[ 0.578103] printk: console [ttyS0] enabled
[ 0.586359] printk: bootconsole [early0] disabled
[ 0.598614] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.615284] spi-nor spi0.0: w25x40 (512 Kbytes)
[ 0.619872] 1 fixed-partitions partitions found on MTD device spi0.0
[ 0.626220] Creating 1 MTD partitions on "spi0.0":
[ 0.631027] 0x000000000000-0x000000040000 : "RouterBoot"
[ 0.638689] 5 routerbootpart partitions found on MTD device RouterBoot
[ 0.645247] Creating 5 MTD partitions on "RouterBoot":
[ 0.650392] 0x000000000000-0x00000000f000 : "bootloader1"
[ 0.656992] 0x00000000f000-0x000000010000 : "hard_config"
[ 0.663495] 0x000000010000-0x00000001f000 : "bootloader2"
[ 0.669998] 0x000000020000-0x000000021000 : "soft_config"
[ 0.676600] 0x000000030000-0x000000031000 : "bios"
[ 0.692150] spi-nor spi0.1: w25q128jv (16384 Kbytes)
[ 0.697162] 1 fixed-partitions partitions found on MTD device spi0.1
[ 0.703500] Creating 1 MTD partitions on "spi0.1":
[ 0.708301] 0x000000040000-0x000001000000 : "firmware"
[ 0.715282] 2 minor-fw partitions found on MTD device firmware
[ 0.721166] Creating 2 MTD partitions on "firmware":
[ 0.726144] 0x000000000000-0x000000280000 : "kernel"
[ 0.732391] 0x000000280000-0x000000fc0000 : "rootfs"
[ 0.738530] mtd: device 8 (rootfs) set to be root filesystem
[ 0.744302] 1 squashfs-split partitions found on MTD device rootfs
[ 0.750486] 0x0000007d0000-0x000000fc0000 : "rootfs_data"
[ 0.758158] libphy: Fixed MDIO Bus: probed
[ 0.786492] libphy: mdio: probed
[ 0.789974] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.798644] mtk_soc_eth 1e100000.ethernet: generated random MAC address 1e:3c
[ 0.807747] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xb2
[ 0.817219] i2c-mt7621 1e000900.i2c: clock 100 kHz
[ 0.823448] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 0.831247] MikroTik RouterBOARD hardware configuration sysfs driver v0.06
[ 0.839577] MikroTik RouterBOARD software configuration sysfs driver v0.03
[ 0.847840] NET: Registered protocol family 10
[ 0.853723] Segment Routing with IPv6
[ 0.857525] NET: Registered protocol family 17
[ 0.862305] 8021q: 802.1Q VLAN Support v1.8
[ 0.870573] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.886507] libphy: dsa slave smi: probed
[ 0.890946] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver ]
[ 0.900666] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:01] driver]
[ 0.910336] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver]
[ 0.920524] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 0.931726] DSA: tree 0 setup
[ 0.935054] rt2880-pinmux pinctrl: pcie is already enabled
[ 0.940703] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port )
[ 0.948283] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port )
[ 1.055840] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.061425] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.167090] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 1.174042] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.180998] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.185882] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000,2
[ 1.195337] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.201707] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.208578] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.215448] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.220971] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.227007] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.233273] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.239618] pci 0000:00:00.0: supports D1
[ 1.243629] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.250901] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reg
[ 1.259158] pci 0000:01:00.0: [10ec:8178] type 00 class 0x028000
[ 1.265225] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 1.270820] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit]
[ 1.277730] pci 0000:01:00.0: supports D1 D2
[ 1.282004] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.290086] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.295332] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.301423] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.308208] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pre]
[ 1.315428] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.322075] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.328684] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.335643] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.342428] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pre]
[ 1.349646] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 1.356437] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.363230] pci 0000:01:00.0: BAR 2: assigned [mem 0x60000000-0x60003fff 64b]
[ 1.370543] pci 0000:01:00.0: BAR 0: assigned [io 0x1e160000-0x1e1600ff]
[ 1.377338] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.382305] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.389087] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.395868] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pre]
[ 1.403614] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 1.404843] hctosys: unable to open rtc device (rtc0)
[ 1.421327] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[ 1.432678] Freeing unused kernel memory: 1244K
[ 1.437222] This architecture does not have kernel memory protection.
[ 1.443641] Run /sbin/init as init process
[ 1.934259] init: Console is alive
[ 1.937925] init: - watchdog -
[ 3.150230] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.300729] usbcore: registered new interface driver usbfs
[ 3.306346] usbcore: registered new interface driver hub
[ 3.311783] usbcore: registered new device driver usb
[ 3.327226] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, usir
[ 3.335976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, ur
[ 3.344962] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.350298] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus num1
[ 3.364219] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 q0
[ 3.373430] xhci-mtk 1e1c0000.xhci: irq 21, io mem 0x1e1c0000
[ 3.379431] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.384766] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus num2
[ 3.392243] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 3.399649] hub 1-0:1.0: USB hub found
[ 3.403504] hub 1-0:1.0: 2 ports detected
[ 3.408436] usb usb2: We don't know the algorithms for LPM for this host, di.
[ 3.417462] hub 2-0:1.0: USB hub found
[ 3.421321] hub 2-0:1.0: 1 port detected
[ 3.431308] kmodloader: done loading kernel modules from /etc/modules-boot.d*
[ 3.440431] init: - preinit -
[ 4.266190] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii e
[ 4.274518] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flx
[ 4.282987] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4.454871] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.566577] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.631769] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.854140] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 4.861150] 8021q: adding VLAN 0 to HW filter on device lan1
[ 7.932587] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control x
[ 7.940109] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 9.114003] jffs2: notice: (599) jffs2_build_xattr_subsystem: complete build.
[ 9.131174] mount_root: overlay filesystem has not been fully initialized yet
[ 9.139018] mount_root: switching to jffs2 overlay
[ 9.147541] overlayfs: upper fs does not support tmpfile.
[ 9.156472] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 9.217956] mt7530 mdio-bus:1f lan1: Link is Down
[ 9.232828] procd: - early -
[ 9.235805] procd: - watchdog -
[ 9.820259] procd: - watchdog -
[ 9.898245] procd: - ubus -
[ 9.995878] procd: - init -
[ 10.681655] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.767005] random: crng init done
[ 10.770412] random: 7 urandom warning(s) missed due to ratelimiting
[ 10.786262] NET: Registered protocol family 15
[ 10.793801] Initializing XFRM netlink socket
[ 10.814938] l2tp_core: L2TP core driver, V2.0
[ 10.820766] l2tp_netlink: L2TP netlink interface
[ 10.823431] urngd: v1.0.2 started.
[ 10.839452] GACT probability on
[ 10.843907] Mirror/redirect action on
[ 10.857373] u32 classifier
[ 10.860168] input device check on
[ 10.863812] Actions configured
[ 10.880537] usbcore: registered new interface driver cdc_wdm
[ 10.887168] Loading modules backported from Linux version v5.10.68-0-g4d85245
[ 10.894739] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[ 10.925857] usbcore: registered new interface driver usbserial_generic
[ 10.932694] usbserial: USB Serial support registered for generic
[ 10.958548] xt_time: kernel timezone is -0000
[ 11.077853] PPP generic driver version 2.4.2
[ 11.084020] NET: Registered protocol family 24
[ 11.090948] usbcore: registered new interface driver qmi_wwan
[ 11.123042] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 11.134542] usbcore: registered new interface driver option
[ 11.140283] usbserial: USB Serial support registered for GSM modem (1-port)
[ 11.164183] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=25
[ 11.169620] pci 0000:00:00.0: enabling device (0004 -> 0007)
[ 11.175277] rtl8192ce 0000:01:00.0: enabling device (0000 -> 0003)
[ 11.181652] rtl8192ce: Chip Version ID: B_CHIP_92C
[ 11.195846] rtl8192ce: Using firmware rtlwifi/rtl8192cfw.bin
[ 11.207721] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 11.211767] rtlwifi: rtlwifi: wireless switch is on
[ 11.223683] usbcore: registered new interface driver rtl8192cu
[ 11.244174] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 40.966333] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 40.983098] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii e
[ 40.991513] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flx
[ 40.994963] device eth0 entered promiscuous mode
[ 41.005244] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 41.012597] 8021q: adding VLAN 0 to HW filter on device lan1
[ 41.021467] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.028771] br-lan: port 1(lan1) entered blocking state
[ 41.034111] br-lan: port 1(lan1) entered disabled state
[ 41.040646] device lan1 entered promiscuous mode
[ 41.069259] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 41.076890] 8021q: adding VLAN 0 to HW filter on device lan2
[ 41.086807] br-lan: port 2(lan2) entered blocking state
[ 41.092123] br-lan: port 2(lan2) entered disabled state
[ 41.099108] device lan2 entered promiscuous mode
[ 41.125827] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 41.133006] 8021q: adding VLAN 0 to HW filter on device wan
[ 44.092594] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control x
[ 44.100145] br-lan: port 1(lan1) entered blocking state
[ 44.105387] br-lan: port 1(lan1) entered forwarding state
[ 44.112195] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 286.220090] rcu: INFO: rcu_sched self-detected stall on CPU
[ 286.225667] rcu: 0-....: (14998 ticks this GP) idle=52e/1/0x40000002 sof
[ 286.234494] (t=15000 jiffies g=10329 q=1078)
[ 286.238829] NMI backtrace for cpu 0
[ 286.242304] CPU: 0 PID: 1686 Comm: hostapd Not tainted 5.4.154 #0
[ 286.248365] Stack : 80720000 8007e130 806e0000 806e0e9c 80740000 806e0e64 80c
[ 286.256686] 80880000 8fdb7428 8072ad63 80673820 00000000 00000001 8fc
[ 286.265005] 00000000 00000000 808c0000 00000000 30232034 0000011e 2e4
[ 286.273323] 00000000 0000000e 00000000 0003b280 80000000 80740000 000
[ 286.281641] 806676fc 807282d0 80730000 00000000 00000000 80351594 000
[ 286.289959] ...
[ 286.292391] Call Trace:
[ 286.294850] [<8000b64c>] show_stack+0x30/0x100
[ 286.299290] [<805b4be0>] dump_stack+0xa4/0xdc
[ 286.303639] [<805bb044>] nmi_cpu_backtrace+0xe4/0x134
[ 286.308668] [<805bb1f0>] nmi_trigger_cpumask_backtrace+0x15c/0x194
[ 286.314840] [<8008df14>] rcu_dump_cpu_stacks+0xe0/0x12c
[ 286.320047] [<80092b94>] rcu_sched_clock_irq+0x6e0/0x948
[ 286.325347] [<80097e38>] update_process_times+0x2c/0x78
[ 286.330568] [<800aa3ec>] tick_handle_periodic+0x34/0xd0
[ 286.335795] [<803e6cb4>] gic_compare_interrupt+0x7c/0x9c
[ 286.341083] [<800854a4>] handle_percpu_devid_irq+0xbc/0x19c
[ 286.346643] [<8007f354>] generic_handle_irq+0x40/0x58
[ 286.351680] [<802f1fe0>] gic_handle_local_int+0x98/0x120
[ 286.356967] [<802f222c>] gic_irq_dispatch+0x10/0x20
[ 286.361822] [<8007f354>] generic_handle_irq+0x40/0x58
[ 286.366862] [<805d5574>] do_IRQ+0x1c/0x2c
[ 286.370855] [<802f1a88>] plat_irq_dispatch+0x64/0x104
[ 286.375885] [<80006d08>] except_vec_vi_end+0xb8/0xc4
[ 286.380835] [<8e5f8054>] 0x8e5f8054
[ 466.232111] rcu: INFO: rcu_sched self-detected stall on CPU
[ 466.237691] rcu: 0-....: (60001 ticks this GP) idle=52e/1/0x40000002 sof
[ 466.246605] (t=60003 jiffies g=10329 q=1177)
[ 466.250940] NMI backtrace for cpu 0
[ 466.254415] CPU: 0 PID: 1686 Comm: hostapd Not tainted 5.4.154 #0
[ 466.260475] Stack : 80720000 8007e130 806e0000 806e0e9c 80740000 806e0e64 80c
[ 466.268797] 80880000 8fdb7428 8072ad63 80673820 00000000 00000001 8fc
[ 466.277115] 00000000 00000000 808c0000 00000000 30232034 0000013c 2e4
[ 466.285433] 00000000 00000017 00000000 0003e1cf 80000000 80740000 000
[ 466.293751] 806676fc 807282d0 80730000 00000000 00000000 80351594 000
[ 466.302070] ...
[ 466.304503] Call Trace:
[ 466.306961] [<8000b64c>] show_stack+0x30/0x100
[ 466.311401] [<805b4be0>] dump_stack+0xa4/0xdc
[ 466.315751] [<805bb044>] nmi_cpu_backtrace+0xe4/0x134
[ 466.320780] [<805bb1f0>] nmi_trigger_cpumask_backtrace+0x15c/0x194
[ 466.326951] [<8008df14>] rcu_dump_cpu_stacks+0xe0/0x12c
[ 466.332158] [<80092b94>] rcu_sched_clock_irq+0x6e0/0x948
[ 466.337459] [<80097e38>] update_process_times+0x2c/0x78
[ 466.342679] [<800aa3ec>] tick_handle_periodic+0x34/0xd0
[ 466.347907] [<803e6cb4>] gic_compare_interrupt+0x7c/0x9c
[ 466.353194] [<800854a4>] handle_percpu_devid_irq+0xbc/0x19c
[ 466.358756] [<8007f354>] generic_handle_irq+0x40/0x58
[ 466.363791] [<802f1fe0>] gic_handle_local_int+0x98/0x120
[ 466.369078] [<802f222c>] gic_irq_dispatch+0x10/0x20
[ 466.373934] [<8007f354>] generic_handle_irq+0x40/0x58
[ 466.378973] [<805d5574>] do_IRQ+0x1c/0x2c
[ 466.382965] [<802f1a88>] plat_irq_dispatch+0x64/0x104
[ 466.387995] [<80006d08>] except_vec_vi_end+0xb8/0xc4
[ 466.392945] [<8e5f8054>] 0x8e5f8054