Random Reboots (Kernel log enclosed)

Scope · December 23, 2024, 1:42pm

R7800 running KONG 23 r0+24150-7be426a405 / LuCI openwrt-23.05 branch git-24.264.56413-c7a3562

I've been having random restarts/reboots recently, but nothing in the log (it restarts on power down/up)..

However over the last couple of days I've had a couple of these in the kernel tab, and was wondering what they were:

Kernel Log

[23/12/2024 04:05:33] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[23/12/2024 04:05:33] rcu: 0-...!: (0 ticks this GP) idle=ffa/0/0x0 softirq=7683743/7683743 fqs=0 (false positive?)
[23/12/2024 04:05:33] (detected by 1, t=2102 jiffies, g=12539193, q=306)
[23/12/2024 04:05:33] Sending NMI from CPU 1 to CPUs 0:
[23/12/2024 04:05:33] NMI backtrace for cpu 0
[23/12/2024 04:05:33] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.167 #0
[23/12/2024 04:05:33] Hardware name: Generic DT based system
[23/12/2024 04:05:33] PC is at arch_cpu_idle+0x38/0x3c
[23/12/2024 04:05:33] LR is at arch_cpu_idle+0x34/0x3c
[23/12/2024 04:05:33] pc : [] lr : [] psr: 60000013
[23/12/2024 04:05:33] sp : c0d01f60 ip : c0d05008 fp : c0d04f98
[23/12/2024 04:05:33] r10: c0d04f08 r9 : ffffe000 r8 : 00000000
[23/12/2024 04:05:33] r7 : 00000000 r6 : c0d00000 r5 : c0d04f68 r4 : 00000000
[23/12/2024 04:05:33] r3 : c0316740 r2 : 00000001 r1 : 00000000 r0 : acc1b0b2
[23/12/2024 04:05:33] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[23/12/2024 04:05:33] Control: 10c5787d Table: 46cb006a DAC: 00000051
[23/12/2024 04:05:33] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.167 #0
[23/12/2024 04:05:33] Hardware name: Generic DT based system
[23/12/2024 04:05:33] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[23/12/2024 04:05:33] [] (show_stack) from [] (dump_stack_lvl+0x40/0x4c)
[23/12/2024 04:05:33] [] (dump_stack_lvl) from [] (nmi_cpu_backtrace+0xc4/0x110)
[23/12/2024 04:05:33] [] (nmi_cpu_backtrace) from [] (do_handle_IPI+0x5c/0x12c)
[23/12/2024 04:05:33] [] (do_handle_IPI) from [] (ipi_handler+0x18/0x20)
[23/12/2024 04:05:33] [] (ipi_handler) from [] (handle_percpu_devid_irq+0x78/0x13c)
[23/12/2024 04:05:33] [] (handle_percpu_devid_irq) from [] (handle_domain_irq+0x5c/0x78)
[23/12/2024 04:05:33] [] (handle_domain_irq) from [] (gic_handle_irq+0x7c/0x90)
[23/12/2024 04:05:33] [] (gic_handle_irq) from [] (__irq_svc+0x5c/0x78)
[23/12/2024 04:05:33] Exception stack(0xc0d01f10 to 0xc0d01f58)
[23/12/2024 04:05:33] 1f00: acc1b0b2 00000000 00000001 c0316740
[23/12/2024 04:05:33] 1f20: 00000000 c0d04f68 c0d00000 00000000 00000000 ffffe000 c0d04f08 c0d04f98
[23/12/2024 04:05:33] 1f40: c0d05008 c0d01f60 c0306f18 c0306f1c 60000013 ffffffff
[23/12/2024 04:05:33] [] (__irq_svc) from [] (arch_cpu_idle+0x38/0x3c)
[23/12/2024 04:05:33] [] (arch_cpu_idle) from [] (do_idle+0x23c/0x29c)
[23/12/2024 04:05:33] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c)
[23/12/2024 04:05:33] [] (cpu_startup_entry) from [] (start_kernel+0x6b4/0x6c4)
[23/12/2024 04:05:33] rcu: rcu_sched kthread timer wakeup didn't happen for 2103 jiffies! g12539193 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
[23/12/2024 04:05:34] rcu: Possible timer handling issue on cpu=0 timer-softirq=8471914
[23/12/2024 04:05:34] rcu: rcu_sched kthread starved for 2126 jiffies! g12539193 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
[23/12/2024 04:05:34] rcu: Unless rcu_sched kthread gets sufficient CPU time, OOM is now expected behavior.
[23/12/2024 04:05:34] rcu: RCU grace-period kthread stack dump:
[23/12/2024 04:05:34] task:rcu_sched state:I stack: 0 pid: 12 ppid: 2 flags:0x00000000
[23/12/2024 04:05:34] [] (__schedule) from [] (schedule+0x74/0xcc)
[23/12/2024 04:05:34] [] (schedule) from [] (schedule_timeout+0x70/0xd0)
[23/12/2024 04:05:34] [] (schedule_timeout) from [] (rcu_gp_fqs_loop+0xf8/0x3e8)
[23/12/2024 04:05:34] [] (rcu_gp_fqs_loop) from [] (rcu_gp_kthread+0xb4/0x138)
[23/12/2024 04:05:34] [] (rcu_gp_kthread) from [] (kthread+0x128/0x144)
[23/12/2024 04:05:34] [] (kthread) from [] (ret_from_fork+0x14/0x20)
[23/12/2024 04:05:34] Exception stack(0xc146dfb0 to 0xc146dff8)
[23/12/2024 04:05:34] dfa0: 00000000 00000000 00000000 00000000
[23/12/2024 04:05:34] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[23/12/2024 04:05:34] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
[23/12/2024 04:05:34] rcu: Stack dump where RCU GP kthread last ran:
[23/12/2024 04:05:34] Sending NMI from CPU 1 to CPUs 0:
[23/12/2024 04:05:34] NMI backtrace for cpu 0
[23/12/2024 04:05:34] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.167 #0
[23/12/2024 04:05:34] Hardware name: Generic DT based system
[23/12/2024 04:05:34] PC is at arch_cpu_idle+0x38/0x3c
[23/12/2024 04:05:34] LR is at arch_cpu_idle+0x34/0x3c
[23/12/2024 04:05:34] pc : [] lr : [] psr: 60000013
[23/12/2024 04:05:34] sp : c0d01f60 ip : c0d05008 fp : c0d04f98
[23/12/2024 04:05:34] r10: c0d04f08 r9 : ffffe000 r8 : 00000000
[23/12/2024 04:05:34] r7 : 00000000 r6 : c0d00000 r5 : c0d04f68 r4 : 00000000
[23/12/2024 04:05:34] r3 : c0316740 r2 : 00000001 r1 : 00000000 r0 : acc1bc42
[23/12/2024 04:05:34] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[23/12/2024 04:05:34] Control: 10c5787d Table: 46cb006a DAC: 00000051
[23/12/2024 04:05:34] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.167 #0
[23/12/2024 04:05:34] Hardware name: Generic DT based system
[23/12/2024 04:05:34] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[23/12/2024 04:05:34] [] (show_stack) from [] (dump_stack_lvl+0x40/0x4c)
[23/12/2024 04:05:34] [] (dump_stack_lvl) from [] (nmi_cpu_backtrace+0xc4/0x110)
[23/12/2024 04:05:34] [] (nmi_cpu_backtrace) from [] (do_handle_IPI+0x5c/0x12c)
[23/12/2024 04:05:34] [] (do_handle_IPI) from [] (ipi_handler+0x18/0x20)
[23/12/2024 04:05:34] [] (ipi_handler) from [] (handle_percpu_devid_irq+0x78/0x13c)
[23/12/2024 04:05:34] [] (handle_percpu_devid_irq) from [] (handle_domain_irq+0x5c/0x78)
[23/12/2024 04:05:34] [] (handle_domain_irq) from [] (gic_handle_irq+0x7c/0x90)
[23/12/2024 04:05:34] [] (gic_handle_irq) from [] (__irq_svc+0x5c/0x78)
[23/12/2024 04:05:34] Exception stack(0xc0d01f10 to 0xc0d01f58)
[23/12/2024 04:05:34] 1f00: acc1bc42 00000000 00000001 c0316740
[23/12/2024 04:05:34] 1f20: 00000000 c0d04f68 c0d00000 00000000 00000000 ffffe000 c0d04f08 c0d04f98
[23/12/2024 04:05:34] 1f40: c0d05008 c0d01f60 c0306f18 c0306f1c 60000013 ffffffff
[23/12/2024 04:05:34] [] (__irq_svc) from [] (arch_cpu_idle+0x38/0x3c)
[23/12/2024 04:05:34] [] (arch_cpu_idle) from [] (do_idle+0x23c/0x29c)
[23/12/2024 04:05:34] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c)
[23/12/2024 04:05:34] [] (cpu_startup_entry) from [] (start_kernel+0x6b4/0x6c4)
[23/12/2024 04:05:34] ath10k_pci 0000:01:00.0: SWBA overrun on vdev 1, skipped old beacon

egc · December 23, 2024, 2:01pm

Are you using on demand governor ?

for CPUGOV in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do echo "$(cat $CPUGOV)"; done

If so set to performance:

for CPUGOV in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do [ -f $CPUGOV ] || continue; echo -n performance > $CPUGOV; done

brada4 · December 23, 2024, 2:01pm

Do you encounter any problems with normal OpenWRT?
NMI usually is sent on hardware damage, like running out of thermal envelope, or unplugging "hot" pci cards.

brada4 · December 23, 2024, 2:02pm

echo performace | tee -a /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor

Scope · December 23, 2024, 2:19pm

Looks like it is already set to Performance

root@R7800:~# for CPUGOV in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do echo "$(cat $CPUGOV)"; done
performance
performance

Scope · December 23, 2024, 2:20pm

I've only ever ran the Kong build.. Prior to OpenWRT I've been running DD-WRT on this unit happily for a few years.

I am waiting for the release of 24.10 to upgrade to that and see if that improves anything.

frollic · December 23, 2024, 2:37pm

Try the vanilla R7800 image, just to rule out a hw issue.

Scope · December 25, 2024, 11:21pm

I have upgraded to 24.10 RC4 and get the following in the kernel log, not sure if it is related to the above errors I were seeing in 23.05, what do you think?

Kernel Log 24.10

[   45.466828] ------------[ cut here ]------------
[   45.477886] WARNING: CPU: 0 PID: 1118 at backports-6.11.2/net/mac80211/main.c:272 0xbf208888 [mac80211@ee4ab5fc+0x77000]
[   45.482527] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath10k_pci(O) ath10k_core(O) ath(O) pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211(O) cfg80211(O) slhc nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c crc_ccitt compat(O) ledtrig_usbport sha512_arm seqiv geniv cmac leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_ipq806x_usb ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod scsi_common ehci_hcd ramoops reed_solomon pstore gpio_button_hotplug(O) crc32c_generic
[   45.546334] CPU: 0 PID: 1118 Comm: hostapd Tainted: G        W  O       6.6.67 #0
[   45.568425] Hardware name: Generic DT based system
[   45.575892] Function entered at [<c030d7e8>] from [<c0308f50>]
[   45.580577] Function entered at [<c0308f50>] from [<c0a5f6cc>]
[   45.586394] Function entered at [<c0a5f6cc>] from [<c031d364>]
[   45.592210] Function entered at [<c031d364>] from [<c031d4e4>]
[   45.598025] Function entered at [<c031d4e4>] from [<bf208888>]
[   45.603843] Function entered at [<bf208888>] from [<bf2089dc>]
[   45.609656] Function entered at [<bf2089dc>] from [<c08792c0>]
[   45.615474] Function entered at [<c08792c0>] from [<c0879724>]
[   45.621289] Function entered at [<c0879724>] from [<c08797bc>]
[   45.627103] Function entered at [<c08797bc>] from [<c094943c>]
[   45.632921] Function entered at [<c094943c>] from [<c094bc94>]
[   45.638736] Function entered at [<c094bc94>] from [<c084b678>]
[   45.644552] Function entered at [<c084b678>] from [<c04c581c>]
[   45.650369] Function entered at [<c04c581c>] from [<c0300060>]
[   45.656183] Exception stack(0xc349ffa8 to 0xc349fff0)
[   45.662001] ffa0:                   00000010 beef3848 00000010 00008914 beef3848 beef3838
[   45.667127] ffc0: 00000010 beef3848 00000010 00000036 00000001 00000001 00000000 00000020
[   45.675286] ffe0: b6fd2f74 beef3708 00487f44 b6f8b704
[   45.683655] ---[ end trace 0000000000000000 ]---
[   45.690823] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[   45.693170] br-lan: port 6(Traadloes-5Ghz) entered disabled state
[   45.699264] ath10k_pci 0000:01:00.0 Traadloes-5Ghz: entered allmulticast mode
[   45.705389] ath10k_pci 0000:01:00.0 Traadloes-5Ghz: entered promiscuous mode
[   45.712533] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[   45.719529] br-lan: port 6(Traadloes-5Ghz) entered forwarding state
[   45.725709] br-lan: port 6(Traadloes-5Ghz) entered disabled state
[   46.393213] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[   46.393256] br-lan: port 6(Traadloes-5Ghz) entered forwarding state
[   65.888796] ath10k_pci 0000:01:00.0: Invalid VHT mcs 15 peer stats
[   72.268018] ath10k_pci 0000:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  398.867976] ath10k_pci 0000:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0

These lines appear quite frequently in my log:


ath10k_pci 0000:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
ath10k_pci 0000:01:00.0: htt tx: fixing invalid VHT TX rate code 0xff

What do they mean?

brada4 · December 25, 2024, 11:24pm

Please connect to your OpenWrt device using ssh and copy the output of the following commands and post it here using the "Preformatted text </> " button:

Remember to redact passwords, MAC addresses and any public IP addresses you may have:

ubus call system board
cat /etc/config/network
cat /etc/config/wireless
cat /etc/config/dhcp
cat /etc/config/firewall
dmesg

Scope · December 25, 2024, 11:31pm

ubus call system board

root@R7800:~# ubus call system board
{
        "kernel": "6.6.67",
        "hostname": "R7800",
        "system": "ARMv7 Processor rev 0 (v7l)",
        "model": "Netgear Nighthawk X4S R7800",
        "board_name": "netgear,r7800",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10.0-rc4",
                "revision": "r28211-d55754ce0d",
                "target": "ipq806x/generic",
                "description": "OpenWrt 24.10.0-rc4 r28211-d55754ce0d",
                "builddate": "1734915335"
        }
}

/etc/config/network

root@R7800:~# cat /etc/config/network

config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fdd1:5cab:1fcc::/48'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'lan1'
        list ports 'lan2'
        list ports 'lan3'
        list ports 'lan4'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option ipaddr '192.168.0.2'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option gateway '192.168.0.1'
        list dns '192.168.0.1'

/etc/config/wireless

root@R7800:~# cat /etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option path 'soc/1b700000.pci/pci0001:00/0001:00:00.0/0001:01:00.0'
        option band '2g'
        option channel '6'
        option htmode 'HT20'
        option cell_density '0'
        option country 'GB'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'Traadloes'
        option encryption 'psk2'
        option ifname 'Traadloes'
        option key 'xxxxx'

config wifi-device 'radio1'
        option type 'mac80211'
        option path 'soc/1b500000.pci/pci0000:00/0000:00:00.0/0000:01:00.0'
        option band '5g'
        option channel '36'
        option htmode 'VHT80'
        option country 'GB'
        option cell_density '0'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'Traadloes-5Ghz'
        option encryption 'psk2'
        option multicast_to_unicast_all '1'
        option ifname 'Traadloes-5Ghz'
        option key 'xxxxx'

/etc/config/dhcp

root@R7800:~# cat /etc/config/dhcp

config dnsmasq
        option domainneeded '1'
        option localise_queries '1'
        option rebind_protection '1'
        option rebind_localhost '1'
        option local '/lan/'
        option domain 'lan'
        option expandhosts '1'
        option cachesize '1000'
        option readethers '1'
        option leasefile '/tmp/dhcp.leases'
        option resolvfile '/tmp/resolv.conf.d/resolv.conf.auto'
        option localservice '1'
        option ednspacket_max '1232'

config dhcp 'lan'
        option interface 'lan'
        option start '100'
        option limit '150'
        option leasetime '12h'
        option dhcpv4 'server'
        option ignore '1'

config odhcpd 'odhcpd'
        option maindhcp '0'
        option leasefile '/tmp/hosts/odhcpd'
        option leasetrigger '/usr/sbin/odhcpd-update'
        option loglevel '4'

/etc/config/firewall

root@R7800:~# cat /etc/config/firewall

config defaults
        option syn_flood '1'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'
        list network 'lan'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

Scope · December 25, 2024, 11:33pm

dmesg - part 1

root@R7800:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.6.67 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 13.3.0 r28211-d55754ce0d) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Dec 23 00:55:35 2024
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OF: reserved mem: 0x40000000..0x40ffffff (16384 KiB) nomap non-reusable nss@40000000
[    0.000000] OF: reserved mem: 0x41000000..0x411fffff (2048 KiB) nomap non-reusable smem@41000000
[    0.000000] OF: reserved mem: 0x41200000..0x414fffff (3072 KiB) nomap non-reusable rsvd@41200000
[    0.000000] OF: reserved mem: 0x42100000..0x4213ffff (256 KiB) map non-reusable ramoops@42100000
[    0.000000] OF: reserved mem: 0x5fe00000..0x5fffffff (2048 KiB) map reusable rsvd@5fe00000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] percpu: Embedded 13 pages/cpu s21716 r8192 d23340 u53248
[    0.000000] pcpu-alloc: s21716 r8192 d23340 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Kernel command line:
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121800
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 473084K/491520K available (7725K kernel code, 648K rwdata, 1208K rodata, 1024K init, 250K bss, 18436K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000016] Switching to timer-based delay loop, resolution 160ns
[    0.000319] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000346] CPU: Testing write buffer coherency: ok
[    0.000400] pid_max: default: 32768 minimum: 301
[    0.008428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.008453] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.016090] qcom_scm: convention: smc legacy
[    0.017625] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[    0.017862] Setting up static identity map for 0x42300000 - 0x42300060
[    0.018088] rcu: Hierarchical SRCU implementation.
[    0.018097] rcu:     Max phase no-delay instances is 1000.
[    0.018749] smp: Bringing up secondary CPUs ...
[    0.020993] smp: Brought up 1 node, 2 CPUs
[    0.021010] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.021022] CPU: All CPU(s) started in SVC mode.
[    0.037814] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.038018] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.038051] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.042407] pinctrl core: initialized pinctrl subsystem
[    0.045227] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.046012] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.047786] thermal_sys: Registered thermal governor 'step_wise'
[    0.047904] cpuidle: using governor ladder
[    0.047968] cpuidle: using governor menu
[    0.084023] usbcore: registered new interface driver usbfs
[    0.084092] usbcore: registered new interface driver hub
[    0.084160] usbcore: registered new device driver usb
[    0.084252] pps_core: LinuxPPS API ver. 1 registered
[    0.084264] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.084320] PTP clock support registered
[    0.087656] clocksource: Switched to clocksource dg_timer
[    0.097516] NET: Registered PF_INET protocol family
[    0.097759] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.099381] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.099483] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.099512] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.099551] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.099635] TCP: Hash tables configured (established 4096 bind 4096)
[    0.100198] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.100536] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.100568] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.101224] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.101287] PCI: CLS 0 bytes, default 64
[    0.103164] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.103900] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.103916] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.203969] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.208680] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[    0.209240] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[    0.209480] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[    0.209941] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[    0.210009] qcom-pcie 1b500000.pci: Parsing ranges property...
[    0.210090] qcom-pcie 1b500000.pci:       IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[    0.210159] qcom-pcie 1b500000.pci:      MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[    0.211041] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[    0.211184] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[    0.211333] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[    0.211344] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[    0.211351] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[    0.211555] krait-cc soc:clock-controller: L2 @ 384000 KHz
[    0.211808] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[    0.212218] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[    0.212653] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[    0.212715] qcom-pcie 1b700000.pci: Parsing ranges property...
[    0.212789] qcom-pcie 1b700000.pci:       IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[    0.212845] qcom-pcie 1b700000.pci:      MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[    0.217261] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.219847] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.224793] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.224840] msm_serial 16340000.serial: uartclk = 7372800
[    0.225255] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 29, base_baud = 460800) is a MSM
[    0.225297] msm_serial: console setup on port #0
[    0.225384] printk: console [ttyMSM0] enabled
[    0.330410] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[    0.332068] msm_serial: driver initialized
[    0.336072] qcom-pcie 1b700000.pci: iATU: unroll F, 8 ob, 8 ib, align 4K, limit 4G
[    0.347063] loop: module loaded
[    0.353220] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[    0.360932] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[    0.362415] qcom-pcie 1b500000.pci: iATU: unroll F, 8 ob, 8 ib, align 4K, limit 4G
[    0.368785] nand: AMD/Spansion S34MS01G2
[    0.448086] qcom-pcie 1b700000.pci: PCIe Gen.1 x1 link up
[    0.456914] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.465251] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.470962] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[    0.481076] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.485687] Creating 8 MTD partitions on "qcom_nand.0":
[    0.490636] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    0.497575] 0x000000000000-0x000000c80000 : "qcadata"
[    0.505649] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.531202] 0x000000c80000-0x000001180000 : "APPSBL"
[    0.535279] pci_bus 0001:00: scanning bus
[    0.548639] 0x000001180000-0x000001200000 : "APPSBLENV"
[    0.550281] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.556415] 0x000001200000-0x000001340000 : "art"
[    0.562859] pci 0001:00:00.0: supports D1
[    0.575828] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[    0.579188] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.584490] 0x000001340000-0x000001480000 : "artbak"
[    0.590104] pci 0001:00:00.0: PME# disabled
[    0.599713] 0x000001480000-0x000001880000 : "kernel"
[    0.609973] pci_bus 0001:00: fixups for bus
[    0.618360] 0x000001880000-0x000007900000 : "ubi"
[    0.621993] PCI: bus0: Fast back to back transfers disabled
[    0.787228] qcom-pcie 1b500000.pci: PCIe Gen.2 x1 link up
[    0.788987] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.796850] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.805014] pci_bus 0001:01: scanning bus
[    0.810700] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.818357] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[    0.823876] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.831642] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.838716] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.845427] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.851995] pci_bus 0000:00: scanning bus
[    0.859783] pci 0001:01:00.0: PME# disabled
[    0.866623] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.874889] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.882573] pci 0000:00:00.0: supports D1
[    0.889351] pci_bus 0001:01: fixups for bus
[    0.894705] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.901196] PCI: bus1: Fast back to back transfers disabled
[    0.906345] pci 0000:00:00.0: PME# disabled
[    0.914931] pci_bus 0001:01: bus scan returning with max=01
[    0.923895] pci_bus 0000:00: fixups for bus
[    0.923968] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.928074] PCI: bus0: Fast back to back transfers disabled
[    0.935515] pci_bus 0001:00: bus scan returning with max=ff
[    0.938625] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.945171] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.952767] pci_bus 0000:01: scanning bus
[    0.956612] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.962236] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[    0.969585] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.975773] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.982494] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.989056] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.993368] pcieport 0001:00:00.0: assign IRQ: got 32
[    1.002057] pci 0000:01:00.0: PME# disabled
[    1.007302] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43a1e000
[    1.014999] pci_bus 0000:01: fixups for bus
[    1.020246] 0x000007900000-0x000008000000 : "reserve"
[    1.023957] PCI: bus1: Fast back to back transfers disabled
[    1.212676] pci_bus 0000:01: bus scan returning with max=01
[    1.212705] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    1.212731] pci_bus 0000:00: bus scan returning with max=ff
[    1.212839] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    1.218139] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    1.225146] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.232141] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    1.237755] pcieport 0000:00:00.0: assign IRQ: got 34
[    1.238111] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43a20000
[    1.247260] pcieport 0000:00:00.0: AER: enabled with IRQ 35
[    1.247499] pcieport 0000:00:00.0: save config 0x00: 0x010117cb
[    1.247521] pcieport 0000:00:00.0: save config 0x04: 0x00100547
[    1.247539] pcieport 0000:00:00.0: save config 0x08: 0xff000000
[    1.247542] pcieport 0001:00:00.0: AER: enabled with IRQ 33
[    1.247556] pcieport 0000:00:00.0: save config 0x0c: 0x00010010
[    1.247571] pcieport 0000:00:00.0: save config 0x10: 0x00000000
[    1.251768] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[    1.251788] pcieport 0000:00:00.0: save config 0x18: 0x00ff0100

Scope · December 25, 2024, 11:34pm

dmesg part 2

[ 1.251804] pcieport 0000:00:00.0: save config 0x1c: 0x000000f0
[ 1.251821] pcieport 0000:00:00.0: save config 0x20: 0x08100800
[ 1.251837] pcieport 0000:00:00.0: save config 0x24: 0x0001fff1
[ 1.251856] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[ 1.251875] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[ 1.251892] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[ 1.251908] pcieport 0000:00:00.0: save config 0x34: 0x00000040
[ 1.251925] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[ 1.251941] pcieport 0000:00:00.0: save config 0x3c: 0x00030122
[ 1.251959] pcieport 0001:00:00.0: save config 0x00: 0x010117cb
[ 1.251994] pcieport 0001:00:00.0: save config 0x04: 0x00100547
[ 1.252023] pcieport 0001:00:00.0: save config 0x08: 0xff000000
[ 1.252051] pcieport 0001:00:00.0: save config 0x0c: 0x00010010
[ 1.252077] pcieport 0001:00:00.0: save config 0x10: 0x00000000
[ 1.252104] pcieport 0001:00:00.0: save config 0x14: 0x00000000
[ 1.252131] pcieport 0001:00:00.0: save config 0x18: 0x00ff0100
[ 1.252157] pcieport 0001:00:00.0: save config 0x1c: 0x000000f0
[ 1.252183] pcieport 0001:00:00.0: save config 0x20: 0x2e102e00
[ 1.252209] pcieport 0001:00:00.0: save config 0x24: 0x0001fff1
[ 1.252235] pcieport 0001:00:00.0: save config 0x28: 0x00000000
[ 1.252261] pcieport 0001:00:00.0: save config 0x2c: 0x00000000
[ 1.252287] pcieport 0001:00:00.0: save config 0x30: 0x00000000
[ 1.252314] pcieport 0001:00:00.0: save config 0x34: 0x00000040
[ 1.252340] pcieport 0001:00:00.0: save config 0x38: 0x00000000
[ 1.252366] pcieport 0001:00:00.0: save config 0x3c: 0x00030120
[ 1.271832] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 1.271911] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 1.279264] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 1.285356] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 1.291161] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 1.298477] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 1.304201] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 1.312009] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 1.319899] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 1.325639] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 1.333084] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 1.339861] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 1.347342] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 1.354450] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.364027] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 1.369316] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 1.376713] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 1.383408] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 1.389311] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 1.396648] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 1.402580] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 1.410276] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 1.418180] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 1.423903] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 1.431378] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 1.438142] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 1.445604] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 1.452700] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.462220] i2c_dev: i2c /dev entries driver
[ 1.473608] sdhci: Secure Digital Host Controller Interface driver
[ 1.473660] sdhci: Copyright(c) Pierre Ossman
[ 1.478815] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.488724] NET: Registered PF_INET6 protocol family
[ 1.492207] Segment Routing with IPv6
[ 1.493871] In-situ OAM (IOAM) with IPv6
[ 1.497549] NET: Registered PF_PACKET protocol family
[ 1.501602] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.506924] 8021q: 802.1Q VLAN Support v1.8
[ 1.519748] Registering SWP/SWPB emulation handler
[ 1.591626] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 1.606974] s1a: Bringing 0uV into 1050000-1050000uV
[ 1.607530] s1b: Bringing 0uV into 1050000-1050000uV
[ 1.611626] s2a: Bringing 0uV into 775000-775000uV
[ 1.616417] s2b: Bringing 0uV into 775000-775000uV
[ 1.833421] qca8k 37000000.mdio-mii:10: configuring for fixed/rgmii link mode
[ 1.844268] qca8k 37000000.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 1.850601] qca8k 37000000.mdio-mii:10: configuring for fixed/sgmii link mode
[ 1.864128] qca8k 37000000.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 1.966323] qca8k 37000000.mdio-mii:10 lan4 (uninitialized): PHY [qca8k-0.0:00] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.096529] qca8k 37000000.mdio-mii:10 lan3 (uninitialized): PHY [qca8k-0.0:01] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.206496] qca8k 37000000.mdio-mii:10 lan2 (uninitialized): PHY [qca8k-0.0:02] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.316428] qca8k 37000000.mdio-mii:10 lan1 (uninitialized): PHY [qca8k-0.0:03] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.426456] qca8k 37000000.mdio-mii:10 wan (uninitialized): PHY [qca8k-0.0:04] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.427531] ipq806x-gmac-dwmac 37200000.ethernet eth0: entered promiscuous mode
[ 2.437881] ipq806x-gmac-dwmac 37400000.ethernet eth1: entered promiscuous mode
[ 2.444615] DSA: tree 0 setup
[ 2.457913] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 2.472734] UBI: auto-attach mtd6
[ 2.472762] ubi0: attaching mtd6
[ 2.598060] random: crng init done
[ 3.166959] ubi0: scanning is finished
[ 3.176216] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 3.176240] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.180642] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.187358] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.194288] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 3.201037] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.207238] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1727094886
[ 3.214342] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 3.223792] ubi0: background thread "ubi_bgt0d" started, PID 69
[ 3.233342] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.238460] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.244111] clk: Disabling unused clocks
[ 3.254540] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.255077] Freeing unused kernel image (initmem) memory: 1024K
[ 3.260833] Run /sbin/init as init process
[ 3.266373] with arguments:
[ 3.266377] /sbin/init
[ 3.266381] with environment:
[ 3.266386] HOME=/
[ 3.266389] TERM=linux
[ 3.499915] init: Console is alive
[ 3.500059] init: - watchdog -
[ 3.502284] init: Watchdog has previously reset the system
[ 4.025690] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.037865] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 4.041734] pstore: Using crash dump compression: deflate
[ 4.043640] printk: console [ramoops-1] enabled
[ 4.050200] pstore: Registered ramoops as persistent store backend
[ 4.053439] ramoops: using 0x40000@0x42100000, ecc: 0
[ 4.064509] SCSI subsystem initialized
[ 4.068024] libata version 3.00 loaded.
[ 4.069805] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 4.069942] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 4.076025] ahci 29000000.sata: supply target not found, using dummy regulator
[ 4.083674] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 4.089984] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 4.095369] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 4.104591] scsi host0: ahci
[ 4.112476] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 46
[ 4.441675] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.562568] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.562618] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.567136] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002000010
[ 4.574610] xhci-hcd xhci-hcd.0.auto: irq 47, io mem 0x10000000
[ 4.584098] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.589858] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.595342] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 4.603359] hub 1-0:1.0: USB hub found
[ 4.609560] hub 1-0:1.0: 1 port detected
[ 4.613498] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.617629] hub 2-0:1.0: USB hub found
[ 4.626177] hub 2-0:1.0: 1 port detected
[ 4.629273] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.633018] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.638493] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002000010
[ 4.645887] xhci-hcd xhci-hcd.1.auto: irq 48, io mem 0x11000000
[ 4.655445] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.661208] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 4.666695] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.674686] hub 3-0:1.0: USB hub found
[ 4.680942] hub 3-0:1.0: 1 port detected
[ 4.684833] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.689467] hub 4-0:1.0: USB hub found
[ 4.696748] hub 4-0:1.0: 1 port detected
[ 4.702546] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.710946] init: - preinit -
[ 5.633989] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 5.634689] dwmac1000: Master AXI performs any burst length
[ 5.641238] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 5.656467] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 5.656595] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 5.664848] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 5.671490] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 5.685869] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal link mode
[ 9.924284] qca8k 37000000.mdio-mii:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.987715] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 9.998034] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 193
[ 10.034874] UBIFS (ubi0:1): recovery needed
[ 10.145218] UBIFS (ubi0:1): recovery completed
[ 10.145375] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.148644] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.156461] UBIFS (ubi0:1): FS size: 88502272 bytes (84 MiB, 697 LEBs), max 708 LEBs, journal size 4444160 bytes (4 MiB, 35 LEBs)
[ 10.166431] UBIFS (ubi0:1): reserved for root: 4180180 bytes (4082 KiB)
[ 10.178062] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 5BCC50B6-0109-44E8-8B3C-6FF29BEA213D, small LPT model
[ 10.189801] mount_root: switching to ubifs overlay
[ 10.208943] urandom-seed: Seeding with /etc/urandom.seed
[ 10.291669] qca8k 37000000.mdio-mii:10 lan1: Link is Down
[ 10.300700] procd: - early -
[ 10.300808] procd: - watchdog -
[ 10.302815] procd: Watchdog has previously reset the system
[ 10.871200] procd: - watchdog -
[ 10.871281] procd: Watchdog has previously reset the system
[ 10.874578] procd: - ubus -
[ 11.035225] procd: - init -
[ 11.423323] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.445238] Loading modules backported from Linux version v6.11.2-0-g7aa21fec187b
[ 11.445276] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
[ 11.593291] PPP generic driver version 2.4.2
[ 11.593867] NET: Registered PF_PPPOX protocol family
[ 11.608477] ath10k_pci 0001:01:00.0: assign IRQ: got 32
[ 11.608510] ath10k 6.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 11.609042] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 11.615387] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 11.615861] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43a1e000
[ 11.616032] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.681428] urngd: v1.0.2 started.
[ 12.325543] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 12.325593] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 12.336070] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 14.671501] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 0bfe5c35
[ 18.231275] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 18.231318] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 18.315366] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 18.316234] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 18.649189] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[ 18.731457] ath: EEPROM regdomain: 0x0
[ 18.731469] ath: EEPROM indicates default country code should be used
[ 18.731474] ath: doing EEPROM country->regdmn map search
[ 18.731482] ath: country maps to regdmn code: 0x3a
[ 18.731490] ath: Country alpha2 being used: US
[ 18.731495] ath: Regpair used: 0x3a
[ 18.778293] ath10k_pci 0000:01:00.0: assign IRQ: got 34
[ 18.778324] ath10k 6.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 18.778794] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 18.785209] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 18.785658] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43a20000
[ 18.785818] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 19.231271] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 19.231324] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 19.242010] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 21.573514] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 0bfe5c35
[ 25.125383] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 25.125429] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 25.207503] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 25.208338] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 25.495466] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[ 25.581529] ath: EEPROM regdomain: 0x0
[ 25.581542] ath: EEPROM indicates default country code should be used
[ 25.581547] ath: doing EEPROM country->regdmn map search
[ 25.581555] ath: country maps to regdmn code: 0x3a
[ 25.581560] ath: Country alpha2 being used: US
[ 25.581565] ath: Regpair used: 0x3a
[ 25.630749] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 29.098174] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[ 29.102117] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 29.103885] dwmac1000: Master AXI performs any burst length
[ 29.111684] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 29.126922] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 29.127091] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 29.134898] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 29.142138] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 29.178292] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 29.178996] dwmac1000: Master AXI performs any burst length
[ 29.185521] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 29.200910] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 29.201084] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 29.212432] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 29.215976] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 29.227142] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal link mode
[ 29.306952] br-lan: port 1(lan1) entered blocking state
[ 29.306994] br-lan: port 1(lan1) entered disabled state
[ 29.311121] qca8k 37000000.mdio-mii:10 lan1: entered allmulticast mode
[ 29.316268] ipq806x-gmac-dwmac 37400000.ethernet eth1: entered allmulticast mode
[ 29.330242] qca8k 37000000.mdio-mii:10 lan1: entered promiscuous mode
[ 29.387171] qca8k 37000000.mdio-mii:10 lan2: configuring for phy/internal link mode
[ 29.416300] br-lan: port 2(lan2) entered blocking state
[ 29.416344] br-lan: port 2(lan2) entered disabled state
[ 29.420503] qca8k 37000000.mdio-mii:10 lan2: entered allmulticast mode
[ 29.430866] qca8k 37000000.mdio-mii:10 lan2: entered promiscuous mode
[ 29.464317] qca8k 37000000.mdio-mii:10 lan3: configuring for phy/internal link mode
[ 29.474990] br-lan: port 3(lan3) entered blocking state
[ 29.475030] br-lan: port 3(lan3) entered disabled state
[ 29.479145] qca8k 37000000.mdio-mii:10 lan3: entered allmulticast mode
[ 29.495184] qca8k 37000000.mdio-mii:10 lan3: entered promiscuous mode
[ 29.536029] qca8k 37000000.mdio-mii:10 lan4: configuring for phy/internal link mode
[ 29.536401] br-lan: port 4(lan4) entered blocking state
[ 29.542645] br-lan: port 4(lan4) entered disabled state
[ 29.547742] qca8k 37000000.mdio-mii:10 lan4: entered allmulticast mode
[ 29.571865] qca8k 37000000.mdio-mii:10 lan4: entered promiscuous mode
[ 30.131133] ath: EEPROM regdomain: 0x833a
[ 30.131171] ath: EEPROM indicates we should expect a country code
[ 30.134133] ath: doing EEPROM country->regdmn map search
[ 30.140294] ath: country maps to regdmn code: 0x37
[ 30.145585] ath: Country alpha2 being used: GB
[ 30.150267] ath: Regpair used: 0x37
[ 30.154618] ath: regdomain 0x833a dynamically updated by user
[ 30.158091] ath: EEPROM regdomain: 0x833a
[ 30.163973] ath: EEPROM indicates we should expect a country code
[ 30.167991] ath: doing EEPROM country->regdmn map search
[ 30.174041] ath: country maps to regdmn code: 0x37
[ 30.179410] ath: Country alpha2 being used: GB
[ 30.183953] ath: Regpair used: 0x37
[ 30.188441] ath: regdomain 0x833a dynamically updated by user
[ 32.724122] qca8k 37000000.mdio-mii:10 lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[ 33.444164] qca8k 37000000.mdio-mii:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 34.647488] qca8k 37000000.mdio-mii:10 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 37.508355] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 37.508432] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 37.592243] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 37.593104] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 38.104556] ath10k_pci 0001:01:00.0: rts threshold -1
[ 38.104865] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 38.108683] ------------[ cut here ]------------
[ 38.119582] WARNING: CPU: 1 PID: 1118 at backports-6.11.2/net/mac80211/main.c:272 0xbf208888 [mac80211@ee4ab5fc+0x77000]
[ 38.124305] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath10k_pci(O) ath10k_core(O) ath(O) pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211(O) cfg80211(O) slhc nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c crc_ccitt compat(O) ledtrig_usbport sha512_arm seqiv geniv cmac leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_ipq806x_usb ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod scsi_common ehci_hcd ramoops reed_solomon pstore gpio_button_hotplug(O) crc32c_generic
[ 38.188068] CPU: 1 PID: 1118 Comm: hostapd Tainted: G O 6.6.67 #0
[ 38.210237] Hardware name: Generic DT based system
[ 38.217704] Function entered at [] from []
[ 38.222388] Function entered at [] from []
[ 38.228205] Function entered at [] from []
[ 38.234020] Function entered at [] from []
[ 38.239836] Function entered at [] from []
[ 38.245664] Function entered at [] from []
[ 38.251468] Function entered at [] from []
[ 38.257285] Function entered at [] from []
[ 38.263100] Function entered at [] from []
[ 38.268914] Function entered at [] from []
[ 38.274731] Function entered at [] from []
[ 38.280548] Function entered at [] from []
[ 38.286365] Function entered at [] from []
[ 38.292180] Function entered at [] from []
[ 38.297994] Exception stack(0xc349ffa8 to 0xc349fff0)
[ 38.303812] ffa0: 00000010 beef3848 00000010 00008914 beef3848 beef3838
[ 38.308937] ffc0: 00000010 beef3848 00000010 00000036 00000001 00000001 00000000 00000020
[ 38.317095] ffe0: b6fd2f74 beef3708 00487f44 b6f8b704
[ 38.325326] ---[ end trace 0000000000000000 ]---
[ 38.330569] br-lan: port 4(lan4) entered blocking state
[ 38.334980] br-lan: port 4(lan4) entered forwarding state
[ 38.340083] br-lan: port 1(lan1) entered blocking state
[ 38.345545] br-lan: port 1(lan1) entered forwarding state
[ 38.350656] br-lan: port 3(lan3) entered blocking state
[ 38.356070] br-lan: port 3(lan3) entered forwarding state
[ 38.361960] br-lan: port 5(Traadloes) entered blocking state
[ 38.366664] br-lan: port 5(Traadloes) entered disabled state
[ 38.372515] ath10k_pci 0001:01:00.0 Traadloes: entered allmulticast mode
[ 38.378265] ath10k_pci 0001:01:00.0 Traadloes: entered promiscuous mode
[ 38.415392] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 38.730910] br-lan: port 5(Traadloes) entered blocking state
[ 38.730946] br-lan: port 5(Traadloes) entered forwarding state
[ 44.995804] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 44.995878] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 45.077935] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 45.078757] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 45.462745] ath10k_pci 0000:01:00.0: rts threshold -1
[ 45.463057] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 45.466828] ------------[ cut here ]------------
[ 45.477886] WARNING: CPU: 0 PID: 1118 at backports-6.11.2/net/mac80211/main.c:272 0xbf208888 [mac80211@ee4ab5fc+0x77000]
[ 45.482527] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath10k_pci(O) ath10k_core(O) ath(O) pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211(O) cfg80211(O) slhc nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c crc_ccitt compat(O) ledtrig_usbport sha512_arm seqiv geniv cmac leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom ohci_platform ohci_hcd phy_qcom_ipq806x_usb ahci fsl_mph_dr_of ehci_platform ehci_fsl sd_mod ahci_platform libahci_platform libahci libata scsi_mod scsi_common ehci_hcd ramoops reed_solomon pstore gpio_button_hotplug(O) crc32c_generic
[ 45.546334] CPU: 0 PID: 1118 Comm: hostapd Tainted: G W O 6.6.67 #0
[ 45.568425] Hardware name: Generic DT based system
[ 45.575892] Function entered at [] from []
[ 45.580577] Function entered at [] from []
[ 45.586394] Function entered at [] from []
[ 45.592210] Function entered at [] from []
[ 45.598025] Function entered at [] from []
[ 45.603843] Function entered at [] from []
[ 45.609656] Function entered at [] from []
[ 45.615474] Function entered at [] from []
[ 45.621289] Function entered at [] from []
[ 45.627103] Function entered at [] from []
[ 45.632921] Function entered at [] from []
[ 45.638736] Function entered at [] from []
[ 45.644552] Function entered at [] from []
[ 45.650369] Function entered at [] from []
[ 45.656183] Exception stack(0xc349ffa8 to 0xc349fff0)
[ 45.662001] ffa0: 00000010 beef3848 00000010 00008914 beef3848 beef3838
[ 45.667127] ffc0: 00000010 beef3848 00000010 00000036 00000001 00000001 00000000 00000020
[ 45.675286] ffe0: b6fd2f74 beef3708 00487f44 b6f8b704
[ 45.683655] ---[ end trace 0000000000000000 ]---
[ 45.690823] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[ 45.693170] br-lan: port 6(Traadloes-5Ghz) entered disabled state
[ 45.699264] ath10k_pci 0000:01:00.0 Traadloes-5Ghz: entered allmulticast mode
[ 45.705389] ath10k_pci 0000:01:00.0 Traadloes-5Ghz: entered promiscuous mode
[ 45.712533] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[ 45.719529] br-lan: port 6(Traadloes-5Ghz) entered forwarding state
[ 45.725709] br-lan: port 6(Traadloes-5Ghz) entered disabled state
[ 46.393213] br-lan: port 6(Traadloes-5Ghz) entered blocking state
[ 46.393256] br-lan: port 6(Traadloes-5Ghz) entered forwarding state
[ 65.888796] ath10k_pci 0000:01:00.0: Invalid VHT mcs 15 peer stats
[ 72.268018] ath10k_pci 0000:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0 arvif->paused: 0x0
[ 398.867976] ath10k_pci 0000:01:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0 arvif->paused: 0x0
[ 605.214603] ath10k_pci 0000:01:00.0: htt tx: fixing invalid VHT TX rate code 0xff

brada4 · December 25, 2024, 11:39pm

Please change kmod-ath10k-ct and ath10k-firmware...ct to ther mainline siblings without -ct suffix.

Scope · December 26, 2024, 12:17am

I've done another build with the 2 changes.. I think the router is running the correct driver for the ath10 now:

dmesg

root@R7800:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.6.67 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 13.3.0 r28211-d55754ce0d) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Dec 23 00:55:35 2024
[    0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OF: reserved mem: 0x40000000..0x40ffffff (16384 KiB) nomap non-reusable nss@40000000
[    0.000000] OF: reserved mem: 0x41000000..0x411fffff (2048 KiB) nomap non-reusable smem@41000000
[    0.000000] OF: reserved mem: 0x41200000..0x414fffff (3072 KiB) nomap non-reusable rsvd@41200000
[    0.000000] OF: reserved mem: 0x42100000..0x4213ffff (256 KiB) map non-reusable ramoops@42100000
[    0.000000] OF: reserved mem: 0x5fe00000..0x5fffffff (2048 KiB) map reusable rsvd@5fe00000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[    0.000000] percpu: Embedded 13 pages/cpu s21716 r8192 d23340 u53248
[    0.000000] pcpu-alloc: s21716 r8192 d23340 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Kernel command line:
[    0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121800
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 473084K/491520K available (7725K kernel code, 648K rwdata, 1208K rodata, 1024K init, 250K bss, 18436K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[    0.000001] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[    0.000016] Switching to timer-based delay loop, resolution 160ns
[    0.000319] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[    0.000346] CPU: Testing write buffer coherency: ok
[    0.000401] pid_max: default: 32768 minimum: 301
[    0.008428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.008452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.016055] qcom_scm: convention: smc legacy
[    0.017588] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[    0.017820] Setting up static identity map for 0x42300000 - 0x42300060
[    0.018049] rcu: Hierarchical SRCU implementation.
[    0.018058] rcu:     Max phase no-delay instances is 1000.
[    0.018716] smp: Bringing up secondary CPUs ...
[    0.020937] smp: Brought up 1 node, 2 CPUs
[    0.020954] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[    0.020966] CPU: All CPU(s) started in SVC mode.
[    0.037822] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[    0.038026] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.038060] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.042437] pinctrl core: initialized pinctrl subsystem
[    0.045263] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.046054] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.047800] thermal_sys: Registered thermal governor 'step_wise'
[    0.047920] cpuidle: using governor ladder
[    0.047984] cpuidle: using governor menu
[    0.084017] usbcore: registered new interface driver usbfs
[    0.084088] usbcore: registered new interface driver hub
[    0.084154] usbcore: registered new device driver usb
[    0.084249] pps_core: LinuxPPS API ver. 1 registered
[    0.084260] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.084315] PTP clock support registered
[    0.087654] clocksource: Switched to clocksource dg_timer
[    0.097493] NET: Registered PF_INET protocol family
[    0.097731] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.099379] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.099478] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.099506] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.099545] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.099627] TCP: Hash tables configured (established 4096 bind 4096)
[    0.100191] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.100528] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.100559] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.101210] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.101273] PCI: CLS 0 bytes, default 64
[    0.103137] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.103878] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.103895] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.203938] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.208618] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[    0.209274] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[    0.209513] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[    0.209962] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[    0.210031] qcom-pcie 1b500000.pci: Parsing ranges property...
[    0.210103] qcom-pcie 1b500000.pci:       IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[    0.210168] qcom-pcie 1b500000.pci:      MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[    0.211066] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[    0.211088] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[    0.211344] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[    0.211363] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[    0.211372] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[    0.211557] krait-cc soc:clock-controller: L2 @ 384000 KHz
[    0.212215] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[    0.212370] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[    0.212783] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[    0.212845] qcom-pcie 1b700000.pci: Parsing ranges property...
[    0.212905] qcom-pcie 1b700000.pci:       IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[    0.212963] qcom-pcie 1b700000.pci:      MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[    0.217058] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[    0.219640] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.224557] msm_serial 16340000.serial: msm_serial: detected port #0
[    0.224603] msm_serial 16340000.serial: uartclk = 7372800
[    0.225021] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 29, base_baud = 460800) is a MSM
[    0.225065] msm_serial: console setup on port #0
[    0.225148] printk: console [ttyMSM0] enabled
[    0.330360] qcom-pcie 1b700000.pci: Using 32 MSI vectors
[    0.331831] msm_serial: driver initialized
[    0.335830] qcom-pcie 1b700000.pci: iATU: unroll F, 8 ob, 8 ib, align 4K, limit 4G
[    0.346736] loop: module loaded
[    0.353004] qcom-pcie 1b500000.pci: Using 32 MSI vectors
[    0.360697] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[    0.362178] qcom-pcie 1b500000.pci: iATU: unroll F, 8 ob, 8 ib, align 4K, limit 4G
[    0.368534] nand: AMD/Spansion S34MS01G2
[    0.448057] qcom-pcie 1b700000.pci: PCIe Gen.1 x1 link up
[    0.456696] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.465001] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[    0.470708] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[    0.480825] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.485450] Creating 8 MTD partitions on "qcom_nand.0":
[    0.490386] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    0.497340] 0x000000000000-0x000000c80000 : "qcadata"
[    0.505431] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[    0.531095] 0x000000c80000-0x000001180000 : "APPSBL"
[    0.535043] pci_bus 0001:00: scanning bus
[    0.548493] 0x000001180000-0x000001200000 : "APPSBLENV"
[    0.550036] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.556171] 0x000001200000-0x000001340000 : "art"
[    0.562647] pci 0001:00:00.0: supports D1
[    0.575642] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[    0.578940] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[    0.584253] 0x000001340000-0x000001480000 : "artbak"
[    0.589857] pci 0001:00:00.0: PME# disabled
[    0.596508] pci_bus 0001:00: fixups for bus
[    0.599541] 0x000001480000-0x000001880000 : "kernel"
[    0.602980] PCI: bus0: Fast back to back transfers disabled
[    0.613938] 0x000001880000-0x000007900000 : "ubi"
[    0.616177] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.782222] qcom-pcie 1b500000.pci: PCIe Gen.2 x1 link up
[    0.788993] pci_bus 0001:01: scanning bus
[    0.796619] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[    0.804852] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[    0.810450] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.818108] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.823723] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.832512] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[    0.838560] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[    0.843822] pci 0001:01:00.0: PME# disabled
[    0.851775] pci_bus 0000:00: scanning bus
[    0.859905] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.866385] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[    0.875237] pci_bus 0001:01: fixups for bus
[    0.882352] pci 0000:00:00.0: supports D1
[    0.888202] PCI: bus1: Fast back to back transfers disabled
[    0.894470] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.900873] pci_bus 0001:01: bus scan returning with max=01
[    0.906110] pci 0000:00:00.0: PME# disabled
[    0.914690] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    0.923675] pci_bus 0000:00: fixups for bus
[    0.923733] pci_bus 0001:00: bus scan returning with max=ff
[    0.927723] PCI: bus0: Fast back to back transfers disabled
[    0.935354] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[    0.938404] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[    0.944924] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[    0.952513] pci_bus 0000:01: scanning bus
[    0.956504] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[    0.961984] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[    0.969203] pci 0001:00:00.0:   bridge window [mem 0x2e000000-0x2e1fffff]
[    0.975537] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.982606] pcieport 0001:00:00.0: assign IRQ: got 32
[    0.988825] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.993014] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x43a1e000
[    1.001816] pci 0000:01:00.0: PME# disabled
[    1.007784] pcieport 0001:00:00.0: AER: enabled with IRQ 33
[    1.014803] pci_bus 0000:01: fixups for bus
[    1.018913] pcieport 0001:00:00.0: save config 0x00: 0x010117cb
[    1.023701] PCI: bus1: Fast back to back transfers disabled
[    1.029959] pcieport 0001:00:00.0: save config 0x04: 0x00100547
[    1.034483] pci_bus 0000:01: bus scan returning with max=01
[    1.038549] pcieport 0001:00:00.0: save config 0x08: 0xff000000
[    1.045953] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[    1.051826] pcieport 0001:00:00.0: save config 0x0c: 0x00010010
[    1.056801] pci_bus 0000:00: bus scan returning with max=ff
[    1.061822] pcieport 0001:00:00.0: save config 0x10: 0x00000000
[    1.067049] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[    1.072034] pcieport 0001:00:00.0: save config 0x14: 0x00000000
[    1.077288] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[    1.083440] pcieport 0001:00:00.0: save config 0x18: 0x00ff0100
[    1.089716] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.094822] pcieport 0001:00:00.0: save config 0x1c: 0x000000f0
[    1.101757] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x081fffff]
[    1.101988] pcieport 0000:00:00.0: assign IRQ: got 34
[    1.107754] pcieport 0001:00:00.0: save config 0x20: 0x2e102e00
[    1.114150] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x43a20000
[    1.120773] pcieport 0001:00:00.0: save config 0x24: 0x0001fff1
[    1.148295] pcieport 0000:00:00.0: AER: enabled with IRQ 35
[    1.226204] 0x000007900000-0x000008000000 : "reserve"
[    1.232391] pcieport 0000:00:00.0: save config 0x24: 0x0001fff1
[    1.232406] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[    1.249998] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[    1.250034] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[    1.250070] pcieport 0000:00:00.0: save config 0x34: 0x00000040
[    1.250089] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[    1.250105] pcieport 0000:00:00.0: save config 0x3c: 0x00030122
[    1.281899] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[    1.281978] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[    1.289338] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[    1.295523] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    1.301131] ipq806x-gmac-dwmac 37200000.ethernet:    DWMAC1000
[    1.308571] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[    1.314268] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[    1.322107] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[    1.330026] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[    1.335707] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[    1.343195] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[    1.349967] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[    1.357408] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[    1.364510] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.374085] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[    1.379390] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[    1.386787] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[    1.393442] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    1.399388] ipq806x-gmac-dwmac 37400000.ethernet:    DWMAC1000
[    1.406713] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[    1.412620] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[    1.420348] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[    1.428239] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[    1.433970] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[    1.441440] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[    1.448203] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[    1.455670] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[    1.462791] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.472312] i2c_dev: i2c /dev entries driver
[    1.483665] sdhci: Secure Digital Host Controller Interface driver
[    1.483719] sdhci: Copyright(c) Pierre Ossman
[    1.488845] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.498759] NET: Registered PF_INET6 protocol family
[    1.501907] Segment Routing with IPv6
[    1.503931] In-situ OAM (IOAM) with IPv6
[    1.507603] NET: Registered PF_PACKET protocol family
[    1.511695] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.516970] 8021q: 802.1Q VLAN Support v1.8
[    1.529811] Registering SWP/SWPB emulation handler
[    1.601488] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[    1.616849] s1a: Bringing 0uV into 1050000-1050000uV
[    1.617401] s1b: Bringing 0uV into 1050000-1050000uV
[    1.621477] s2a: Bringing 0uV into 775000-775000uV
[    1.626306] s2b: Bringing 0uV into 775000-775000uV
[    1.839420] qca8k 37000000.mdio-mii:10: configuring for fixed/rgmii link mode
[    1.849017] qca8k 37000000.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[    1.854725] qca8k 37000000.mdio-mii:10: configuring for fixed/sgmii link mode
[    1.867379] qca8k 37000000.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[    1.972509] qca8k 37000000.mdio-mii:10 lan4 (uninitialized): PHY [qca8k-0.0:00] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.091601] qca8k 37000000.mdio-mii:10 lan3 (uninitialized): PHY [qca8k-0.0:01] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.206559] qca8k 37000000.mdio-mii:10 lan2 (uninitialized): PHY [qca8k-0.0:02] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.316398] qca8k 37000000.mdio-mii:10 lan1 (uninitialized): PHY [qca8k-0.0:03] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.426426] qca8k 37000000.mdio-mii:10 wan (uninitialized): PHY [qca8k-0.0:04] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.427479] ipq806x-gmac-dwmac 37200000.ethernet eth0: entered promiscuous mode
[    2.437836] ipq806x-gmac-dwmac 37400000.ethernet eth1: entered promiscuous mode
[    2.444596] DSA: tree 0 setup
[    2.457944] thermal thermal_zone0: failed to read out thermal zone (-110)
[    2.472672] UBI: auto-attach mtd6
[    2.472700] ubi0: attaching mtd6
[    2.598037] random: crng init done
[    3.167698] ubi0: scanning is finished
[    3.177013] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[    3.177037] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.181453] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.188231] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.195012] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[    3.201846] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    3.208095] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1727094886
[    3.215068] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[    3.225203] block ubiblock0_0: created from ubi0:0(rootfs)
[    3.233524] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    3.233619] ubi0: background thread "ubi_bgt0d" started, PID 70
[    3.239046] clk: Disabling unused clocks
[    3.255004] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    3.255544] Freeing unused kernel image (initmem) memory: 1024K
[    3.261263] Run /sbin/init as init process
[    3.266837]   with arguments:
[    3.266841]     /sbin/init
[    3.266845]   with environment:
[    3.266850]     HOME=/
[    3.266853]     TERM=linux
[    3.500970] init: Console is alive
[    3.501110] init: - watchdog -
[    3.503338] init: Watchdog has previously reset the system
[    4.004048] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.015997] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    4.020188] pstore: Using crash dump compression: deflate
[    4.021773] printk: console [ramoops-1] enabled
[    4.028311] pstore: Registered ramoops as persistent store backend
[    4.031570] ramoops: using 0x40000@0x42100000, ecc: 0
[    4.042594] SCSI subsystem initialized
[    4.046072] libata version 3.00 loaded.
[    4.047838] ahci 29000000.sata: supply ahci not found, using dummy regulator
[    4.048049] ahci 29000000.sata: supply phy not found, using dummy regulator
[    4.054067] ahci 29000000.sata: supply target not found, using dummy regulator
[    4.061146] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[    4.068012] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    4.073399] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[    4.083377] scsi host0: ahci
[    4.090491] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 46
[    4.419560] ata1: SATA link down (SStatus 0 SControl 300)
[    4.542627] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.542677] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.547147] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002000010
[    4.554684] xhci-hcd xhci-hcd.0.auto: irq 47, io mem 0x10000000
[    4.564155] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.569922] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.575406] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    4.583503] hub 1-0:1.0: USB hub found
[    4.589629] hub 1-0:1.0: 1 port detected
[    4.593559] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.597683] hub 2-0:1.0: USB hub found
[    4.605591] hub 2-0:1.0: 1 port detected
[    4.610407] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.613077] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    4.618558] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002000010
[    4.625940] xhci-hcd xhci-hcd.1.auto: irq 48, io mem 0x11000000
[    4.635507] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.641274] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    4.646753] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    4.654761] hub 3-0:1.0: USB hub found
[    4.660977] hub 3-0:1.0: 1 port detected
[    4.664885] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.669077] hub 4-0:1.0: USB hub found
[    4.676801] hub 4-0:1.0: 1 port detected
[    4.682606] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.690320] init: - preinit -
[    5.614065] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[    5.614767] dwmac1000: Master AXI performs any burst length
[    5.621305] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[    5.636542] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    5.636677] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[    5.644921] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[    5.651589] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    5.665970] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal link mode
[    9.852952] qca8k 37000000.mdio-mii:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[    9.976869] UBIFS (ubi0:1): Mounting in unauthenticated mode
[    9.977011] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 203
[   10.098357] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.098390] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.105168] UBIFS (ubi0:1): FS size: 88502272 bytes (84 MiB, 697 LEBs), max 708 LEBs, journal size 4444160 bytes (4 MiB, 35 LEBs)
[   10.115145] UBIFS (ubi0:1): reserved for root: 4180180 bytes (4082 KiB)
[   10.126764] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 470C67A1-EDBE-4E09-BB47-4CC91EB6C8D3, small LPT model
[   10.134360] mount_root: overlay filesystem has not been fully initialized yet
[   10.144966] mount_root: switching to ubifs overlay
[   10.370941] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.443656] qca8k 37000000.mdio-mii:10 lan1: Link is Down
[   10.452725] procd: - early -
[   10.452836] procd: - watchdog -
[   10.454834] procd: Watchdog has previously reset the system
[   10.988482] procd: - watchdog -
[   10.988563] procd: Watchdog has previously reset the system
[   10.990628] procd: - ubus -
[   11.069617] procd: - init -
[   11.443972] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.465808] Loading modules backported from Linux version v6.11.2-0-g7aa21fec187b
[   11.465846] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
[   11.611409] PPP generic driver version 2.4.2
[   11.611965] NET: Registered PF_PPPOX protocol family
[   11.623882] ath10k_pci 0001:01:00.0: assign IRQ: got 32
[   11.624412] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[   11.624516] ath10k_pci 0001:01:00.0: enabling bus mastering
[   11.624994] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x43a1e000
[   11.625162] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.690355] urngd: v1.0.2 started.
[   12.223807] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   12.223858] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   12.234475] ath10k_pci 0001:01:00.0: firmware ver 10.4-3.9.0.2-00157 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 6cdc6ff9
[   14.522183] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 0bfe5c35
[   18.308766] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 512 raw 0 hwcrypto 1
[   18.391568] ath: EEPROM regdomain: 0x0
[   18.391580] ath: EEPROM indicates default country code should be used
[   18.391584] ath: doing EEPROM country->regdmn map search
[   18.391593] ath: country maps to regdmn code: 0x3a
[   18.391599] ath: Country alpha2 being used: US
[   18.391604] ath: Regpair used: 0x3a
[   18.448292] ath10k_pci 0000:01:00.0: assign IRQ: got 34
[   18.448760] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[   18.448857] ath10k_pci 0000:01:00.0: enabling bus mastering
[   18.449308] qcom-pcie 1b500000.pci: msi#1 address_hi 0x0 address_lo 0x43a20000
[   18.449464] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   18.758756] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   18.758806] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   18.769656] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.9.0.2-00157 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 6cdc6ff9
[   21.064399] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 0bfe5c35
[   24.859672] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 512 raw 0 hwcrypto 1
[   24.940801] ath: EEPROM regdomain: 0x0
[   24.940811] ath: EEPROM indicates default country code should be used
[   24.940816] ath: doing EEPROM country->regdmn map search
[   24.940825] ath: country maps to regdmn code: 0x3a
[   24.940832] ath: Country alpha2 being used: US
[   24.940837] ath: Regpair used: 0x3a
[   24.990506] kmodloader: done loading kernel modules from /etc/modules.d/*
[   29.415865] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[   29.422744] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   29.423442] dwmac1000: Master AXI performs any burst length
[   29.430018] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   29.445241] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   29.445386] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   29.453192] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   29.460935] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   29.494980] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   29.495683] dwmac1000: Master AXI performs any burst length
[   29.502274] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[   29.517495] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   29.517640] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[   29.530427] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[   29.532827] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   29.543433] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal [   29.901748] qca8k 37000000.mdio-mii:10 lan4: entered allmulticast mode
[   29.914469] qca8k 37000000.mdio-mii:10 lan4: entered promiscuous mode
[   30.505547] ath: EEPROM regdomain: 0x833a
[   30.505583] ath: EEPROM indicates we should expect a country code
[   30.508628] ath: doing EEPROM country->regdmn map search
[   30.514619] ath: country maps to regdmn code: 0x37
[   30.520089] ath: Country alpha2 being used: GB
[   30.524597] ath: Regpair used: 0x37
[   30.529131] ath: regdomain 0x833a dynamically updated by user
[   30.532439] ath: EEPROM regdomain: 0x833a
[   30.538395] ath: EEPROM indicates we should expect a country code
[   30.542311] ath: doing EEPROM country->regdmn map search
[   30.548454] ath: country maps to regdmn code: 0x37
[   30.553763] ath: Country alpha2 being used: GB
[   30.558465] ath: Regpair used: 0x37
[   30.562796] ath: regdomain 0x833a dynamically updated by user
[   33.044145] qca8k 37000000.mdio-mii:10 lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[   33.764008] qca8k 37000000.mdio-mii:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   34.004104] qca8k 37000000.mdio-mii:10 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[   38.145434] ath10k_pci 0001:01:00.0: Unknown eventid: 36933

(I've removed a few lines to get it <32k)

I will monitor and see what happens.

brada4 · December 26, 2024, 12:44am

you can leav€ only sections with \ ath dealing with device startup then any eventual crash, maybe few lines before.

Scope · December 26, 2024, 12:13pm

Thing seems to be working fine, with less entries in the log.. I did have these overnight, but I suspect they are nothing to worry about?

(although it would be good to resolve them, if possible)

Thu Dec 26 00:22:20 2024 kern.warn kernel: [  727.197550] ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
Thu Dec 26 00:22:22 2024 kern.warn kernel: [  729.277962] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 5 tid 0
Thu Dec 26 00:22:22 2024 kern.warn kernel: [  729.278019] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 5 tid 0
Thu Dec 26 00:22:22 2024 kern.warn kernel: [  729.284105] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 5 tid 0
Thu Dec 26 00:22:22 2024 kern.warn kernel: [  729.291290] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 5 tid 0
Thu Dec 26 00:22:22 2024 kern.warn kernel: [  729.298550] ath10k_pci 0000:01:00.0: Invalid peer id 5 peer stats buffer
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.936297] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.936347] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.942432] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.949713] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.957121] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.964050] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.971299] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.978525] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.985700] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 01:51:11 2024 kern.warn kernel: [ 6058.992877] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 11 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.211646] ath10k_warn: 1256 callbacks suppressed
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.211666] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.216037] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.223137] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.230917] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.237041] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.244180] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.251434] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.258985] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.266158] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 11:57:58 2024 kern.warn kernel: [42465.273553] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 12 tid 0
Thu Dec 26 12:05:37 2024 kern.warn kernel: [42924.806616] ath10k_warn: 217 callbacks suppressed
Thu Dec 26 12:05:37 2024 kern.warn kernel: [42924.806629] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 17 tid 0
Thu Dec 26 12:05:37 2024 kern.warn kernel: [42924.810336] ath10k_pci 0000:01:00.0: failed to lookup txq for peer_id 17 tid 0

brada4 · December 26, 2024, 12:16pm

Lets check if drivers are consistent and well, yes, some noise comes from them but no crash.

opkg list-installed | grep ath10k

Scope · December 26, 2024, 1:27pm

root@R7800:~# opkg list-installed | grep ath10k
ath10k-board-qca9984 - 20241110-r1
ath10k-firmware-qca9984 - 20241110-r1
kmod-ath10k - 6.6.67.6.11.2-r1

brada4 · December 26, 2024, 3:13pm

All correct