[Ramips MT7621] FreeWRT 20.12 - Master branch based

Getting " 500 - Error interno del servidor. Hay un problema con el recurso que busca y no se puede mostrar." when trying to access http://downloads.freewrt.tk/

How is the 2.4GHz radio? Last I tried before Christmas it was unreliable.

Server is under maintenance. In a few hours it will be available again.

I have not tested the mt76 driver. My device does not have wifi.

Excellent work, thank you!

I'm a bit puzzled about how to configure DSA for a "router on a stick" setup.

I have an x86 OpenWrt mini PC with just single ethernet port tagged for WAN1 (eth0.10), WAN2 (eth0.20) and LAN (eth0.30). It was connected to my EdgeRouter-X, that basically served as a Level-2 switch under OpenWrt 19.07, with VLANs configured like this:

  • The main ISP WAN1 line was connected to ERX's untagged port LAN1 (PVID 10)
  • The backup 4G WAN2 line was connected to ERX's untagged port LAN2 (PVID 20)
  • My home LAN was connected to ERX's untagged port LAN3 (PVID 30)
  • The management-only port was on ERX's untagged LAN4 (PVID 50)
  • The trunk port (from the mini PC router) was connected tp ERX's tagged port WAN (tagged for VLAN10, 20, 30, 50).

That worked well, besides my ERX was occasional freezing due the infamous MT7621 issue.

Is it possible to replicate this configuration with a DSA build like FreeWRT?

The Kernel's "DSA switch configuration from userspace" docs feel a bit scarce for a novice. Should I proceed with the second option, "Configuration without tagging support"?

Thanks a lot of any thoughts!

Solved it.

I have landed on this topic while searching for problems with my Xiaomi Mi Router 3G related to unstable wireless on radio 2.4GHz... Maybe I could give a try to your build and post results about the performance, etc.

For upgradring from 19.7.x I guess that it's just a matter of uploading sysupgrade image and don't keep settings, right ?

@apocalypse I'm getting "Signature check failed" while trying to install packages. I would like to test performance with iperf3. Do you know how to solve this?

Edit: I figured that removing "option check_signature" from /etc/opkg.conf just works. Not the best solution but...

Test wireless on 2.4Ghz

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec   139 MBytes  19.5 Mbits/sec                  sender
[  5]   0.00-60.02  sec   139 MBytes  19.4 Mbits/sec                  receiver
[  7]   0.00-60.00  sec   109 MBytes  15.3 Mbits/sec                  sender
[  7]   0.00-60.02  sec   109 MBytes  15.2 Mbits/sec                  receiver
[  9]   0.00-60.00  sec   111 MBytes  15.5 Mbits/sec                  sender
[  9]   0.00-60.02  sec   111 MBytes  15.5 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec   112 MBytes  15.6 Mbits/sec                  sender
[ 11]   0.00-60.02  sec   111 MBytes  15.6 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec   123 MBytes  17.2 Mbits/sec                  sender
[ 13]   0.00-60.02  sec   123 MBytes  17.1 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec   131 MBytes  18.4 Mbits/sec                  sender
[ 15]   0.00-60.02  sec   131 MBytes  18.3 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec   726 MBytes   102 Mbits/sec                  sender
[SUM]   0.00-60.02  sec   724 MBytes   101 Mbits/sec                  receiver

Test wireless on 5Ghz

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec   638 MBytes  89.1 Mbits/sec                  sender
[  5]   0.00-60.05  sec   637 MBytes  89.0 Mbits/sec                  receiver
[  7]   0.00-60.00  sec   616 MBytes  86.1 Mbits/sec                  sender
[  7]   0.00-60.05  sec   615 MBytes  85.9 Mbits/sec                  receiver
[  9]   0.00-60.00  sec   669 MBytes  93.5 Mbits/sec                  sender
[  9]   0.00-60.05  sec   668 MBytes  93.4 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec   546 MBytes  76.4 Mbits/sec                  sender
[ 11]   0.00-60.05  sec   546 MBytes  76.2 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec   551 MBytes  77.1 Mbits/sec                  sender
[ 13]   0.00-60.05  sec   551 MBytes  76.9 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec   647 MBytes  90.4 Mbits/sec                  sender
[ 15]   0.00-60.05  sec   646 MBytes  90.3 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec  3.58 GBytes   513 Mbits/sec                  sender
[SUM]   0.00-60.05  sec  3.58 GBytes   512 Mbits/sec                  receiver

Client about 1m far from router.

I will be using the router as AP during the following days to see if my problems with 2.4Ghz are gone or not.

Sorry for the inconvenient. Which version are you using? The repository key must be the same as the build key, since the packages and the repository were compiled at the same time as the firmwares.

I will check and make sure in the next version. I will build a new version in the next few days.

I would like to test performance with iperf3

What client are you using for testing? Is the iperf3 server running on the router itself or on a wired PC?

It is better to run the server on a separate machine, to not saturate the router's CPU. In any case the 5GHz tests are good, i assume the client it's 2x2 MIMO with 80MHz channel width.

For 2.4GHz 2x2 MIMO with 40MHz channel width (if the client supports it, most smartphones for example only support 20MHz channel width at 2.4GHz) more than 200Mbps could be achieved, if the 2.4GHz radio from Mediatek and drivers are good.

20.12.1

I realized that using router as server is not ideal scenario... I'm using wired gigabit iMac as server.

Tests over 2.4Ghz were done only at 20MHz channel width. For the moment I'm very interested to see if I have the same strange behaviour while using router as AP. On 19.7.x from time to time my 2.4Ghz clients showed connected to the station but ping were lost... Will try 40Mhz after my tests then, but I think that my MBP early 2015 has not MUMIMO support... need to check first.

After two days of testing as AP, I'm having the same issue with 2.4Ghz band. I don't understand why suddenly you can't ping a client that shows connected to the station from PC. If in that precise moment I connect with SSH to the AP and ping from it, suddenly it start responding from both pings. :man_shrugging:

1 Like

New version uploaded, based on r16282 with latest mt76 drivers. Changes from 20.12.1 to 20.12.2:

Fixed repository/build key signature.

kernel: bump 5.4 to 5.4.105
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=e7fa97b326e596f64c4b9965c6f6c3773944c2c6

kernel: add defaults for new SELinux options
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=a21be2a70365363f5dd08efd6c629a254cc37170

kernel: fix busy wait loop in mediatek PPE code
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=3da4acaa7bba185489b968a140ecf327169db0bd

kernel: add compatibility with upstream threaded NAPI patch
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=3d1ea0d77f9d313c85ee82ef90082083f9e0176e

kernel: backports: mt7530: fix TRGMII mode after reset
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=680f91d0e5444d58815af03bf41c12592438f9d8

dnsmasq: switch to ubus-based hotplug call
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=aed95c4cb8d5a55a795910a759d08e1393f8d967

dnsmasq: Bump to v2.84
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=db00f312d3ae700adbecc4d1b5d7476cc8ef7f92

ca-certicficates: Update to version 20210119
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ea1cdd19013b17ae5240f0622a028941a50cd15e

odhcpd: update to latest git HEAD
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1b484f1a125190b34fb37226b39d883ac85101d4

iptables: update to 1.8.7
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=abe348168b282786208a1959d2a80794fdd82f2b

hostapd: fix P2P group information processing vulnerability
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=7c8c4f1be648aff9f1072ee27a2cc8f6a4a788ef

hostapd: add forgotten patch for P2P vulnerability fix
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=43ff6e641e7c321ab3b67c43ba73a6877d8f0439

hostapd: add notifications for management frames
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=59fa9c28d60a265f69da046a688feadc4096ee36

hostapd: reconfigure wps credentials on reload
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=14b9100f1c6e4b403270fb2e285daa9d130e4cfd

hostapd: P2P: Fix a corner case in peer addition based on PD Request
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1ca5de13a153061feae260864d73d96f7c463785

procd: add hotplug-call dispatcher ubus objects
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=3010f16f44e20127816817d708dbe8d26657c0fd

procd: update to git HEAD
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ffeb37047e85a5efd96890db12710e9d60b4b76a

wolfssl: Backport fix for CVE-2021-3336
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1f559cafe5cc1193a5962d40a2d938c66c783171

wolfssl: bump to v4.7.0-stable
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d1dfb577f1c0d5b1f1fa35000c9ad7abdb7d10ed

iproute2: update to 5.11.0
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b048a305a3d3cbb5375e32757e70aa129b4c7c4f

igmpproxy: update to version 0.3
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=0c0c9c734d216b69f404a80eab4f9989a4fc9d42

mt76: update to the latest version
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=12b5f898f9222d35b80058fee5bd2ae935226070

ramips: mt7621: reorganize shared device definitions for Xiaomi
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=5a46b718260fba4253ea0153d93a02a7c3a7b710

ramips: mt7621: create DTSI for Xiaomi NAND devices
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=93be5926a2c2ebda05486a43f998a2ee38d32e61

ramips: mt7621: add support for Xiaomi Mi Router 4
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c2a7bb520a0fb107984ad3757174d391796cd222

ramips: fix port labels for Xiaomi Mi Router 4
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b3eccbca7c476c967af8e56c73061df2893ded7d

ramips: use lzma-loader on zbtlink devices
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ff9846dbb94342b8b3e07ad54ec2e9a7a48e3f3e

ramips: remove generic profiles
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=703fd8aef4b33cccbc3af5a1cb92209a8e201754

ramips: add support for ELECOM WRC-2533GHBK-I
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=eb11cd9ea3822b34df6260b1dd40fc4f0866b804

ramips: add support for Hi-Link HLK-7688A
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ddafcc79473249089ffd4c2de8159af2a27e5683

ramips: add support for UniElec U7621-01
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=4a1803978575295f8cec0813cc74b3448730feac

ramips: replace full-text licenses by SPDX identifier
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=3f4d1dad0009d3fdd50aecb78c6d896ab58b83c7

ramips: add support for I-O DATA WN-DX1200GR
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=88fbddb49d7128ee565c65bcc1e72ae68c7c2635

ramips: mt7621: use preferred logic in lib/upgrade/iodata.sh
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1c0e13db43b41a1d527428b82bf88a032a916e84

ramips: disable default build for HooToo HT-TM02
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1e9afcca56190e7f9d9b7b1e2b7fcb007243f5b0

ramips: add support for JCG Y2
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=82032f350991af08a918f0fcaac81ff82e836d88

ramips: add support for Cudy WR1300
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=cd2b661453a8a2b8260dfb9b9c0dc5297b981331

ramips: add support for ELECOM WRC-1167FS
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=08768b44d9b6983ae8d2b96434225fef1f5f664c

ramips: remove factory image for TP-Link Archer C2 v1
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ad5e29d38a48ce6ffbcabaf5d83bc76a64dfbe56

ramips: manage low reset lines
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=69551a244292f5baf0aee205ec6b891a03f1ee15

ramips: remove factory image for TP-Link Archer C20 v1
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=0265cba40ad4f2b8ff4473ada123c35b53ffd97a

ramips: mt7621: add TP-Link EAP235-Wall support
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=1e75909a35a2b361cdfdfcf18a26ad61271b174e

ramips: use lzma-loader for Wevo devices
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ca6954e2dc3faa32eec54b93bda996c874409675

ramips: overwrite reset gpio properties in EX6150 DTS
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=af1b6799c6ec9af7a30d63a5ddfed20f443b991c

ramips: correct/add Phicomm K2x WAN/label MAC address
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=55263ffedbe1d20f005febbc973a7353240d1741

ramips: drop redundant definitions of serial0 in aliases
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=86a4d7802272707c19864ebb56518cc7aa64102f

ramips: move aliases to the top in SoC DTSI files
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d4520d75a142db901d748c4f07e3ff72916bfa91

ramips: fix Phicomm PSG1218A switch port labels
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=567a88e4b99f9e1b647588de0319357e688ce016

ramips: improve gpio control for Phicomm PSG1218
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d1176ad95a82495c3745465da902de11ea2f88ea

ramips: mt7621: enable SX150x driver
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=773949c152f7378a303919e790210113012fea04

ramips: overwrite reset gpio properties in DIR-860L DTS
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=06356f00200639c48d95330e633965957b0347ab

ramips: remove obsolete mx25l25635f compatible hack
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=06af45ec0502d5cb0529ac46fcb34c4c63394723

ramips: add support for ZTE MF283+
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=59d065c9f81c4d1a89464d071134a50529449f34

ramips: fix partition layout of hiwifi hc5x61
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=df1e5d6463459637e2c1b39b11a05a45ed2322d4

ramips: rename mtk-hsdma to hsdma-mt7621
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=58ad113087b3db7567507202b94d94756056a455

ramips: fix broken UniFi 6 Lite image
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=ac5675ec8f63d8cce5af066fa1fcf3906b9e8b2c

ramips: improve GPIO pin control for HC5x61
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=a94a20373ba0c817ddb03da0bf15af6c8d6a09ff

ramips: move spi-nor-add-gd25q512 patch to generic
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=f65b0afadb5398d1c1957c9b6a1c3bc735ff7a60

Thanks @apocalypse I will give a try when I get some free time.

I have a Netgear R6230. I have to use the firmware for the R6220 as there is no R6230 yet for OpenWRT. I tried this firmware, 20.12.2 i think it was. It had horrible Ethernet speed. Only about 250Mb's, I played around with packet steering as well as hardware/software offloading and it didn't help. In fact those options made things worse. I use this router as a stupid wireless access point and have it setup to get a DHCP address from my main router via gigabit Ethernet. This works great on 19.07.7 but in this firmware I was unable to make DHCP work. Every time I tried to use DHCP instead of static, the router would lockup and my computer would no longer sense an Ethernet connection. I never even got to try the wireless out. At this point I decided to go back to 19.07.7. I very stupidly neglected to get any logs for you before downgrading to 19.07.7 or I would have posted them. My bad on that one. I will keep a breast of this thread as it interests me greatly and if you release updated firm wares I will try her again. This R6230 is not a main piece of my network, its one of my hobby routers and Id love to give your firm wares a second shot in the future. I also have a Netgear R6120 I can fool around with. Same hobby router situation applies to this as well.

Again, my apologies about the lack of logs.

LAN -> LAN

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[  5]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[  7]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[  7]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[  9]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[  9]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[ 11]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[ 13]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  sender
[ 15]   0.00-60.00  sec  1.07 GBytes   153 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec  6.41 GBytes   918 Mbits/sec                  sender
[SUM]   0.00-60.00  sec  6.41 GBytes   918 Mbits/sec                  receiver
LAN -> WLAN 2.4Ghz 20 Mhz

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec  64.0 MBytes  8.94 Mbits/sec                  sender
[  5]   0.00-60.00  sec  63.8 MBytes  8.92 Mbits/sec                  receiver
[  7]   0.00-60.00  sec  62.9 MBytes  8.79 Mbits/sec                  sender
[  7]   0.00-60.00  sec  62.7 MBytes  8.77 Mbits/sec                  receiver
[  9]   0.00-60.00  sec  69.3 MBytes  9.69 Mbits/sec                  sender
[  9]   0.00-60.00  sec  69.2 MBytes  9.67 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec  58.2 MBytes  8.13 Mbits/sec                  sender
[ 11]   0.00-60.00  sec  58.1 MBytes  8.12 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec  65.4 MBytes  9.14 Mbits/sec                  sender
[ 13]   0.00-60.00  sec  65.2 MBytes  9.12 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec  68.0 MBytes  9.50 Mbits/sec                  sender
[ 15]   0.00-60.00  sec  67.9 MBytes  9.49 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec   388 MBytes  54.2 Mbits/sec                  sender
[SUM]   0.00-60.00  sec   387 MBytes  54.1 Mbits/sec                  receiver
LAN -> WLAN 2.4Ghz 40 Mhz

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec  67.4 MBytes  9.42 Mbits/sec                  sender
[  5]   0.00-60.00  sec  67.3 MBytes  9.41 Mbits/sec                  receiver
[  7]   0.00-60.00  sec  53.7 MBytes  7.51 Mbits/sec                  sender
[  7]   0.00-60.00  sec  53.7 MBytes  7.50 Mbits/sec                  receiver
[  9]   0.00-60.00  sec  60.2 MBytes  8.42 Mbits/sec                  sender
[  9]   0.00-60.00  sec  60.1 MBytes  8.41 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec  56.3 MBytes  7.87 Mbits/sec                  sender
[ 11]   0.00-60.00  sec  56.1 MBytes  7.85 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec  63.1 MBytes  8.82 Mbits/sec                  sender
[ 13]   0.00-60.00  sec  63.0 MBytes  8.81 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec  50.3 MBytes  7.03 Mbits/sec                  sender
[ 15]   0.00-60.00  sec  50.2 MBytes  7.02 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec   351 MBytes  49.1 Mbits/sec                  sender
[SUM]   0.00-60.00  sec   350 MBytes  49.0 Mbits/sec                  receiver
LAN -> WLAN 5Ghz

[ ID] Interval           Transfer     Bitrate
[  5]   0.00-60.00  sec   611 MBytes  85.5 Mbits/sec                  sender
[  5]   0.00-60.00  sec   611 MBytes  85.5 Mbits/sec                  receiver
[  7]   0.00-60.00  sec   643 MBytes  89.8 Mbits/sec                  sender
[  7]   0.00-60.00  sec   642 MBytes  89.8 Mbits/sec                  receiver
[  9]   0.00-60.00  sec   633 MBytes  88.5 Mbits/sec                  sender
[  9]   0.00-60.00  sec   633 MBytes  88.5 Mbits/sec                  receiver
[ 11]   0.00-60.00  sec   623 MBytes  87.1 Mbits/sec                  sender
[ 11]   0.00-60.00  sec   623 MBytes  87.1 Mbits/sec                  receiver
[ 13]   0.00-60.00  sec   643 MBytes  90.0 Mbits/sec                  sender
[ 13]   0.00-60.00  sec   643 MBytes  90.0 Mbits/sec                  receiver
[ 15]   0.00-60.00  sec   461 MBytes  64.5 Mbits/sec                  sender
[ 15]   0.00-60.00  sec   461 MBytes  64.5 Mbits/sec                  receiver
[SUM]   0.00-60.00  sec  3.53 GBytes   505 Mbits/sec                  sender
[SUM]   0.00-60.00  sec  3.53 GBytes   505 Mbits/sec                  receiver

Seems that the wireless performance is a little worst with FreeWRT 20.12.2.

It seems that a good boost with AES128/256CBC and SHA1/256 with that patch, can it be added to firmware?

Try 100 channel, in my case it about 500 mbit...

When trying to add QMI modem (and any of new interfaces), there is an error:

An error occurred while saving the form:

section_id is not defined

Seems that related to:

1 Like

Thanks for reporting. I will make a new build as soon as i can.

1 Like

I am having troubles compiling. The other builds i make on SSD but to not crush it with so much writings, this time i have tried it on HDD but the three times i'l try the compilation has hang near the end. Moving all files to SSD to compile on it.

3 Likes