I recently acquired an R7800 router, which has the issue where neither the 2.4 GHz nor the 5 GHz Wi-Fi signals can be detected by any device, even though both radios are enabled by default. This issue occurred when the router was running the stock OEM firmware.
I then attempted to flash the router with OpenWRT firmware to see if the same issue persisted with the OEM firmware. The result was that the 2.4 GHz Wi-Fi signal became detectable when the radio was enabled via the LuCI interface. However, the 5 GHz radio did not appear in the wireless tab in LuCI.
What I have done so far includes trying to revert to the stock firmware using the TFTP method and reflashing with several OpenWRT versions (22.05.3, 22.05.5, and 24.10.0-rc4). I also manually added configurations in /etc/config/wireless. The 5 GHz radio appeared in the LuCI tab, but the device showed up as "generic unknown." Additionally, I removed the Candela driver and replaced it with a non-Candela driver, but the result was still the same.
What I know is that there is a message in the dmesg logs indicating that the radio is detected, but its status cannot UP. Below, I will attach the dmesg details from my device.
I hope this issue is related to software and I would appreciate assistance and analysis from experts. Thank you for reading my post.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.150 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 22 22:09:42 2024
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000005fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s19788 r8192 d21172 u49152
[ 0.000000] pcpu-alloc: s19788 r8192 d21172 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 474152K/491520K available (6837K kernel code, 619K rwdata, 1088K rodata, 1024K init, 245K bss, 17368K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000002] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000025] Switching to timer-based delay loop, resolution 160ns
[ 0.000338] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000373] CPU: Testing write buffer coherency: ok
[ 0.000431] pid_max: default: 32768 minimum: 301
[ 0.001272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001300] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003318] qcom_scm: convention: smc legacy
[ 0.004647] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.004850] rcu: Hierarchical SRCU implementation.
[ 0.005461] smp: Bringing up secondary CPUs ...
[ 0.007490] smp: Brought up 1 node, 2 CPUs
[ 0.007516] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.007533] CPU: All CPU(s) started in SVC mode.
[ 0.020242] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.020432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.020469] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.020823] pinctrl core: initialized pinctrl subsystem
[ 0.022885] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.023239] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.024766] thermal_sys: Registered thermal governor 'step_wise'
[ 0.026951] cpuidle: using governor ladder
[ 0.027030] cpuidle: using governor menu
[ 0.046405] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 0.080455] s1a: Bringing 0uV into 1050000-1050000uV
[ 0.080687] s1a: supplied by regulator-dummy
[ 0.080885] s1b: Bringing 0uV into 1050000-1050000uV
[ 0.081117] s1b: supplied by regulator-dummy
[ 0.081259] s2a: Bringing 0uV into 775000-775000uV
[ 0.081460] s2a: supplied by regulator-dummy
[ 0.081625] s2b: Bringing 0uV into 775000-775000uV
[ 0.081881] s2b: supplied by regulator-dummy
[ 0.082452] usbcore: registered new interface driver usbfs
[ 0.082521] usbcore: registered new interface driver hub
[ 0.082607] usbcore: registered new device driver usb
[ 0.082669] pps_core: LinuxPPS API ver. 1 registered
[ 0.082756] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.082796] PTP clock support registered
[ 0.085040] clocksource: Switched to clocksource dg_timer
[ 0.086370] NET: Registered PF_INET protocol family
[ 0.086564] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.087548] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.087588] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.087617] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.087654] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.087713] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.087810] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.087843] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.088164] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.088220] PCI: CLS 0 bytes, default 64
[ 0.089348] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.096191] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.096215] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.203925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.206971] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
[ 0.207206] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
[ 0.207315] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
[ 0.207624] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.207671] qcom-pcie 1b500000.pci: Parsing ranges property...
[ 0.207710] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x0000000000
[ 0.207751] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
[ 0.328306] qcom-pcie 1b500000.pci: iATU unroll: disabled
[ 0.328327] qcom-pcie 1b500000.pci: Detected iATU regions: 8 outbound, 8 inbound
[ 1.355034] qcom-pcie 1b500000.pci: Phy link never came up
[ 1.355176] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 1.355198] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.355314] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.355362] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 1.355385] pci_bus 0000:00: scanning bus
[ 1.355437] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 1.355579] pci 0000:00:00.0: supports D1
[ 1.355598] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.355618] pci 0000:00:00.0: PME# disabled
[ 1.359131] pci_bus 0000:00: fixups for bus
[ 1.359156] PCI: bus0: Fast back to back transfers disabled
[ 1.359176] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 1.359311] pci_bus 0000:01: scanning bus
[ 1.362443] pci_bus 0000:01: fixups for bus
[ 1.362453] PCI: bus1: Fast back to back transfers enabled
[ 1.362471] pci_bus 0000:01: bus scan returning with max=01
[ 1.362489] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 1.362509] pci_bus 0000:00: bus scan returning with max=ff
[ 1.362529] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.362719] pcieport 0000:00:00.0: assign IRQ: got 43
[ 1.362855] qcom-pcie 1b500000.pci: msi#0 address_hi 0x0 address_lo 0x4323be98
[ 1.363633] pcieport 0000:00:00.0: AER: enabled with IRQ 44
[ 1.363802] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 1.363821] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 1.363834] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 1.363847] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 1.363861] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 1.363873] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 1.363886] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 1.363900] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 1.363912] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0xfff0)
[ 1.363925] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 1.363938] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 1.363951] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 1.363963] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 1.363976] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 1.363988] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 1.364001] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012b)
[ 1.364603] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
[ 1.364805] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
[ 1.364909] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
[ 1.365342] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 1.365387] qcom-pcie 1b700000.pci: Parsing ranges property...
[ 1.365426] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0000000000
[ 1.365466] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
[ 1.489871] qcom-pcie 1b700000.pci: iATU unroll: disabled
[ 1.489892] qcom-pcie 1b700000.pci: Detected iATU regions: 8 outbound, 8 inbound
[ 1.592649] qcom-pcie 1b700000.pci: Link up
[ 1.592785] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 1.592805] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.592826] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
[ 1.592844] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 1.592865] pci_bus 0001:00: scanning bus
[ 1.592915] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 1.593042] pci 0001:00:00.0: supports D1
[ 1.593060] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 1.593078] pci 0001:00:00.0: PME# disabled
[ 1.596629] pci_bus 0001:00: fixups for bus
[ 1.596653] PCI: bus0: Fast back to back transfers disabled
[ 1.596673] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
[ 1.596805] pci_bus 0001:01: scanning bus
[ 1.597032] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 1.597228] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.598102] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.598144] pci 0001:01:00.0: PME# disabled
[ 1.598385] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.601813] pci_bus 0001:01: fixups for bus
[ 1.601873] PCI: bus1: Fast back to back transfers disabled
[ 1.601891] pci_bus 0001:01: bus scan returning with max=01
[ 1.601908] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
[ 1.601928] pci_bus 0001:00: bus scan returning with max=ff
[ 1.601952] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 1.601979] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 1.602084] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 1.602108] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 1.602278] pcieport 0001:00:00.0: assign IRQ: got 45
[ 1.602388] qcom-pcie 1b700000.pci: msi#0 address_hi 0x0 address_lo 0x4322f498
[ 1.603004] pcieport 0001:00:00.0: AER: enabled with IRQ 46
[ 1.603119] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
[ 1.603136] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
[ 1.603151] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
[ 1.603164] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
[ 1.603176] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
[ 1.603191] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 1.603203] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
[ 1.603216] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
[ 1.603229] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
[ 1.603244] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
[ 1.603257] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 1.603269] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 1.603282] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 1.603294] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
[ 1.603307] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 1.603319] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3012d)
[ 1.606672] krait-cc soc:clock-controller: CPU0 @ 800000 KHz
[ 1.606701] krait-cc soc:clock-controller: CPU1 @ Undefined rate. Forcing new rate.
[ 1.606838] krait-cc soc:clock-controller: CPU1 @ 384000 KHz
[ 1.606858] krait-cc soc:clock-controller: L2 @ Undefined rate. Forcing new rate.
[ 1.607048] krait-cc soc:clock-controller: L2 @ 384000 KHz
[ 1.611083] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.612883] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.615204] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.615256] msm_serial 16340000.serial: uartclk = 7372800
[ 1.615416] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 47, base_baud = 460800) is a MSM
[ 1.615457] msm_serial: console setup on port #0
[ 2.492368] printk: console [ttyMSM0] enabled
[ 2.497529] msm_serial: driver initialized
[ 2.506888] loop: module loaded
[ 2.508340] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[ 2.508840] nand: Micron MT29F1G08ABBEAH4
[ 2.515505] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.519431] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 2.526913] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[ 2.533700] OF: Bad cell count for /soc/nand-controller@1ac00000/nand@0/partitions
[ 2.541829] Creating 8 MTD partitions on "qcom_nand.0":
[ 2.548746] 0x000000000000-0x000000c80000 : "qcadata"
[ 2.572123] 0x000000c80000-0x000001180000 : "APPSBL"
[ 2.579704] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 2.580962] 0x000001200000-0x000001340000 : "art"
[ 2.586097] 0x000001340000-0x000001480000 : "artbak"
[ 2.590888] 0x000001480000-0x000001880000 : "kernel"
[ 2.599741] 0x000001880000-0x000007900000 : "ubi"
[ 2.736619] 0x000007900000-0x000008000000 : "reserve"
[ 2.768442] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 3.591729] ar8327: qca,phy-rgmii-en is not specified
[ 3.592718] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 3.595870] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 3.603634] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 3.609885] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.615887] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 3.623283] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 3.629185] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 3.636897] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 3.644720] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 3.650611] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 3.657994] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 3.664688] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 3.672324] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 3.679353] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.687242] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 3.694119] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 3.701454] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 3.707887] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 3.714085] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 3.721641] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 3.727443] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 3.735089] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 3.743058] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 3.748863] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 3.756233] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 3.762952] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 3.770572] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 3.777610] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 3.785494] i2c_dev: i2c /dev entries driver
[ 3.795732] sdhci: Secure Digital Host Controller Interface driver
[ 3.796630] sdhci: Copyright(c) Pierre Ossman
[ 3.802619] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.814117] NET: Registered PF_INET6 protocol family
[ 3.815640] Segment Routing with IPv6
[ 3.818180] In-situ OAM (IOAM) with IPv6
[ 3.821789] NET: Registered PF_PACKET protocol family
[ 3.825839] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.830986] 8021q: 802.1Q VLAN Support v1.8
[ 3.843804] Registering SWP/SWPB emulation handler
[ 3.875329] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 3.889007] UBI: auto-attach mtd6
[ 3.889029] ubi0: attaching mtd6
[ 3.921159] UBI: EOF marker found, PEBs from 35 will be erased
[ 4.015480] random: crng init done
[ 4.017201] ubi0: scanning is finished
[ 4.039945] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 715 LEBs
[ 4.040393] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 4.045421] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.050829] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.057662] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.064457] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 4.071283] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.077541] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1711145382
[ 4.084511] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 4.093932] ubi0: background thread "ubi_bgt0d" started, PID 92
[ 4.094600] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.108754] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.123738] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.125232] Freeing unused kernel image (initmem) memory: 1024K
[ 4.315852] Run /sbin/init as init process
[ 4.315912] with arguments:
[ 4.315916] /sbin/init
[ 4.315920] with environment:
[ 4.315922] HOME=/
[ 4.315925] TERM=linux
[ 4.585931] init: Console is alive
[ 4.586092] init: - watchdog -
[ 4.588362] init: Watchdog has previously reset the system
[ 5.282335] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.343710] pstore: Using crash dump compression: deflate
[ 5.344640] printk: console [ramoops-1] enabled
[ 5.348162] pstore: Registered ramoops as persistent store backend
[ 5.352427] ramoops: using 0x40000@0x42100000, ecc: 0
[ 5.359804] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.366593] SCSI subsystem initialized
[ 5.373151] libata version 3.00 loaded.
[ 5.374744] ahci 29000000.sata: supply ahci not found, using dummy regulator
[ 5.374871] ahci 29000000.sata: supply phy not found, using dummy regulator
[ 5.381345] ahci 29000000.sata: supply target not found, using dummy regulator
[ 5.388291] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 5.395156] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 5.400678] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 5.410375] scsi host0: ahci
[ 5.417683] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 32
[ 5.747191] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.748899] fsl-ehci: Freescale EHCI Host controller driver
[ 5.752003] ehci-platform: EHCI generic platform driver
[ 5.760061] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.762521] ohci-platform: OHCI generic platform driver
[ 5.901604] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.901653] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.906180] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 5.913572] xhci-hcd xhci-hcd.0.auto: irq 51, io mem 0x10000000
[ 5.923127] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.928884] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.934372] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 5.942364] hub 1-0:1.0: USB hub found
[ 5.948590] hub 1-0:1.0: 1 port detected
[ 5.952481] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.957221] hub 2-0:1.0: USB hub found
[ 5.964420] hub 2-0:1.0: 1 port detected
[ 5.968264] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.972049] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 5.977531] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000008002010010
[ 5.984915] xhci-hcd xhci-hcd.1.auto: irq 52, io mem 0x11000000
[ 5.994462] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.000238] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 6.005797] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 6.013619] hub 3-0:1.0: USB hub found
[ 6.019937] hub 3-0:1.0: 1 port detected
[ 6.023825] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.028160] hub 4-0:1.0: USB hub found
[ 6.035836] hub 4-0:1.0: 1 port detected
[ 6.040935] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.050474] init: - preinit -
[ 7.458243] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 7.458925] dwmac1000: Master AXI performs any burst length
[ 7.465464] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 7.480707] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 7.480825] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 7.489035] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 7.495967] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 7.504164] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 7.513347] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[ 9.644182] UBIFS (ubi0:1): default file-system created
[ 9.644948] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 9.655383] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 192
[ 9.721800] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 9.721829] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.728669] UBIFS (ubi0:1): FS size: 89391104 bytes (85 MiB, 704 LEBs), max 715 LEBs, journal size 4444160 bytes (4 MiB, 35 LEBs)
[ 9.738563] UBIFS (ubi0:1): reserved for root: 4222162 bytes (4123 KiB)
[ 9.750189] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID B5F24D48-C02A-4B29-A6A9-9B957CD7DDAB, small LPT model
[ 9.758217] mount_root: overlay filesystem has not been fully initialized yet
[ 9.768348] mount_root: switching to ubifs overlay
[ 9.779169] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 9.824199] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down
[ 9.878257] procd: - early -
[ 9.878352] procd: - watchdog -
[ 9.880270] procd: Watchdog has previously reset the system
[ 10.439915] procd: - watchdog -
[ 10.439999] procd: Watchdog has previously reset the system
[ 10.498055] procd: - ubus -
[ 10.554885] procd: - init -
[ 10.915888] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.977802] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 10.977836] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 11.056722] PPP generic driver version 2.4.2
[ 11.057552] NET: Registered PF_PPPOX protocol family
[ 11.070771] ath10k_pci 0001:01:00.0: assign IRQ: got 45
[ 11.070797] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x46.
[ 11.075624] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 11.077653] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 11.078046] qcom-pcie 1b700000.pci: msi#1 address_hi 0x0 address_lo 0x4322f498
[ 11.078174] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 11.124881] urngd: v1.0.2 started.
[ 11.738822] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 11.738867] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 11.749412] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 14.074394] ath10k_pci 0001:01:00.0: Loading BDF type 0
[ 14.082152] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 0bfe5c35
[ 17.635189] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 17.635264] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 17.719232] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 17.720101] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 18.012950] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
[ 18.098871] ath: EEPROM regdomain: 0x0
[ 18.098879] ath: EEPROM indicates default country code should be used
[ 18.098882] ath: doing EEPROM country->regdmn map search
[ 18.098888] ath: country maps to regdmn code: 0x3a
[ 18.098892] ath: Country alpha2 being used: US
[ 18.098896] ath: Regpair used: 0x3a
[ 18.103143] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 27.091562] ipq806x-gmac-dwmac 37400000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 27.092302] dwmac1000: Master AXI performs any burst length
[ 27.098801] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 27.114031] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 27.114152] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 27.121955] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode
[ 27.129915] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 27.138088] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 27.149090] br-lan: port 1(eth1.1) entered blocking state
[ 27.152268] br-lan: port 1(eth1.1) entered disabled state
[ 27.158099] device eth1.1 entered promiscuous mode
[ 27.163204] device eth1 entered promiscuous mode
[ 27.170565] br-lan: port 1(eth1.1) entered blocking state
[ 27.172666] br-lan: port 1(eth1.1) entered forwarding state
[ 27.189182] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 27.189870] dwmac1000: Master AXI performs any burst length
[ 27.196452] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 27.211655] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 27.211790] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 27.223249] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[ 27.226696] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 27.248832] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.176652] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
