I know, but luckily I have it.
I just tried to launch the board from usb...and...still kernel panic.
(IPQ) # usbboot dev 0
error reading partinfo...try to boot raw
Loading from USB device 0, partition 1: Name: Raw Type: U-Boot
BUG: failure at xhci-ring.c:489/abort_td()!
BUG!
resetting ...
Resetting with watch dog!
U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28)
U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
*** Warning - bad CRC, using default environment
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
131072 bytes read: OK
MMC Device 0 not found
cdp: get part failed for 0:HLOS
Net: MAC1 addr:b0:39:56:97:cb:c4
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:b0:39:56:97:cb:c3
eth0, eth1
Hit any key to stop autoboot: 0
Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual
nmrp server is stopped or failed !
Loading from device 0: nand0 (offset 0x1480000)
** check kernel image **
Verifying Checksum ... OK
** check rootfs image **
Verifying Checksum ... OK
MMC Device 0 not found
Loading from nand0, offset 0x1480000
Image Name: ARM OpenWrt Linux-5.4.154
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2750052 Bytes = 2.6 MiB
Load Address: 42208000
Entry Point: 42208000
Automatic boot of image at addr 0x44000000 ...
Image Name: ARM OpenWrt Linux-5.4.154
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2750052 Bytes = 2.6 MiB
Load Address: 42208000
Entry Point: 42208000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
mtdparts variable not set, see 'help mtdparts'
no partitions defined
defaults:
mtdids : nand0=msm_nand
mtdparts: none
info: "mtdparts" not set
Using machid 0x136c from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.154 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu s30220 r8192 d23028 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 474824K/491520K available (6268K kernel code, 196K rwdata, 920K rodata, 1024K init, 240K bss, 16696K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from 0xc0b00c18 with crng_init=0
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000024] Switching to timer-based delay loop, resolution 160ns
[ 0.000260] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000279] pid_max: default: 32768 minimum: 301
[ 0.000485] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000503] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001554] CPU: Testing write buffer coherency: ok
[ 0.002678] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.002857] rcu: Hierarchical SRCU implementation.
[ 0.003344] smp: Bringing up secondary CPUs ...
[ 0.005268] smp: Brought up 1 node, 2 CPUs
[ 0.005282] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005293] CPU: All CPU(s) started in SVC mode.
[ 0.015580] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.015727] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.015755] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.015905] pinctrl core: initialized pinctrl subsystem
[ 0.017038] NET: Registered protocol family 16
[ 0.017325] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.018660] cpuidle: using governor ladder
[ 0.018727] cpuidle: using governor menu
[ 0.049762] usbcore: registered new interface driver usbfs
[ 0.049841] usbcore: registered new interface driver hub
[ 0.049907] usbcore: registered new device driver usb
[ 0.049970] pps_core: LinuxPPS API ver. 1 registered
[ 0.049982] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.050022] PTP clock support registered
[ 0.050831] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.052049] clocksource: Switched to clocksource dg_timer
[ 0.052904] thermal_sys: Registered thermal governor 'step_wise'
[ 0.055319] NET: Registered protocol family 2
[ 0.055482] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.056348] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.056391] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.056435] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.056488] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.056589] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.056622] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.056865] NET: Registered protocol family 1
[ 0.056918] PCI: CLS 0 bytes, default 64
[ 0.058221] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.065165] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.065181] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.102524] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.104609] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.104758] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.104882] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.105149] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.105221] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.105259] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.327501] qcom-pcie 1b500000.pci: Link up
[ 0.327664] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.327688] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.327709] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.327727] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.327790] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000
[ 0.327957] pci 0000:00:00.0: supports D1
[ 0.327975] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.332160] PCI: bus0: Fast back to back transfers disabled
[ 0.332641] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.332996] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.334143] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.338501] PCI: bus1: Fast back to back transfers disabled
[ 0.338588] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.338614] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.338743] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.338767] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.339757] pcieport 0000:00:00.0: AER: enabled with IRQ 36
[ 0.340332] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.340461] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.340599] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.340858] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.340923] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.340961] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.569548] qcom-pcie 1b700000.pci: Link up
[ 0.569711] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.569731] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.569747] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.569801] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000
[ 0.569952] pci 0001:00:00.0: supports D1
[ 0.569967] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.574208] PCI: bus0: Fast back to back transfers disabled
[ 0.574562] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.574941] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.576177] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.576480] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.580604] PCI: bus1: Fast back to back transfers disabled
[ 0.580681] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.580704] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.580836] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.580856] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.581767] pcieport 0001:00:00.0: AER: enabled with IRQ 38
[ 0.584432] L2 @ QSB rate. Forcing new rate.
[ 0.584673] L2 @ 384000 KHz
[ 0.584861] CPU0 @ 800000 KHz
[ 0.584873] CPU1 @ QSB rate. Forcing new rate.
[ 0.585004] CPU1 @ 384000 KHz
[ 0.588774] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.591018] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.593617] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.593673] msm_serial 16340000.serial: uartclk = 7372800
[ 0.593747] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
[ 0.593787] msm_serial: console setup on port #0
[ 1.383212] printk: console [ttyMSM0] enabled
[ 1.388200] msm_serial: driver initialized
[ 1.397581] loop: module loaded
[ 1.399180] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.399534] nand: AMD/Spansion S34MS01G2
[ 1.406252] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.410142] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.417493] Creating 8 MTD partitions on "qcom_nand.0":
[ 1.424371] 0x000000000000-0x000000c80000 : "qcadata"
[ 1.434609] random: fast init done
[ 1.450929] 0x000000c80000-0x000001180000 : "APPSBL"
[ 1.460180] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 1.461988] 0x000001200000-0x000001340000 : "art"
[ 1.467300] 0x000001340000-0x000001480000 : "artbak"
[ 1.472065] 0x000001480000-0x000001880000 : "kernel"
[ 1.481653] 0x000001880000-0x000007900000 : "ubi"
[ 1.640952] 0x000007900000-0x000008000000 : "reserve"
[ 1.655039] libphy: ipq8064_mdio_bus: probed
[ 1.670274] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii
[ 2.518706] ar8327: qca,phy-rgmii-en is not specified
[ 2.519293] libphy: Fixed MDIO Bus: probed
[ 2.523563] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found
[ 2.526738] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found
[ 2.534780] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.540908] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.546966] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 2.554416] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.560158] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.567968] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.575841] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.581597] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.589056] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.595834] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.603363] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.610327] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.617487] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
[ 2.625282] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
[ 2.632451] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.638860] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.645253] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 2.652692] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.658420] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.666217] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.674120] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.679861] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.687303] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.694083] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.701560] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.708672] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.715820] i2c /dev entries driver
[ 2.725843] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.726749] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.734636] sdhci: Secure Digital Host Controller Interface driver
[ 2.741225] sdhci: Copyright(c) Pierre Ossman
[ 2.747566] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.754422] NET: Registered protocol family 10
[ 2.759045] Segment Routing with IPv6
[ 2.761975] NET: Registered protocol family 17
[ 2.765802] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.770175] 8021q: 802.1Q VLAN Support v1.8
[ 2.783206] Registering SWP/SWPB emulation handler
[ 2.812908] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 2.826773] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.827057] s1a: supplied by regulator-dummy
[ 2.830939] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.835382] s1b: supplied by regulator-dummy
[ 2.840133] s2a: Bringing 0uV into 775000-775000uV
[ 2.844568] s2a: supplied by regulator-dummy
[ 2.848991] s2b: Bringing 0uV into 775000-775000uV
[ 2.853599] s2b: supplied by regulator-dummy
[ 2.867977] UBI: auto-attach mtd6
[ 2.867997] ubi0: attaching mtd6
[ 2.932257] random: crng init done
[ 3.574662] ubi0: scanning is finished
[ 3.584140] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 3.584160] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.588508] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.595361] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.602135] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 3.608969] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 3.615217] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1635066095
[ 3.622190] ubi0: available PEBs: 748, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20
[ 3.631575] hctosys: unable to open rtc device¦[ 3.646202] /dev/root: Can't open blockdev
[ 3.646221] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 3.649180] Please append a correct "root=" boot option; here are the available partitions:
[ 3.656815] 1f00 12800 mtdblock0
[ 3.656817] (driver?)
[ 3.669055] 1f01 5120 mtdblock1
[ 3.669058] (driver?)
[ 3.675637] 1f02 512 mtdblock2
[ 3.675639] (driver?)
[ 3.682075] 1f03 1280 mtdblock3
[ 3.682077] (driver?)
[ 3.688586] 1f04 1280 mtdblock4
[ 3.688588] (driver?)
[ 3.695163] 1f05 4096 mtdblock5
[ 3.695166] (driver?)
[ 3.701606] 1f06 98816 mtdblock6
[ 3.701608] (driver?)
[ 3.708117] 1f07 7168 mtdblock7
[ 3.708120] (driver?)
[ 3.714686] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.717078] CPU1: stopping
[ 3.725319] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.154 #0
[ 3.728004] Hardware name: Generic DT based system
[ 3.734178] Function entered at [<c030f874>] from [<c030b870>]
[ 3.738772] Function entered at [<c030b870>] from [<c0901b98>]
[ 3.744587] Function entered at [<c0901b98>] from [<c030eaa0>]
[ 3.750401] Function entered at [<c030eaa0>] from [<c05dd844>]
[ 3.756219] Function entered at [<c05dd844>] from [<c0301a8c>]
[ 3.762034] Exception stack(0xdd46bf18 to 0xdd46bf60)
[ 3.767857] bf00: 00000000 00000000
[ 3.773002] bf20: 1ce5f000 dd9a0a80 dcc45800 00000000 dd99fe30 00000000 00000000 00000000
[ 3.781164] bf40: dd8defe0 dd692980 00000015 dd46bf68 c0732088 c073208c 80000013 ffffffff
[ 3.789297] Function entered at [<c0301a8c>] from [<c073208c>]
[ 3.797452] Function entered at [<c073208c>] from [<c07324d4>]
[ 3.803179] Function entered at [<c07324d4>] from [<c034acfc>]
[ 3.808997] Function entered at [<c034acfc>] from [<c034b00c>]
[ 3.814810] Function entered at [<c034b00c>] from [<423024cc>]
[ 3.820632] Rebooting in 1 seconds..
What am I missing here? Maybe the uboot command I launch is wrong?
usbboot dev 0