QCA9558 failed init WLAN

kmxzq · December 17, 2020, 9:46am

Hi, i'm using device with chip QCA9558 as wlan 2.4G and eth, QCA9880 as wlan 5G, it works fine with official Firmware, but when i flash it with openwrt(LEDE) V17.01.4(linux kernel 4.4.194), driver ath9k&ath10k(backports-4.19.137-1), 5G works OK, but 2.4G failed to init.
Then i try to debug driver ath9k,find device hangs&reboot on ath/ath9k/hw.c in function (int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan,struct ath9k_hw_cal_data *caldata, bool fastcc))

if (!ath9k_hw_init_cal(ah, chan))
             return -EIO;

and /sys/kernel/debug/ieee80211/phy1/ath9k will find file "eeprom" can't be read in cat, device will reboot again.
some kernel debug info as below

Thu Dec 17 17:42:00 2020 kern.debug kernel: [20092.364446] ath: phy1: TX streams 1, RX streams: 1
Thu Dec 17 17:42:00 2020 kern.debug kernel: [20092.375008] ath: phy1: FULL-SLEEP -> AWAKE
Thu Dec 17 17:42:00 2020 kern.debug kernel: [20092.377667] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:00 2020 kern.debug kernel: [20092.380424] ath: phy1: ah->misc_mode 0x10000004
Thu Dec 17 17:42:00 2020 kern.debug kernel: [20092.477142] ath: phy1: AWAKE -> FULL-SLEEP
Thu Dec 17 17:42:00 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.563565] ath: phy1: Starting driver with initial channel: 2452 MHz
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.563587] ath: phy1: FULL-SLEEP -> AWAKE
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.566236] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.569016] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.576234] ath: phy1: ch=0 f=2452 low=2437 9 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.576253] ath: phy1: ch=1 f=2452 low=2437 13 h=2462 13 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.576270] ath: phy1: ch=2 f=2452 low=2437 10 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.576294] ath: phy1: for frequency=2452, calibration correction = 10 13 10
Thu Dec 17 17:42:01 2020 kern.warn kernel: [20092.576383] In init_queues in hw.c
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579860] ath: phy1: Reset TX queue: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579884] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579897] ath: phy1: Reset TX queue: 1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579915] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579926] ath: phy1: Reset TX queue: 2
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579940] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579953] ath: phy1: Reset TX queue: 3
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579968] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579980] ath: phy1: Reset TXQ, inactive queue: 4
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.579991] ath: phy1: Reset TXQ, inactive queue: 5
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580002] ath: phy1: Reset TXQ, inactive queue: 6
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580013] ath: phy1: Reset TX queue: 7
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580031] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580043] ath: phy1: Reset TX queue: 8
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580065] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580076] ath: phy1: Reset TX queue: 9
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580096] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580114] ath: phy1: ver 1024.0 opmode 2 chan 2452 Mhz
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20092.580133] ath: phy1: ah->misc_mode 0x10000004
Thu Dec 17 17:42:01 2020 kern.err kernel: [20092.580544] ath: phy1: Begin init_cal by xiang
Thu Dec 17 17:42:01 2020 kern.err kernel: [20092.585051] 9550 in calib
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.051246] ERROR in CALIB
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.053993] ath: phy1: Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x50d5a
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054010] ath: phy1: Enabled BB Watchdog timeout (25 ms)
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054031] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054044] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054056] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054068] ath: phy1: Do not enable IER ref count -1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054079] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054090] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054107] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054263] ath: phy1: Enable MIB counters
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054284] ath: phy1: Restore history: opmode 2 chan 2452 Mhz is_scanning=0 ofdm:3 cck:2
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054299] ath: phy1: **** ofdmlevel 3=>3, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054315] ath: phy1: **** ccklevel 2=>2, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054333] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054344] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054355] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054375] ath: phy1: New interrupt mask 0xf0000443
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054386] ath: phy1: new IMR 0x81800145
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054397] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.054412] ath: phy1: AR_IMR 0x81800145 IER 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055408] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055427] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055440] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055453] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055492] ath: phy1: Attach a VIF of type: 3
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055505] ath: phy1: Added interface at beacon slot: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055523] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055535] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055547] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055558] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055571] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055582] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055593] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055606] ath: phy1: ah->misc_mode 0x1000000c
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055629] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055676] ath: phy1: ch=0 f=2452 low=2437 9 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055694] ath: phy1: ch=1 f=2452 low=2437 13 h=2462 13 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055712] ath: phy1: ch=2 f=2452 low=2437 10 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055735] ath: phy1: for frequency=2452, calibration correction = 10 13 10
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055757] ath: phy1: Set HW RX filter: 0x104097
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055784] ath: phy1: Configure tx [queue/halq] [0/3], aifs: 2, cw_min: 3, cw_max: 7, txop: 47
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055812] ath: phy1: Set queue properties for: 3
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055824] ath: phy1: Reset TX queue: 3
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055846] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055864] ath: phy1: Configure tx [queue/halq] [1/2], aifs: 2, cw_min: 7, cw_max: 15, txop: 94
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055890] ath: phy1: Set queue properties for: 2
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055900] ath: phy1: Reset TX queue: 2
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055915] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055932] ath: phy1: Configure tx [queue/halq] [2/1], aifs: 3, cw_min: 15, cw_max: 1023, txop: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055958] ath: phy1: Set queue properties for: 1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055968] ath: phy1: Reset TX queue: 1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055982] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.055999] ath: phy1: Configure tx [queue/halq] [3/0], aifs: 7, cw_min: 15, cw_max: 1023, txop: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056025] ath: phy1: Set queue properties for: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056036] ath: phy1: Reset TX queue: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056050] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056070] ath: phy1: Monitor mode is disabled
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056083] ath: phy1: Set channel: 2452 MHz width: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056101] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056121] ath: phy1: Stopping ANI
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056131] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056142] ath: phy1: Disable MIB counters
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056216] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056229] ath: phy1: NF did not complete in calibration window
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.056269] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.063401] ath: phy1: ch=0 f=2452 low=2437 9 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.063422] ath: phy1: ch=1 f=2452 low=2437 13 h=2462 13 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.063439] ath: phy1: ch=2 f=2452 low=2437 10 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.063461] ath: phy1: for frequency=2452, calibration correction = 10 13 10
Thu Dec 17 17:42:01 2020 kern.warn kernel: [20093.063550] In init_queues in hw.c
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067006] ath: phy1: Reset TX queue: 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067044] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067057] ath: phy1: Reset TX queue: 1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067076] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067087] ath: phy1: Reset TX queue: 2
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067101] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067113] ath: phy1: Reset TX queue: 3
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067128] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067141] ath: phy1: Reset TXQ, inactive queue: 4
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067151] ath: phy1: Reset TXQ, inactive queue: 5
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067162] ath: phy1: Reset TXQ, inactive queue: 6
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067173] ath: phy1: Reset TX queue: 7
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067192] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067203] ath: phy1: Reset TX queue: 8
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067225] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067237] ath: phy1: Reset TX queue: 9
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067257] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067276] ath: phy1: ver 1024.0 opmode 3 chan 2452 Mhz
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.067294] ath: phy1: ah->misc_mode 0x1000000c
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.067706] ath: phy1: Begin init_cal by xiang
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.072218] 9550 in calib
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.537619] ERROR in CALIB
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.540368] ath: phy1: Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x50d5a
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.540386] ath: phy1: Enabled BB Watchdog timeout (25 ms)
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.540402] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 0 return 0
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.546842] ath: phy1: Begin complete reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551103] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551117] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551129] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551142] ath: phy1: Do not enable IER ref count -1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551153] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551164] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551180] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551335] ath: phy1: Enable MIB counters
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551355] ath: phy1: **** ofdmlevel 3=>3, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551370] ath: phy1: **** ccklevel 2=>2, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551390] ath: phy1: Starting ANI
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551405] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551416] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551427] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.551440] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:01 2020 kern.err kernel: [20093.551454] ath: phy1: END complete reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555531] ath: phy1: New interrupt mask 0xf0000443
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555542] ath: phy1: new IMR 0x81800145
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555554] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555601] ath: phy1: ch=0 f=2452 low=2437 9 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555620] ath: phy1: ch=1 f=2452 low=2437 13 h=2462 13 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555637] ath: phy1: ch=2 f=2452 low=2437 10 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.555659] ath: phy1: for frequency=2452, calibration correction = 10 13 10
Thu Dec 17 17:42:01 2020 kern.info kernel: [20093.555810] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Thu Dec 17 17:42:01 2020 kern.warn kernel: [20093.567962] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.575762] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.575781] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.575794] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.575807] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.575939] ath: phy1: Set HW RX filter: 0x104097
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.667077] ath: phy1: New interrupt mask 0xf0000443
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.667098] ath: phy1: new IMR 0x81800145
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.667111] ath: phy1: disable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.667126] ath: phy1: AWAKE -> FULL-SLEEP
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.667203] ath: phy1: FULL-SLEEP -> AWAKE
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.669854] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.672565] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.672577] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.672590] ath: phy1: enable IER
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.672604] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.767069] ath: phy1: AWAKE -> FULL-SLEEP
Thu Dec 17 17:42:01 2020 kern.info kernel: [20093.775487] device wlan1 entered promiscuous mode
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.780485] ath: phy1: FULL-SLEEP -> AWAKE
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.783140] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:01 2020 kern.debug kernel: [20093.785854] ath: phy1: Set HW RX filter: 0x104097
Thu Dec 17 17:42:01 2020 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Dec 17 17:42:01 2020 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792604] ath: phy1: Set channel: 2452 MHz width: 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792635] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792659] ath: phy1: Stopping ANI
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792670] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792684] ath: phy1: Disable MIB counters
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792783] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.792827] ath: phy1: reset MAC via external reset
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.800090] ath: phy1: ch=0 f=2452 low=2437 9 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.800112] ath: phy1: ch=1 f=2452 low=2437 13 h=2462 13 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.800129] ath: phy1: ch=2 f=2452 low=2437 10 h=2462 10 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.800152] ath: phy1: for frequency=2452, calibration correction = 10 13 10
Thu Dec 17 17:42:02 2020 kern.warn kernel: [20093.800241] In init_queues in hw.c
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803689] ath: phy1: Reset TX queue: 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803711] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803722] ath: phy1: Reset TX queue: 1
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803740] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803751] ath: phy1: Reset TX queue: 2
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803764] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803776] ath: phy1: Reset TX queue: 3
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803791] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803803] ath: phy1: Reset TXQ, inactive queue: 4
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803814] ath: phy1: Reset TXQ, inactive queue: 5
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803825] ath: phy1: Reset TXQ, inactive queue: 6
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803836] ath: phy1: Reset TX queue: 7
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803855] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803865] ath: phy1: Reset TX queue: 8
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803887] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803898] ath: phy1: Reset TX queue: 9
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803917] ath: phy1: tx ok 0x38f err 0x38f desc 0x0 eol 0x0 urn 0x0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803935] ath: phy1: ver 1024.0 opmode 3 chan 2452 Mhz
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20093.803954] ath: phy1: ah->misc_mode 0x1000000c
Thu Dec 17 17:42:02 2020 kern.err kernel: [20093.804365] ath: phy1: Begin init_cal by xiang
Thu Dec 17 17:42:02 2020 kern.err kernel: [20093.808896] 9550 in calib
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.272831] ERROR in CALIB
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.275582] ath: phy1: Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x50d5a
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.275599] ath: phy1: Enabled BB Watchdog timeout (25 ms)
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.275616] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 0 return 0
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.282069] ath: phy1: Begin complete reset
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286313] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286326] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286338] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286351] ath: phy1: Do not enable IER ref count -1
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286362] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286373] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286389] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286544] ath: phy1: Enable MIB counters
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286565] ath: phy1: **** ofdmlevel 3=>3, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286580] ath: phy1: **** ccklevel 2=>2, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286600] ath: phy1: Starting ANI
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286614] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286625] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286637] ath: phy1: enable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.286650] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.286664] ath: phy1: END complete reset
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.290778] ath: phy1: New interrupt mask 0xf0000443
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.290790] ath: phy1: new IMR 0x81800145
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.290802] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.291190] ath: phy1: Set HW RX filter: 0x104097
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294845] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294864] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294877] ath: phy1: enable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294890] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294947] ath: phy1: Set channel: 2412 MHz width: 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294966] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.294991] ath: phy1: Stopping ANI
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295001] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295013] ath: phy1: Disable MIB counters
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295089] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295102] ath: phy1: NF did not complete in calibration window
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295117] ath: phy1: FastChannelChange for 2452 -> 2412
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295182] ath: phy1: ch=0 f=2412 low=2412 10 h=2412 10 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295201] ath: phy1: ch=1 f=2412 low=2412 11 h=2412 11 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295218] ath: phy1: ch=2 f=2412 low=2412 9 h=2412 9 n=0 0 p=0 0
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.295242] ath: phy1: for frequency=2412, calibration correction = 10 11 9
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.295279] ath: phy1: !!!CHANNEL CHANGE!!!by xiang
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.300918] 9550 in calib
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.767991] ERROR in CALIB
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.770741] ath: phy1: Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x58d5a
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.770759] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1 return 0
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.777208] ath: phy1: Begin complete reset
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781455] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781467] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781479] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781492] ath: phy1: Do not enable IER ref count -1
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781503] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781514] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781530] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781688] ath: phy1: Enable MIB counters
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781707] ath: phy1: **** ofdmlevel 3=>3, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781723] ath: phy1: **** ccklevel 2=>2, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781740] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781751] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781762] ath: phy1: enable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.781775] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:02 2020 kern.err kernel: [20094.781788] ath: phy1: END complete reset
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.785880] ath: phy1: New interrupt mask 0xf0000443
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.785891] ath: phy1: new IMR 0x81800145
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.785903] ath: phy1: disable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.799264] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.799285] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.799298] ath: phy1: enable IER
Thu Dec 17 17:42:02 2020 kern.debug kernel: [20094.799311] ath: phy1: AR_IMR 0x81800175 IER 0x1
Thu Dec 17 17:42:02 2020 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ACS
Thu Dec 17 17:42:02 2020 daemon.notice hostapd: wlan1: ACS-STARTED
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.886967] ath: phy1: Set channel: 2417 MHz width: 0
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.886993] ath: phy1: disable IER
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887016] ath: phy1: Stopping ANI
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887026] ath: phy1: disable IER
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887039] ath: phy1: Disable MIB counters
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887115] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887127] ath: phy1: NF did not complete in calibration window
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887142] ath: phy1: FastChannelChange for 2412 -> 2417
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887209] ath: phy1: ch=0 f=2417 low=2412 10 h=2437 9 n=0 0 p=0 0
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887227] ath: phy1: ch=1 f=2417 low=2412 11 h=2437 13 n=0 0 p=0 0
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887245] ath: phy1: ch=2 f=2417 low=2412 9 h=2437 10 n=0 0 p=0 0
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20094.887268] ath: phy1: for frequency=2417, calibration correction = 10 11 9
Thu Dec 17 17:42:03 2020 kern.err kernel: [20094.887306] ath: phy1: !!!CHANNEL CHANGE!!!by xiang
Thu Dec 17 17:42:03 2020 kern.err kernel: [20094.892899] 9550 in calib
Thu Dec 17 17:42:03 2020 kern.err kernel: [20095.358368] ERROR in CALIB
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.361116] ath: phy1: Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x58d5a
Thu Dec 17 17:42:03 2020 kern.err kernel: [20095.361134] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1 return 0
Thu Dec 17 17:42:03 2020 kern.err kernel: [20095.367582] ath: phy1: Begin complete reset
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371829] ath: phy1: disable IER
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371842] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371854] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371867] ath: phy1: Do not enable IER ref count -1
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371878] ath: phy1: New interrupt mask 0xf0000473
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371889] ath: phy1: new IMR 0x81800175
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.371906] ath: phy1: macaddr: 14:3d:f2:ca:c8:14, bssid: 00:00:00:00:00:00, bssidmask: ff:ff:ff:ff:ff:ff
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.372062] ath: phy1: Enable MIB counters
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.372082] ath: phy1: **** ofdmlevel 3=>3, rssi=0[lo=7 hi=40]
Thu Dec 17 17:42:03 2020 kern.debug kernel: [20095.372097] ath: phy1: **** ccklevel 2=>2, rssi=0[lo=7 hi=40]

Hope find a way to solve it, thanks!

dwzhang2k23 · January 24, 2024, 3:58am

Hi Gents,

I got the similar issue on QCA9563 card here, are you able to solve the issue? if so, how did you resolve it?

Thanks,
Dave

psherman · January 24, 2024, 4:29am

@dwzhang2k23 - You've bumped a >3 year old thread discussing a long since obsolete version of OpenWrt (actually LEDE). Are you also using LEDE?

dwzhang2k23 · January 24, 2024, 4:54am

I am using 19.07, thx

psherman · January 24, 2024, 5:13am

This version is also long since EOL and unsupported. You should upgrade to a modern version of OpenWrt.

What is the device in question? Let's see the output of:

ubus call system board

dwzhang2k23 · January 24, 2024, 7:29am

here is the output:
ubus call system board
{
"kernel": "4.14.245",
"hostname": "",
"system": "Qualcomm Atheros QCA956X ver 1 rev 0",
"model": "Compex WPJ563",
"board_name": "wpj563",
"release": {
"distribution": "OpenWrt",
"version": "19.07-SNAPSHOT",
"revision": "r11371-9882a54",
"target": "ar71xx/generic",
"description": "OpenWrt 19.07-SNAPSHOT r11371-9882a54"
}
}

psherman · January 24, 2024, 7:33am

Your device is supported by the most recent openwrt version. Please upgrade so that you are on a supported version.

https://firmware-selector.openwrt.org/?version=23.05.2&target=ath79%2Fgeneric&id=compex_wpj563

Note: do not keep settings from your current configuration- they are not compatible. You’ll have a default configuration after the upgrade.

dwzhang2k23 · January 24, 2024, 8:01am

thx, however, I cannot use the default image because I have modified the flash partitions in my uboot and the reference clock to 40mhz. I will have to rebuild my own customized kernel.

fkl7834456 · January 24, 2024, 8:07am

I am not strong in programming, so I solve problems in simple and primitive ways and it always works.
We go to Luci, System - Autostart - Starting Packages and User Services When The Device Is Turned On.
add commands

sleep 10 && /etc/init.d/network restart
sleep 5 && /etc/init.d/firewall restart
Exit 0

And reboot the router