Hello, finally I installed an u-boot and openwrt firmware for my old NAS from this page : https://openwrt.org/toh/zyxel/nsa325. There was no problem during process. But after reset during loading kernel, process is interruped with above information.
What can I do?
U-Boot 2018.03 (Jun 27 2018 - 06:41:13 +0000)
ZyXEL NSA325 2-Bay Power Media Server
SoC: Kirkwood 88F6282_A1
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: 128 MiB
MMC:
Loading Environment from NAND... OK
In: serial
Out: serial
Err: serial
Net: egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 0
## Error: "setenv" not defined
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=2", size 126 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 1012, bad PEBs: 2, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1682627295
ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 18
Read 0 bytes from volume kernel to 800000
No size specified -> Using max size (2709504)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: ARM OpenWrt Linux-5.10.176
Created: 2023-04-27 20:28:15 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2689432 Bytes = 2.6 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Thu Apr 27 20:28:15 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: ZyXEL NSA325
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 510160K/524288K available (6008K kernel code, 600K rwdata, 928K rodata, 1024K init, 215K bss, 14128K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000036] Switching to timer-based delay loop, resolution 5ns
[ 0.000155] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000179] pid_max: default: 32768 minimum: 301
[ 0.000334] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000355] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001119] CPU: Testing write buffer coherency: ok
[ 0.002145] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002358] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.002556] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.005349] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005376] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.005491] pinctrl core: initialized pinctrl subsystem
[ 0.006828] NET: Registered protocol family 16
[ 0.007152] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.008017] thermal_sys: Registered thermal governor 'step_wise'
[ 0.008105] cpuidle: using governor ladder
[ 0.008364] Feroceon L2: Enabling L2
[ 0.008400] Feroceon L2: Cache support initialised.
[ 0.016251] No ATAGs?
[ 0.052546] SCSI subsystem initialized
[ 0.053746] usbcore: registered new interface driver usbfs
[ 0.053787] usbcore: registered new interface driver hub
[ 0.053824] usbcore: registered new device driver usb
[ 0.058151] clocksource: Switched to clocksource orion_clocksource
[ 0.058778] NET: Registered protocol family 2
[ 0.058952] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.059664] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.059707] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.059760] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.059810] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.059874] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.059897] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.060072] NET: Registered protocol family 1
[ 0.060099] PCI: CLS 0 bytes, default 32
[ 0.063582] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.066558] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.066575] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.067169] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.068974] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.069924] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 0.069958] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.069978] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.069991] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.070135] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 0.070151] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.070162] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.070171] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 0.070180] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.070269] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
[ 0.071244] PCI: bus0: Fast back to back transfers disabled
[ 0.071256] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.071366] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330
[ 0.071399] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 0.071520] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.071558] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.072404] PCI: bus1: Fast back to back transfers disabled
[ 0.072417] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.072558] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[ 0.072572] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[ 0.072590] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.072601] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 0.072649] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 0.072665] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 0.073327] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.074548] printk: console [ttyS0] disabled
[ 0.074622] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 0.672108] printk: console [ttyS0] enabled
[ 0.676810] Loading iSCSI transport class v2.0-870.
[ 0.685286] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[ 0.691694] nand: Eon NAND 128MiB 3,3V 8-bit
[ 0.695977] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.703595] Scanning device for bad blocks
[ 0.712509] Bad eraseblock 100 at 0x000000c80000
[ 0.721891] Bad eraseblock 200 at 0x000001900000
[ 0.765649] 3 fixed-partitions partitions found on MTD device orion_nand
[ 0.772389] Creating 3 MTD partitions on "orion_nand":
[ 0.777546] 0x000000000000-0x0000000c0000 : "uboot"
[ 0.784258] 0x0000000c0000-0x000000140000 : "uboot_env"
[ 0.789991] 0x000000140000-0x000008000000 : "ubi"
[ 0.805109] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 0.815068] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 5c:f4:ab:50:13:2c
[ 0.824038] i2c /dev entries driver
[ 0.828653] orion_wdt: Initial timeout 21 sec
[ 0.842145] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 0.850033] NET: Registered protocol family 10
[ 0.856184] Segment Routing with IPv6
[ 0.859955] NET: Registered protocol family 17
[ 0.864465] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.877618] 8021q: 802.1Q VLAN Support v1.8
[ 0.885564] UBI: auto-attach mtd2
[ 0.888933] ubi0: attaching mtd2
[ 1.062119] ubi0: scanning is finished
[ 1.076851] ubi0: attached mtd2 (name "ubi", size 126 MiB)
[ 1.082396] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.089316] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.096042] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.102860] ubi0: good PEBs: 1012, bad PEBs: 2, corrupted PEBs: 0
[ 1.108980] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.116230] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1682627295
[ 1.125410] ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 18
[ 1.135022] ubi0: background thread "ubi_bgt0d" started, PID 468
[ 1.141825] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.147333] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.159742] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.169858] Freeing unused kernel memory: 1024K
[ 1.174598] Run /sbin/init as init process
[ 1.197688] SQUASHFS error: xz decompression failed, data probably corrupt
[ 1.204621] SQUASHFS error: Failed to read block 0x1138ce: -5
[ 1.210397] SQUASHFS error: Unable to read fragment cache entry [1138ce]
[ 1.217127] SQUASHFS error: Unable to read page, block 1138ce, size 13d5c
[ 1.223950] SQUASHFS error: Unable to read fragment cache entry [1138ce]
[ 1.230685] SQUASHFS error: Unable to read page, block 1138ce, size 13d5c
[ 1.237500] SQUASHFS error: Unable to read fragment cache entry [1138ce]
[ 1.244236] SQUASHFS error: Unable to read page, block 1138ce, size 13d5c
[ 1.251057] SQUASHFS error: Unable to read fragment cache entry [1138ce]
[ 1.257780] SQUASHFS error: Unable to read page, block 1138ce, size 13d5c
[ 1.264603] SQUASHFS error: Unable to read fragment cache entry [1138ce]
[ 1.271342] SQUASHFS error: Unable to read page, block 1138ce, size 13d5c
[ 1.278223] Starting init: /sbin/init exists but couldn't execute it (error -5)
[ 1.285562] Run /etc/init as init process
[ 1.289754] Run /bin/init as init process
[ 1.295574] Run /bin/sh as init process
BusyBox v1.35.0 (2023-04-27 20:28:15 UTC) built-in shell (ash)
/bin/sh: can't access tty; job control turned off
/ #