Populating the OpenWRT One M.2 slot?

Installing and Using OpenWrt
1

Hi,
I have read a few post that implied (to me) that it was relatively straight forward to populate this slot. However, it has not been that way for me.
I am using an SK HyNix BC901 HFS256GEJ4X112N card.
With the card fitted, "The One" (is there a nickname forming yet?), will boot, and get the the command prompt as seen by a terminal on the front USB port. However, no connection via HTTP is possible and no DHCP available for the workstations.
Can anyone offer a Quick Start guide to setting up this memory as an NFS Share.

Regards, Martin

2

the boot log might include some useful information ...

3

Not that I can decipher...
Can I share it with you? Boot log with NVMe installed

Trying to kompare boot logs with & without the NVMe is not very practical as all the timings are different.

4 
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.6.73 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28427-6df0e3d02a) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Feb  3 23:09:37 2025
[    0.000000] Machine model: OpenWrt One
[    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[    0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000
[    0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000
[    0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff]
[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff]
[    0.000000]   node   0: [mem 0x0000000048000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.4
[    0.000000] percpu: Embedded 18 pages/cpu s35560 r8192 d29976 u73728
[    0.000000] pcpu-alloc: s35560 r8192 d29976 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: 
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[    0.000000] software IO TLB: area num 2.
[    0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[    0.000000] Memory: 1010800K/1048576K available (9024K kernel code, 998K rwdata, 1672K rodata, 448K init, 305K bss, 37776K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] Root IRQ handler: 0xffffffc080010080
[    0.000000] GICv3: GICv3 features: 16 PPIs
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[    0.000089] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000098] pid_max: default: 32768 minimum: 301
[    0.003057] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.003069] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.005327] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.005873] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[    0.006032] rcu: Hierarchical SRCU implementation.
[    0.006035] rcu: 	Max phase no-delay instances is 1000.
[    0.006481] smp: Bringing up secondary CPUs ...
[    0.006855] Detected VIPT I-cache on CPU1
[    0.006904] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[    0.006935] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.007008] smp: Brought up 1 node, 2 CPUs
[    0.007014] SMP: Total of 2 processors activated.
[    0.007018] CPU features: detected: 32-bit EL0 Support
[    0.007021] CPU features: detected: CRC32 instructions
[    0.007055] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.007059] CPU: All CPU(s) started at EL2
[    0.007060] alternatives: applying system-wide alternatives
[    0.011264] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.011285] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.012591] pinctrl core: initialized pinctrl subsystem
[    0.013694] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.014274] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.014303] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.014324] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.014746] thermal_sys: Registered thermal governor 'fair_share'
[    0.014750] thermal_sys: Registered thermal governor 'bang_bang'
[    0.014753] thermal_sys: Registered thermal governor 'step_wise'
[    0.014755] thermal_sys: Registered thermal governor 'user_space'
[    0.014800] ASID allocator initialised with 65536 entries
[    0.015736] pstore: Using crash dump compression: deflate
[    0.015743] pstore: Registered ramoops as persistent store backend
[    0.015745] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.017643] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[    0.025116] Modules: 29616 pages in range for non-PLT usage
[    0.025126] Modules: 521136 pages in range for PLT usage
[    0.026276] cryptd: max_cpu_qlen set to 1000
[    0.027526] SCSI subsystem initialized
[    0.027769] libata version 3.00 loaded.
[    0.029516] clocksource: Switched to clocksource arch_sys_counter
[    0.031893] NET: Registered PF_INET protocol family
[    0.032043] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.033809] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.033828] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.033837] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.033890] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.034091] TCP: Hash tables configured (established 8192 bind 8192)
[    0.034471] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[    0.034609] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.034632] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.034926] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.034955] PCI: CLS 0 bytes, default 64
[    0.036427] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.041392] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.041401] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.074567] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.076341] gpio-export gpio-export: 3 gpio(s) exported
[    0.077180] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[    0.077209] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[    0.077221] mtk-pcie-gen3 11280000.pcie:      MEM 0x0020000000..0x002fffffff -> 0x0020000000
[    0.087280] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.091184] printk: console [ttyS0] disabled
[    0.111583] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[    0.111628] printk: console [ttyS0] enabled
[    0.911676] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 73, base_baud = 2500000) is a ST16650V2
[    0.926573] loop: module loaded
[    0.932536] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    0.937618] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.944103] Creating 4 MTD partitions on "spi0.0":
[    0.948886] 0x000000000000-0x000000040000 : "bl2-nor"
[    0.954715] 0x000000040000-0x000000100000 : "factory"
[    0.960980] 0x000000100000-0x000000180000 : "fip-nor"
[    0.966486] 0x000000180000-0x000000e00000 : "recovery"
[    0.975712] spi-nand spi1.1: calibration result: 0x3
[    0.980814] spi-nand spi1.1: Winbond SPI NAND was found.
[    0.986117] spi-nand spi1.1: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    0.994676] 2 fixed-partitions partitions found on MTD device spi1.1
[    1.001345] Creating 2 MTD partitions on "spi1.1":
[    1.006155] 0x000000000000-0x000000100000 : "bl2"
[    1.011994] 0x000000100000-0x000010000000 : "ubi"
[    1.174181] ubi0: default fastmap pool size: 100
[    1.178803] ubi0: default fastmap WL pool size: 50
[    1.183604] ubi0: attaching mtd5
[    2.379527] random: crng init done
[    2.881061] ubi0: scanning is finished
[    2.896624] ubi0: attached mtd5 (name "ubi", size 255 MiB)
[    2.902149] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.909015] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.915796] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.922748] ubi0: good PEBs: 2040, bad PEBs: 0, corrupted PEBs: 0
[    2.928828] ubi0: user volume: 6, internal volumes: 1, max. volumes count: 128
[    2.936038] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1733226068
[    2.945159] ubi0: available PEBs: 0, total reserved PEBs: 2040, PEBs reserved for bad PEB handling: 40
[    2.954461] ubi0: background thread "ubi_bgt0d" started, PID 295
[    2.955427] block ubiblock0_4: created from ubi0:4(fit)
[    3.172563] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081800000, irq 78
[    3.182474] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc081800000, irq 78
[    3.192301] i2c_dev: i2c /dev entries driver
[    3.199406] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[    3.208560] NET: Registered PF_INET6 protocol family
[    3.214405] Segment Routing with IPv6
[    3.218085] In-situ OAM (IOAM) with IPv6
[    3.222069] NET: Registered PF_PACKET protocol family
[    3.227135] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.240395] 8021q: 802.1Q VLAN Support v1.8
[    3.268761] phy phy-soc:usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[    3.276371] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[    3.283724] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[    3.290000] mtk-pcie-gen3 11280000.pcie:      MEM 0x0020000000..0x002fffffff -> 0x0020000000
[    3.546031] mtk-pcie-gen3 11280000.pcie: set MEM trans window[0]: cpu_addr = 0x20000000, pci_addr = 0x20000000, size = 0x10000000
[    3.558063] mtk-pcie-gen3 11280000.pcie: PCI host bridge to bus 0000:00
[    3.564704] pci_bus 0000:00: root bus resource [bus 00-ff]
[    3.570190] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    3.577053] pci_bus 0000:00: scanning bus
[    3.581083] pci 0000:00:00.0: [14c3:1f32] type 01 class 0x060400
[    3.587090] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[    3.593935] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[    3.600025] pci 0000:00:00.0: PME# disabled
[    3.605406] pci_bus 0000:00: fixups for bus
[    3.609615] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[    3.616306] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    3.624310] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[    3.631103] pci_bus 0000:01: scanning bus
[    3.635155] pci 0000:01:00.0: [1c5c:1d59] type 00 class 0x010802
[    3.641192] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    3.648245] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 63.012 Gb/s with 16.0 GT/s PCIe x4 link)
[    3.689571] pci_bus 0000:01: fixups for bus
[    3.693756] pci_bus 0000:01: bus scan returning with max=01
[    3.699316] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    3.705936] pci_bus 0000:00: bus scan returning with max=01
[    3.711536] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    3.718313] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x20107fff 64bit]
[    3.725624] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x20003fff 64bit]
[    3.732938] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.737893] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    3.744678] pci_bus 0000:00: resource 4 [mem 0x20000000-0x2fffffff]
[    3.750942] pci_bus 0000:01: resource 1 [mem 0x20000000-0x200fffff]
[    3.757356] pcieport 0000:00:00.0: assign IRQ: got 84
[    3.762414] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[    3.768504] pcieport 0000:00:00.0: enabling bus mastering
[    3.774546] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[    3.782990] mtk-pcie-gen3 11280000.pcie: msi#0x1 address_hi 0x0 address_lo 0x11280c00 data 1
[    3.791421] mtk-pcie-gen3 11280000.pcie: msi#0x2 address_hi 0x0 address_lo 0x11280c00 data 2
[    3.799852] mtk-pcie-gen3 11280000.pcie: msi#0x3 address_hi 0x0 address_lo 0x11280c00 data 3
[    3.808277] mtk-pcie-gen3 11280000.pcie: msi#0x4 address_hi 0x0 address_lo 0x11280c00 data 4
[    3.816714] mtk-pcie-gen3 11280000.pcie: msi#0x5 address_hi 0x0 address_lo 0x11280c00 data 5
[    3.825143] mtk-pcie-gen3 11280000.pcie: msi#0x6 address_hi 0x0 address_lo 0x11280c00 data 6
[    3.833573] mtk-pcie-gen3 11280000.pcie: msi#0x7 address_hi 0x0 address_lo 0x11280c00 data 7
[    3.842003] mtk-pcie-gen3 11280000.pcie: msi#0x8 address_hi 0x0 address_lo 0x11280c00 data 8
[    3.850433] mtk-pcie-gen3 11280000.pcie: msi#0x9 address_hi 0x0 address_lo 0x11280c00 data 9
[    3.858858] mtk-pcie-gen3 11280000.pcie: msi#0xa address_hi 0x0 address_lo 0x11280c00 data 10
[    3.867374] mtk-pcie-gen3 11280000.pcie: msi#0xb address_hi 0x0 address_lo 0x11280c00 data 11
[    3.875894] mtk-pcie-gen3 11280000.pcie: msi#0xc address_hi 0x0 address_lo 0x11280c00 data 12
[    3.884411] mtk-pcie-gen3 11280000.pcie: msi#0xd address_hi 0x0 address_lo 0x11280c00 data 13
[    3.892928] mtk-pcie-gen3 11280000.pcie: msi#0xe address_hi 0x0 address_lo 0x11280c00 data 14
[    3.901444] mtk-pcie-gen3 11280000.pcie: msi#0xf address_hi 0x0 address_lo 0x11280c00 data 15
[    3.909960] mtk-pcie-gen3 11280000.pcie: msi#0x10 address_hi 0x0 address_lo 0x11280c00 data 16
[    3.918558] mtk-pcie-gen3 11280000.pcie: msi#0x11 address_hi 0x0 address_lo 0x11280c00 data 17
[    3.927161] mtk-pcie-gen3 11280000.pcie: msi#0x12 address_hi 0x0 address_lo 0x11280c00 data 18
[    3.935766] mtk-pcie-gen3 11280000.pcie: msi#0x13 address_hi 0x0 address_lo 0x11280c00 data 19
[    3.944370] mtk-pcie-gen3 11280000.pcie: msi#0x14 address_hi 0x0 address_lo 0x11280c00 data 20
[    3.952973] mtk-pcie-gen3 11280000.pcie: msi#0x15 address_hi 0x0 address_lo 0x11280c00 data 21
[    3.961576] mtk-pcie-gen3 11280000.pcie: msi#0x16 address_hi 0x0 address_lo 0x11280c00 data 22
[    3.970179] mtk-pcie-gen3 11280000.pcie: msi#0x17 address_hi 0x0 address_lo 0x11280c00 data 23
[    3.978777] mtk-pcie-gen3 11280000.pcie: msi#0x18 address_hi 0x0 address_lo 0x11280c00 data 24
[    3.987380] mtk-pcie-gen3 11280000.pcie: msi#0x19 address_hi 0x0 address_lo 0x11280c00 data 25
[    3.995986] mtk-pcie-gen3 11280000.pcie: msi#0x1a address_hi 0x0 address_lo 0x11280c00 data 26
[    4.004590] mtk-pcie-gen3 11280000.pcie: msi#0x1b address_hi 0x0 address_lo 0x11280c00 data 27
[    4.013194] mtk-pcie-gen3 11280000.pcie: msi#0x1c address_hi 0x0 address_lo 0x11280c00 data 28
[    4.021797] mtk-pcie-gen3 11280000.pcie: msi#0x1d address_hi 0x0 address_lo 0x11280c00 data 29
[    4.030401] mtk-pcie-gen3 11280000.pcie: msi#0x1e address_hi 0x0 address_lo 0x11280c00 data 30
[    4.038999] mtk-pcie-gen3 11280000.pcie: msi#0x1f address_hi 0x0 address_lo 0x11280c00 data 31
[    4.048381] mtk-pcie-gen3 11280000.pcie: msi#0x0 address_hi 0x0 address_lo 0x11280c00 data 0
[    4.056991] pcieport 0000:00:00.0: PME: Signaling with IRQ 85
[    4.063086] pcieport 0000:00:00.0: AER: enabled with IRQ 85
[    4.068780] pcieport 0000:00:00.0: save config 0x00: 0x1f3214c3
[    4.074724] pcieport 0000:00:00.0: save config 0x04: 0x00100406
[    4.080648] pcieport 0000:00:00.0: save config 0x08: 0x06040001
[    4.086557] pcieport 0000:00:00.0: save config 0x0c: 0x00010000
[    4.092478] pcieport 0000:00:00.0: save config 0x10: 0x20100004
[    4.098387] pcieport 0000:00:00.0: save config 0x14: 0x00000000
[    4.104301] pcieport 0000:00:00.0: save config 0x18: 0x00010100
[    4.110213] pcieport 0000:00:00.0: save config 0x1c: 0x000001f1
[    4.116120] pcieport 0000:00:00.0: save config 0x20: 0x20002000
[    4.122033] pcieport 0000:00:00.0: save config 0x24: 0x0001fff1
[    4.127940] pcieport 0000:00:00.0: save config 0x28: 0x00000000
[    4.133853] pcieport 0000:00:00.0: save config 0x2c: 0x00000000
[    4.139770] pcieport 0000:00:00.0: save config 0x30: 0x00000000
[    4.145678] pcieport 0000:00:00.0: save config 0x34: 0x00000080
[    4.151591] pcieport 0000:00:00.0: save config 0x38: 0x00000000
[    4.157497] pcieport 0000:00:00.0: save config 0x3c: 0x00020154
[    4.165012] FIT: Detected U-Boot 2024.10-OpenWrt-r28161-ea17e958b9
[    4.171233] FIT: Selected configuration: "config-1" (OpenWrt openwrt_one)
[    4.178022] FIT:           kernel sub-image 0x00001000..0x00560599 "kernel-1" (ARM64 OpenWrt Linux-6.6.73) 
[    4.187779] FIT:          flat_dt sub-image 0x00561000..0x005684a3 "fdt-1" (ARM64 OpenWrt openwrt_one device tree blob) 
[    4.198655] FIT:       filesystem sub-image 0x00569000..0x00a20fff "rootfs-1" (ARM64 OpenWrt openwrt_one rootfs) 
[    4.209449] block ubiblock0_4: mapped 1 uImage.FIT filesystem sub-image as /dev/fit0
[    4.218116] clk: Disabling unused clocks
[    4.228145] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[    4.235508] Freeing unused kernel memory: 448K
[    4.240073] Run /sbin/init as init process
[    4.244160]   with arguments:
[    4.247114]     /sbin/init
[    4.249833]   with environment:
[    4.252962]     HOME=/
[    4.255310]     TERM=linux
[    4.492700] init: Console is alive
[    4.496270] init: - watchdog -
[    5.050073] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.308312] Airoha EN8811H mdio-bus:0f: MD32 firmware version: 24082302
[    7.326286] usbcore: registered new interface driver usbfs
[    7.331862] usbcore: registered new interface driver hub
[    7.337215] usbcore: registered new device driver usb
[    7.342996] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    7.355195] nvme 0000:01:00.0: assign IRQ: got 84
[    7.360145] nvme nvme0: pci function 0000:01:00.0
[    7.364881] nvme 0000:01:00.0: enabling device (0000 -> 0002)
[    7.370671] nvme 0000:01:00.0: enabling bus mastering
[    7.375824] mtk-pcie-gen3 11280000.pcie: msi#0x1 address_hi 0x0 address_lo 0x11280c00 data 1
[    7.384301] nvme 0000:01:00.0: save config 0x00: 0x1d591c5c
[    7.389871] nvme 0000:01:00.0: save config 0x04: 0x00100406
[    7.395433] nvme 0000:01:00.0: save config 0x08: 0x01080203
[    7.401001] nvme 0000:01:00.0: save config 0x0c: 0x00000000
[    7.406562] nvme 0000:01:00.0: save config 0x10: 0x20000004
[    7.412128] nvme 0000:01:00.0: save config 0x14: 0x00000000
[    7.417690] nvme 0000:01:00.0: save config 0x18: 0x00000000
[    7.423264] nvme 0000:01:00.0: save config 0x1c: 0x00000000
[    7.428825] nvme 0000:01:00.0: save config 0x20: 0x00000000
[    7.434392] nvme 0000:01:00.0: save config 0x24: 0x00000000
[    7.439958] nvme 0000:01:00.0: save config 0x28: 0x00000000
[    7.445519] nvme 0000:01:00.0: save config 0x2c: 0x1d591c5c
[    7.451086] nvme 0000:01:00.0: save config 0x30: 0x00000000
[    7.456647] nvme 0000:01:00.0: save config 0x34: 0x00000040
[    7.462213] nvme 0000:01:00.0: save config 0x38: 0x00000000
[    7.467774] nvme 0000:01:00.0: save config 0x3c: 0x00000154
[    7.489318] hwmon hwmon1: temp1_input not attached to any thermal zone
[    7.495970] hwmon hwmon1: temp2_input not attached to any thermal zone
[    7.502543] hwmon hwmon1: temp3_input not attached to any thermal zone
[    7.513671] nvme nvme0: allocated 64 MiB host memory buffer.
[    7.526568] mtk-pcie-gen3 11280000.pcie: msi#0x1 address_hi 0x0 address_lo 0x11280c00 data 1
[    7.535083] mtk-pcie-gen3 11280000.pcie: msi#0x2 address_hi 0x0 address_lo 0x11280c00 data 2
[    7.543546] mtk-pcie-gen3 11280000.pcie: msi#0x3 address_hi 0x0 address_lo 0x11280c00 data 3
[    7.555293] nvme nvme0: 2/0/0 default/read/poll queues
[    7.571282]  nvme0n1: p1
[    7.578835] xhci-mtk 11200000.usb: xHCI Host Controller
[    7.584108] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[    7.591614] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000200010
[    7.600782] xhci-mtk 11200000.usb: irq 89, io mem 0x11200000
[    7.606538] xhci-mtk 11200000.usb: xHCI Host Controller
[    7.611765] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[    7.619153] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[    7.626675] hub 1-0:1.0: USB hub found
[    7.630537] hub 1-0:1.0: 1 port detected
[    7.635005] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.643607] hub 2-0:1.0: USB hub found
[    7.647404] hub 2-0:1.0: 1 port detected
[    7.655999] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.673038] init: - preinit -
[    8.092074] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:0f] driver [Airoha EN8811H] (irq=53)
[    8.104955] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   12.702124] UBIFS (ubi0:5): Mounting in unauthenticated mode
[   12.707898] UBIFS (ubi0:5): background thread "ubifs_bgt0_5" started, PID 859
[   12.766334] UBIFS (ubi0:5): recovery needed
[   13.058912] UBIFS (ubi0:5): recovery completed
[   13.063442] UBIFS (ubi0:5): UBIFS: mounted UBI device 0, volume 5, name "rootfs_data"
[   13.071269] UBIFS (ubi0:5): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   13.081180] UBIFS (ubi0:5): FS size: 228556800 bytes (217 MiB, 1800 LEBs), max 1812 LEBs, journal size 11427840 bytes (10 MiB, 90 LEBs)
[   13.093341] UBIFS (ubi0:5): reserved for root: 4952683 bytes (4836 KiB)
[   13.099947] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID B85A4275-D809-4265-B3B9-EB31FB28F272, small LPT model
[   13.118933] mount_root: loading kmods from internal overlay
[   13.272534] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   13.302164] Key type encrypted registered
[   13.363408] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[   13.406011] usbcore: registered new interface driver usb-storage
[   13.412364] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   15.496907] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[   15.511221] block: extroot: not configured
[   15.519228] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   15.526627] block: extroot: not configured
[   15.533582] mount_root: switching to ubifs overlay
[   15.546270] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[   15.562886] urandom-seed: Seeding with /etc/urandom.seed
[   15.624390] procd: - early -
[   15.627340] procd: - watchdog -
[   16.212813] procd: - watchdog -
[   16.222430] procd: - ubus -
[   16.376999] procd: - init -
Please press Enter to activate this console.
[   16.963849] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.017895] NET: Registered PF_ALG protocol family
[   17.030976] Key type dns_resolver registered
[   17.143622] urngd: v1.0.2 started.
[   17.327870] RPC: Registered named UNIX socket transport module.
[   17.333819] RPC: Registered udp transport module.
[   17.338513] RPC: Registered tcp transport module.
[   17.343226] RPC: Registered tcp-with-tls transport module.
[   17.348701] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   17.744935] NFS: Registering the id_resolver key type
[   17.750043] Key type id_resolver registered
[   17.754225] Key type id_legacy registered
[   17.761800] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[   17.780059] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[   17.787547] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[   17.802639] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
[   17.810203] rtc-pcf8563 0-0051: registered as rtc0
[   17.816206] rtc-pcf8563 0-0051: low voltage detected, date/time is not reliable.
[   17.823643] rtc-pcf8563 0-0051: hctosys: unable to read the hardware clock
[   18.074823] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[   18.162789] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823161240a
[   18.162789] 
[   18.430700] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823161304
[   18.552031] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823161841
[   18.649951] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[   18.701952] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[   18.758735] PPP generic driver version 2.4.2
[   18.764220] NET: Registered PF_PPPOX protocol family
[   18.772719] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.502939] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[   23.623841] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:0f] driver [Airoha EN8811H] (irq=53)
[   23.642261] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
[   23.652272] br-lan: port 1(eth0) entered blocking state
[   23.657514] br-lan: port 1(eth0) entered disabled state
[   23.662849] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[   23.669894] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[   23.711479] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[   23.721125] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[   24.976806] br-lan: port 2(phy0-ap0) entered blocking state
[   24.982514] br-lan: port 2(phy0-ap0) entered disabled state
[   24.988146] mt798x-wmac 18000000.wifi phy0-ap0: entered allmulticast mode
[   24.995239] mt798x-wmac 18000000.wifi phy0-ap0: entered promiscuous mode
[   25.002175] br-lan: port 2(phy0-ap0) entered blocking state
[   25.007758] br-lan: port 2(phy0-ap0) entered forwarding state
[   25.201861] br-lan: port 3(phy1-ap0) entered blocking state
[   25.207450] br-lan: port 3(phy1-ap0) entered disabled state
[   25.213167] mt798x-wmac 18000000.wifi phy1-ap0: entered allmulticast mode
[   25.220243] mt798x-wmac 18000000.wifi phy1-ap0: entered promiscuous mode
[   25.227101] br-lan: port 3(phy1-ap0) entered blocking state
[   25.232732] br-lan: port 3(phy1-ap0) entered forwarding state
[   25.688215] br-lan: port 2(phy0-ap0) entered disabled state
[   26.722625] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   26.730548] NFSD: Using legacy client tracking operations.
[   26.736038] NFSD: starting 10-second grace period (net f0000000)
[   27.930079] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   32.952491] br-lan: port 2(phy0-ap0) entered blocking state
[   32.958079] br-lan: port 2(phy0-ap0) entered forwarding state
[   34.154202] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[   34.154807] br-lan: port 1(eth0) entered blocking state
[   34.167868] br-lan: port 1(eth0) entered forwarding state
5

ok,

post the output of ps, service and netstat -tl.

6

Here is ps ...

root@OpenWrt-One:~# ps
  PID USER       VSZ STAT COMMAND
    1 root      2332 S    /sbin/procd
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [pool_workqueue_]
    4 root         0 IW<  [kworker/R-rcu_g]
    5 root         0 IW<  [kworker/R-rcu_p]
    6 root         0 IW<  [kworker/R-slub_]
    7 root         0 IW<  [kworker/R-netns]
    8 root         0 IW   [kworker/0:0-mm_]
    9 root         0 IW<  [kworker/0:0H-ev]
   10 root         0 IW   [kworker/0:1-dev]
   11 root         0 IW   [kworker/u4:0-ev]
   12 root         0 IW<  [kworker/R-mm_pe]
   13 root         0 IW   [rcu_tasks_trace]
   14 root         0 SW   [ksoftirqd/0]
   15 root         0 IW   [rcu_sched]
   16 root         0 SW   [migration/0]
   17 root         0 SW   [cpuhp/0]
   18 root         0 SW   [cpuhp/1]
   19 root         0 SW   [migration/1]
   20 root         0 SW   [ksoftirqd/1]
   21 root         0 IW   [kworker/1:0-dev]
   22 root         0 IW<  [kworker/1:0H-ev]
   23 root         0 IW<  [kworker/R-inet_]
   24 root         0 IW   [kworker/u4:1-ev]
   25 root         0 IW   [kworker/0:2-pm]
   26 root         0 SW   [oom_reaper]
   27 root         0 IW<  [kworker/R-write]
   28 root         0 SW   [kcompactd0]
   29 root         0 IW<  [kworker/R-pencr]
   30 root         0 IW<  [kworker/R-pdecr]
   31 root         0 IW<  [kworker/R-crypt]
   32 root         0 IW<  [kworker/R-kbloc]
   33 root         0 IW<  [kworker/R-blkcg]
   34 root         0 IW<  [kworker/R-ata_s]
   35 root         0 IW   [kworker/u4:2-ev]
   36 root         0 SW   [watchdogd]
   37 root         0 IW<  [kworker/0:1H-kb]
   45 root         0 SW   [kswapd0]
   47 root         0 IW<  [kworker/R-kthro]
   73 root         0 IW   [kworker/1:1-dev]
  213 root         0 IW   [kworker/1:2-dev]
  214 root         0 IW   [kworker/1:3-rcu]
  217 root         0 IW   [kworker/1:4-eve]
  220 root         0 IW   [kworker/1:5-eve]
  221 root         0 IW   [kworker/1:6-rcu]
  224 root         0 IW   [kworker/1:7-dev]
  250 root         0 SW   [spi0]
  281 root         0 SW   [spi1]
  282 root         0 IW   [kworker/0:3-rcu]
  284 root         0 IW   [kworker/0:4-eve]
  297 root         0 SW   [ubi_bgt0d]
  313 root         0 SW   [spi2]
  426 root         0 SW   [napi/mtk_eth-5]
  427 root         0 SW   [napi/mtk_eth-6]
  466 root         0 IW<  [kworker/R-mld]
  467 root         0 IW   [kworker/1:8-dev]
  468 root         0 IW<  [kworker/R-ipv6_]
  469 root         0 IW   [kworker/1:9-rcu]
  470 root         0 IW<  [kworker/1:1H-kb]
  471 root         0 IW<  [kworker/R-dsa_o]
  472 root         0 IW<  [kworker/R-kstrp]
  473 root         0 IW   [kworker/1:10]
  636 root         0 IW   [kworker/u4:3-ev]
  656 root         0 SW   [irq/85-aerdrv]
  705 root         0 SW   [irq/15-gpio-key]
  706 root         0 SW   [irq/16-gpio-key]
  712 root         0 IW<  [kworker/R-nvme-]
  714 root         0 IW<  [kworker/R-nvme-]
  715 root         0 IW<  [kworker/R-nvme-]
  728 root         0 IW   [kworker/u4:4-ev]
  767 root         0 IW<  [kworker/1:2H]
  857 root         0 SW   [ubifs_bgt0_5]
  863 root         0 IW<  [kworker/R-tpm_d]
  965 ubus      1472 S    /sbin/ubusd
  971 root      1336 S    /bin/login -f root
 1011 root      1088 S    /sbin/urngd
 1091 root         0 IW<  [kworker/R-rpcio]
 1092 root         0 IW<  [kworker/R-xprti]
 1099 root         0 IW<  [kworker/R-nfsio]
 1106 root         0 SW   [irq/90-10320000]
 1107 root         0 IW<  [kworker/R-wq_ri]
 1108 root         0 SW   [irq/91-10320000]
 1109 root         0 IW<  [kworker/R-wq_ri]
 1110 root         0 SW   [irq/92-10320000]
 1111 root         0 IW<  [kworker/R-wq_ri]
 1112 root         0 SW   [irq/93-10320000]
 1113 root         0 IW<  [kworker/R-wq_ri]
 1136 root         0 IW<  [kworker/R-cfg80]
 1143 root         0 SW   [napi/phy0-7]
 1144 root         0 SW   [napi/phy0-8]
 1145 root         0 SW   [napi/phy0-9]
 1146 root         0 SW   [napi/phy0-10]
 1147 root         0 SW   [napi/phy0-11]
 1148 root         0 SW   [napi/phy0-12]
 1162 root         0 SW   [mt76-tx phy0]
 1350 logd      2064 S    /sbin/logd -S 128
 1404 root      3696 S    /sbin/rpcd -s /var/run/ubus/ubus.sock -t 30
 1452 root         0 IW<  [kworker/0:2H]
 1755 root      1132 S    /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
 1873 rpc       1472 S    /usr/sbin/rpcbind -f -w
 1923 root      2852 S    {hostapd} /sbin/ujail -t 5 -n hostapd -U network -G 
 1924 root      2852 S    {wpa_supplicant} /sbin/ujail -t 5 -n wpa_supplicant 
 1958 network   5060 S    /usr/sbin/wpa_supplicant -n -s -g /var/run/wpa_suppl
 1961 network   5340 S    /usr/sbin/hostapd -s -g /var/run/hostapd/global
 1988 root      2652 S    /sbin/netifd
 2101 root      1652 S    /usr/sbin/odhcpd
 2226 root      3036 S    /usr/sbin/uhttpd -f -h /www -r OpenWrt-One -x /cgi-b
 2393 root         0 SW   [irq/53-mdio-bus]
 3045 root      2852 S    {ntpd} /sbin/ujail -t 5 -n ntpd -U ntp -G ntp -C /et
 3105 ntp       1336 S    /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0.
 3120 root         0 IW   [lockd]
 3142 root         0 IW   [nfsd]
 3143 root         0 IW   [nfsd]
 3144 root         0 IW   [nfsd]
 3145 root         0 IW   [nfsd]
 3146 root         0 IW   [nfsd]
 3147 root         0 IW   [nfsd]
 3148 root         0 IW   [nfsd]
 3149 root         0 IW   [nfsd]
 3158 root      1316 S    /usr/sbin/rpc.statd -p 32778 -o 32779 -F
 3159 root      1908 S    /usr/sbin/rpc.mountd -p 32780 -F
 3207 root      1000 S    /usr/sbin/ubihealthd -f -d /dev/ubi0
 3370 root      1104 S    odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth1
 3809 root      1352 S    -ash
 4557 root      1492 S    /usr/sbin/pppd nodetach ipparam wan ifname pppoe-wan
 4862 root      2852 S    {dnsmasq} /sbin/ujail -t 5 -n dnsmasq -u -l -r /bin/
 4886 dnsmasq   1592 S    /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c
 4999 root      1344 R    ps
root@OpenWrt-One:~#

... and service ...

root@OpenWrt-One:~# service
Usage: service <service> [command]
/etc/init.d/boot              	   enabled	   stopped
/etc/init.d/bootcount         	   enabled	   stopped
/etc/init.d/cron              	   enabled	   stopped
/etc/init.d/dnsmasq           	   enabled	   running
/etc/init.d/done              	   enabled	   stopped
/etc/init.d/dropbear          	   enabled	   running
/etc/init.d/firewall          	   enabled	   stopped
/etc/init.d/fstab             	   enabled	   stopped
/etc/init.d/gpio_switch       	   enabled	   stopped
/etc/init.d/led               	   enabled	   stopped
/etc/init.d/log               	   enabled	   running
/etc/init.d/network           	   enabled	   running
/etc/init.d/nfsd              	   enabled	   running
/etc/init.d/odhcpd            	   enabled	   running
/etc/init.d/packet_steering   	   enabled	   stopped
/etc/init.d/rpcbind           	   enabled	   running
/etc/init.d/rpcd              	   enabled	   running
/etc/init.d/sysctl            	   enabled	   stopped
/etc/init.d/sysfixtime        	   enabled	   stopped
/etc/init.d/sysntpd           	   enabled	   running
/etc/init.d/system            	   enabled	   stopped
/etc/init.d/ubihealthd        	   enabled	   running
/etc/init.d/ucitrack          	   enabled	   stopped
/etc/init.d/uhttpd            	   enabled	   running
/etc/init.d/umount            	   enabled	   stopped
/etc/init.d/urandom_seed      	   enabled	   stopped
/etc/init.d/urngd             	   enabled	   running
/etc/init.d/wpad              	   enabled	   running
root@OpenWrt-One:~#

... lastly netstat ...

root@OpenWrt-One:~# netstat -tl
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       
tcp        0      0 OpenWrt-A.peritonlane:domain 0.0.0.0:*               LISTEN      
tcp        0      0 localhost:domain        0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:32780           0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:32778           0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:32777           0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:nfs             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:ssh             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:www             0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:sunrpc          0.0.0.0:*               LISTEN      
tcp        0      0 31.96.230.177:domain    0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:https           0.0.0.0:*               LISTEN      
tcp        0      0 fe80::2205:b6ff:feff:fa00:domain :::*                    LISTEN      
tcp        0      0 OpenWrt-One.peritonlane:domain :::*                    LISTEN      
tcp        0      0 :::32780                :::*                    LISTEN      
tcp        0      0 :::32778                :::*                    LISTEN      
tcp        0      0 :::32777                :::*                    LISTEN      
tcp        0      0 :::nfs                  :::*                    LISTEN      
tcp        0      0 :::ssh                  :::*                    LISTEN      
tcp        0      0 :::www                  :::*                    LISTEN      
tcp        0      0 :::sunrpc               :::*                    LISTEN      
tcp        0      0 fe80::2205:b6ff:feff:fa01:domain :::*                    LISTEN      
tcp        0      0 :::https                :::*                    LISTEN      
tcp        0      0 localhost:domain        :::*                    LISTEN      
root@OpenWrt-One:~#
7

your router doesn't agree with you about web access being unavailable :wink:

you' haven't by any chance simply connected to the wrong port ?
AFAIK the PoE port is by default the WAN port.

8

The LAN and WAN ports are swapped to power the One from my Netgear switch.
See: our conversation here: OpenWRT One swap LAN and WAN port

1 Like
9

unless you've done a reset :wink:

you can always check /etc/config/network, verify the interface change's still there.

I still think there issue's elsewhere, not "The One" itself.

10

Even easier ... It will not power-up unless it is in the correct port!

Sorry. Don't understand? Do you think it may be the M.2 NVMe?

11

On a side note, this doesn’t look good:

[   27.930079] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   34.154202] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
12

Do you think it may be informative to undo the LAN/WAN port swap?

13

it would, if the device is reset, but the cable remains in the same port as before.

which is kind of the scenario's we're looking at, everything is up, but you keep trying to access the router through the (now) firewalled WAN port.

PoE won't move just because you change the port assignments :wink:

14

Ah... Not sure I understand (but that my problem!), so I'm checking.

As you know, this is the factory config for /etc/config/network:

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fda8:6121:42cb::/48'
	option packet_steering '1'

config device
	option name 'br-lan'
	option type 'bridge'
	list ports 'eth1'

config interface 'lan'
	option device 'br-lan'
	option proto 'static'
	option ipaddr '192.168.0.254'
	option netmask '255.255.255.0'
	option ip6assign '60'
	option gateway '192.168.0.1'
	list dns '192.168.0.1'

config interface 'wan'
	option device 'eth0'
	option proto 'pppoe'
	option username 'IPS Username'
	option password 'ISP Password'
	option ipv6 'auto'

config interface 'wan6'
	option device 'eth0'
	option proto 'dhcpv6'

And this is my /etc/config/network (read while the NVMe Card is inserted):

config interface 'loopback'
	option device 'lo'
	option proto 'static'
	option ipaddr '127.0.0.1'
	option netmask '255.0.0.0'

config globals 'globals'
	option ula_prefix 'fda8:6121:42cb::/48'
	option packet_steering '1'

config device
	option name 'br-lan'
	option type 'bridge'
	list ports 'eth0'

config interface 'lan'
	option device 'br-lan'
	option proto 'static'
	option ipaddr '192.168.0.1'
	option netmask '255.255.255.0'
	option ip6assign '60'
	option gateway '192.168.0.1'
	list dns '192.168.0.1'

config interface 'wan'
	option device 'eth1'
	option proto 'pppoe'
	option username 'ISP Username'
	option password 'ISP Password'
	option ipv6 'auto'

config interface 'wan6'
	option device 'eth1'
	option proto 'dhcpv6'

config route
	option interface 'lan'
	option target '192.168.4.0/24'
	option gateway '192.168.0.2'

config route
	option interface 'lan'
	option target '192.168.8.0/24'
	option gateway '192.168.0.2'

One change of eth1 to eth0
Two changes of eth0 to eth1

So /etc/config/network is the same with the NVMe inserted or removed:

15

Well eth0 is now br-lan and it’s link state is only negotiated at 100Mbps. It’s hard to say why - could be bad cable/connector, or the switch port supplying POE power can only negotiate @100Mbps . . . But it’s a bottleneck you’ll need to resolve at some point.

You can check what each port is negotiating at with:
cat /sys/class/net/eth0/speed and cat /sys/class/net/eth1/speed

Just leave it as it is for now. concentrate on one issue at a time.

16

Dho... Duff cable. Didn't notice. Thank you.

BusyBox v1.36.1 (2025-02-03 23:09:37 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 24.10.0, r28427-6df0e3d02a
 -----------------------------------------------------
root@OpenWrt-One:~# cat /sys/class/net/eth0/speed
1000
root@OpenWrt-One:~# cat /sys/class/net/eth1/speed
1000
root@OpenWrt-One:~#
17

Install nvme-cli and then issue:
nvme list /dev/nvme0n1 -v and
nvme smart-log /dev/nvme0n1 -v

I suspect these will give a good status.

18

WoooHooo....
Could it really have been the duff cable????

Anyway here is the nvme-cli logs...

root@OpenWrt-One:~# nvme list /dev/nvme0n1 -v

[   67.958153] block nvme0n1: No UUID available providing old NGUID
Subsystem        Subsystem-NQN                                                                                    Controllers
---------------- ------------------------------------------------------------------------------------------------ ----------------
nvme-subsys0     nqn.2023-12.com.skhynix:nvme:nvm-subsystem-sn-4YCCN03031010CP0I                                  nvme0

Device           Cntlid SN                   MN                                       FR       TxPort Address        Slot   Subsystem    Namespaces      
---------------- ------ -------------------- ---------------------------------------- -------- ------ -------------- ------ ------------ ----------------
nvme0    1      4YCCN03031010CP0I    SKHynix_HFS256GEJ4X112N                  51040C31 pcie   0000:01:00.0          nvme-subsys0 nvme0n1

Device            Generic           NSID       Usage                      Format           Controllers     
----------------- ----------------- ---------- -------------------------- ---------------- ----------------
/dev/nvme0n1 /dev/ng0n1   0x1        256.06  GB / 256.06  GB    512   B +  0 B   nvme0
root@OpenWrt-One:~#

 
root@OpenWrt-One:~# nvme smart-log /dev/nvme0n1 -v

latency      : 3480 us
Smart Log for NVME device:nvme0n1 namespace-id:ffffffff
critical_warning			: 0
temperature				: 27 °C (300 K)
available_spare				: 100%
available_spare_threshold		: 10%
percentage_used				: 0%
endurance group critical warning summary: 0
Data Units Read				: 126646 (64.84 GB)
Data Units Written			: 206650 (105.80 GB)
host_read_commands			: 1301242
host_write_commands			: 1291466
controller_busy_time			: 34
power_cycles				: 32
power_on_hours				: 4
unsafe_shutdowns			: 11
media_errors				: 0
num_err_log_entries			: 0
Warning Temperature Time		: 0
Critical Composite Temperature Time	: 0
Temperature Sensor 1           : 32 °C (305 K)
Temperature Sensor 2           : 27 °C (300 K)
Thermal Management T1 Trans Count	: 0
Thermal Management T2 Trans Count	: 0
Thermal Management T1 Total Time	: 0
Thermal Management T2 Total Time	: 0
root@OpenWrt-One:~# 
root@OpenWrt-One:~#

Thank you all for your help.
Regards, M.

19

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.