The HUASIFEI WH3000 and emmc model ( aka Fudy MT3000) are Wi-Fi 6 5G cellular routers, based on MediaTek MT7981A SoC.
Specifications:
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8G
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
UART:
3.3V, TX, RX, GND / 115200 8N1
what kind of help are you looking for ?
add device support to openwrt
OK, get the boot log from OEM web ui
Show where you would download firmware upgrades
Hi, I am also happy owner of this device. Just received it yesterday. Originally it was on QWRT 25.01.25. I've made backups of all mmcblck0 partitions via dd and then flashed immortalWRT on it via sysupgrade since they have it on their firmware-selector at immortalWRT website. Everything works good (at leat it seems so to me). I can share immortalWRT logs if it will suit?
Official firmware is here https://www.huasifei.com/wp-content/uploads/gujian/QWRT-R24.12.30-mediatek-mt7981-mt7981-huasifei-wh3000-emmc-squashfs-sysupgrade.zip
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.73 (buildbot@buildbot.infra.immortalwrt.org) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r32824-6a73dae98c9c) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Wed Feb 5 08:32:41 2025
[ 0.000000] Machine model: Huasifei WH3000 eMMC version
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[ 0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000
[ 0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000
[ 0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff]
[ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff]
[ 0.000000] node 0: [mem 0x0000000048000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 28 pages/cpu s74920 r8192 d31576 u114688
[ 0.000000] pcpu-alloc: s74920 r8192 d31576 u114688 alloc=284096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: root=PARTLABEL=rootfs rootwait rootfstype=squashfs,f2fs
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 2.
[ 0.000000] software IO TLB: mapped [mem 0x000000007fb18000-0x000000007fc18000] (1MB)
[ 0.000000] Memory: 1004104K/1048576K available (9920K kernel code, 1568K rwdata, 6804K rodata, 512K init, 319K bss, 44472K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000247] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000256] pid_max: default: 32768 minimum: 301
[ 0.003162] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.003174] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005386] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.005943] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[ 0.006108] rcu: Hierarchical SRCU implementation.
[ 0.006112] rcu: Max phase no-delay instances is 1000.
[ 0.006656] smp: Bringing up secondary CPUs ...
[ 0.007075] Detected VIPT I-cache on CPU1
[ 0.007124] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.007158] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.007235] smp: Brought up 1 node, 2 CPUs
[ 0.007241] SMP: Total of 2 processors activated.
[ 0.007244] CPU features: detected: 32-bit EL0 Support
[ 0.007247] CPU features: detected: CRC32 instructions
[ 0.007281] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.007285] CPU: All CPU(s) started at EL2
[ 0.007287] alternatives: applying system-wide alternatives
[ 0.011097] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.011115] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.012120] pinctrl core: initialized pinctrl subsystem
[ 0.013244] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.013887] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.013919] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.013952] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.014332] thermal_sys: Registered thermal governor 'fair_share'
[ 0.014337] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.014340] thermal_sys: Registered thermal governor 'step_wise'
[ 0.014342] thermal_sys: Registered thermal governor 'user_space'
[ 0.014418] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.014485] ASID allocator initialised with 65536 entries
[ 0.015443] pstore: Using crash dump compression: deflate
[ 0.015449] pstore: Registered ramoops as persistent store backend
[ 0.015452] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.016863] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[ 0.022963] Modules: 27952 pages in range for non-PLT usage
[ 0.022972] Modules: 519472 pages in range for PLT usage
[ 0.030484] cryptd: max_cpu_qlen set to 1000
[ 0.031812] SCSI subsystem initialized
[ 0.032049] libata version 3.00 loaded.
[ 0.034635] clocksource: Switched to clocksource arch_sys_counter
[ 0.036986] NET: Registered PF_INET protocol family
[ 0.037128] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.038928] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.038950] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.038960] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.039014] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.039213] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.039622] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[ 0.039752] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.039776] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.040086] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.040111] NET: Registered PF_XDP protocol family
[ 0.040124] PCI: CLS 0 bytes, default 64
[ 0.042190] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.047180] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.047190] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.080395] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.092013] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.095986] printk: console [ttyS0] disabled
[ 0.116397] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[ 0.116443] printk: console [ttyS0] enabled
[ 0.893764] loop: module loaded
[ 1.026353] i2c_dev: i2c /dev entries driver
[ 1.032504] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.075778] NET: Registered PF_INET6 protocol family
[ 1.081746] Segment Routing with IPv6
[ 1.085471] In-situ OAM (IOAM) with IPv6
[ 1.089452] NET: Registered PF_PACKET protocol family
[ 1.094520] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.107672] 8021q: 802.1Q VLAN Support v1.8
[ 1.137308] phy phy-soc:usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[ 1.153447] mmc0: new high speed MMC card at address 0001
[ 1.160212] mmcblk0: mmc0:0001 8GME4R 7.28 GiB
[ 1.168373] GPT:partition_entry_array_crc32 values don't match: 0xbdf77fab != 0x6232ab93
[ 1.176478] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 1.183857] GPT:14942207 != 15269887
[ 1.187426] GPT:Alternate GPT header not at the end of the disk.
[ 1.193416] GPT:14942207 != 15269887
[ 1.196987] GPT: Use GNU Parted to correct GPT errors.
[ 1.202135] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 1.207952] mmcblk0boot0: mmc0:0001 8GME4R 4.00 MiB
[ 1.214129] mmcblk0boot1: mmc0:0001 8GME4R 4.00 MiB
[ 1.219453] mmcblk0rpmb: mmc0:0001 8GME4R 512 KiB, chardev (250:0)
[ 1.648449] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc082600000, irq 74
[ 1.658600] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc082600000, irq 74
[ 1.669016] clk: Disabling unused clocks
[ 1.676241] VFS: Mounted root (squashfs filesystem) readonly on device 179:6.
[ 1.683568] Freeing unused kernel memory: 512K
[ 1.688387] Run /sbin/init as init process
[ 1.692480] with arguments:
[ 1.695458] /sbin/init
[ 1.698153] with environment:
[ 1.701280] HOME=/
[ 1.703627] TERM=linux
[ 1.873448] init: Console is alive
[ 1.877069] init: - watchdog -
[ 2.541515] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 2.602963] usbcore: registered new interface driver usbfs
[ 2.608551] usbcore: registered new interface driver hub
[ 2.613906] usbcore: registered new device driver usb
[ 2.626288] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.642215] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.647513] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 2.657921] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000200010
[ 2.667123] xhci-mtk 11200000.usb: irq 79, io mem 0x11200000
[ 2.672897] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.678237] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 2.685650] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 2.693210] hub 1-0:1.0: USB hub found
[ 2.697122] hub 1-0:1.0: 1 port detected
[ 2.701503] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.710115] hub 2-0:1.0: USB hub found
[ 2.713913] hub 2-0:1.0: 1 port detected
[ 2.726401] usbcore: registered new interface driver usb-storage
[ 2.733761] usbcore: registered new interface driver uas
[ 2.739398] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.756985] init: - preinit -
[ 3.224705] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY (C45)] (irq=53)
[ 3.239042] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
[ 7.518243] mount_root: loading kmods from internal overlay
[ 7.536602] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 7.544816] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 7.844971] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[ 7.852969] block: unable to load configuration (fstab: Entry not found)
[ 7.859815] block: attempting to load /tmp/overlay/etc/config/fstab
[ 7.866172] block: unable to load configuration (fstab: Entry not found)
[ 7.872907] block: attempting to load /etc/config/fstab
[ 7.881448] block: unable to load configuration (fstab: Entry not found)
[ 7.888275] block: no usable configuration
[ 7.893137] loop0: detected capacity change from 0 to 4194304
[ 7.934718] loop0: detected capacity change from 4194304 to 4176512
[ 8.263332] F2FS-fs (loop0): Mounted with checkpoint version = 3999c7a7
[ 8.270182] block: attempting to load /tmp/f2fs_cfg/upper/etc/config/fstab
[ 8.279114] block: extroot: not configured
[ 8.302094] loop0: detected capacity change from 0 to 4194304
[ 8.344833] loop0: detected capacity change from 4194304 to 4176512
[ 8.356630] F2FS-fs (loop0): Mounted with checkpoint version = 3999c7a9
[ 8.363740] mount_root: loading kmods from internal overlay
[ 8.398300] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 8.407171] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 8.585948] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[ 8.593348] block: extroot: not configured
[ 8.598565] block: attempting to load /tmp/f2fs_cfg/upper/etc/config/fstab
[ 8.605875] block: extroot: not configured
[ 8.611578] mount_root: switching to f2fs overlay
[ 8.619136] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.631292] urandom-seed: Seeding with /etc/urandom.seed
[ 8.654593] random: procd: uninitialized urandom read (4 bytes read)
[ 8.657996] procd: - early -
[ 8.664023] procd: - watchdog -
[ 9.207551] procd: - watchdog -
[ 9.211186] procd: - ubus -
[ 10.254658] random: crng init done
[ 10.263826] procd: - init -
[ 10.874199] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.952404] NET: Registered PF_ALG protocol family
[ 10.970343] tun: Universal TUN/TAP device driver, 1.6
[ 10.979786] GACT probability on
[ 10.995633] Mirror/redirect action on
[ 11.017273] u32 classifier
[ 11.019986] input device check on
[ 11.023637] Actions configured
[ 11.050805] urngd: v1.0.2 started.
[ 11.065130] ntfs3: Enabled Linux POSIX ACLs support
[ 11.073322] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[ 11.146592] usbcore: registered new interface driver cdc_wdm
[ 11.159126] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[ 11.166646] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[ 11.209872] usbcore: registered new interface driver ums-alauda
[ 11.235810] usbcore: registered new interface driver ums-cypress
[ 11.243054] usbcore: registered new interface driver ums-datafab
[ 11.251279] usbcore: registered new interface driver ums-freecom
[ 11.258744] usbcore: registered new interface driver ums-isd200
[ 11.266135] usbcore: registered new interface driver ums-jumpshot
[ 11.273419] usbcore: registered new interface driver ums-karma
[ 11.280765] usbcore: registered new interface driver ums-sddr09
[ 11.288021] usbcore: registered new interface driver ums-sddr55
[ 11.295249] usbcore: registered new interface driver ums-usbat
[ 11.306014] usbcore: registered new interface driver usbserial_generic
[ 11.312612] usbserial: USB Serial support registered for generic
[ 11.320339] usbcore: registered new interface driver cdc_ether
[ 11.328405] usbcore: registered new interface driver cdc_ncm
[ 11.499165] mt798x-wmac 18000000.wifi: attaching wed device 0 version 2
[ 11.586578] platform 15010000.wed: MTK WED WO Firmware Version: DEV_000000, Build Time: 20221208202138
[ 11.595921] platform 15010000.wed: MTK WED WO Chip ID 00 Region 3
[ 12.125152] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823161240a
[ 12.125152]
[ 12.314071] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823161304
[ 12.429904] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823161841
[ 12.527672] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[ 12.587040] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[ 12.674468] PPP generic driver version 2.4.2
[ 12.680682] PPP MPPE Compression module registered
[ 12.688118] NET: Registered PF_PPPOX protocol family
[ 12.696241] usbcore: registered new interface driver qmi_wwan
[ 12.705654] usbcore: registered new interface driver cdc_mbim
[ 12.715051] usbcore: registered new interface driver option
[ 12.720741] usbserial: USB Serial support registered for GSM modem (1-port)
[ 12.730619] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.278017] bridger[1583]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
[ 18.484710] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY (C45)] (irq=53)
[ 18.499030] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
[ 18.545358] br-lan: port 1(eth0) entered blocking state
[ 18.550589] br-lan: port 1(eth0) entered disabled state
[ 18.555869] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[ 18.562801] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[ 18.597743] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[ 18.607379] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[ 20.881155] br-lan: port 2(phy0-ap0) entered blocking state
[ 20.886831] br-lan: port 2(phy0-ap0) entered disabled state
[ 20.892458] mt798x-wmac 18000000.wifi phy0-ap0: entered allmulticast mode
[ 20.899542] mt798x-wmac 18000000.wifi phy0-ap0: entered promiscuous mode
[ 21.077852] br-lan: port 3(phy1-ap0) entered blocking state
[ 21.083438] br-lan: port 3(phy1-ap0) entered disabled state
[ 21.089151] mt798x-wmac 18000000.wifi phy1-ap0: entered allmulticast mode
[ 21.096199] mt798x-wmac 18000000.wifi phy1-ap0: entered promiscuous mode
[ 21.103055] br-lan: port 3(phy1-ap0) entered blocking state
[ 21.108666] br-lan: port 3(phy1-ap0) entered forwarding state
[ 22.794832] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 31.623422] br-lan: port 2(phy0-ap0) entered blocking state
[ 31.629019] br-lan: port 2(phy0-ap0) entered forwarding state
[ 34.901856] mt798x-wmac 18000000.wifi phy0-ap0: left allmulticast mode
[ 34.908478] mt798x-wmac 18000000.wifi phy0-ap0: left promiscuous mode
[ 34.915112] br-lan: port 2(phy0-ap0) entered disabled state
[ 35.159968] mt798x-wmac 18000000.wifi phy1-ap0: left allmulticast mode
[ 35.166582] mt798x-wmac 18000000.wifi phy1-ap0: left promiscuous mode
[ 35.173116] br-lan: port 3(phy1-ap0) entered disabled state
[ 36.692041] br-lan: port 2(phy0-ap0) entered blocking state
[ 36.697721] br-lan: port 2(phy0-ap0) entered disabled state
[ 36.703361] mt798x-wmac 18000000.wifi phy0-ap0: entered allmulticast mode
[ 36.710447] mt798x-wmac 18000000.wifi phy0-ap0: entered promiscuous mode
[ 36.717454] br-lan: port 2(phy0-ap0) entered blocking state
[ 36.723037] br-lan: port 2(phy0-ap0) entered forwarding state
[ 37.006564] br-lan: port 2(phy0-ap0) entered disabled state
[ 37.177240] br-lan: port 3(phy1-ap0) entered blocking state
[ 37.182825] br-lan: port 3(phy1-ap0) entered disabled state
[ 37.188528] mt798x-wmac 18000000.wifi phy1-ap0: entered allmulticast mode
[ 37.195580] mt798x-wmac 18000000.wifi phy1-ap0: entered promiscuous mode
[ 37.202458] br-lan: port 3(phy1-ap0) entered blocking state
[ 37.208068] br-lan: port 3(phy1-ap0) entered forwarding state
[ 47.569135] br-lan: port 2(phy0-ap0) entered blocking state
[ 47.574742] br-lan: port 2(phy0-ap0) entered forwarding state
[ 2339.419171] mtk_soc_eth 15100000.ethernet eth1: Link is Down
[ 2341.827066] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2341.835622] br-lan: port 1(eth0) entered blocking state
[ 2341.840889] br-lan: port 1(eth0) entered forwarding state
[ 2400.266591] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 2400.273129] br-lan: port 1(eth0) entered disabled state
[ 2404.924416] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2414.282309] mtk_soc_eth 15100000.ethernet eth1: Link is Down
[ 2421.560830] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
P.S. I would be happy to get at least some key points from where to start for building official OpenWRT and adding it to official branch later. I am ready to provide any info and test anything on my router since I have a spare one for tests.
It's a supported device on Immortalwrt, I'm hunting the git commit to see if it can be used.
This was also raised on the Openwrt git:
Commits below are the support added for Immortalwrt:
Missing emmc dependency
Should be a case of raising a PR commit.
@dunsky if I make the changes later are you up for testing?
@hecatae Yes, please! I have been messing around with this router for a while now. I've found UART it's just 4 pins - no need to solder anything, I've ordered USB TTL, should come tomorrow. Also, it came with 2GB mmcblck0p6 partition from the factory and there was an empty mmcblck0p7 partition with another 7.3GB left which I've been able to merge finally. Huasifei support is useless, they were saying nonsense that though the eMMC chip is 8GB it could only use 2GB for storage.
Sorry for the details. Please let me know if there is anything I can do. I am ready to test. Following this thread. Hopefully will not miss any notifications from now.
thank you, compiling, will be in touch soon
attached is openwrt 24.10.0 for the wh3000 with all the immortalwrt device commits copied across.
there's a initramfs and a sysupgrade, I would recommend testing the initramfs first.
@hecatae Thanks a lot! I would flash it now. Do I have to sysupgrade -n it? First initramfs-kernel, boot, test and then squashfs-sysupgrade from initramfs mode?
wait for your USB TTL tomorrow please, I cannot promise what I have compiled will boot.
I've flashed via sysupgrade -F first initramsf, it boots fine, then squashfs-sysupgrade. So far everything is working. Do you have any suggestions on what should I test?
Please test all the things, please test WiFi, factory reset, restoring to Stock Firmware etc.
Wifi power, jp/us/eu dfs, all mac addreesses,leds
I think it's fine that some kernel modules can not be installed on this build for now, right? Like kmod-nft-proxy
You can load kmods from your build tree.
you can't install any kmods coming from the official repo.
do you want me to build all packages?
If it's possible, I would love to give it a try as well. Right now I am still testing and everything looks fine to me. But my usual case is that I am installing Clash (Mihomo) on it to use different tunnels, I use Zerotier as well. Do you think it would be nice to test this firmware at least for a few days as a daily driver?
Also @Doanduy09 topicstarter OP is silent here but he mentioned something about wifi issues in a github issue. "He said it doesn't have MDT and Hnat drivers". I don't know what is it and I've used this router on immortalWRT for a few days and my experience is similar to what I am having on this vanilla build now.
One thing I havent tested yet is to flash back to the "stock" QWRT. I'll try now.