Hi, everyone!
I've just flashed image from this topic, everithing work much better than on OEM firmware. But I've got an issue with p910nd printserver installing. The # ls /dev/usb/lp*
returns ls: /dev/usb/lp*: No such file or directory
.
On firmwares from gl-inet this worked fine. Maybe I need to install any additional drivers or some?
I'll be very glad to get any suggestions, thanks.
is there anything in /dev/lp* ?
did you install the kmod-usb-printer package ?
This might be relevant further down the road Printer server not working
kmod-usb-printer is installed, and ls: /dev/lp*: No such file or directory
this is what I have with ls /dev/
root@OpenWrt:~# ls /dev/*
/dev/console /dev/mtd1 /dev/mtd5ro /dev/mtdblock4 /dev/sda /dev/ttyS15 /dev/ubi_ctrl
/dev/cpu_dma_latency /dev/mtd1ro /dev/mtd6 /dev/mtdblock5 /dev/tty /dev/ttyS2 /dev/urandom
/dev/full /dev/mtd2 /dev/mtd6ro /dev/mtdblock6 /dev/ttyS0 /dev/ttyS3 /dev/watchdog
/dev/gpiochip0 /dev/mtd2ro /dev/mtd7 /dev/mtdblock7 /dev/ttyS1 /dev/ttyS4 /dev/zero
/dev/hwrng /dev/mtd3 /dev/mtd7ro /dev/null /dev/ttyS10 /dev/ttyS5
/dev/kmsg /dev/mtd3ro /dev/mtdblock0 /dev/port /dev/ttyS11 /dev/ttyS6
/dev/log /dev/mtd4 /dev/mtdblock1 /dev/ppp /dev/ttyS12 /dev/ttyS7
/dev/mtd0 /dev/mtd4ro /dev/mtdblock2 /dev/ptmx /dev/ttyS13 /dev/ttyS8
/dev/mtd0ro /dev/mtd5 /dev/mtdblock3 /dev/random /dev/ttyS14 /dev/ttyS9
/dev/bsg:
0:0:0:0 1:0:0:0
/dev/bus:
usb
/dev/pts:
0 ptmx
which printer is it ?
and what does lsusb say ?
root@OpenWrt:~# lsusb
Bus 002 Device 003: ID 05e3:0752 Generic USB Storage
Bus 001 Device 002: ID 03f0:042a Hewlett-Packard HP LaserJet Professional M1132 MFP
Bus 001 Device 001: ID 1d6b:0002 Linux 5.4.108 ehci_hcd EHCI Host Controller
Bus 002 Device 002: ID 05e3:0618 USB2.0 Hub
Bus 002 Device 001: ID 1d6b:0002 Linux 5.4.108 ehci_hcd EHCI Host Controller
ok, so it's seen by the usb.
reboot
afterwards, unplug, and plug the printer back in again, and post dmesg.
[ 0.000000] Linux version 5.4.108 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16372-e62ace0ecf)) #0 Wed Mar 31 00:32:51 2021
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is GL.iNet GL-AR750S (NOR)
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 121348K/131072K available (5535K kernel code, 180K rwdata, 1228K rodata, 1240K init, 210K bss, 9724K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] random: get_random_bytes called from start_kernel+0x308/0x4fc with crng_init=0
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008227] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.046724] pid_max: default: 32768 minimum: 301
[ 0.051720] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.059435] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071479] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.081795] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.089075] pinctrl core: initialized pinctrl subsystem
[ 0.096917] NET: Registered protocol family 16
[ 0.107637] GPIO line 7 (usb-vbus) hogged as output/high
[ 0.135026] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.148074] clocksource: Switched to clocksource MIPS
[ 0.154505] NET: Registered protocol family 2
[ 0.159946] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.168825] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.176913] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.184355] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.191186] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.198122] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.205761] NET: Registered protocol family 1
[ 0.210413] PCI: CLS 0 bytes, default 32
[ 0.218005] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.230981] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.237169] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.259890] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.271148] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.278264] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.287091] printk: console [ttyS0] disabled
[ 0.291682] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.300794] printk: console [ttyS0] enabled
[ 0.309856] printk: bootconsole [early0] disabled
[ 0.329899] spi-nand spi0.1: GigaDevice SPI NAND was found.
[ 0.335710] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 0.344526] 1 fixed-partitions partitions found on MTD device spi0.1
[ 0.351127] Creating 1 MTD partitions on "spi0.1":
[ 0.356101] 0x000000000000-0x000008000000 : "nand_ubi"
[ 0.520569] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.525574] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.532145] Creating 4 MTD partitions on "spi0.0":
[ 0.537109] 0x000000000000-0x000000040000 : "u-boot"
[ 0.543081] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.549465] 0x000000050000-0x000000060000 : "art"
[ 0.555198] 0x000000060000-0x000001000000 : "firmware"
[ 0.564530] 2 uimage-fw partitions found on MTD device firmware
[ 0.570690] Creating 2 MTD partitions on "firmware":
[ 0.575843] 0x000000000000-0x000000240000 : "kernel"
[ 0.581783] 0x000000240000-0x000000fa0000 : "rootfs"
[ 0.587761] mtd: device 6 (rootfs) set to be root filesystem
[ 0.595273] 1 squashfs-split partitions found on MTD device rootfs
[ 0.601728] 0x000000570000-0x000000fa0000 : "rootfs_data"
[ 0.609037] libphy: Fixed MDIO Bus: probed
[ 1.168067] random: fast init done
[ 1.248445] libphy: ag71xx_mdio: probed
[ 1.255496] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.843557] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.854847] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[ 1.863179] NET: Registered protocol family 10
[ 1.872060] Segment Routing with IPv6
[ 1.875999] NET: Registered protocol family 17
[ 1.880683] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.894075] 8021q: 802.1Q VLAN Support v1.8
[ 1.900714] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 1.907078] MEM 0x0000000012000000..0x0000000013ffffff
[ 1.912485] IO 0x0000000000000000..0x0000000000000000
[ 1.918055] PCI host bridge to bus 0000:00
[ 1.922327] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.929433] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.935194] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.942208] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.950423] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000
[ 1.956683] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 1.963750] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.970746] pci 0000:00:00.0: supports D1
[ 1.974897] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.981766] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 1.988655] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 1.996240] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 2.010587] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 2.024737] Freeing unused kernel memory: 1240K
[ 2.029447] This architecture does not have kernel memory protection.
[ 2.036105] Run /sbin/init as init process
[ 2.619980] init: Console is alive
[ 2.623811] init: - watchdog -
[ 3.860756] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.976980] usbcore: registered new interface driver usbfs
[ 3.982768] usbcore: registered new interface driver hub
[ 3.988372] usbcore: registered new device driver usb
[ 4.000956] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.016113] SCSI subsystem initialized
[ 4.024709] ehci-fsl: Freescale EHCI Host controller driver
[ 4.032212] ehci-platform: EHCI generic platform driver
[ 4.037886] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.043821] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.052040] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 4.072084] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.079253] hub 1-0:1.0: USB hub found
[ 4.083516] hub 1-0:1.0: 1 port detected
[ 4.088267] ehci-platform 1b400000.usb: EHCI Host Controller
[ 4.094188] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[ 4.102421] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[ 4.124090] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[ 4.131279] hub 2-0:1.0: USB hub found
[ 4.135543] hub 2-0:1.0: 1 port detected
[ 4.145714] usbcore: registered new interface driver usb-storage
[ 4.152647] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.162586] init: - preinit -
[ 4.542964] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 4.608189] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 4.848876] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.957742] scsi host0: usb-storage 1-1:1.0
[ 4.963843] random: procd: uninitialized urandom read (4 bytes read)
[ 4.978892] hub 2-1:1.0: USB hub found
[ 4.988277] hub 2-1:1.0: 4 ports detected
[ 5.540226] usb 2-1.1: new high-speed USB device number 3 using ehci-platform
[ 5.623568] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.690838] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.737984] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[ 5.756190] scsi host1: usb-storage 2-1.1:1.0
[ 5.970693] scsi 0:0:0:0: CD-ROM HP Smart Install 1.0 PQ: 0 ANSI: 2
[ 6.770694] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 0233 PQ: 0 ANSI: 0
[ 6.786189] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 1 is up
[ 6.792767] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
[ 6.806465] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 6.828273] eth0: link up (1000Mbps/Full duplex)
[ 6.837089] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.850026] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 11.002818] mount_root: loading kmods from internal overlay
[ 11.032771] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.040686] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.499446] jffs2: notice: (542) jffs2_build_xattr_subsystem: complete building xattr subsystem, 139 of xdatum (121 unchecked, 8 orphan) and 164 of xref (9 dead, 1 orphan) found.
[ 11.516467] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.535776] block: extroot: not configured
[ 11.706456] jffs2: notice: (540) jffs2_build_xattr_subsystem: complete building xattr subsystem, 139 of xdatum (121 unchecked, 8 orphan) and 164 of xref (9 dead, 1 orphan) found.
[ 11.728299] mount_root: loading kmods from internal overlay
[ 12.190640] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 12.229250] uhci_hcd: USB Universal Host Controller Interface driver
[ 12.315156] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 12.611175] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.623168] block: extroot: not configured
[ 12.628517] mount_root: switching to jffs2 overlay
[ 12.636638] overlayfs: upper fs does not support tmpfile.
[ 12.647392] urandom-seed: Seeding with /etc/urandom.seed
[ 13.072250] eth0: link down
[ 13.097136] procd: - early -
[ 13.100331] procd: - watchdog -
[ 13.764221] procd: - watchdog -
[ 13.769147] procd: - ubus -
[ 13.787645] urandom_read: 3 callbacks suppressed
[ 13.787651] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.847329] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.854481] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.864272] procd: - init -
[ 14.767795] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.028608] urngd: v1.0.2 started.
[ 15.277030] random: crng init done
[ 15.280582] random: 1 urandom warning(s) missed due to ratelimiting
[ 15.346884] ppdev: user-space parallel port driver
[ 15.502862] lp: driver loaded but no devices found
[ 15.740622] Loading modules backported from Linux version v5.10.16-0-gde53befa79cf
[ 15.748488] Backport generated by backports.git v5.10.16-1-0-g21d2a1d2
[ 15.911879] usbcore: registered new interface driver usblp
[ 15.960361] xt_time: kernel timezone is -0000
[ 16.199706] PPP generic driver version 2.4.2
[ 16.213138] NET: Registered protocol family 24
[ 16.291368] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 16.299505] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 16.424236] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x50.
[ 16.445029] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 16.451709] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 18.399928] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000
[ 18.409492] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 18.421861] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-87-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 61a92df5
[ 18.762312] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d
[ 19.719164] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 19.733704] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 19.740178] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 19.748471] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 25560 iram: 24780'
[ 19.784984] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 19.795263] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 19.907647] ath: EEPROM regdomain sanitized
[ 19.907656] ath: EEPROM regdomain: 0x64
[ 19.907659] ath: EEPROM indicates we should expect a direct regpair map
[ 19.907677] ath: Country alpha2 being used: 00
[ 19.907680] ath: Regpair used: 0x64
[ 20.014785] ath: EEPROM regdomain sanitized
[ 20.014795] ath: EEPROM regdomain: 0x64
[ 20.014799] ath: EEPROM indicates we should expect a direct regpair map
[ 20.014818] ath: Country alpha2 being used: 00
[ 20.014820] ath: Regpair used: 0x64
[ 20.025932] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 20.027772] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 20.068539] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 31.461557] eth0: link up (1000Mbps/Full duplex)
[ 31.474597] br-lan: port 1(eth0.1) entered blocking state
[ 31.480260] br-lan: port 1(eth0.1) entered disabled state
[ 31.486141] device eth0.1 entered promiscuous mode
[ 31.491133] device eth0 entered promiscuous mode
[ 31.497132] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 31.526086] br-lan: port 1(eth0.1) entered blocking state
[ 31.531708] br-lan: port 1(eth0.1) entered forwarding state
[ 32.464175] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 37.512875] br-lan: port 2(wlan1) entered blocking state
[ 37.518434] br-lan: port 2(wlan1) entered disabled state
[ 37.524257] device wlan1 entered promiscuous mode
[ 38.195453] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 38.202272] br-lan: port 2(wlan1) entered blocking state
[ 38.207803] br-lan: port 2(wlan1) entered forwarding state
[ 39.673842] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 39.688627] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 39.694895] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 39.703641] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 25560 iram: 24780'
[ 39.765492] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[ 39.783617] ath10k_pci 0000:00:00.0: rts threshold -1
[ 39.825228] br-lan: port 3(wlan0) entered blocking state
[ 39.830797] br-lan: port 3(wlan0) entered disabled state
[ 39.836620] device wlan0 entered promiscuous mode
[ 43.402496] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 43.409350] br-lan: port 3(wlan0) entered blocking state
[ 43.414893] br-lan: port 3(wlan0) entered forwarding state
[ 385.746372] usb 1-1: USB disconnect, device number 2
[ 390.310737] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 390.473400] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 390.480825] scsi host0: usb-storage 1-1:1.0
[ 391.504394] scsi 0:0:0:0: CD-ROM HP Smart Install 1.0 PQ: 0 ANSI: 2
Found the the solution. At the first start printer exposes himself as host0: usb-storage 1-1:1.0 [ 391.504394] scsi 0:0:0:0: CD-ROM HP Smart Install
after printer restart it exposes normally as USB Bidirectional printer
and ls /dev/usb/lp*
now shows /dev/usb/lp0
as should.
frollic, Thanks a lot for your time and suggestions!
This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.