I'm using your image. Don't want to attempt to build mine until it's more stable to avoid additional noise.
No idea why the partition names are in lowercase.
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.12.32 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r29995-02ae3de72a) 14.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Jun 9 23:10:23 2025
[ 0.000000] Machine model: TCL HH500V
[ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 20 pages/cpu s43352 r8192 d30376 u81920
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 262144
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000126] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000139] pid_max: default: 32768 minimum: 301
[ 0.005097] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005112] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.040477] rcu: Hierarchical SRCU implementation.
[ 0.040487] rcu: Max phase no-delay instances is 1000.
[ 0.040785] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[ 0.050381] smp: Bringing up secondary CPUs ...
[ 0.080313] Detected VIPT I-cache on CPU1
[ 0.080425] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.090379] Detected VIPT I-cache on CPU2
[ 0.090457] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.100283] Detected VIPT I-cache on CPU3
[ 0.100356] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.100437] smp: Brought up 1 node, 4 CPUs
[ 0.100446] SMP: Total of 4 processors activated.
[ 0.100450] CPU: All CPU(s) started at EL1
[ 0.100454] CPU features: detected: 32-bit EL0 Support
[ 0.100460] CPU features: detected: CRC32 instructions
[ 0.100507] alternatives: applying system-wide alternatives
[ 0.100709] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.100968] Memory: 872688K/1048576K available (9088K kernel code, 910K rwdata, 2920K rodata, 9600K init, 302K bss, 172416K reserved, 0K cma-reserved)
[ 0.109682] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.109708] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.109810] 27008 pages in range for non-PLT usage
[ 0.109814] 518528 pages in range for PLT usage
[ 0.111968] pinctrl core: initialized pinctrl subsystem
[ 0.116385] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.116890] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.116929] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.116963] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.117347] thermal_sys: Registered thermal governor 'step_wise'
[ 0.117409] cpuidle: using governor menu
[ 0.117591] ASID allocator initialised with 65536 entries
[ 0.125389] /soc@0/phy@84000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[ 0.125465] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/phy@84000
[ 0.126386] /soc@0/phy@84000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[ 0.128697] /soc@0/phy@84000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000
[ 0.128999] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/phy@84000
[ 0.179105] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.180514] OF: /leds/4g_green: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180548] OF: /leds/4g_blue: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180577] OF: /leds/wifi_red: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180607] OF: /leds/wifi_blue: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180636] OF: /leds/power_blue: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180664] OF: /leds/power_red: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180694] OF: /leds/5g_red: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180723] OF: /leds/5g_green: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180753] OF: /leds/5g_blue: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.180782] OF: /leds/4g_red: could not get #gpio-cells for /soc@0/i2c@78b6000/gpio-expander@91
[ 0.200965] SCSI subsystem initialized
[ 0.201194] usbcore: registered new interface driver usbfs
[ 0.201235] usbcore: registered new interface driver hub
[ 0.201270] usbcore: registered new device driver usb
[ 0.201548] qcom_scm: convention: smc arm 64
[ 0.203328] clocksource: Switched to clocksource arch_sys_counter
[ 0.207084] NET: Registered PF_INET protocol family
[ 0.207263] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.210086] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.210111] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.210126] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.210212] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.210536] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.211027] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, linear)
[ 0.211197] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.211236] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.211555] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.211592] PCI: CLS 0 bytes, default 64
[ 0.224880] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.225624] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.225633] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.228590] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.236100] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[ 0.236262] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[ 0.237631] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.237774] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.239496] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[ 0.239702] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[ 0.239748] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.239922] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[ 0.240176] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.240311] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.240375] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.240577] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.243950] qcom-pcie 20000000.pcie: host bridge /soc@0/pcie@20000000 ranges:
[ 0.244052] qcom-pcie 20000000.pcie: IO 0x0020200000..0x002020ffff -> 0x0000000000
[ 0.244080] qcom-pcie 20000000.pcie: MEM 0x0020220000..0x002fffffff -> 0x0020220000
[ 0.250037] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.254031] msm_serial 78b1000.serial: msm_serial: detected port #1
[ 0.254115] msm_serial 78b1000.serial: uartclk = 19200000
[ 0.254478] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 20, base_baud = 1200000) is a MSM
[ 0.254995] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.255089] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.255479] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.255525] msm_serial: console setup on port #0
[ 0.255562] printk: legacy console [ttyMSM0] enabled
[ 0.364935] qcom-pcie 20000000.pcie: iATU: unroll T, 8 ob, 8 ib, align 4K, limit 1024G
[ 0.375050] msm_serial: driver initialized
[ 1.272405] loop: module loaded
[ 1.273811] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 1.274367] nand: Micron MT29F2G08ABBGAH4
[ 1.280961] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.284934] nand: WARNING: qcom_nand.0: the ECC used on your system (4b/512B) is too weak compared to the one required by the NAND chip (8b/512B)
[ 1.305632] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.306073] spi_master spi0: /soc@0/spi@78b5000/flash@0 has no valid 'reg' property (-22)
[ 1.312659] spi_master spi0: Failed to create SPI device for /soc@0/spi@78b5000/flash@0
[ 1.321312] spmi_pmic_arb 200f000.spmi: PMIC arbiter version v2 (0x20010000)
[ 1.385329] i2c_dev: i2c /dev entries driver
[ 1.386412] aw9523-pinctrl 0-005b: No cache defaults, reading back from HW
[ 1.388973] aw9523-pinctrl 0-005b: Failed to read 2: -6
[ 1.401629] sdhci: Secure Digital Host Controller Interface driver
[ 1.401674] sdhci: Copyright(c) Pierre Ossman
[ 1.406767] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.413304] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 1.420577] NET: Registered PF_INET6 protocol family
[ 1.423870] Segment Routing with IPv6
[ 1.427784] In-situ OAM (IOAM) with IPv6
[ 1.431363] NET: Registered PF_PACKET protocol family
[ 1.435347] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.440515] 8021q: 802.1Q VLAN Support v1.8
[ 1.443370] qcom-pcie 20000000.pcie: Phy link never came up
[ 1.457891] qcom-pcie 20000000.pcie: PCI host bridge to bus 0000:00
[ 1.462746] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.469064] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.474565] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff]
[ 1.480831] pci 0000:00:00.0: [17cb:1002] type 01 class 0x060400 PCIe Root Port
[ 1.485406] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 1.487589] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00000fff]
[ 1.495122] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 1.502056] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.507976] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 1.514555] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.514567] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.519758] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 1.527407] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref]
[ 1.533505] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 1.540309] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.547786] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 1.559081] pci 0000:00:00.0: BAR 0 [mem 0x20220000-0x20220fff]: assigned
[ 1.564645] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 712000 uV
[ 1.564655] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 848000 uV
[ 1.564662] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 912000 uV
[ 1.570891] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.577664] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop=1024000 uV
[ 1.584536] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 1.594474] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 657, quot_offset[ 7]= 0
[ 1.604232] pci_bus 0000:00: resource 5 [mem 0x20220000-0x2fffffff]
[ 1.614031] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 909, quot_offset[ 7]= 250
[ 1.621560] pcieport 0000:00:00.0: PME: Signaling with IRQ 30
[ 1.629051] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1013, quot_offset[ 7]= 100
[ 1.629062] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1201, quot_offset[ 7]= 185
[ 1.634680] pcieport 0000:00:00.0: AER: enabled with IRQ 30
[ 1.645709] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 1.695627] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 1.702568] nand: Micron MT29F2G08ABBGAH4
[ 1.709022] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.712912] nand: WARNING: qcom_nand.0: the ECC used on your system (4b/512B) is too weak compared to the one required by the NAND chip (8b/512B)
[ 1.730236] 23 qcomsmem partitions found on MTD device qcom_nand.0
[ 1.733596] Creating 23 MTD partitions on "qcom_nand.0":
[ 1.739635] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.746507] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.751225] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.755803] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.761140] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.768632] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.773830] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.776767] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.781903] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.787553] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.792358] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.797300] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.802089] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.807303] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.811971] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.817216] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.822951] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.828032] 0x000000f80000-0x000001020000 : "0:art"
[ 1.833176] 0x000001020000-0x000007520000 : "rootfs"
[ 1.914811] mtd: setting mtd18 (rootfs) as root device
[ 1.915595] mtdsplit: error occured while reading from "rootfs"
[ 1.918886] 0x000007520000-0x000007e20000 : "0:wififw"
[ 1.932015] 0x000007e20000-0x00000e320000 : "rootfs_1"
[ 2.009858] 0x00000e320000-0x00000ec20000 : "0:wififw_1"
[ 2.017247] 0x00000ec20000-0x00000eca0000 : "0:ethphyfw"
[ 2.028094] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 2.030250] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 2.038329] clk: Disabling unused▒[ 2.051002] Freeing unused kernel memory: 9600K
[ 2.051081] Run /init as init process
[ 2.206312] init: Console is alive
[ 2.206451] init: - watchdog -
[ 2.215115] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.233279] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.247999] ssdk_dt_parse_interrupt[942]:INFO:intr-gpio does not exist
[ 2.286399] ssdk_phy_driver_init[341]:INFO:dev_id = 0, phy_adress = 28, phy_id = 0xffffffff phytype doesn't match
[ 3.263378] regi_init[2525]:INFO:Initializing HPPE Done!!
[ 3.263499] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[ 3.269990] EDMA ver 1 hw init
[ 3.274089] EDMA HW Reset completed succesfully
[ 3.276737] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 3.281132] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 3.286842] GMAC4(ffffff8003657980) Invalid MAC@ - using e2:19:64:f5:2d:82
[ 3.353387] nss-dp 3a001600.dp4 lan (uninitialized): failed to connect to phy device
[ 3.463341] nss-dp 3a001600.dp4: probe with driver nss-dp failed with error -14
[ 3.463490] GMAC6(ffffff8003657980) Invalid MAC@ - using 56:e5:f4:cb:9e:9e
[ 4.103632] Qualcomm QCA8081 90000.mdio-1:1c: phy_poll_reset failed: -110
[ 4.103697] nss-dp 3a007000.dp6-syn wan (uninitialized): failed to connect to phy device
[ 4.109411] nss-dp 3a007000.dp6-syn: probe with driver nss-dp failed with error -14
[ 4.117664] **********************************************************
[ 4.124948] * NSS Data Plane driver
[ 4.131525] **********************************************************
[ 4.150622] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.150674] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 4.155181] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000808002000010
[ 4.162597] xhci-hcd xhci-hcd.1.auto: irq 45, io mem 0x08a00000
[ 4.172072] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.177847] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 4.183404] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.191278] hub 1-0:1.0: USB hub found
[ 4.197618] hub 1-0:1.0: 1 port detected
[ 4.201474] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.205594] hub 2-0:1.0: USB hub found
[ 4.213526] hub 2-0:1.0: 1 port detected
[ 4.217300] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.221073] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[ 4.226504] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000808002000010
[ 4.233963] xhci-hcd xhci-hcd.2.auto: irq 46, io mem 0x08c00000
[ 4.243448] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 4.249198] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[ 4.254761] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 4.262622] hub 3-0:1.0: USB hub found
[ 4.268915] hub 3-0:1.0: 1 port detected
[ 4.272825] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.276947] hub 4-0:1.0: USB hub found
[ 4.284798] hub 4-0:1.0: 1 port detected
[ 4.289688] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.293491] init: - preinit -
[ 14.563604] platform leds: deferred probe pending: (reason unknown)
[ 14.853325] random: crng init done
Cannot parse config file '/etc/fw_env.config': No such file or directory
Failed to find NVMEM device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 18.994089] procd: - early -
[ 18.994202] procd: - watchdog -
[ 19.519726] procd: - watchdog -
[ 19.519963] procd: - ubus -
[ 19.674325] procd: - init -
Please press Enter to activate this console.
[ 19.798938] kmodloader: loading kernel modules from /etc/modules.d/*
[ 19.884347] usbcore: registered new interface driver cdc_wdm
[ 19.884792] Loading modules backported from Linux version v6.12.6-0-ge9d65b48ce1a
[ 19.889083] Backport generated by backports.git v6.1.110-1-35-g410656ef04d2
[ 19.901670] NET: Registered PF_QIPCRTR protocol family
[ 19.906258] usbcore: registered new interface driver usbserial_generic
[ 19.908469] usbserial: USB Serial support registered for generic
[ 19.946238] PPP generic driver version 2.4.2
[ 19.947089] NET: Registered PF_PPPOX protocol family
[ 19.950438] usbcore: registered new interface driver qmi_wwan
[ 19.960193] urngd: v1.0.2 started.
[ 19.963569] ath11k c000000.wifi: ipq8074 hw2.0
[ 19.963605] ath11k c000000.wifi: FW memory mode: 0
[ 19.985541] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 19.985643] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 20.336873] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 20.380831] ath11k c000000.wifi: qmi fail to get qcom,m3-dump-addr, ignore m3 dump mem req
[ 20.388299] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[ 20.388337] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
[ 20.465331] ath11k c000000.wifi: qmi failed to load CAL data file:cal-ahb-c000000.wifi.bin
[ 20.465412] ath11k c000000.wifi: failed to load board data file: -12
[ 32.483383] l11: disabling
[ 84.963368] ath11k c000000.wifi: Coldboot Calibration timed out
[ 84.965679] usbcore: registered new interface driver option
[ 84.968135] usbserial: USB Serial support registered for GSM modem (1-port)
[ 84.975505] kmodloader: done loading kernel modules from /etc/modules.d/*