OpenWrt for AP6510agn is it possible? what is needed?

For Developers
1

Alguna Orientación?, Gracias de Antemano.

HARDWARE INFO

AR934x WiSoC, AR9582 (AR9582-AR1A), and a 88E1512-NNP2

IMG_20190430_150340727
IMG_20190430_1503407271087×815 184 KB

LOG bootloader Breed

DRAM: 128MB
Platform: Atheros AR9344 rev 2
Board: Huawei 
Clocks: CPU: 560MHz, DDR: 450MHz, AHB: 225MHz, Ref: 40MHz
Flash: Micron M25P64 (8MB) on ath79-spi.0
ag71xx-eth: Using MAC address 64:70:02:b5:d7:46
ag71xx-eth.0: no PHY/switch found (0141:0dd1)
eth0: Generic PHY driver

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 5
Autoboot aborted due to key press.

Starting breed built-in shell

breed>
breed> boot flash 20000
Trying to boot firmware from 0x00020000 in flash bank 0 ...
Reading data into memory ...
U-Boot firmware image header detected.
    Image Name:   MIPS OpenWrt Linux-4.14.171
    Data Size:    1586152 Bytes
    Load Address: 80060000
    Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...

[    0.000000] Linux version 4.14.171 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10947-65030d81f3)) #0 Thu Feb 27 21:05:12 2020
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from 0x804ee740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124292K/131072K available (3947K kernel code, 192K rwdata, 516K rodata, 328K init, 212K bss, 6780K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
[    0.000009] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
[    0.008694] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.085638] pid_max: default: 32768 minimum: 301
[    0.090996] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098391] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.108444] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.119429] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.127393] NET: Registered protocol family 16
[    0.133661] MIPS: machine is Generic AR71XX/AR724X/AR913X based board
[    0.156764] clocksource: Switched to clocksource MIPS
[    0.163514] NET: Registered protocol family 2
[    0.169275] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.177099] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.184188] TCP: Hash tables configured (established 1024 bind 1024)
[    0.191419] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.197981] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.205198] NET: Registered protocol family 1
[    0.213834] Crashlog allocated RAM at address 0x3f00000
[    0.220984] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.233386] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.239933] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.260257] io scheduler noop registered
[    0.264630] io scheduler deadline registered (default)
[    0.270808] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.280083] console [ttyS0] disabled
[    0.304156] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A

Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <hackpascal@gmail.com>
Build date 2017-12-26 [git-812ef5f]
Version 1.1 (r1163)

DRAM: 128MB
Platform: Atheros AR9344 rev 2
Board: Huawei
Clocks: CPU: 560MHz, DDR: 450MHz, AHB: 225MHz, Ref: 40MHz
Flash: Micron M25P64 (8MB) on ath79-spi.0
ag71xx-eth: Using MAC address 64:70:02:b5:d7:46
ag71xx-eth.0: no PHY/switch found (0141:0dd1)
eth0: Generic PHY driver

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 3
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <hackpascal@gmail.com>
Build date 2017-12-26 [git-812ef5f]
Version 1.1 (r1163)

ubootOriginal

FULL FLASH SPI

Partitions

512k(BiosA)		1	512	00000-80000	
128k(BootupA)		2	128	80000-A0000	
128k(BootupB)		3	128	A0000-C0000	
128k(BootEnv)		4	128	C0000-E0000	
128k(BoardData)		5	128	E0000-100000	
12288k(SysImageA)	6	12288	100000-D00000	
3072k(configA)		7	3072	D00000-1000000	
512k(BiosB)		8	512	1000000-1080000	
128k(ResultA)		9	128	1080000-10A0000	
128k(ResultB)		10	128	10A0000-10C0000	
12288k(SysImageB)	11	12288	10C0000-1CC0000	
3072k(configB)		12	3072		
256k(ArtArgs);		13	256		
Total				32768
2

https://wikidevi.wi-cat.ru/Huawei_AP6510DN-AGN-US

FOTOS

3
4

1-160R21624220-L
1-160R21624220-L736×502 29.2 KB

5 
DRAM:  128 MB
Press CTRL+T for Full Memory Test in 1 Seconds:  0
Start up the normal boot...
DRAM:  128 MB
Press CTRL+T for Full Memory Test in 1 Seconds:  0

       ************************************************************
       **********************    *********    *********************
       ********************       *******       *******************
       ******************         *******         *****************
       ***********    ***          *****          ***    **********
       *********       ***         *****         ***      *********
       ********          **         ***         **         ********
       ********           **        ***        **          ********
       *********           **       ***       **          *********
       ***********          **      ***      **         ***********
       *****      ***         **    ***    **        ***      *****
       *****          ***      **  *****  **     ***          *****
       ******             ***   **********   ***             ******
       *********                 ********                 *********
       ************************************************************
       **********             **************             **********
       *************  ******************************  *************
       ************************************************************
                        Welcome To HUAWEI AP World                  

UBoot V200R002 version-044 (sep 27 2013 - 03:15:10)
Flash: 32 MB
PCIE:  PCIe Clock 40MHz
*** Warning *** : PCIe WLAN Module not found !!!
Ethernet Mac: 04-F9-38-E6-E4-C0
Image: Current Bootup is A
Image: Current Bootup is A
Current master bootup parameter area is B
Boot Kernel A Address: 0x9f490000
Boot Kernel B Address: 0x9f820000
Press j or J to stop Bus-Test in 1 seconds:   0
Bus test starting...
Board Type Mismatch, No PCIE Device!
SPI   bus  test OK.
DDR   bus  test OK.
RGMII bus  test OK.
Bus test ending...
Save Bus Test Result Successful
Press f or F  to stop Auto-Boot in 3 seconds:  0
   Uncompressing Kernel Image ... OK
Starting kernel ...
Booting Atheros AR934x
init_bsp_adapter ...OK.
mm_init ...OK.
sched_init ...OK.
softirq_init ...OK.
console_init ...OK.
thread_info_cache_init ...OK.
fork_init ...OK.
dbg_late_init ...OK.
imv_init_complete ...OK.
Linux version 2.6.34.15-WR4.3.0.0_standard (gcc version 4.5.2 (Sourcery CodeBench Lite 2011.03-93) )
#1 PREEMPT Mon Oct 26 20:15:21 CST 2015
flash_size passed from bootloader = 32 MB
arg 1: console=ttyS0,9600
arg 2: root=/dev/mtdblock5
arg 3: rootfstype=squashfs
arg 4: init=/sbin/init
arg 5: mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs);
arg 6: mem=126M
ath_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZ
Zone PFN ranges:
  Normal   0x00000000 -> 0x00007e00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00007e00
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32004
Kernel command line: console=ttyS0,9600 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs); mem=126M
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
FWD_MEM: aligned address 82000000
FWD_MEM: 02000000
FWD_MEM: Allocating 19MB (4864 pages) of memory at addr 82000000
the pci irq_base value: 70
plat_time_init:.............................................................done
Mount-cache hash table entries: 512
Registering WDT.............................................................done
ath_pcibios_init: bus 0
***** Warning PCIe 0 H/W not found !!!
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
ath_init_ioctl..............................................................done
init_vdso successfull
mtd: no mtd-id
ath_flash_init..............................................................done
Registering OTP.............................................................done
Registering Clock Switch Interface..........................................done
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
starting pid 21, tty '': '/etc/init.d/rcS'
MSS_PUB Version [1.07], build on Date : [Oct 26 2015], Time : [20:26:28]
Disabling lock debugging due to kernel taint
mii_bus 0 successed to register
MIMC_KERNEL: Module init.
eth-diag install ok!
Drv_ap_api module:Init
Mount fsimage type: patch
User fs folder    : /opt
Loop device       : /dev/loop0
Mount folder      : /mnt/patch
cap32 start, build time 20:23:31
MSS_PUB Version [1.07], build on Date : [Oct 26 2015], Time : [20:23:14]
MSS_PUB_Init Succ! u32Ret = 0
AP_Board_Cfg Succ!  u32Ret = 0
Module MEM Init         ...... OK!
Module DIAG Init        ...... OK!
Module PBUF Init        ...... OK!
Module IM Init          ...... OK!
Module IIC Init         ...... OK!
Module HAL Init         ...... OK!
Module Timer Init       ...... OK!
Module TIME Init        ...... OK!
MSS_Global_Init Succ! ret = 0
MSC Process run on core [0], PID = [68]
MSU Process run on core [0], PID = [69]
MSC_TCTL_Init Succ!  u32Ret = 0
MSC goto scheduler!
MSU_InstReg return 0x0
CAP_FWDIF_Init return 0x0
L1_IP_Fast_BaseAddrInit return 0x0
MSU_TableBaseInit return 0x0
MSU Init OK
VOS_Start ......
......OK
VRP_SockTm_Init create............OK
System recover configuration ........OK!


  Press any key to get started